[ Upstream commit 6d8e294bf5 ]
When inserting random PFNs for debugging the CEC through
(debugfs)/ras/cec/pfn, depending on the return value of pfn_set(),
multiple values get inserted per a single write.
That is because simple_attr_write() interprets a retval of 0 as
success and claims the whole input. However, pfn_set() returns the
cec_add_elem() value, which, if > 0 and smaller than the whole input
length, makes glibc continue issuing the write syscall until there's
input left:
pfn_set
simple_attr_write
debugfs_attr_write
full_proxy_write
vfs_write
ksys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
leading to those repeated calls.
Return 0 to fix that.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04310324c6 ]
When a CQ-enabled device uses QEBSM for SBAL state inspection,
get_buf_states() can return the PENDING state for an Output Queue.
get_outbound_buffer_frontier() isn't prepared for this, and any PENDING
buffer will permanently stall all further completion processing on this
Queue.
This isn't a concern for non-QEBSM devices, as get_buf_states() for such
devices will manually turn PENDING buffers into EMPTY ones.
Fixes: 104ea556ee ("qdio: support asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de44285c1 ]
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a19a058236 ]
When a valid MAC address is not found the current messages
are shown:
fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa
Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:
fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa
Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee326fd01e ]
Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.
Fixes: 477286b53f ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04507c0a93 ]
To set frequency on specific cpus using cpupower, following syntax can
be used :
cpupower -c #i frequency-set -f #f -r
While setting frequency using cpupower frequency-set command, if we use
'-r' option, it is expected to set frequency for all cpus related to
cpu #i. But it is observed to be missing the last cpu in related cpu
list. This patch fixes the problem.
Signed-off-by: Abhishek Goel <huntbag@linux.vnet.ibm.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9349850e1 ]
The sequence
static DEFINE_WW_CLASS(test_ww_class);
struct ww_acquire_ctx ww_ctx;
struct ww_mutex ww_lock_a;
struct ww_mutex ww_lock_b;
struct ww_mutex ww_lock_c;
struct mutex lock_c;
ww_acquire_init(&ww_ctx, &test_ww_class);
ww_mutex_init(&ww_lock_a, &test_ww_class);
ww_mutex_init(&ww_lock_b, &test_ww_class);
ww_mutex_init(&ww_lock_c, &test_ww_class);
mutex_init(&lock_c);
ww_mutex_lock(&ww_lock_a, &ww_ctx);
mutex_lock(&lock_c);
ww_mutex_lock(&ww_lock_b, &ww_ctx);
ww_mutex_lock(&ww_lock_c, &ww_ctx);
mutex_unlock(&lock_c); (*)
ww_mutex_unlock(&ww_lock_c);
ww_mutex_unlock(&ww_lock_b);
ww_mutex_unlock(&ww_lock_a);
ww_acquire_fini(&ww_ctx); (**)
will trigger the following error in __lock_release() when calling
mutex_release() at **:
DEBUG_LOCKS_WARN_ON(depth <= 0)
The problem is that the hlock merging happening at * updates the
references for test_ww_class incorrectly to 3 whereas it should've
updated it to 4 (representing all the instances for ww_ctx and
ww_lock_[abc]).
Fix this by updating the references during merging correctly taking into
account that we can have non-zero references (both for the hlock that we
merge into another hlock or for the hlock we are merging into).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: =?UTF-8?q?Ville=20Syrj=C3=A4l=C3=A4?= <ville.syrjala@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/20190524201509.9199-2-imre.deak@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621ccc6cc5 ]
Rename _P to _P_VAL and _R to _R_VAL to avoid global
namespace conflicts:
drivers/media/dvb-frontends/tua6100.c: In function ‘tua6100_set_params’:
drivers/media/dvb-frontends/tua6100.c:79: warning: "_P" redefined
#define _P 32
In file included from ./include/acpi/platform/aclinux.h:54,
from ./include/acpi/platform/acenv.h:152,
from ./include/acpi/acpi.h:22,
from ./include/linux/acpi.h:34,
from ./include/linux/i2c.h:17,
from drivers/media/dvb-frontends/tua6100.h:30,
from drivers/media/dvb-frontends/tua6100.c:32:
./include/linux/ctype.h:14: note: this is the location of the previous definition
#define _P 0x10 /* punct */
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9cca7034b ]
The MPC885 reference manual states:
SEC Lite-initiated 8xx writes can occur only on 32-bit-word boundaries, but
reads can occur on any byte boundary. Writing back a header read from a
non-32-bit-word boundary will yield unpredictable results.
In order to ensure that, cra_alignmask is set to 3 for SEC1.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 9c4a79653b ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eae55a586c ]
The driver assumes that the ICV is as a single piece in the last
element of the scatterlist. This assumption is wrong.
