[ Upstream commit aa86602a483ba48f51044fbaefa1ebbf6da194a4 ]
Move the configuration of the Auto-Hibern8 (AHIT) timer from the
post-link stage to the 'fixup_dev_quirks' function. This change allows
setting the AHIT based on the vendor requirements:
(a) Samsung: 3.5 ms
(b) Micron: 2 ms
(c) Others: 1 ms
Additionally, the clock gating timer is adjusted based on the AHIT
scale, with a maximum setting of 10 ms. This ensures that the clock
gating delay is appropriately configured to match the AHIT settings.
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20250811131423.3444014-3-peter.wang@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d05b24429e1de7a17c8fdccb04a04dbc8ad297b ]
If a backup port is configured for a bridge port, the bridge will
redirect known unicast traffic towards the backup port when the primary
port is administratively up but without a carrier. This is useful, for
example, in MLAG configurations where a system is connected to two
switches and there is a peer link between both switches. The peer link
serves as the backup port in case one of the switches loses its
connection to the multi-homed system.
In order to avoid flooding when the primary port loses its carrier, the
bridge does not flush dynamic FDB entries pointing to the port upon STP
disablement, if the port has a backup port.
The above means that known unicast traffic destined to the primary port
will be blackholed when the port is put administratively down, until the
FDB entries pointing to it are aged-out.
Given that the current behavior is quite weird and unlikely to be
depended on by anyone, amend the bridge to redirect to the backup port
also when the primary port is administratively down and not only when it
does not have a carrier.
The change is motivated by a report from a user who expected traffic to
be redirected to the backup port when the primary port was put
administratively down while debugging a network issue.
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250812080213.325298-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d03847175e81e86d4865456c15638faaf7c0634 ]
The thunderbolt driver sets up device link dependencies from hotplug ports
to the Host Router (aka Native Host Interface, NHI). When resuming from
system sleep, this allows the Host Router to re-establish tunnels to
attached Thunderbolt devices before the hotplug ports resume.
To identify the hotplug ports, the driver utilizes the is_hotplug_bridge
flag which also encompasses ACPI slots handled by the ACPI hotplug driver.
Thunderbolt hotplug ports are always Hot-Plug Capable PCIe ports, so it is
more apt to identify them with the is_pciehp flag.
Similarly, hotplug ports on older Thunderbolt controllers have broken MSI
support and are quirked to use legacy INTx interrupts instead. The quirk
identifies them with is_hotplug_bridge, even though all affected ports are
also matched by is_pciehp. So use is_pciehp here as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66ceb45b7d7e9673254116eefe5b6d3a44eba267 ]
In the past %pK was preferable to %p as it would not leak raw pointer
values into the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
Furthermore, restricted pointers ("%pK") were never meant to be used
through printk(). They can still unintentionally leak raw pointers or
acquire sleeping locks in atomic contexts.
Switch to the regular pointer formatting which is safer and
easier to reason about.
There are still a few users of %pK left, but these use it through seq_file,
for which its usage is safe.
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Acked-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250811-restricted-pointers-net-v5-1-2e2fdc7d3f2c@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d240b124cc9df62ccccee6054bc3d1d19018758 ]
Both ACPI and DT-based systems are required to obtain the external
camera sensor clock using the new devm_v4l2_sensor_clk_get() helper
function.
Ensure a dependency on HAVE_CLK when config VIDEO_CAMERA_SENSOR is
enabled.
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eea4f89b6461294ed6bea1d3285bb3f79c09a041 ]
The driver tries to calculate the value for REG_WAKEUP_TIME. However,
the calculation itself is not correct, and to add on it, the resulting
value is almost always larger than the field's size, so the actual
result is more or less random.
According to the docs, figuring out the value for REG_WAKEUP_TIME
requires HW characterization and there's no way to have a generic
algorithm to come up with the value. That doesn't help at all...
However, we know that the value must be smaller than the line time, and,
at least in my understanding, the proper value for it is quite small.
Testing shows that setting it to 1/10 of the line time seems to work
well. All video modes from my HDMI monitor work with this algorithm.
Hopefully we'll get more information on how to calculate the value, and
we can then update this.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-11-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19fb9c5b815f70eb90d5b545f65b83bc9c490ecd ]
The v4l2_fh initialized and added in vpu_v4l2_open() is delete and
cleaned up when the last reference to the vpu_inst is released. This may
happen later than at vpu_v4l2_close() time.
