commit f7eb147d30 upstream.
Invoke wiz_init() before configuring anything else in Sierra/Torrent
(invoked as part of of_platform_device_create()). wiz_init() resets the
SERDES device and any configuration done in the probe() of
Sierra/Torrent will be lost. In order to prevent SERDES configuration
from getting reset, invoke wiz_init() immediately before invoking
of_platform_device_create().
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Cc: <stable@vger.kernel.org> # v5.10
Link: https://lore.kernel.org/r/20210319124128.13308-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3641762c1c upstream.
Before this commit lis3lv02d_get_pwron_wait() had a WARN_ONCE() to catch
a potential divide by 0. WARN macros should only be used to catch internal
kernel bugs and that is not the case here. We have been receiving a lot of
bug reports about kernel backtraces caused by this WARN.
The div value being checked comes from the lis3->odrs[] array. Which
is sized to be a power-of-2 matching the number of bits in lis3->odr_mask.
The only lis3 model where this array is not entirely filled with non zero
values. IOW the only model where we can hit the div == 0 check is the
3dc ("8 bits 3DC sensor") model:
int lis3_3dc_rates[16] = {0, 1, 10, 25, 50, 100, 200, 400, 1600, 5000};
Note the 0 value at index 0, according to the datasheet an odr index of 0
means "Power-down mode". HP typically uses a lis3 accelerometer for HDD
fall protection. What I believe is happening here is that on newer
HP devices, which only contain a SDD, the BIOS is leaving the lis3 device
powered-down since it is not used for HDD fall protection.
Note that the lis3_3dc_rates array initializer only specifies 10 values,
which matches the datasheet. So it also contains 6 zero values at the end.
Replace the WARN with a normal check, which treats an odr index of 0
as power-down and uses a normal dev_err() to report the error in case
odr index point past the initialized part of the array.
Fixes: 1510dd5954 ("lis3lv02d: avoid divide by zero due to unchecked")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=785814
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1817027
BugLink: https://bugs.centos.org/view.php?id=10720
Link: https://lore.kernel.org/r/20210217102501.31758-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 158e800e0f upstream.
A test was added to the probe function to ensure the device was
actually connected and working before successfully completing a
probe. If the device was actually there, but the I2C bus was not
ready yet for whatever reason, the probe fails permanently.
Change the probe so that we defer the probe on a regmap read
failure so that we try the probe again when the dependent drivers
are potentially loaded. This should not affect the case where the
device truly isn't present because the probe will never successfully
complete.
Fixes: 2aa916e67d ("sc16is7xx: Read the LSR register for basic device presence check")
Cc: stable@vger.kernel.org
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Link: https://lore.kernel.org/r/010101787f9c3fd8-c1815c00-2d6b-4c85-a96a-a13e68597fda-000000@us-west-2.amazonses.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e102429f3 upstream.
Whilst running some basic tests as part of writing up the dt-bindings for
this driver (to follow), it became clear it doesn't actually load
currently.
iio iio:device1: tried to double register : in_incli_x_index
adis16201 spi0.0: Failed to create buffer sysfs interfaces
adis16201: probe of spi0.0 failed with error -16
Looks like a cut and paste / update bug. Fixes tag obviously not accurate
but we don't want to bother carry thing back to before the driver moved
out of staging.
Fixes: 591298e54c ("Staging: iio: accel: adis16201: Move adis16201 driver out of staging")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210321182956.844652-1-jic23@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef85bb582c upstream.
Fix voltage coupler lockup which happens when voltage-spread is out
of range due to a bug in the code. The max-spread requirement shall be
accounted when CPU regulator doesn't have consumers. This problem is
observed on Tegra30 Ouya game console once system-wide DVFS is enabled
in a device-tree.
Fixes: 783807436f ("soc/tegra: regulators: Add regulators coupler for Tegra30")
Cc: stable@vger.kernel.org
Reported-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b50a79957 upstream.
The devfreq->lock is held for time of setup. Release the lock in the
error path, before jumping to the end of the function.
Change the goto destination which frees the allocated memory.
