[ Upstream commit ac5b70198a ]
netif_set_real_num_tx_queues() can be called when netdev is up.
That usually happens when user requests change of number of
channels/rings with ethtool -L. The procedure for changing
the number of queues involves resetting the qdiscs and setting
dev->num_tx_queues to the new value. When the new value is
lower than the old one, extra care has to be taken to ensure
ordering of accesses to the number of queues vs qdisc reset.
Currently the queues are reset before new dev->num_tx_queues
is assigned, leaving a window of time where packets can be
enqueued onto the queues going down, leading to a likely
crash in the drivers, since most drivers don't check if TX
skbs are assigned to an active queue.
Fixes: e6484930d7 ("net: allocate tx queues in register_netdevice")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca79bec237 ]
gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:
net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.
We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.
This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.
Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6c3bad1ba ]
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.
Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8c6db1dfd ]
In fib_nh_match(), if output interface or gateway are passed in
the FIB configuration, we don't have to check next hops of
multipath routes to conclude whether we have a match or not.
However, we might still have routes with different realms
matching the same output interface and gateway configuration,
and this needs to cause the match to fail. Otherwise the first
route inserted in the FIB will match, regardless of the realms:
# ip route add 1.1.1.1 dev eth0 table 1234 realms 1/2
# ip route append 1.1.1.1 dev eth0 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev eth0 scope link realms 1/2
1.1.1.1 dev eth0 scope link realms 3/4
# ip route del 1.1.1.1 dev ens3 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev ens3 scope link realms 3/4
whereas route with realms 3/4 should have been deleted instead.
Explicitly check for fc_flow passed in the FIB configuration
(this comes from RTA_FLOW extracted by rtm_to_fib_config()) and
fail matching if it differs from nh_tclassid.
The handling of RTA_FLOW for multipath routes later in
fib_nh_match() is still needed, as we can have multiple RTA_FLOW
attributes that need to be matched against the tclassid of each
next hop.
v2: Check that fc_flow is set before discarding the match, so
that the user can still select the first matching rule by
not specifying any realm, as suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b12580af1 ]
Now br_sysfs_if file flush doesn't have attr show. To read it will
cause kernel panic after users chmod u+r this file.
Xiong found this issue when running the commands:
ip link add br0 type bridge
ip link add type veth
ip link set veth0 master br0
chmod u+r /sys/devices/virtual/net/veth0/brport/flush
timeout 3 cat /sys/devices/virtual/net/veth0/brport/flush
kernel crashed with NULL a pointer dereference call trace.
This patch is to fix it by return -EINVAL when brport_attr->show
is null, just the same as the check for brport_attr->store in
brport_store().
Fixes: 9cf637473c ("bridge: add sysfs hook to flush forwarding table")
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backport of upstream commit 45d55e7bac ("x86/apic/vector: Fix off by
one in error path") missed to fixup the legacy interrupt data which is not
longer available upstream.
Handle legacy irq data correctly by clearing the legacy storage to prevent
use after free.
Fixes: 7fd1335392 ("x86/apic/vector: Fix off by one in error path") - 4.4.y
Fixes: c557481a94 ("x86/apic/vector: Fix off by one in error path") - 4.9.y
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b87b6194be upstream.
Before, if cb->start() failed, the module reference would never be put,
because cb->cb_running is intentionally false at this point. Users are
generally annoyed by this because they can no longer unload modules that
leak references. Also, it may be possible to tediously wrap a reference
counter back to zero, especially since module.c still uses atomic_inc
instead of refcount_inc.
This patch expands the error path to simply call module_put if
cb->start() fails.
Fixes: 41c87425a1 ("netlink: do not set cb_running if dump's start() errs")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39772f0a7b upstream.
The locking protocols in md assume that a device will
never be removed from an array during resync/recovery/reshape.
When that isn't happening, rcu or reconfig_mutex is needed
to protect an rdev pointer while taking a refcount. When
it is happening, that protection isn't needed.
Unfortunately there are cases were remove_and_add_spares() is
called when recovery might be happening: is state_store(),
slot_store() and hot_remove_disk().
