commit 147186f531 upstream.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21e35e898a upstream.
For data read commands, SDHC may initiate data transfers even before it
completely process the command response. In case command itself fails,
driver un-maps the memory associated with data transfer but this memory
can still be accessed by SDHC for the already initiated data transfer.
This scenario can lead to un-mapped memory access error.
To avoid this scenario, reset SDHC (when command fails) prior to
un-mapping memory. Resetting SDHC ensures that all in-flight data
transfers are either aborted or completed. So we don't run into this
scenario.
Swap the reset, un-map steps sequence in sdhci_request_done().
Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Pradeep P V K <pragalla@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46094049a4 upstream.
This reverts commit 04b8edad26.
mx25l51245g and mx66l51235l have the same flash ID. The flash
detection returns the first entry in the flash_info array that
matches the flash ID that was read, thus for the 0xc2201a ID,
mx25l51245g was always hit, introducing a regression for
mx66l51235l.
If one wants to differentiate the flash names, a better fix would be
to differentiate between the two at run-time, depending on SFDP,
and choose the correct name from a list of flash names, depending on
the SFDP differentiator.
Fixes: 04b8edad26 ("mtd: spi-nor: macronix: Add support for mx25l51245g")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210402082031.19055-2-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fab29e356 upstream.
Commit 339ddb53d3 ("fs/epoll: remove unnecessary wakeups of nested
epoll") changed the userspace visible behavior of exclusive waiters
blocked on a common epoll descriptor upon a single event becoming ready.
Previously, all tasks doing epoll_wait would awake, and now only one is
awoken, potentially causing missed wakeups on applications that rely on
this behavior, such as Apache Qpid.
While the aforementioned commit aims at having only a wakeup single path
in ep_poll_callback (with the exceptions of epoll_ctl cases), we need to
restore the wakeup in what was the old ep_scan_ready_list() such that
the next thread can be awoken, in a cascading style, after the waker's
corresponding ep_send_events().
Link: https://lkml.kernel.org/r/20210405231025.33829-3-dave@stgolabs.net
Fixes: 339ddb53d3 ("fs/epoll: remove unnecessary wakeups of nested epoll")
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Roman Penyaev <rpenyaev@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9046625511 upstream.
When mounting eCryptfs, a null "dev_name" argument to ecryptfs_mount()
causes a kernel panic if the parsed options are valid. The easiest way to
reproduce this is to call mount() from userspace with an existing
eCryptfs mount's options and a "source" argument of 0.
Error out if "dev_name" is null in ecryptfs_mount()
Fixes: 237fead619 ("[PATCH] ecryptfs: fs/Makefile and fs/Kconfig")
Cc: stable@vger.kernel.org
Signed-off-by: Jeffrey Mitchell <jeffrey.mitchell@starlab.io>
Signed-off-by: Tyler Hicks <code@tyhicks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c9af478c0 upstream.
# echo switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter
will cause switch_mm to stop tracing by the traceoff command.
# echo -n switch_mm:traceoff > /sys/kernel/tracing/set_ftrace_filter
does nothing.
The reason is that the parsing in the write function only processes
commands if it finished parsing (there is white space written after the
command). That's to handle:
write(fd, "switch_mm:", 10);
write(fd, "traceoff", 8);
cases, where the command is broken over multiple writes.
The problem is if the file descriptor is closed, then the write call is
not processed, and the command needs to be processed in the release code.
The release code can handle matching of functions, but does not handle
commands.
Cc: stable@vger.kernel.org
Fixes: eda1e32855 ("tracing: handle broken names in ftrace filter")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cfd895643 upstream.
In cm_write(), if the 'buf' is allocated memory but not fully consumed,
it is possible to reallocate the buffer without freeing it by passing
'*ppos' as 0 on a subsequent call.
Add an explicit kfree() before kzalloc() to prevent the possible memory
leak.
Fixes: 526b4af47f ("ACPI: Split out custom_method functionality into an own driver")
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e483bb9a99 upstream.
In cm_write(), buf is always freed when reaching the end of the
function. If the requested count is less than table.length, the
allocated buffer will be freed but subsequent calls to cm_write() will
still try to access it.
Remove the unconditional kfree(buf) at the end of the function and
set the buf to NULL in the -EINVAL error path to match the rest of
function.
Fixes: 03d1571d95 ("ACPI: custom_method: fix memory leaks")
Signed-off-by: Mark Langsdorf <mlangsdo@redhat.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dcd15665a upstream.
Check the eventlog signature before using it. This avoids using an
empty log, as may be the case when QEMU created the ACPI tables,
rather than probing the EFI log next. This resolves an issue where
the EFI log was empty since an empty ACPI log was used.
Cc: stable@vger.kernel.org
Fixes: 85467f63a0 ("tpm: Add support for event log pointer found in TPM2 ACPI table")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a3e0fad16 upstream.