Cc: v5.9+ <stable@vger.kernel.org> # v5.9+
Fixes: 4dc3bab868 ("PM / devfreq: Add support delayed timer for polling mode")
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d0b2a3a87 upstream.
Both TI's AM65x (K3) and TI's K2 PCIe driver are implemented in
pci-keystone. However Only K2 PCIe driver should use it's own pci_ops
for configuration space accesses. But commit 10a797c6e5
("PCI: dwc: keystone: Use pci_ops for config space accessors") used
custom pci_ops for both AM65x and K2. This breaks configuration space
access for AM65x platform. Fix it here.
Link: https://lore.kernel.org/r/20210317131518.11040-1-kishon@ti.com
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: <stable@vger.kernel.org> # v5.10
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f66c53b3b9 upstream.
Defer unloading the MMU after a INVPCID until the instruction emulation
has completed, i.e. until after RIP has been updated.
On VMX, this is a benign bug as VMX doesn't touch the MMU when skipping
an emulated instruction. However, on SVM, if nrip is disabled, the
emulator is used to skip an instruction, which would lead to fireworks
if the emulator were invoked without a valid MMU.
Fixes: eb4b248e15 ("kvm: vmx: Support INVPCID in shadow paging mode")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210305011101.3597423-15-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f626ca6829 upstream.
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
For those systems the PCI BARs that request a mapping in the I/O space
have the length recorded in the corresponding PCI resource set to zero,
which makes it unassigned:
# lspci -s 0031:02:04.0 -v
0031:02:04.0 FDDI network controller: Digital Equipment Corporation PCI-to-PDQ Interface Chip [PFI] FDDI (DEFPA) (rev 02)
Subsystem: Digital Equipment Corporation FDDIcontroller/PCI (DEFPA)
Flags: bus master, medium devsel, latency 136, IRQ 57, NUMA node 8
Memory at 620c080020000 (32-bit, non-prefetchable) [size=128]
I/O ports at <unassigned> [disabled]
Memory at 620c080030000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Kernel driver in use: defxx
Kernel modules: defxx
#
Regardless the driver goes ahead and requests it (here observed with a
Raptor Talos II POWER9 system), resulting in an odd /proc/ioport entry:
# cat /proc/ioports
00000000-ffffffffffffffff : 0031:02:04.0
#
Furthermore, the system gets confused as the driver actually continues
and pokes at those locations, causing a flood of messages being output
to the system console by the underlying system firmware, like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
defxx 0031:02:04.0: enabling device (0140 -> 0142)
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010000
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
and so on and so on (possibly intermixed actually, as there's no locking
between the kernel and the firmware in console port access with this
particular system, but cleaned up above for clarity), and once some 10k
of such pairs of the latter two messages have been produced an interace
eventually shows up in a useless state:
0031:02:04.0: DEFPA at I/O addr = 0x0, IRQ = 57, Hardware addr = 00-00-00-00-00-00
This was not expected to happen as resource handling was added to the
driver a while ago, because it was not known at that time that a PCI
system would be possible that cannot assign port I/O resources, and
oddly enough `request_region' does not fail, which would have caught it.
Correct the problem then by checking for the length of zero for the CSR
resource and bail out gracefully refusing to register an interface if
that turns out to be the case, producing messages like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
0031:02:04.0: Cannot use I/O, no address set, aborting
0031:02:04.0: Recompile driver with "CONFIG_DEFXX_MMIO=y"
Keep the original check for the EISA MMIO resource as implemented,
because in that case the length is hardwired to 0x400 as a consequence
of how the compare/mask address decoding works in the ESIC chip and it
is only the base address that is set to zero if MMIO has been disabled
for the adapter in EISA configuration, which in turn could be a valid
bus address in a legacy-free system implementing PCI, especially for
port I/O.
Where the EISA MMIO resource has been disabled for the adapter in EISA
configuration this arrangement keeps producing messages like:
eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
00:05: Cannot use MMIO, no address set, aborting
00:05: Recompile driver with "CONFIG_DEFXX_MMIO=n"
00:05: Or run ECU and set adapter's MMIO location
with the last two lines now swapped for easier handling in the driver.