Not deleting and cleaning up the v4l2_fh when closing the file handle to
the video device is not ideal, as the v4l2_fh will still be present in
the video device's fh_list, and will store a copy of events queued to
the video device. There may also be other side effects of keeping alive
an object that represents an open file handle after the file handle is
closed.
The v4l2_fh instance is embedded in the vpu_inst structure, and is
accessed in two different ways:
- in vpu_notify_eos() and vpu_notify_source_change(), to queue V4L2
events to the file handle ; and
- through the driver to access the v4l2_fh.m2m_ctx pointer.
The v4l2_fh.m2m_ctx pointer is not touched by v4l2_fh_del() and
v4l2_fh_exit(). It is set to NULL by the driver when closing the file
handle, in vpu_v4l2_close().
The vpu_notify_eos() and vpu_notify_source_change() functions are called
in vpu_set_last_buffer_dequeued() and vdec_handle_resolution_change()
respectively, only if the v4l2_fh.m2m_ctx pointer is not NULL. There is
therefore a guarantee that no new event will be queued to the v4l2_fh
after vpu_v4l2_close() destroys the m2m_ctx.
The vpu_notify_eos() function is also called from vpu_vb2_buf_finish(),
which is guaranteed to be called for all queued buffers when
vpu_v4l2_close() calls v4l2_m2m_ctx_release(), and will not be called
later.
It is therefore safe to assume that the driver will not touch the
v4l2_fh, except to check the m2m_ctx pointer, after vpu_v4l2_close()
destroys the m2m_ctx. We can safely delete and cleanup the v4l2_fh
synchronously in vpu_v4l2_close().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ming Qian <ming.qian@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc6e8d1ccea792d8550428e0831e3a35b0ccfddc ]
The ivtv driver has a structure named ivtv_open_id that models an open
file handle for the device. It embeds a v4l2_fh instance for file
handles that correspond to a V4L2 video device, and stores a pointer to
that v4l2_fh in struct ivtv_stream to identify which open file handle
owns a particular stream.
In addition to video devices, streams can be owned by ALSA PCM devices.
Those devices do not make use of the v4l2_fh instance for obvious
reasons, but the snd_ivtv_pcm_capture_open() function still initializes
a "fake" v4l2_fh for the sole purpose of using it as an open file handle
identifier. The v4l2_fh is not properly destroyed when the ALSA PCM
device is closed, leading to possible resource leaks.
Fortunately, the v4l2_fh instance pointed to by ivtv_stream is not
accessed, only the pointer value is used for comparison. Replace it with
a pointer to the ivtv_open_id structure that embeds the v4l2_fh, and
don't initialize the v4l2_fh for ALSA PCM devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57af162bfc8c05332a28c4d458d246cc46d2746d ]
Some kfd ioctls may not be available depending on the kernel version the
user is running, as such we need to report -ENOTTY so userland can
determine the cause of the ioctl failure.
Signed-off-by: Geoffrey McRae <geoffrey.mcrae@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc4c0a48bdad7f225740b8e750fdc1da6d85e1eb ]
The get_next_frame() function in psock_tpacket.c was missing a return
statement in its default switch case, leading to a compiler warning.
This was caused by a `bug_on(1)` call, which is defined as an
`assert()`, being compiled out because NDEBUG is defined during the
build.
Instead of adding a `return NULL;` which would silently hide the error
and could lead to crashes later, this change restores the original
author's intent. By adding `#undef NDEBUG` before including <assert.h>,
we ensure the assertion is active and will cause the test to abort if
this unreachable code is ever executed.
Signed-off-by: Wake Liu <wakel@google.com>
Link: https://patch.msgid.link/20250809062013.2407822-1-wakel@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c36748e8733ef9c5f4cd1d7c4327994e5b88b8df ]
The `__WORDSIZE` macro, defined in the non-standard `<bits/wordsize.h>`
header, is a GNU extension and not universally available with all
toolchains, such as Clang when used with musl libc.
This can lead to build failures in environments where this header is
missing.
The intention of the code is to determine the bit width of a C `long`.
Replace the non-portable `__WORDSIZE` with the standard and portable
`sizeof(long) * 8` expression to achieve the same result.