The virtqueue doorbell is usually implemented via registeres but we
don't provide the necessary vma->flags like VM_PFNMAP. This may cause
several issues e.g when userspace tries to map the doorbell via vhost
IOTLB, kernel may panic due to the page is not backed by page
structure. This patch fixes this by setting the necessary
vm_flags. With this patch, try to map doorbell via IOTLB will fail
with bad address.
Cc: stable@vger.kernel.org
Fixes: ddd89d0a05 ("vhost_vdpa: support doorbell mapping via mmap")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20210413091557.29008-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70fac8088c upstream.
Tests with kvm and a kmemdebug kernel showed, that on hot unplug the
zcard and zqueue structs for the unplugged card or queue are not
properly freed because of a mismatch with get/put for the embedded
kref counter.
This fix now adjusts the handling of the kref counters. With init the
kref counter starts with 1. This initial value needs to drop to zero
with the unregister of the card or queue to trigger the release and
free the object.
Fixes: 29c2680fd2 ("s390/ap: fix ap devices reference counting")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b1ae24827 upstream.
Query like 'file tcp_input.c line 1234 +p' was broken by
commit aaebe329bf ("dyndbg: accept 'file foo.c:func1' and 'file
foo.c:10-100'") because a file name without a ':' now makes the loop in
ddebug_parse_query() exits early before parsing the 'line 1234' part.
As a result, all pr_debug() in tcp_input.c will be enabled, instead of only
the one on line 1234. Changing 'break' to 'continue' fixes this.
Fixes: aaebe329bf ("dyndbg: accept 'file foo.c:func1' and 'file foo.c:10-100'")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Shuo Chen <shuochen@google.com>
Acked-by: Jason Baron <jbaron@akamai.com>
Link: https://lore.kernel.org/r/20210414212400.2927281-1-giantchen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1ce3986ba upstream.
A failing usercopy of the slot uid will lead to a stale entry in the
file descriptor table as put_unused_fd() won't release it. This enables
userland to refer to a dangling 'file' object through that still valid
file descriptor, leading to all kinds of use-after-free exploitation
scenarios.
Exchanging put_unused_fd() for close_fd(), ksys_close() or alike won't
solve the underlying issue, as the file descriptor might have been
replaced in the meantime, e.g. via userland calling close() on it
(leading to a NULL pointer dereference in the error handling code as
'fget(enclave_fd)' will return a NULL pointer) or by dup2()'ing a
completely different file object to that very file descriptor, leading
to the same situation: a dangling file descriptor pointing to a freed
object -- just in this case to a file object of user's choosing.
Generally speaking, after the call to fd_install() the file descriptor
is live and userland is free to do whatever with it. We cannot rely on
it to still refer to our enclave object afterwards. In fact, by abusing
userfaultfd() userland can hit the condition without any racing and
abuse the error handling in the nitro code as it pleases.
To fix the above issues, defer the call to fd_install() until all
possible errors are handled. In this case it's just the usercopy, so do
it directly in ne_create_vm_ioctl() itself.
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Andra Paraschiv <andraprs@amazon.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210429165941.27020-2-andraprs@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec32332df7 upstream.
When parsing the structures in the shared memory, there are values which
come from the remote device. For example, a transfer completion event
will have a pointer to the tre in the relevant channel's transfer ring.
As another example, event ring elements may specify a channel in which
the event occurred, however the specified channel value may not be valid
as no channel is defined at that index even though the index may be less
than the maximum allowed index. Such values should be considered to be
untrusted, and validated before use. If we blindly use such values, we
may access invalid data or crash if the values are corrupted.
If validation fails, drop the relevant event.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Link: https://lore.kernel.org/r/1615411855-15053-1-git-send-email-jhugo@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2b12db535 upstream.
VFIO_IOMMU_TYPE1 does not compile with !MMU:
../drivers/vfio/vfio_iommu_type1.c: In function 'follow_fault_pfn':
../drivers/vfio/vfio_iommu_type1.c:536:22: error: implicit declaration of function 'pte_write'; did you mean 'vfs_write'? [-Werror=implicit-function-declaration]
So require it.
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <0-v1-02cb5500df6e+78-vfio_no_mmu_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ef1af4de upstream.
Currently, the lockdown state is queried unconditionally, even though
its result is used only if the PERF_SAMPLE_REGS_INTR bit is set in
attr.sample_type. While that doesn't matter in case of the Lockdown LSM,
it causes trouble with the SELinux's lockdown hook implementation.
SELinux implements the locked_down hook with a check whether the current
task's type has the corresponding "lockdown" class permission
("integrity" or "confidentiality") allowed in the policy. This means
that calling the hook when the access control decision would be ignored
generates a bogus permission check and audit record.
Fix this by checking sample_type first and only calling the hook when
its result would be honored.
Fixes: b0c8fdc7fd ("lockdown: Lock down perf when in confidentiality mode")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Link: https://lkml.kernel.org/r/20210224215628.192519-1-omosnace@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6759e18e5c upstream.
On recent Thinkpad platforms it was reported that temp sensor 11 was
always incorrectly displaying 66C. It turns out the reason for this is
that this location in EC RAM is not a temperature sensor but is the
power supply ID (offset 0xC2).