There is no need to check for and catch the case of a port I/O resource
not having been assigned for EISA as the adapter uses the slot-specific
I/O space, which gets assigned by how EISA has been specified and maps
directly to the particular slot an option card has been placed in. And
the EISA variant of the adapter has additional registers that are only
accessible via the port I/O space anyway.
While at it factor out the error message calls into helpers and fix an
argument order bug with the `pr_err' call now in `dfx_register_res_err'.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 4d0438e56a ("defxx: Clean up DEFEA resource management")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e98b69700 upstream.
pci_fixup_irqs() used to call pcibios_map_irq on every PCI device, which
for RT2880 included bus 0 slot 0. After pci_fixup_irqs() got removed,
only slots/funcs with devices attached would be called. While arguably
the right thing, that left no chance for this driver to ever initialize
slot 0, effectively bricking PCI and USB on RT2880 devices such as the
Belkin F5D8235-4 v1.
Slot 0 configuration needs to happen after PCI bus enumeration, but
before any device at slot 0x11 (func 0 or 1) is talked to. That was
determined empirically by testing on a Belkin F5D8235-4 v1 device. A
minimal BAR 0 config write followed by read, then setting slot 0
PCI_COMMAND to MASTER | IO | MEMORY is all that seems to be required for
proper functionality.
Tested by ensuring that full- and high-speed USB devices get enumerated
on the Belkin F5D8235-4 v1 (with an out of tree DTS file from OpenWrt).
Fixes: 04c81c7293 ("MIPS: PCI: Replace pci_fixup_irqs() call with host bridge IRQ mapping hooks")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tobias Wolf <dev-NTEO@vplace.de>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a523ef731a upstream.
kabylake_ssp_fixup function uses snd_soc_dpcm to identify the
codecs DAIs. The HW parameters are changed based on the codec DAI of the
stream. The earlier approach to get snd_soc_dpcm was using container_of()
macro on snd_pcm_hw_params.
The structures have been modified over time and snd_soc_dpcm does not have
snd_pcm_hw_params as a reference but as a copy. This causes the current
driver to crash when used.
This patch changes the way snd_soc_dpcm is extracted. snd_soc_pcm_runtime
holds 2 dpcm instances (one for playback and one for capture). 2 codecs
on the SSP are dmic (capture) and speakers (playback). Based on the
stream direction, snd_soc_dpcm is extracted from snd_soc_pcm_runtime.
Tested for all use cases of the driver.
Based on similar fix in kbl_rt5663_rt5514_max98927.c
from Harsha Priya <harshapriya.n@intel.com> and
Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Cc: <stable@vger.kernel.org> # 5.4+
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210415124347.475432-1-lma@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d58970da32 upstream.
cppcheck warning:
sound/soc/samsung/tm2_wm5110.c:605:6: style: Variable 'ret' is
reassigned a value before the old one has been
used. [redundantAssignment]
ret = devm_snd_soc_register_component(dev, &tm2_component,
^
sound/soc/samsung/tm2_wm5110.c:554:7: note: ret is assigned
ret = of_parse_phandle_with_args(dev->of_node, "i2s-controller",
^
sound/soc/samsung/tm2_wm5110.c:605:6: note: ret is overwritten
ret = devm_snd_soc_register_component(dev, &tm2_component,
^
The args is a stack variable, so it could have junk (uninitialized)
therefore args.np could have a non-NULL and random value even though
property was missing. Later could trigger invalid pointer dereference.
There's no need to check for args.np because args.np won't be
initialized on errors.
Fixes: 8d1513cef5 ("ASoC: samsung: Add support for HDMI audio on TM2 board")
Cc: <stable@vger.kernel.org>
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312180231.2741-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3a0720224 upstream.
tcpm_pd_select_pps_apdo overwrites port->pps_data.min_volt,
port->pps_data.max_volt, port->pps_data.max_curr even before
port partner accepts the requests. This leaves incorrect values
in current_limit and supply_voltage that get exported by
"tcpm-source-psy-". Solving this problem by caching the request
values in req_min_volt, req_max_volt, req_max_curr, req_out_volt,
req_op_curr. min_volt, max_volt, max_curr gets updated once the
partner accepts the request. current_limit, supply_voltage gets updated
once local port's tcpm enters SNK_TRANSITION_SINK when the accepted
current_limit and supply_voltage is enforced.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through power_supply")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210407200723.1914388-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d732690d2 upstream.
