commit d1d90dd272 upstream.
commit 72704f876f ("dwc3: gadget: Implement the suspend entry event
handler") introduced (nearly 5 years ago!) an interrupt handler for
U3/L1-L2 suspend events. The problem is that these events aren't
currently enabled in the DEVTEN register so the handler is never
even invoked. Fix this simply by enabling the corresponding bit
in dwc3_gadget_enable_irq() using the same revision check as found
in the handler.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210428090111.3370-1-jackp@codeaurora.org
[jackp@codeaurora.org: backport to pre-5.7 by replacing
DWC3_IS_VER_PRIOR check with direct comparison of dwc->revision]
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a703619127 upstream.
In 801c6058d1 ("bpf: Fix leakage of uninitialized bpf stack under
speculation") we replaced masking logic with direct loads of immediates
if the register is a known constant. Given in this case we do not apply
any masking, there is also no reason for the operation to be truncated
under the speculative domain.
Therefore, there is also zero reason for the verifier to branch-off and
simulate this case, it only needs to do it for unknown but bounded scalars.
As a side-effect, this also enables few test cases that were previously
rejected due to simulation under zero truncation.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb01a1bba5 upstream.
Masking direction as indicated via mask_to_left is considered to be
calculated once and then used to derive pointer limits. Thus, this
needs to be placed into bpf_sanitize_info instead so we can pass it
to sanitize_ptr_alu() call after the pointer move. Piotr noticed a
corner case where the off reg causes masking direction change which
then results in an incorrect final aux->alu_limit.
Fixes: 7fedb63a83 ("bpf: Tighten speculative pointer arithmetic mask")
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d0220f686 upstream.
Add a container structure struct bpf_sanitize_info which holds
the current aux info, and update call-sites to sanitize_ptr_alu()
to pass it in. This is needed for passing in additional state
later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f053cf7aa6 upstream.
ext4 didn't properly clean up if verity failed to be enabled on a file:
- It left verity metadata (pages past EOF) in the page cache, which
would be exposed to userspace if the file was later extended.
- It didn't truncate the verity metadata at all (either from cache or
from disk) if an error occurred while setting the verity bit.
Fix these bugs by adding a call to truncate_inode_pages() and ensuring
that we truncate the verity metadata (both from cache and from disk) in
all error paths. Also rework the code to cleanly separate the success
path from the error paths, which makes it much easier to understand.
Reported-by: Yunlei He <heyunlei@hihonor.com>
Fixes: c93d8f8858 ("ext4: add basic fs-verity support")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210302200420.137977-2-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e1f689913 upstream.
nvme_init_identify and thus nvme_mpath_init can be called multiple
times and thus must not overwrite potentially initialized or in-use
fields. Split out a helper for the basic initialization when the
controller is initialized and make sure the init_identify path does
not blindly change in-use data structures.
Fixes: 0d0b660f21 ("nvme: add ANA support")
Reported-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 860dafa902 upstream.
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d076336 ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
References:
[1] https://syzkaller.appspot.com/bug?id=32577e96d88447ded2d3b76d71254fb855245837
[2] https://syzkaller.appspot.com/bug?id=6b8355d27b2b94fb5cedf4655e3a59162d9e48e3
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d0ad57b3 upstream.
Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.
Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.
Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: e400b6ec4e ("vt/vgacon: Check if screen resize request comes from userspace")
Cc: stable@vger.kernel.org # v2.6.24+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a73b6a3b41 upstream.
In commit b05ae01fdb, someone tried to make the driver handle i2c read
errors by simply zeroing out the register contents, but for some reason
left unaltered the code that sets the cached register value the function
call return value.
The original patch was authored by a member of the Underhanded
Mangle-happy Nerds, I'm not terribly surprised. I don't have the
hardware anymore so I can't test this, but it seems like a pretty
obvious API usage fix to me...
Fixes: b05ae01fdb ("misc/ics932s401: Add a missing check to i2c_smbus_read_word_data")
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210428222534.GJ3122264@magnolia
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6e337708c upstream.
niu_pci_eeprom_read() may fail, so add checks to its return value and
propagate the error up the callstack.
An examination of the callstack up to niu_pci_eeprom_read shows that:
niu_pci_eeprom_read() // returns int
niu_pci_vpd_scan_props() // returns int
niu_pci_vpd_fetch() // returns *void*
niu_get_invariants() // returns int
since niu_pci_vpd_fetch() returns void which breaks the bubbling up,
change its return type to int so that error is propagated upwards.
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Cc: Shannon Nelson <shannon.lee.nelson@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-24-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7930742d6a upstream.
This reverts commit 26fd962bde.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change here was incorrect. While it is nice to check if
niu_pci_eeprom_read() succeeded or not when using the data, any error
that might have happened was not propagated upwards properly, causing
the kernel to assume that these reads were successful, which results in
invalid data in the buffer that was to contain the successfully read
data.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Shannon Nelson <shannon.lee.nelson@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 26fd962bde ("niu: fix missing checks of niu_pci_eeprom_read")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-23-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b95b57dfe7 upstream.
This reverts commit 5bf7295fe3.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit does not properly detect if an error happens because the
logic after this loop will not detect that there was a failed
allocation.
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 5bf7295fe3 ("qlcnic: Avoid potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-25-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c5634c4a upstream.
This reverts commit 765976285a.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Bryan Brattlof <hello@bryanbrattlof.com>
Fixes: 765976285a ("rtlwifi: fix a potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9183f01b5e upstream.
As Peter points out, if we were to disconnect and then reconnect this
driver from a device, the "global" state of the device would contain odd
values and could cause problems. Fix this up by just initializing the
whole thing to 0 at probe() time.