In each case, this is just an optimization, to try to expedite
removal from the personality so the device can be removed from
the array. If resync etc is happening, we just have to wait
for md_check_recover to find a suitable time to call
remove_and_add_spares().
This optimization and not essential so it doesn't
matter if it fails.
So change remove_and_add_spares() to abort early if
resync/recovery/reshape is happening, unless it is called
from md_check_recovery() as part of a newly started recovery.
The parameter "this" is only NULL when called from
md_check_recovery() so when it is NULL, there is no need to abort.
As this can result in a NULL dereference, the fix is suitable
for -stable.
cc: yuyufen <yuyufen@huawei.com>
Cc: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Fixes: 8430e7e0af ("md: disconnect device from personality before trying to remove it.")
Cc: stable@ver.kernel.org (v4.8+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18bf3c3ea8 upstream.
Flush indirect branches when switching into a process that marked itself
non dumpable. This protects high value processes like gpg better,
without having too high performance overhead.
If done naïvely, we could switch to a kernel idle thread and then back
to the original process, such as:
process A -> idle -> process A
In such scenario, we do not have to do IBPB here even though the process
is non-dumpable, as we are switching back to the same process after a
hiatus.
To avoid the redundant IBPB, which is expensive, we track the last mm
user context ID. The cost is to have an extra u64 mm context id to track
the last mm we were using before switching to the init_mm used by idle.
Avoiding the extra IBPB is probably worth the extra memory for this
common scenario.
For those cases where tlb_defer_switch_to_init_mm() returns true (non
PCID), lazy tlb will defer switch to init_mm, so we will not be changing
the mm for the process A -> idle -> process A switch. So IBPB will be
skipped for this case.
Thanks to the reviewers and Andy Lutomirski for the suggestion of
using ctx_id which got rid of the problem of mm pointer recycling.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: ak@linux.intel.com
Cc: karahmed@amazon.de
Cc: arjan@linux.intel.com
Cc: torvalds@linux-foundation.org
Cc: linux@dominikbrodowski.net
Cc: peterz@infradead.org
Cc: bp@alien8.de
Cc: luto@kernel.org
Cc: pbonzini@redhat.com
Link: https://lkml.kernel.org/r/1517263487-3708-1-git-send-email-dwmw@amazon.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74402055a2 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84c7efd607 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb7695fe9 upstream.
If only a subset of the devices associated with multiple regions support
a given special operation (eg. DISCARD) then the dec_count() that is
used to set error for the region must increment the io->count.
Otherwise, when the dec_count() is called it can cause the dm-io
caller's bio to be completed multiple times. As was reported against
the dm-mirror target that had mirror legs with a mix of discard
capabilities.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=196077
Reported-by: Zhang Yi <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee8bdfb656 upstream.
Even though it is unconventional, some PCIe host implementations omit the
root ports entirely, and simply consist of a host bridge (which is not
modeled as a device in the PCI hierarchy) and a link.
When the downstream device is an endpoint, our current code does not seem
to mind this unusual configuration. However, when PCIe switches are
involved, the ASPM code assumes that any downstream switch port has a
parent, and blindly dereferences the bus->parent->self field of the pci_dev
struct to chain the downstream link state to the link state of the root
port. Given that the root port is missing, the link is not modeled at all,
and nor is the link state, and attempting to access it results in a NULL
pointer dereference and a crash.
Avoid this by allowing the link state chain to terminate at the downstream
port if no root port exists.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67870eb120 upstream.
In banked-sr.c, we use a top-level '__asm__(".arch_extension virt")'
statement to allow compilation of a multi-CPU kernel for ARMv6
and older ARMv7-A that don't normally support access to the banked
registers.