This patch ensures that the ICV is properly handled regardless of
the scatterlist layout.
Fixes: 9c4a79653b ("crypto: talitos - Freescale integrated security engine (SEC) driver")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82c76aca81 ]
In general, we don't want MAC drivers calling phy_attach_direct with the
net_device being NULL. Add checks against this in all the functions
calling it: phy_attach() and phy_connect_direct().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6995a65910 ]
Fix to avoid possible memory leak if the decoder initialization
got failed.Free the allocated memory for file handle object
before return in case decoder initialization fails.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 518fa4e0e0 ]
You can't memset the contents of a __user pointer. Instead, call copy_to_user to
copy links.reserved (which is zeroed) to the user memory.
This fixes this sparse warning:
SPARSE:drivers/media/mc/mc-device.c drivers/media/mc/mc-device.c:521:16: warning: incorrect type in argument 1 (different address spaces)
Fixes: f49308878d ("media: media_device_enum_links32: clean a reserved field")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeacfdc68a ]
Replace some BUG_ON()s with WARN_ON_ONCE() and returning an error code,
and move the check for len divisible by FS_CRYPTO_BLOCK_SIZE into
fscrypt_crypt_block() so that it's done for both encryption and
decryption, not just encryption.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38ff4075a ]
Family of src/dst can be different from family of selector src/dst.
Use xfrm selector family to validate address prefix length,
while verifying new sa from userspace.
Validated patch with this command:
ip xfrm state add src 1.1.6.1 dst 1.1.6.2 proto esp spi 4260196 \
reqid 20004 mode tunnel aead "rfc4106(gcm(aes))" \
0x1111016400000000000000000000000044440001 128 \
sel src 1011:1:4::2/128 sel dst 1021:1:4::2/128 dev Port5
Fixes: 07bf790895 ("xfrm: Validate address prefix lengths in the xfrm selector.")
Signed-off-by: Anirudh Gupta <anirudh.gupta@sophos.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9070dc945 ]
The locking in force_sig_info is not prepared to deal with a task that
exits or execs (as sighand may change). The is not a locking problem
in force_sig as force_sig is only built to handle synchronous
exceptions.
Further the function force_sig_info changes the signal state if the
signal is ignored, or blocked or if SIGNAL_UNKILLABLE will prevent the
delivery of the signal. The signal SIGKILL can not be ignored and can
not be blocked and SIGNAL_UNKILLABLE won't prevent it from being
delivered.
So using force_sig rather than send_sig for SIGKILL is confusing
and pointless.
Because it won't impact the sending of the signal and and because
using force_sig is wrong, replace force_sig with send_sig.
Cc: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Serge Hallyn <serge@hallyn.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Fixes: cf3f89214e ("pidns: add reboot_pid_ns() to handle the reboot syscall")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f49308878d ]
In v4l2-compliance utility, test MEDIA_IOC_ENUM_ENTITIES
will check whether reserved field of media_links_enum filled
with zero.
However, for 32 bit program, the reserved field is missing
copy from kernel space to user space in media_device_enum_links32
function.
This patch adds the cleaning a reserved field logic in
media_device_enum_links32 function.
Signed-off-by: Jungo Lin <jungo.lin@mediatek.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c7aa32966 ]
The commit d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Fixes: d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e03e79286 ]
Selftests report the following:
[ 2.984845] alg: skcipher: cbc-aes-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 2.995377] 00000000: 3d af ba 42 9d 9e b4 30 b4 22 da 80 2c 9f ac 41
[ 3.032673] alg: skcipher: cbc-des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.043185] 00000000: fe dc ba 98 76 54 32 10
[ 3.063238] alg: skcipher: cbc-3des-talitos encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
[ 3.073818] 00000000: 7d 33 88 93 0f 93 b2 42
This above dumps show that the actual output IV is indeed the input IV.
This is due to the IV not being copied back into the request.
This patch fixes that.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24e4cf7703 ]
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
After this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
alias: of:N*T*Cir-spi-ledC*
alias: of:N*T*Cir-spi-led
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d6751eaff ]
The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements. We need to add a couple bounds
checks to prevent array overflows.
I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.
Fixes: bdcd817079 (" Add ath6kl cleaned up driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f90c7e5d0 ]
Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97354f2c43 ]
Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to
firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfabdd6997 ]
Notice that *rc* can evaluate to up to 5, include/linux/netdevice.h:
enum gro_result {
GRO_MERGED,
GRO_MERGED_FREE,
GRO_HELD,
GRO_NORMAL,
GRO_DROP,
GRO_CONSUMED,
};
typedef enum gro_result gro_result_t;
In case *rc* evaluates to 5, we end up having an out-of-bounds read
at drivers/net/wireless/ath/wil6210/txrx.c:821:
wil_dbg_txrx(wil, "Rx complete %d bytes => %s\n",
len, gro_res_str[rc]);
Fix this by adding element "GRO_CONSUMED" to array gro_res_str.