This change also removes the inclusion of the now-unused
`<bits/wordsize.h>` header.
Signed-off-by: Wake Liu <wakel@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc7086b39e5e4f3d3ca82caaea20538c9b62d42 ]
RDC PCI to PCIe bridges, present on Vortex86DX3 and Vortex86EX2 SoCs, do
not support MSIs. If enabled, interrupts generated by PCIe devices never
reach the processor.
I have contacted the manufacturer (DM&P) and they confirmed that PCI MSIs
need to be disabled for them.
Signed-off-by: Marcos Del Sol Vives <marcos@orca.pet>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250705233209.721507-1-marcos@orca.pet
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6510b62fe9303aaf48ff136ff69186bcfc32172d ]
snprintf() returns the number of characters that *would* have been
written, which can overestimate how much you actually wrote to the
buffer in case of truncation. That leads to 'data += this' advancing
the pointer past the end of the buffer and size going negative.
Switching to scnprintf() prevents potential buffer overflows and ensures
consistent behavior when building the output string.
Signed-off-by: Seyediman Seyedarab <ImanDevel@gmail.com>
Link: https://lore.kernel.org/r/20250724195913.60742-1-ImanDevel@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e7581eda8c76d1ca4cf519631a4d4eb9f82b94c ]
Acquire jpeg_pg_lock before changes to jpeg power state
and release it after power off from idle work handler.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3b1ccf83be83a3330e38194ddfd1a91fec69be ]
Cached metrics data validity is 1ms on arcturus. It's not reasonable for
any client to query gpu_metrics at a faster rate and constantly
interrupt PMFW.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e87577ef6daa0cfb10ca139c720f0c57bd894174 ]
Cached metrics data validity is 1ms on aldebaran. It's not reasonable
for any client to query gpu_metrics at a faster rate and constantly
interrupt PMFW.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e72fdba8a32ce062a86571edff4592710c26215 ]
[Why]
The reason some high-resolution monitors fail to display properly
is that this platform does not support sufficiently high DPP and
DISP clock frequencies
[How]
Update DISP and DPP clocks from the smu clock table then DML can
filter these mode if not support.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf06bd4cf2512d564fdb451b07de0cebe7b138d ]
Add PCI IDs to support display probe for cyan skillfish
family of SOCs.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3419e1e44b87d4176fb98679a77301b1ca40f63 ]
[WHY]
In the worst case, AUX intra-hop done can take hundreds of milliseconds as
each retimer in a link might have to wait a full AUX_RD_INTERVAL to send
LT abort downstream.
[HOW]
Wait 300ms for each retimer in a link to allow time to propagate a LT abort
without infinitely waiting on intra-hop done.
For no-retimer case, keep the max duration at 10ms.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca74cc428f2b9d0170c56b473dbcfd7fa01daf2d ]
[Why]
When transitioning between topologies such as multi-display to single
display ODM 2:1, pipes might not be freed before use.
[How]
In dc_commit_streams, commit an additional, minimal transition if
original transition is not seamless to ensure pipes are freed.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ac4890ac39352ccea132109e32911495574c3ec ]
We observed the initial probe of the da9063 failing in
da9063_get_device_type in about 30% of boots on a Xilinx ZynqMP based
board. The problem originates in da9063_i2c_blockreg_read, which uses
a single bus transaction to turn the register page and then read a
register. On the bus, this should translate to a write to register 0,
followed by a read to the target register, separated by a repeated
start. However, we found that after the write to register 0, the
controller sometimes continues directly with the register address of
the read request, without sending the chip address or a repeated start
in between, which makes the read request invalid.
To fix this, separate turning the page and reading the register into
two separate transactions. This brings the initialization code in line
with the rest of the driver, which uses register maps (which to my
knowledge do not use repeated starts after turning the page). This has
been included in our kernel for several months and was recently
included in a shipped product. For us, it reliably fixes the issue,
and we have not observed any new issues.
While the underlying problem is probably with the i2c controller or
its driver, I still propose a change here in the interest of
robustness: First, I'm not sure this issue can be fixed on the
controller side, since there are other issues related to repeated
start which can't (AR# 60695, AR# 61664). Second, similar problems
might exist with other controllers.