The port close_delay and closing_wait parameters set by TIOCSSERIAL are
specified in jiffies and not milliseconds.
Add the missing conversions so that the TIOCSSERIAL works as expected
also when HZ is not 1000.
Fixes: 02303f7337 ("usb-wwan: implement TIOCGSERIAL and TIOCSSERIAL to avoid blocking close(2)")
Cc: stable@vger.kernel.org # 2.6.38
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2a91a2d5 upstream.
usb_role_switch_find_by_fwnode() returns a reference to the role-switch
which must be put by calling usb_role_switch_put().
usb_role_switch_put() calls module_put(sw->dev.parent->driver->owner),
add a matching try_module_get() to usb_role_switch_find_by_fwnode(),
making it behave the same as the other usb_role_switch functions
which return a reference.
This avoids a WARN_ON being hit at kernel/module.c:1158 due to the
module-refcount going below 0.
Fixes: c6919d5e0c ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409124136.65591-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 729f7955cb upstream.
This reverts commit b401f8c4f4.
The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.
With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).
Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).
For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1f8280887 upstream.
Read and write operations are capped to MAX_RW_COUNT. Some read ops rely on
that limit, and that is not guaranteed by the IORING_OP_PROVIDE_BUFFERS.
Truncate those lengths when doing io_add_buffers, so buffer addresses still
use the uncapped length.
Also, take the chance and change struct io_buffer len member to __u32, so
it matches struct io_provide_buffer len member.
This fixes CVE-2021-3491, also reported as ZDI-CAN-13546.
Fixes: ddf0322db7 ("io_uring: add IORING_OP_PROVIDE_BUFFERS")
Reported-by: Billy Jheng Bing-Jhong (@st424204)
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c61760e694 upstream.
Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()")
and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
fixed a refcount leak bug in bind/connect but introduced a
use-after-free if the same local is assigned to 2 different sockets.
This can be triggered by the following simple program:
int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) );
addr.sa_family = AF_NFC;
addr.nfc_protocol = NFC_PROTO_NFC_DEP;
bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
close(sock1);
close(sock2);
Fix this by assigning NULL to llcp_sock->local after calling
nfc_llcp_local_put.
This addresses CVE-2021-23134.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Reported-by: Nadav Markus <nmarkus@paloaltonetworks.com>
Fixes: c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2cb6b891a upstream.
There is a possible race condition vulnerability between issuing a HCI
command and removing the cont. Specifically, functions hci_req_sync()
and hci_dev_do_close() can race each other like below:
thread-A in hci_req_sync() | thread-B in hci_dev_do_close()
| hci_req_sync_lock(hdev);
test_bit(HCI_UP, &hdev->flags); |
... | test_and_clear_bit(HCI_UP, &hdev->flags)
hci_req_sync_lock(hdev); |
|
In this commit we alter the sequence in function hci_req_sync(). Hence,
the thread-A cannot issue th.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Cc: Marcel Holtmann <marcel@holtmann.org>
Fixes: 7c6a329e44 ("[Bluetooth] Fix regression from using default link policy")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c4c8c9544 upstream.
hci_chan can be created in 2 places: hci_loglink_complete_evt() if
it is an AMP hci_chan, or l2cap_conn_add() otherwise. In theory,
Only AMP hci_chan should be removed by a call to
hci_disconn_loglink_complete_evt(). However, the controller might mess
up, call that function, and destroy an hci_chan which is not initiated
by hci_loglink_complete_evt().
This patch adds a verification that the destroyed hci_chan must have
been init'd by hci_loglink_complete_evt().