Ideally this would be a per-device variable, but given the age and the
total lack of users of it, that would require a lot of s/./->/g changes
for really no good reason.
Reported-by: Peter Rosin <peda@axentia.se>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/YJP2j6AU82MqEY2M@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d03d1021da upstream.
The fields, "toc" and "cd_info", of "struct gdrom_unit gd" are allocated
in "probe_gdrom()". Prevent a memory leak by making sure "gd.cd_info" is
deallocated in the "remove_gdrom()" function.
Also prevent double free of the field "gd.toc" by moving it from the
module's exit function to "remove_gdrom()". This is because, in
"probe_gdrom()", the function makes sure to deallocate "gd.toc" in case
of any errors, so the exit function invoked later would again free
"gd.toc".
The patch also maintains consistency by deallocating the above mentioned
fields in "remove_gdrom()" along with another memory allocated field
"gd.disk".
Suggested-by: Jens Axboe <axboe@kernel.dk>
Cc: Peter Rosin <peda@axentia.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-28-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 257343d3ed upstream.
This reverts commit 093c48213e.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
Because of this, all submissions from this group must be reverted from
the kernel tree and will need to be re-reviewed again to determine if
they actually are a valid fix. Until that work is complete, remove this
change to ensure that no problems are being introduced into the
codebase.
Cc: Wenwen Wang <wang6495@umn.edu>
Cc: Peter Rosin <peda@axentia.se>
Cc: Jens Axboe <axboe@kernel.dk>
Fixes: 093c48213e ("gdrom: fix a memory leak bug")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-27-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d427b408c upstream.
This reverts commit 63a06181d7.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit is incorrect, it does not properly clean up on the
error path, so I'll keep the revert and fix it up properly with a
follow-on patch.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 63a06181d7 ("scsi: ufs: fix a missing check of devm_reset_control_get")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-31-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1436df2f2 upstream.
This reverts commit 2c2a7552dd.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit log for this change was incorrect, no "error
handling code" was added, things will blow up just as badly as before if
any of these cases ever were true. As this BUG_ON() never fired, and
most of these checks are "obviously" never going to be true, let's just
revert to the original code for now until this gets unwound to be done
correctly in the future.
Cc: Aditya Pakki <pakki001@umn.edu>
Fixes: 2c2a7552dd ("ecryptfs: replace BUG_ON with error handling code")
Cc: stable <stable@vger.kernel.org>
Acked-by: Tyler Hicks <code@tyhicks.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-49-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed04fe8a0e upstream.
This reverts commit 1d84353d20.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here, while technically correct, did not fully
handle all of the reported issues that the commit stated it was fixing,
so revert it until it can be "fixed" fully.
Note, ioremap() probably will never fail for old hardware like this, and
if anyone actually used this hardware (a PowerMac era PCI display card),
they would not be using fbdev anymore.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Fixes: 1d84353d20 ("video: imsttfb: fix potential NULL pointer dereferences")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-67-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ae341767 upstream.
This reverts commit 9aa3aa15f4.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu>
Fixes: 9aa3aa15f4 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe")
Cc: stable <stable@vger.kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d1beda5f1 upstream.
This reverts commit 248b57015f.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit does not properly unwind if there is an error
condition so it needs to be reverted at this point in time.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 248b57015f ("leds: lp5523: fix a missing check of return value of lp55xx_read")
Link: https://lore.kernel.org/r/20210503115736.2104747-9-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bee1b05118 upstream.
This reverts commit f86a3b8383.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: David S. Miller <davem@davemloft.net>
Fixes: f86a3b8383 ("net: stmicro: fix a missing check of clk_prepare")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58c0cc2d90 upstream.
This reverts commit ec7f6aad57.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This patch "looks" correct, but the driver keeps on running and will
fail horribly right afterward if this error condition ever trips.
So points for trying to resolve an issue, but a huge NEGATIVE value for
providing a "fake" fix for the problem as nothing actually got resolved
at all. I'll go fix this up properly...
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Ferenc Bakonyi <fero@drama.obuda.kando.hu>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: ec7f6aad57 ("video: hgafb: fix potential NULL pointer dereference")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-39-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c699a0db2d upstream.
The following commands will crash the kernel:
modprobe brd rd_size=1048576
dmsetup create o --table "0 `blockdev --getsize /dev/ram0` snapshot-origin /dev/ram0"
dmsetup create s --table "0 `blockdev --getsize /dev/ram0` snapshot /dev/ram0 /dev/ram1 N 0"
The reason is that when we test for zero chunk size, we jump to the label
bad_read_metadata without setting the "r" variable. The function
snapshot_ctr destroys all the structures and then exits with "r == 0". The
kernel then crashes because it falsely believes that snapshot_ctr
succeeded.
In order to fix the bug, we set the variable "r" to -EINVAL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c81d3d2460 upstream.
When multiple PCI devices get assigned to a guest right at boot, libxl
incrementally populates the backend tree. The writes for the first of
the devices trigger the backend watch. In turn xen_pcibk_setup_backend()
will set the XenBus state to Initialised, at which point no further
reconfigures would happen unless a device got hotplugged. Arrange for
reconfigure to also get triggered from the backend watch handler.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/2337cbd6-94b9-4187-9862-c03ea12e0c61@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1149a6c06 upstream.
Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754f391584 upstream.
This reverts commit 32f4717983.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be not be needed at all as the
change was useless because this function can only be called when
of_match_device matched on something. So it should be reverted.
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Fixes: 32f4717983 ("serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference")
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