This is considered to be a programming error by the gcc developers
and will no longer work in gcc-8, where we now get a build error:
/tmp/cc4Qy7GR.s:34: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_usr'
/tmp/cc4Qy7GR.s:41: Error: Banked registers are not available with this architecture. -- `mrs r3,ELR_hyp'
/tmp/cc4Qy7GR.s:55: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_svc'
/tmp/cc4Qy7GR.s:62: Error: Banked registers are not available with this architecture. -- `mrs r3,LR_svc'
/tmp/cc4Qy7GR.s:69: Error: Banked registers are not available with this architecture. -- `mrs r3,SPSR_svc'
/tmp/cc4Qy7GR.s:76: Error: Banked registers are not available with this architecture. -- `mrs r3,SP_abt'
Passign the '-march-armv7ve' flag to gcc works, and is ok here, because
we know the functions won't ever be called on pre-ARMv7VE machines.
Unfortunately, older compiler versions (4.8 and earlier) do not understand
that flag, so we still need to keep the asm around.
Backporting to stable kernels (4.6+) is needed to allow those to be built
with future compilers as well.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84129
Fixes: 33280b4cd1 ("ARM: KVM: Add banked registers save/restore")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028091f82e upstream.
When the Intel Edison module is powered with 3.3V, the reboot command makes
the module stuck. If the module is powered at a greater voltage, like 4.4V
(as the Edison Mini Breakout board does), reboot works OK.
The official Intel Edison BSP sends the IPCMSG_COLD_RESET message to the
SCU by default. The IPCMSG_COLD_BOOT which is used by the upstream kernel
is only sent when explicitely selected on the kernel command line.
Use IPCMSG_COLD_RESET unconditionally which makes reboot work independent
of the power supply voltage.
[ tglx: Massaged changelog ]
Fixes: bda7b072de ("x86/platform/intel-mid: Implement power off sequence")
Signed-off-by: Sebastian Panceac <sebastian@resin.io>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1519810849-15131-1-git-send-email-sebastian@resin.io
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0373ca7483 upstream.
commit a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0adb24e03a upstream.
The change to flush_kernel_vmap_range() wasn't sufficient to avoid the
SMP stalls. The problem is some drivers call these routines with
interrupts disabled. Interrupts need to be enabled for flush_tlb_all()
and flush_cache_all() to work. This version adds checks to ensure
interrupts are not disabled before calling routines that need IPI
interrupts. When interrupts are disabled, we now drop into slower code.
The attached change fixes the ordering of cache and TLB flushes in
several cases. When we flush the cache using the existing PTE/TLB
entries, we need to flush the TLB after doing the cache flush. We don't
need to do this when we flush the entire instruction and data caches as
these flushes don't use the existing TLB entries. The same is true for
tmpalias region flushes.
The flush_kernel_vmap_range() and invalidate_kernel_vmap_range()
routines have been updated.
Secondly, we added a new purge_kernel_dcache_range_asm() routine to
pacache.S and use it in invalidate_kernel_vmap_range(). Nominally,
purges are faster than flushes as the cache lines don't have to be
written back to memory.
Hopefully, this is sufficient to resolve the remaining problems due to
cache speculation. So far, testing indicates that this is the case. I
did work up a patch using tmpalias flushes, but there is a performance
hit because we need the physical address for each page, and we also need
to sequence access to the tmpalias flush code. This increases the
probability of stalls.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c52232a49e upstream.
On CPU hotunplug the enqueued timers of the unplugged CPU are migrated to a
live CPU. This happens from the control thread which initiated the unplug.
If the CPU on which the control thread runs came out from a longer idle
period then the base clock of that CPU might be stale because the control
thread runs prior to any event which forwards the clock.
In such a case the timers from the unplugged CPU are queued on the live CPU
based on the stale clock which can cause large delays due to increased
granularity of the outer timer wheels which are far away from base:;clock.
But there is a worse problem than that. The following sequence of events
illustrates it:
- CPU0 timer1 is queued expires = 59969 and base->clk = 59131.
The timer is queued at wheel level 2, with resulting expiry time = 60032
(due to level granularity).
- CPU1 enters idle @60007, with next timer expiry @60020.
- CPU0 is hotplugged at @60009
- CPU1 exits idle and runs the control thread which migrates the
timers from CPU0
timer1 is now queued in level 0 for immediate handling in the next
softirq because the requested expiry time 59969 is before CPU1 base->clk
60007
- CPU1 runs code which forwards the base clock which succeeds because the
next expiring timer. which was collected at idle entry time is still set
to 60020.