Example crash call trace:
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe3/0x144 lib/dump_stack.c:118
print_address_description+0x67/0x22a mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report mm/kasan/report.c:412 [inline]
kasan_report+0x251/0x28f mm/kasan/report.c:396
hci_send_acl+0x3b/0x56e net/bluetooth/hci_core.c:4072
l2cap_send_cmd+0x5af/0x5c2 net/bluetooth/l2cap_core.c:877
l2cap_send_move_chan_cfm_icid+0x8e/0xb1 net/bluetooth/l2cap_core.c:4661
l2cap_move_fail net/bluetooth/l2cap_core.c:5146 [inline]
l2cap_move_channel_rsp net/bluetooth/l2cap_core.c:5185 [inline]
l2cap_bredr_sig_cmd net/bluetooth/l2cap_core.c:5464 [inline]
l2cap_sig_channel net/bluetooth/l2cap_core.c:5799 [inline]
l2cap_recv_frame+0x1d12/0x51aa net/bluetooth/l2cap_core.c:7023
l2cap_recv_acldata+0x2ea/0x693 net/bluetooth/l2cap_core.c:7596
hci_acldata_packet net/bluetooth/hci_core.c:4606 [inline]
hci_rx_work+0x2bd/0x45e net/bluetooth/hci_core.c:4796
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
Allocated by task 38:
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0x8d/0x9a mm/kasan/kasan.c:553
kmem_cache_alloc_trace+0x102/0x129 mm/slub.c:2787
kmalloc include/linux/slab.h:515 [inline]
kzalloc include/linux/slab.h:709 [inline]
hci_chan_create+0x86/0x26d net/bluetooth/hci_conn.c:1674
l2cap_conn_add.part.0+0x1c/0x814 net/bluetooth/l2cap_core.c:7062
l2cap_conn_add net/bluetooth/l2cap_core.c:7059 [inline]
l2cap_connect_cfm+0x134/0x852 net/bluetooth/l2cap_core.c:7381
hci_connect_cfm+0x9d/0x122 include/net/bluetooth/hci_core.h:1404
hci_remote_ext_features_evt net/bluetooth/hci_event.c:4161 [inline]
hci_event_packet+0x463f/0x72fa net/bluetooth/hci_event.c:5981
hci_rx_work+0x197/0x45e net/bluetooth/hci_core.c:4791
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
Freed by task 1732:
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free mm/kasan/kasan.c:521 [inline]
__kasan_slab_free+0x106/0x128 mm/kasan/kasan.c:493
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook+0xaa/0xf6 mm/slub.c:1436
slab_free mm/slub.c:3009 [inline]
kfree+0x182/0x21e mm/slub.c:3972
hci_disconn_loglink_complete_evt net/bluetooth/hci_event.c:4891 [inline]
hci_event_packet+0x6a1c/0x72fa net/bluetooth/hci_event.c:6050
hci_rx_work+0x197/0x45e net/bluetooth/hci_core.c:4791
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
The buggy address belongs to the object at ffff8881d7af9180
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 24 bytes inside of
128-byte region [ffff8881d7af9180, ffff8881d7af9200)
The buggy address belongs to the page:
page:ffffea00075ebe40 count:1 mapcount:0 mapping:ffff8881da403200 index:0x0
flags: 0x8000000000000200(slab)
raw: 8000000000000200 dead000000000100 dead000000000200 ffff8881da403200
raw: 0000000000000000 0000000080150015 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881d7af9080: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8881d7af9100: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8881d7af9180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881d7af9200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881d7af9280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+98228e7407314d2d4ba2@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34ab17cc6c upstream.
Slab OOB issue is scanned by KASAN in cpu_power_to_freq().
If power is limited below the power of OPP0 in EM table,
it will cause slab out-of-bound issue with negative array
index.
Return the lowest frequency if limited power cannot found
a suitable OPP in EM table to fix this issue.