Signed-off-by: Jens Kehne <jens.kehne@agilent.com>
Link: https://lore.kernel.org/r/20250804133754.3496718-1-jens.kehne@agilent.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 364752aa0c6ab0a06a2d5bfdb362c1ca407f1a30 ]
clang-21 warns about one uninitialized variable getting dereferenced
in madera_dev_init:
drivers/mfd/madera-core.c:739:10: error: variable 'mfd_devs' is uninitialized when used here [-Werror,-Wuninitialized]
739 | mfd_devs, n_devs,
| ^~~~~~~~
drivers/mfd/madera-core.c:459:33: note: initialize the variable 'mfd_devs' to silence this warning
459 | const struct mfd_cell *mfd_devs;
| ^
| = NULL
The code is actually correct here because n_devs is only nonzero
when mfd_devs is a valid pointer, but this is impossible for the
compiler to see reliably.
Change the logic to check for the pointer as well, to make this easier
for the compiler to follow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250807071932.4085458-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2734fdbc9bb8a3aeb309ba0d62212d7f53f30bc7 ]
When we are successful in using cpufreq min/max limits,
skip setting the raw MSR limits entirely.
This is necessary to avoid undoing any modification that
the cpufreq driver makes to our sysfs request.
eg. intel_pstate may take our request for a limit
that is valid according to HWP.CAP.MIN/MAX and clip
it to be within the range available in PLATFORM_INFO.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c97c057d357c4b39b153e9e430bbf8976e05bd4e ]
On enabling HWP, preserve the reserved bits in MSR_PM_ENABLE.
Also, skip writing the MSR_PM_ENABLE if HWP is already enabled.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62127655b7ab7b8c2997041aca48a81bf5c6da0c ]
The fopen_or_die() function was previously hardcoded
to open files in read-only mode ("r"), ignoring the
mode parameter passed to it. This patch corrects
fopen_or_die() to use the provided mode argument,
allowing for flexible file access as intended.
Additionally, the call to fopen_or_die() in
err_on_hypervisor() incorrectly used the mode
"ro", which is not a valid fopen mode. This is
fixed to use the correct "r" mode.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23199d2aa6dcaf6dd2da772f93d2c94317d71459 ]
Fix incorrect size parameter passed to cpuidle_state_write_file() in
cpuidle_state_disable().
The function was incorrectly using sizeof(disable) which returns the
size of the unsigned int variable (4 bytes) instead of the actual
length of the string stored in the 'value' buffer.
Since 'value' is populated with snprintf() to contain the string
representation of the disable value, we should use the length
returned by snprintf() to get the correct string length for
writing to the sysfs file.
This ensures the correct number of bytes is written to the cpuidle
state disable file in sysfs.
Link: https://lore.kernel.org/r/20250917050820.1785377-1-kaushlendra.kumar@intel.com
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4363264111e1297fa37aa39b0598faa19298ecca ]
If uprobe handler changes instruction pointer we still execute single
step) or emulate the original instruction and increment the (new) ip
with its length.
This makes the new instruction pointer bogus and application will
likely crash on illegal instruction execution.
If user decided to take execution elsewhere, it makes little sense
to execute the original instruction, so let's skip it.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20250916215301.664963-3-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e482655019ab6fcfe8865b62432c6d03f0b5f80 ]
The NVMe Base Specification 2.1 states that:
"""
A host requests an explicit persistent connection ... by specifying a
non-zero Keep Alive Timer value in the Connect command.
"""
As such if we are starting a persistent connection to a discovery
controller and the KATO is currently 0 we need to update KATO to a non
zero value to avoid continuous timeouts on the target.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f12d1137c2382c80aada8e05d7cc650cd4e403c ]
It is possible for bpf_xdp_adjust_tail() to free all fragments. The
kfunc currently clears the XDP_FLAGS_HAS_FRAGS bit, but not
XDP_FLAGS_FRAGS_PF_MEMALLOC. So far, this has not caused a issue when
building sk_buff from xdp_buff since all readers of xdp_buff->flags
use the flag only when there are fragments. Clear the
XDP_FLAGS_FRAGS_PF_MEMALLOC bit as well to make the flags correct.
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://patch.msgid.link/20250922233356.3356453-2-ameryhung@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0bf7cd5df18466d969bb60e8890b74cf96081ca ]
In the __arch_prepare_bpf_trampoline() function, retval_off is only
meaningful when save_ret is true, so the current logic is correct.