Addresses-Coverity-ID: 1444666 ("Out-of-bounds read")
Fixes: 194b482b50 ("wil6210: Debug print GRO Rx result")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b8066c3de ]
If probe() fails anywhere beyond the point where
sdma_get_firmware() is called, then a kernel oops may occur.
Problematic sequence of events:
1. probe() calls sdma_get_firmware(), which schedules the
firmware callback to run when firmware becomes available,
using the sdma instance structure as the context
2. probe() encounters an error, which deallocates the
sdma instance structure
3. firmware becomes available, firmware callback is
called with deallocated sdma instance structure
4. use after free - kernel oops !
Solution: only attempt to load firmware when we're certain
that probe() will succeed. This guarantees that the firmware
callback's context will remain valid.
Note that the remove() path is unaffected by this issue: the
firmware loader will increment the driver module's use count,
ensuring that the module cannot be unloaded while the
firmware callback is pending or running.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: fixed braces for if condition]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd6c49339 ]
If the CHAP_A value is not supported, the chap_server_open() function
should free the auth_protocol pointer and set it to NULL, or we will leave
a dangling pointer around.
[ 66.010905] Unsupported CHAP_A value
[ 66.011660] Security negotiation failed.
[ 66.012443] iSCSI Login negotiation failed.
[ 68.413924] general protection fault: 0000 [#1] SMP PTI
[ 68.414962] CPU: 0 PID: 1562 Comm: targetcli Kdump: loaded Not tainted 4.18.0-80.el8.x86_64 #1
[ 68.416589] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 68.417677] RIP: 0010:__kmalloc_track_caller+0xc2/0x210
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa69fb62be ]
After r363059 and r363928 in LLVM, a build using ld.lld as the linker
with CONFIG_RANDOMIZE_BASE enabled fails like so:
ld.lld: error: relocation R_AARCH64_ABS32 cannot be used against symbol
__efistub_stext_offset; recompile with -fPIC
Fangrui and Peter figured out that ld.lld is incorrectly considering
__efistub_stext_offset as a relative symbol because of the order in
which symbols are evaluated. _text is treated as an absolute symbol
and stext is a relative symbol, making __efistub_stext_offset a
relative symbol.
Adding ABSOLUTE will force ld.lld to evalute this expression in the
right context and does not change ld.bfd's behavior. ld.lld will
need to be fixed but the developers do not see a quick or simple fix
without some research (see the linked issue for further explanation).
Add this simple workaround so that ld.lld can continue to link kernels.
Link: https://github.com/ClangBuiltLinux/linux/issues/561
Link: 025a815d75
Link: 249fde8583
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Debugged-by: Fangrui Song <maskray@google.com>
Debugged-by: Peter Smith <peter.smith@linaro.org>
Suggested-by: Fangrui Song <maskray@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[will: add comment]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1196364f21 ]
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
^~~~~~~~~~
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db13a5ba27 ]
While trying to get the uart with parity working I found setting even
parity enabled odd parity insted. Fix the register settings to match
the datasheet of AR9331.
A similar patch was created by 8devices, but not sent upstream.
77c5586ade
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ecac85ead upstream.
This should help with some of the lifetime issues, and move us away
from load/unload.
[rez] Regarding the backport to v4.14.y, the only difference is due to
the fact that in v4.14.y the udl_usb_probe() function still uses
drm_dev_unref() instead of drm_dev_put().
Backport notes:
On Mon, Jul 15, 2019 at 09:13:08PM -0400, Sasha Levin wrote:
> Hm, we don't need ac3b35f11a here? Why not? I'd love to document that
> with the backport.
Nope, we don't need that patch in the v4.14 backport.
In v4.19.y we have two functions, drm_dev_put() and drm_dev_unref(), which are
aliases for one another (drm_dev_unref() just calls drm_dev_put()).
drm_dev_unref() is the older of the two, and was introduced back in v4.0.
drm_dev_put() was introduced in v4.15 with
9a96f55034 drm: introduce drm_dev_{get/put} functions
and slowly callers were moved from the old name (_unref) to the new name
(_put). The patch you mentioned, ac3b35f11a, is one such patch where we are
replacing a drm_dev_unref() call with a drm_dev_put() call. This doesn't have
a functional change, but was necessary so that the third patch in the v4.19.y
series I sent would apply cleanly.
For the v4.14.y series, though, the drm_dev_put() function hasn't yet been
defined and everyone is still using drm_dev_unref(). So, we don't need a
backport of ac3b35f11a, and I also had a small backport change in the last
patch of the v4.14.y series where I had to change a drm_dev_put() call with a
drm_dev_unref() call.