Based on feedback from the Lenovo firmware team the EC RAM version can
be determined and for the current version (3) only the 0x78 to 0x7F
range is used for temp sensors. I don't have any details for earlier
versions so I have left the implementation unaltered there.
Note - in this block only 0x78 and 0x79 are officially designated (CPU &
GPU sensors). The use of the other locations in the block will vary from
platform to platform; but the existing logic to detect a sensor presence
holds.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20210407212015.298222-1-markpearson@lenovo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca91fd8c76 upstream.
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 708fa01597 upstream.
Commit 146d62e5a5 ("ovl: detect overlapping layers") made sure we don't
have overlapping layers, but it also broke the arguably valid use case of
mount -olowerdir=/,upperdir=/subdir,..
where upperdir overlaps lowerdir on the same filesystem. This has been
causing regressions.
Revert the check, but only for the specific case where upperdir and/or
workdir are subdirectories of lowerdir. Any other overlap (e.g. lowerdir
is subdirectory of upperdir, etc) case is crazy, so leave the check in
place for those.
Overlaps are detected at lookup time too, so reverting the mount time check
should be safe.
Fixes: 146d62e5a5 ("ovl: detect overlapping layers")
Cc: <stable@vger.kernel.org> # v5.2
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaab1d45cd upstream.
Since commit 6815f479ca ("ovl: use only uppermetacopy state in
ovl_lookup()"), overlayfs doesn't put temporary dentry when there is a
metacopy error, which leads to dentry leaks when shutting down the related
superblock:
overlayfs: refusing to follow metacopy origin for (/file0)
...
BUG: Dentry (____ptrval____){i=3f33,n=file3} still in use (1) [unmount of overlay overlay]
...
WARNING: CPU: 1 PID: 432 at umount_check.cold+0x107/0x14d
CPU: 1 PID: 432 Comm: unmount-overlay Not tainted 5.12.0-rc5 #1
...
RIP: 0010:umount_check.cold+0x107/0x14d
...
Call Trace:
d_walk+0x28c/0x950
? dentry_lru_isolate+0x2b0/0x2b0
? __kasan_slab_free+0x12/0x20
do_one_tree+0x33/0x60
shrink_dcache_for_umount+0x78/0x1d0
generic_shutdown_super+0x70/0x440
kill_anon_super+0x3e/0x70
deactivate_locked_super+0xc4/0x160
deactivate_super+0xfa/0x140
cleanup_mnt+0x22e/0x370
__cleanup_mnt+0x1a/0x30
task_work_run+0x139/0x210
do_exit+0xb0c/0x2820
? __kasan_check_read+0x1d/0x30
? find_held_lock+0x35/0x160
? lock_release+0x1b6/0x660
? mm_update_next_owner+0xa20/0xa20
? reacquire_held_locks+0x3f0/0x3f0
? __sanitizer_cov_trace_const_cmp4+0x22/0x30
do_group_exit+0x135/0x380
__do_sys_exit_group.isra.0+0x20/0x20
__x64_sys_exit_group+0x3c/0x50
do_syscall_64+0x45/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xae
...
VFS: Busy inodes after unmount of overlay. Self-destruct in 5 seconds. Have a nice day...
This fix has been tested with a syzkaller reproducer.
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: <stable@vger.kernel.org> # v5.8+
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 6815f479ca ("ovl: use only uppermetacopy state in ovl_lookup()")
Signed-off-by: Mickaël Salaün <mic@linux.microsoft.com>
Link: https://lore.kernel.org/r/20210329164907.2133175-1-mic@digikod.net
Reviewed-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit: 3d2d861eb0
The PRP addressing scheme requires all PRP entries except for the
first one to have a zero offset into the NVMe controller pages (which
can be different from the Linux PAGE_SIZE). Use the min_align_mask
device parameter to ensure that swiotlb does not change the address
of the buffer modulo the device page size to ensure that the PRPs
won't be malformed.
Signed-off-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit: 1f221a0d0d
swiotlb: respect min_align_mask
Respect the min_align_mask in struct device_dma_parameters in swiotlb.
There are two parts to it:
1) for the lower bits of the alignment inside the io tlb slot, just
extent the size of the allocation and leave the start of the slot
empty
2) for the high bits ensure we find a slot that matches the high bits
of the alignment to avoid wasting too much memory
Based on an earlier patch from Jianxiong Gao <jxgao@google.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jianxiong Gao <jxgao@google.com>
Tested-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit: 16fc3cef33
swiotlb_tbl_map_single currently nevers sets a tlb_addr that is not
aligned to the tlb bucket size. But we're going to add such a case
soon, for which this adjustment would be bogus.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jianxiong Gao <jxgao@google.com>
Tested-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit: ca10d0f8e5
swiotlb: clean up swiotlb_tbl_unmap_single
Remove a layer of pointless indentation, replace a hard to follow
ternary expression with a plain if/else.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jianxiong Gao <jxgao@google.com>
Tested-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jianxiong Gao <jxgao@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