Backtrace:
[<ffffffd02d2a37f0>] die+0x104/0x5ac
[<ffffffd02d2a5630>] bug_handler+0x64/0xd0
[<ffffffd02d288ce4>] brk_handler+0x160/0x258
[<ffffffd02d281e5c>] do_debug_exception+0x248/0x3f0
[<ffffffd02d284488>] el1_dbg+0x14/0xbc
[<ffffffd02d75d1d4>] __kasan_report+0x1dc/0x1e0
[<ffffffd02d75c2e0>] kasan_report+0x10/0x20
[<ffffffd02d75def8>] __asan_report_load8_noabort+0x18/0x28
[<ffffffd02e6fce5c>] cpufreq_power2state+0x180/0x43c
[<ffffffd02e6ead80>] power_actor_set_power+0x114/0x1d4
[<ffffffd02e6fac24>] allocate_power+0xaec/0xde0
[<ffffffd02e6f9f80>] power_allocator_throttle+0x3ec/0x5a4
[<ffffffd02e6ea888>] handle_thermal_trip+0x160/0x294
[<ffffffd02e6edd08>] thermal_zone_device_check+0xe4/0x154
[<ffffffd02d351cb4>] process_one_work+0x5e4/0xe28
[<ffffffd02d352f44>] worker_thread+0xa4c/0xfac
[<ffffffd02d360124>] kthread+0x33c/0x358
[<ffffffd02d289940>] ret_from_fork+0xc/0x18
Fixes: 371a3bc79c ("thermal/drivers/cpufreq_cooling: Fix wrong frequency converted from power")
Signed-off-by: brian-sy yang <brian-sy.yang@mediatek.com>
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Cc: stable@vger.kernel.org #v5.7
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201229050831.19493-1-michael.kao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84696cfaf4 upstream.
Commit 9af7706492 ("lib/vsprintf: Remove support for %pF and %pf in
favour of %pS and %ps") removed support for %pF and %pf, and correctly
removed the handling of those cases in vbin_printf(). However, the
corresponding cases in bstr_printf() were left behind.
In the same series, %pf was re-purposed for dealing with
fwnodes (3bd32d6a2e, "lib/vsprintf: Add %pfw conversion specifier
for printing fwnode names").
So should anyone use %pf with the binary printf routines,
vbin_printf() would (correctly, as it involves dereferencing the
pointer) do the string formatting to the u32 array, but bstr_printf()
would not copy the string from the u32 array, but instead interpret
the first sizeof(void*) bytes of the formatted string as a pointer -
which generally won't end well (also, all subsequent get_args would be
out of sync).
Fixes: 9af7706492 ("lib/vsprintf: Remove support for %pF and %pf in favour of %pS and %ps")
Cc: stable@vger.kernel.org
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210423094529.1862521-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e947c8f4a upstream.
When loading a device-mapper table for a request-based mapped device,
and the allocation/initialization of the blk_mq_tag_set for the device
fails, a following device remove will cause a double free.
E.g. (dmesg):
device-mapper: core: Cannot initialize queue for request-based dm-mq mapped device
device-mapper: ioctl: unable to set up device queue for new table.
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0305e098835de000 TEID: 0305e098835de803
Fault in home space mode while using kernel ASCE.
AS:000000025efe0007 R3:0000000000000024
Oops: 0038 ilc:3 [#1] SMP
Modules linked in: ... lots of modules ...
Supported: Yes, External
CPU: 0 PID: 7348 Comm: multipathd Kdump: loaded Tainted: G W X 5.3.18-53-default #1 SLE15-SP3
Hardware name: IBM 8561 T01 7I2 (LPAR)
Krnl PSW : 0704e00180000000 000000025e368eca (kfree+0x42/0x330)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 000000000000004a 000000025efe5230 c1773200d779968d 0000000000000000
000000025e520270 000000025e8d1b40 0000000000000003 00000007aae10000
000000025e5202a2 0000000000000001 c1773200d779968d 0305e098835de640
00000007a8170000 000003ff80138650 000000025e5202a2 000003e00396faa8
Krnl Code: 000000025e368eb8: c4180041e100 lgrl %r1,25eba50b8
000000025e368ebe: ecba06b93a55 risbg %r11,%r10,6,185,58
#000000025e368ec4: e3b010000008 ag %r11,0(%r1)
>000000025e368eca: e310b0080004 lg %r1,8(%r11)
000000025e368ed0: a7110001 tmll %r1,1
000000025e368ed4: a7740129 brc 7,25e369126