Just for posterity, the drm_dev_unref() calls were eventually all changed to
drm_dev_put() in v5.0, and drm_dev_unref() was removed entirely. That
happened with the following two patches:
808bad32ea drm: replace "drm_dev_unref" function with "drm_dev_put"
ba1d345401 drm: remove deprecated "drm_dev_unref" function
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405031715.5959-4-airlied@gmail.com
Signed-off-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e52d484d98 upstream.
System gets checkstop if RxFIFO overruns with more requests than the
maximum possible number of CRBs in FIFO at the same time. The max number
of requests per window is controlled by window credits. So find max
CRBs from FIFO size and set it to receive window credits.
Fixes: b0d6c9bab5 ("crypto/nx: Add P9 NX support for 842 compression engine")
CC: stable@vger.kernel.org # v4.14+
Signed-off-by:Haren Myneni <haren@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
commit ac6639cd3d upstream.
Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.
Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.
Fixes: d0c9d4a89f ("[S390] qdio: set correct bit in dsci")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54e4785cb upstream.
When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.
If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.
For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.
setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f18d869ff upstream.
The stfle inline assembly returns the number of double words written
(condition code 0) or the double words it would have written
(condition code 3), if the memory array it got as parameter would have
been large enough.
The current stfle implementation assumes that the array is always
large enough and clears those parts of the array that have not been
written to with a subsequent memset call.
If however the array is not large enough memset will get a negative
length parameter, which means that memset clears memory until it gets
an exception and the kernel crashes.
To fix this simply limit the maximum length. Move also the inline
assembly to an extra function to avoid clobbering of register 0, which
might happen because of the added min_t invocation together with code
instrumentation.
The bug was introduced with commit 14375bc4eb ("[S390] cleanup
facility list handling") but was rather harmless, since it would only
write to a rather large array. It became a potential problem with
commit 3ab121ab18 ("[S390] kernel: Add z/VM LGR detection"). Since
then it writes to an array with only four double words, while some
machines already deliver three double words. As soon as machines have
a facility bit within the fifth double a crash on IPL would happen.
Fixes: 14375bc4eb ("[S390] cleanup facility list handling")
Cc: <stable@vger.kernel.org> # v2.6.37+
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33d4a5a7a5 ]
Setting invalid value to /sys/devices/system/cpu/cpuX/hotplug/fail
can control `struct cpuhp_step *sp` address, results in the following
global-out-of-bounds read.
Reproducer:
# echo -2 > /sys/devices/system/cpu/cpu0/hotplug/fail
KASAN report:
BUG: KASAN: global-out-of-bounds in write_cpuhp_fail+0x2cd/0x2e0
Read of size 8 at addr ffffffff89734438 by task bash/1941
CPU: 0 PID: 1941 Comm: bash Not tainted 5.2.0-rc6+ #31
Call Trace:
write_cpuhp_fail+0x2cd/0x2e0
dev_attr_store+0x58/0x80
sysfs_kf_write+0x13d/0x1a0
kernfs_fop_write+0x2bc/0x460
vfs_write+0x1e1/0x560
ksys_write+0x126/0x250
do_syscall_64+0xc1/0x390
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f05e4f4c970
The buggy address belongs to the variable:
cpu_hotplug_lock+0x98/0xa0
Memory state around the buggy address:
ffffffff89734300: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
ffffffff89734380: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
>ffffffff89734400: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
^
ffffffff89734480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffff89734500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Add a sanity check for the value written from user space.
Fixes: 1db49484f2 ("smp/hotplug: Hotplug state fail injection")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Link: https://lkml.kernel.org/r/20190627024732.31672-1-devel@etsukata.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81c7ed296d ]
A kernel which boots in 5-level paging mode crashes in a small percentage
of cases if KASLR is enabled.
This issue was tracked down to the case when the kernel image unpacks in a
way that it crosses an 1G boundary. The crash is caused by an overrun of
the PMD page table in __startup_64() and corruption of P4D page table
allocated next to it. This particular issue is not visible with 4-level
paging as P4D page tables are not used.
But the P4D and the PUD calculation have similar problems.
The PMD index calculation is wrong due to operator precedence, which fails
to confine the PMDs in the PMD array on wrap around.
The P4D calculation for 5-level paging and the PUD calculation calculate
the first index correctly, but then blindly increment it which causes the
same issue when a kernel image is located across a 512G and for 5-level
paging across a 46T boundary.
This wrap around mishandling was introduced when these parts moved from
assembly to C.
Restore it to the correct behaviour.
Fixes: c88d71508e ("x86/boot/64: Rewrite startup_64() in C")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190620112345.28833-1-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2eba4e640b ]
DM verity should also use DMERR_LIMIT to limit repeat data block
corruption messages.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