So it forwards beyond 60007 and therefore misses to expire the migrated
timer1. That timer gets expired when the wheel wraps around again, which
takes between 63 and 630ms depending on the HZ setting.
Address both problems by invoking forward_timer_base() for the control CPUs
timer base. All other places, which might run into a similar problem
(mod_timer()/add_timer_on()) already invoke forward_timer_base() to avoid
that.
[ tglx: Massaged comment and changelog ]
Fixes: a683f390b9 ("timers: Forward the wheel clock whenever possible")
Co-developed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Lingutla Chandrasekhar <clingutla@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180118115022.6368-1-clingutla@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71db96ddfa upstream.
We've added a quirk to enable the recent Lenovo dock support, where it
overwrites the pin configs of NID 0x17 and 19, not only updating the
pin config cache. It works right after the boot, but the problem is
that the pin configs are occasionally cleared when the machine goes to
PM. Meanwhile the quirk writes the pin configs only at the pre-probe,
so this won't be applied any longer.
For addressing that issue, this patch moves the code to overwrite the
pin configs into HDA_FIXUP_ACT_INIT section so that it's always
applied at both probe and resume time.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195161
Fixes: 61fcf8ece9 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ba8f9d308 upstream.
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee70bc1e7b upstream.
tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.
This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b3a13173f upstream.
The buffers used as tx_buf/rx_buf in a SPI transfer need to be DMA-safe.
This cannot be guaranteed for the buffers passed to tpm_tis_spi_read_bytes
and tpm_tis_spi_write_bytes. Therefore, we need to use our own DMA-safe
buffer and copy the data to/from it.
The buffer needs to be allocated separately, to ensure that it is
cacheline-aligned and not shared with other data, so that DMA can work
correctly.
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c37fbc09bd upstream.
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d4d9b5a5 upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b8cb28d7c upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d24cd186d upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebabcf17bc upstream.
GCC7 is a bit too eager to generate suboptimal __multi3 calls (128bit
multiply with 128bit result) for MIPS64r6 builds, even in code which
doesn't explicitly use 128bit types, such as the following:
unsigned long func(unsigned long a, unsigned long b)
{
return a > (~0UL) / b;
}
Which GCC rearanges to:
return (unsigned __int128)a * (unsigned __int128)b > 0xffffffffffffffff;
Therefore implement __multi3, but only for MIPS64r6 with GCC7 as under
normal circumstances we wouldn't expect any calls to __multi3 to be
generated from kernel code.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: Matthew Fortune <matthew.fortune@mips.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17890/
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 45ee9d5e97 ("KVM: arm/arm64: Check pagesize when allocating a
hugepage at Stage 2") lost the check for PMD_SIZE during the backport
to 4.9.
Fix this by correcting the condition to detect hugepages during stage
2 allocation.
Fixes: 45ee9d5e97 ("KVM: arm/arm64: Check pagesize when allocating a hugepage at Stage 2")
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11d827a993 ]
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c76f97c99a ]
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf2acf66ad ]
When cleaning up after a partially successful gntdev_mmap(), unmap the
successfully mapped grant pages otherwise Xen will kill the domain if
in debug mode (Attempt to implicitly unmap a granted PTE) or Linux will
kill the process and emit "BUG: Bad page map in process" if Xen is in
release mode.
This is only needed when use_ptemod is true because gntdev_put_map()
will unmap grant pages itself when use_ptemod is false.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 195e2addbc ]
The 'sh_eth' driver's probe() method would fail on the SolutionEngine7710
board and crash on SolutionEngine7712 board as the platform code is
hopelessly behind the driver's platform data -- it passes the PHY address
instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in
order to fix the bug...
Fixes: 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56c0290202 ]
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9f ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b707fda2df ]
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78f3000493 ]
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13454c1455 ]
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 736a80bbfd ]
If there are multiple mesh stations with the same MAC address,
they will both get confused and start throwing warnings.
Obviously in this case nothing can actually work anyway, so just
drop frames that look like they're from ourselves early on.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