000000025e368ed8: e320b0080004 lg %r2,8(%r11)
000000025e368ede: b904001b lgr %r1,%r11
Call Trace:
[<000000025e368eca>] kfree+0x42/0x330
[<000000025e5202a2>] blk_mq_free_tag_set+0x72/0xb8
[<000003ff801316a8>] dm_mq_cleanup_mapped_device+0x38/0x50 [dm_mod]
[<000003ff80120082>] free_dev+0x52/0xd0 [dm_mod]
[<000003ff801233f0>] __dm_destroy+0x150/0x1d0 [dm_mod]
[<000003ff8012bb9a>] dev_remove+0x162/0x1c0 [dm_mod]
[<000003ff8012a988>] ctl_ioctl+0x198/0x478 [dm_mod]
[<000003ff8012ac8a>] dm_ctl_ioctl+0x22/0x38 [dm_mod]
[<000000025e3b11ee>] ksys_ioctl+0xbe/0xe0
[<000000025e3b127a>] __s390x_sys_ioctl+0x2a/0x40
[<000000025e8c15ac>] system_call+0xd8/0x2c8
Last Breaking-Event-Address:
[<000000025e52029c>] blk_mq_free_tag_set+0x6c/0xb8
Kernel panic - not syncing: Fatal exception: panic_on_oops
When allocation/initialization of the blk_mq_tag_set fails in
dm_mq_init_request_queue(), it is uninitialized/freed, but the pointer
is not reset to NULL; so when dev_remove() later gets into
dm_mq_cleanup_mapped_device() it sees the pointer and tries to
uninitialize and free it again.
Fix this by setting the pointer to NULL in dm_mq_init_request_queue()
error-handling. Also set it to NULL in dm_mq_cleanup_mapped_device().
Cc: <stable@vger.kernel.org> # 4.6+
Fixes: 1c357a1e86 ("dm: allocate blk_mq_tag_set rather than embed in mapped_device")
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aafe104aa9 upstream.
It was reported that a fix to the ring buffer recursion detection would
cause a hung machine when performing suspend / resume testing. The
following backtrace was extracted from debugging that case:
Call Trace:
trace_clock_global+0x91/0xa0
__rb_reserve_next+0x237/0x460
ring_buffer_lock_reserve+0x12a/0x3f0
trace_buffer_lock_reserve+0x10/0x50
__trace_graph_return+0x1f/0x80
trace_graph_return+0xb7/0xf0
? trace_clock_global+0x91/0xa0
ftrace_return_to_handler+0x8b/0xf0
? pv_hash+0xa0/0xa0
return_to_handler+0x15/0x30
? ftrace_graph_caller+0xa0/0xa0
? trace_clock_global+0x91/0xa0
? __rb_reserve_next+0x237/0x460
? ring_buffer_lock_reserve+0x12a/0x3f0
? trace_event_buffer_lock_reserve+0x3c/0x120
? trace_event_buffer_reserve+0x6b/0xc0
? trace_event_raw_event_device_pm_callback_start+0x125/0x2d0
? dpm_run_callback+0x3b/0xc0
? pm_ops_is_empty+0x50/0x50
? platform_get_irq_byname_optional+0x90/0x90
? trace_device_pm_callback_start+0x82/0xd0
? dpm_run_callback+0x49/0xc0
With the following RIP:
RIP: 0010:native_queued_spin_lock_slowpath+0x69/0x200
Since the fix to the recursion detection would allow a single recursion to
happen while tracing, this lead to the trace_clock_global() taking a spin
lock and then trying to take it again:
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* lock taken */
(something else gets traced by function graph tracer)
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* DEAD LOCK! */
Tracing should *never* block, as it can lead to strange lockups like the
above.
Restructure the trace_clock_global() code to instead of simply taking a
lock to update the recorded "prev_time" simply use it, as two events
happening on two different CPUs that calls this at the same time, really
doesn't matter which one goes first. Use a trylock to grab the lock for
updating the prev_time, and if it fails, simply try again the next time.
If it failed to be taken, that means something else is already updating
it.
Link: https://lkml.kernel.org/r/20210430121758.650b6e8a@gandalf.local.home
Cc: stable@vger.kernel.org
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Fixes: b02414c8f0 ("ring-buffer: Fix recursion protection transitions between interrupt context") # started showing the problem
Fixes: 14131f2f98 ("tracing: implement trace_clock_*() APIs") # where the bug happened
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212761
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