However, in the original logic, retval_off is only initialized under
certain conditions; for example, in the fmod_ret logic, the compiler is
not aware that the flags of the fmod_ret program (prog) have set
BPF_TRAMP_F_CALL_ORIG, which results in an uninitialized symbol
compilation warning.
So initialize retval_off unconditionally to fix it.
Signed-off-by: Chenghao Duan <duanchenghao@kylinos.cn>
Reviewed-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/r/20250922062244.822937-2-duanchenghao@kylinos.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d726c4dbeeddef612e6bed27edd29733f4d13af ]
Following deadlock can be triggered easily by lockdep:
WARNING: possible circular locking dependency detected
6.17.0-rc3-00124-ga12c2658ced0 #1665 Not tainted
------------------------------------------------------
check/1334 is trying to acquire lock:
ff1100011d9d0678 (&q->sysfs_lock){+.+.}-{4:4}, at: blk_unregister_queue+0x53/0x180
but task is already holding lock:
ff1100011d9d00e0 (&q->q_usage_counter(queue)#3){++++}-{0:0}, at: del_gendisk+0xba/0x110
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&q->q_usage_counter(queue)#3){++++}-{0:0}:
blk_queue_enter+0x40b/0x470
blkg_conf_prep+0x7b/0x3c0
tg_set_limit+0x10a/0x3e0
cgroup_file_write+0xc6/0x420
kernfs_fop_write_iter+0x189/0x280
vfs_write+0x256/0x490
ksys_write+0x83/0x190
__x64_sys_write+0x21/0x30
x64_sys_call+0x4608/0x4630
do_syscall_64+0xdb/0x6b0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
-> #1 (&q->rq_qos_mutex){+.+.}-{4:4}:
__mutex_lock+0xd8/0xf50
mutex_lock_nested+0x2b/0x40
wbt_init+0x17e/0x280
wbt_enable_default+0xe9/0x140
blk_register_queue+0x1da/0x2e0
__add_disk+0x38c/0x5d0
add_disk_fwnode+0x89/0x250
device_add_disk+0x18/0x30
virtblk_probe+0x13a3/0x1800
virtio_dev_probe+0x389/0x610
really_probe+0x136/0x620
__driver_probe_device+0xb3/0x230
driver_probe_device+0x2f/0xe0
__driver_attach+0x158/0x250
bus_for_each_dev+0xa9/0x130
driver_attach+0x26/0x40
bus_add_driver+0x178/0x3d0
driver_register+0x7d/0x1c0
__register_virtio_driver+0x2c/0x60
virtio_blk_init+0x6f/0xe0
do_one_initcall+0x94/0x540
kernel_init_freeable+0x56a/0x7b0
kernel_init+0x2b/0x270
ret_from_fork+0x268/0x4c0
ret_from_fork_asm+0x1a/0x30
-> #0 (&q->sysfs_lock){+.+.}-{4:4}:
__lock_acquire+0x1835/0x2940
lock_acquire+0xf9/0x450
__mutex_lock+0xd8/0xf50
mutex_lock_nested+0x2b/0x40
blk_unregister_queue+0x53/0x180
__del_gendisk+0x226/0x690
del_gendisk+0xba/0x110
sd_remove+0x49/0xb0 [sd_mod]
device_remove+0x87/0xb0
device_release_driver_internal+0x11e/0x230
device_release_driver+0x1a/0x30
bus_remove_device+0x14d/0x220
device_del+0x1e1/0x5a0
__scsi_remove_device+0x1ff/0x2f0
scsi_remove_device+0x37/0x60
sdev_store_delete+0x77/0x100
dev_attr_store+0x1f/0x40
sysfs_kf_write+0x65/0x90
kernfs_fop_write_iter+0x189/0x280
vfs_write+0x256/0x490
ksys_write+0x83/0x190
__x64_sys_write+0x21/0x30
x64_sys_call+0x4608/0x4630
do_syscall_64+0xdb/0x6b0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
other info that might help us debug this:
Chain exists of:
&q->sysfs_lock --> &q->rq_qos_mutex --> &q->q_usage_counter(queue)#3
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&q->q_usage_counter(queue)#3);
lock(&q->rq_qos_mutex);
lock(&q->q_usage_counter(queue)#3);
lock(&q->sysfs_lock);
Root cause is that queue_usage_counter is grabbed with rq_qos_mutex
held in blkg_conf_prep(), while queue should be freezed before
rq_qos_mutex from other context.
The blk_queue_enter() from blkg_conf_prep() is used to protect against
policy deactivation, which is already protected with blkcg_mutex, hence
convert blk_queue_enter() to blkcg_mutex to fix this problem. Meanwhile,
consider that blkcg_mutex is held after queue is freezed from policy
deactivation, also convert blkg_alloc() to use GFP_NOIO.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b54082c3ed4dc9821cdf0edb17302355cc5bb45 ]
sys_get_robust_list() and compat_get_robust_list() use ptrace_may_access()
to check if the calling task is allowed to access another task's
robust_list pointer. This check is racy against a concurrent exec() in the
target process.
During exec(), a task may transition from a non-privileged binary to a
privileged one (e.g., setuid binary) and its credentials/memory mappings
may change. If get_robust_list() performs ptrace_may_access() before
this transition, it may erroneously allow access to sensitive information
after the target becomes privileged.
A racy access allows an attacker to exploit a window during which
ptrace_may_access() passes before a target process transitions to a
privileged state via exec().
For example, consider a non-privileged task T that is about to execute a
setuid-root binary. An attacker task A calls get_robust_list(T) while T
is still unprivileged. Since ptrace_may_access() checks permissions
based on current credentials, it succeeds. However, if T begins exec
immediately afterwards, it becomes privileged and may change its memory
mappings. Because get_robust_list() proceeds to access T->robust_list
without synchronizing with exec() it may read user-space pointers from a
now-privileged process.
This violates the intended post-exec access restrictions and could
expose sensitive memory addresses or be used as a primitive in a larger
exploit chain. Consequently, the race can lead to unauthorized
disclosure of information across privilege boundaries and poses a
potential security risk.
Take a read lock on signal->exec_update_lock prior to invoking
ptrace_may_access() and accessing the robust_list/compat_robust_list.
This ensures that the target task's exec state remains stable during the
check, allowing for consistent and synchronized validation of
credentials.
Suggested-by: Jann Horn <jann@thejh.net>
Signed-off-by: Pranav Tyagi <pranav.tyagi03@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/linux-fsdevel/1477863998-3298-5-git-send-email-jann@thejh.net/
Link: https://github.com/KSPP/linux/issues/119
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b1b7961170e4fcad488755e5ffaaaf9bd527e8f ]
Refuse to register a cpuidle device if the given CPU has a cpuidle
device already and print a message regarding it.
Without this, an attempt to register a new cpuidle device without
unregistering the existing one leads to the removal of the existing
cpuidle device without removing its sysfs interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5612ea8b554375d45c14cbb0f8ea93ec5d172891 ]
This fixes the build with -Werror -Wall.
btf_dumper.c:71:31: error: variable 'finfo' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
71 | info.func_info = ptr_to_u64(&finfo);
| ^~~~~
prog.c:2294:31: error: variable 'func_info' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
2294 | info.func_info = ptr_to_u64(&func_info);
|
v2:
- Initialize instead of using memset.
Signed-off-by: Tom Stellard <tstellar@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Quentin Monnet <qmo@kernel.org>
Link: https://lore.kernel.org/bpf/20250917183847.318163-1-tstellar@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41307ec7df057239aae3d0f089cc35a0d735cdf8 ]
The X1E80100 battery management firmware sends a notification with
code 0x83 when the battery charging state changes, such as switching
between fast charge, taper charge, end of charge, or any other error
charging states.
The same notification code is used with bit[8] set when charging stops
because the charge control end threshold is reached. Additionally,
a 2-bit value is included in bit[10:9] with the same code to indicate
the charging source capability, which is determined by the calculated
power from voltage and current readings from PDOs: 2 means a strong
charger over 60W, 1 indicates a weak charger, and 0 means there is no
charging source.
These 3-MSB [10:8] in the notification code is not much useful for now,
hence just ignore them and trigger a power supply change event whenever
0x83 notification code is received. This helps to eliminate the unknown
notification error messages.
Reported-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Closes: https://lore.kernel.org/all/r65idyc4of5obo6untebw4iqfj2zteiggnnzabrqtlcinvtddx@xc4aig5abesu/
Signed-off-by: Fenglin Wu <fenglin.wu@oss.qualcomm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
