commit f18d0076933689775fe7faeeb10ee93ff01be6ab upstream.
In case of the COW file, new updates and GC writes are already
separated to page caches of the atomic file and COW file. As some cases
that use the meta inode for GC, there are some race issues between a
foreground thread and GC thread.
To handle them, we need to take care when to invalidate and wait
writeback of GC pages in COW files as the case of using the meta inode.
Also, a pointer from the COW inode to the original inode is required to
check the state of original pages.
For the former, we can solve the problem by using the meta inode for GC
of COW files. Then let's get a page from the original inode in
move_data_block when GCing the COW file to avoid race condition.
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Cc: stable@vger.kernel.org #v5.19+
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40a2b00370931b0c50148681dd7364573e52e6b upstream.
The page cache of the atomic file keeps new data pages which will be
stored in the COW file. It can also keep old data pages when GCing the
atomic file. In this case, new data can be overwritten by old data if a
GC thread sets the old data page as dirty after new data page was
evicted.
Also, since all writes to the atomic file are redirected to COW inodes,
GC for the atomic file is not working well as below.
f2fs_gc(gc_type=FG_GC)
- select A as a victim segment
do_garbage_collect
- iget atomic file's inode for block B
move_data_page
f2fs_do_write_data_page
- use dn of cow inode
- set fio->old_blkaddr from cow inode
- seg_freed is 0 since block B is still valid
- goto gc_more and A is selected as victim again
To solve the problem, let's separate GC writes and updates in the atomic
file by using the meta inode for GC writes.
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Cc: stable@vger.kernel.org #v5.19+
Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com>
Reviewed-by: Yeongjin Gil <youngjin.gil@samsung.com>
Signed-off-by: Sunmin Jeong <s_min.jeong@samsung.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c8764f8679e659c5cb295af7d32279002d13735 upstream.
It will return all zero data when DIO reading from inline_data inode, it
is because f2fs_iomap_begin() assign iomap->type w/ IOMAP_HOLE incorrectly
for this case.
We can let iomap framework handle inline data via assigning iomap->type
and iomap->inline_data correctly, however, it will be a little bit
complicated when handling race case in between direct IO and buffered IO.
So, let's force to use buffered IO to fix this issue.
Cc: stable@vger.kernel.org
Reported-by: Barry Song <v-songbaohua@oppo.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fef55d8f78383c8e6d6d4c014b9597375132696 upstream.
If an NTFS file system is mounted to another system with different
PAGE_SIZE from the original system, log->page_size will change in
log_replay(), but log->page_{mask,bits} don't change correspondingly.
This will cause a panic because "u32 bytes = log->page_size - page_off"
will get a negative value in the later read_log_page().
Cc: stable@vger.kernel.org
Fixes: b46acd6a6a ("fs/ntfs3: Add NTFS journal")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee8b8f5d83eb2c9caaebcf633310905ee76856e9 upstream.
After calling uefi interface allocate_pool to apply for memory, we
should clear 0 to prevent the possibility of using random values.
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Cc: <stable@vger.kernel.org> # v6.6+
Fixes: 732ea9db9d ("efi: libstub: Move screen_info handling to common code")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 267ed02c2121b75e0eaaa338240453b576039e4a upstream.
dev_t is a kernel type and may have different definitions
in kernel and userspace. On 32-bit x86 this currently makes
the stat structure being 4 bytes longer in the user code,
causing stack corruption.
However, this is (potentially) not the only problem, since
dev_t is a different type on user/kernel side, so we don't
know that the major/minor encoding isn't also different.
Decode/encode it instead to address both problems.
Cc: stable@vger.kernel.org
Fixes: 74ce793bcb ("hostfs: Fix ephemeral inodes")
Link: https://patch.msgid.link/20240702092440.acc960585dd5.Id0767e12f562a69c6cd3c3262dc3d765db350cf6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31643d84b8c3d9c846aa0e20bc033e46c68c7e7d upstream.
With the introduction of binder_available_for_proc_work_ilocked() in
commit 1b77e9dcc3 ("ANDROID: binder: remove proc waitqueue") a binder
thread can only "wait_for_proc_work" after its thread->looper has been
marked as BINDER_LOOPER_STATE_{ENTERED|REGISTERED}.
This means an unregistered reader risks waiting indefinitely for work
since it never gets added to the proc->waiting_threads. If there are no
further references to its waitqueue either the task will hang. The same
applies to readers using the (e)poll interface.
I couldn't find the rationale behind this restriction. So this patch
restores the previous behavior of allowing unregistered threads to
"wait_for_proc_work". Note that an error message for this scenario,
which had previously become unreachable, is now re-enabled.
Fixes: 1b77e9dcc3 ("ANDROID: binder: remove proc waitqueue")
Cc: stable@vger.kernel.org
Cc: Martijn Coenen <maco@google.com>
Cc: Arve Hjønnevåg <arve@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20240711201452.2017543-1-cmllamas@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4bbcac11d3cea85822af8b40daed7e96bca5068 upstream.
The LS7A chipset can be used as part of a PCIe Root Complex with
Loongson-3C6000 and similar CPUs. In this case, DEV_LS7A_PCIE_PORT5 has a
PCI_CLASS_BRIDGE_HOST class code, and it is a Type 0 Function whose config
space provides access to Root Complex registers.
The DEV_LS7A_PCIE_PORT5 has an MSI Capability, and its MSI Enable bit must
be set before other devices below the Root Complex can use MSI. This is
not the standard PCI behavior of MSI Enable, so the normal PCI MSI code
does not set it.
Set the DEV_LS7A_PCIE_PORT5 MSI Enable bit via a quirk so other devices
below the Root Complex can use MSI.
[kwilczynski: exit early to reduce indentation; commit log]
Link: https://lore.kernel.org/linux-pci/20240612065315.2048110-1-chenhuacai@loongson.cn
Signed-off-by: Sheng Wu <wusheng@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 840b7a5edf88fe678c60dee88a135647c0ea4375 upstream.
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28b8d7793b8573563b3d45321376f36168d77b1e upstream.
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fea93a3e5d5e6a09eb153866d2ce60ea3287a70d upstream.
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c29ab84cfec17081aae7a7a28f8d2c93c42dcae upstream.
Fix warning at drivers/pci/msi/msi.h:121.
Recently, I added a PCI to PCIe bridge adaptor and a PCIe NVME card
to my rp3440. Then, I noticed this warning at boot:
WARNING: CPU: 0 PID: 10 at drivers/pci/msi/msi.h:121 pci_msi_setup_msi_irqs+0x68/0x90
CPU: 0 PID: 10 Comm: kworker/u32:0 Not tainted 6.9.7-parisc64 #1 Debian 6.9.7-1
Hardware name: 9000/800/rp3440
Workqueue: async async_run_entry_fn
We need to select PCI_MSI_ARCH_FALLBACKS when PCI_MSI is selected.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14cba6ace79627a57fb9058582b03f0ed3832390 upstream.
amd_rng_mod_init() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The return code is then returned as is but amd_rng_mod_init() is
a module_init() function that should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it.
Fixes: 96d63c0297 ("[PATCH] Add AMD HW RNG driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c830eef806679dc243e191f962c488dd9d00708 upstream.
Andrea reported that the following innocuous litmus test:
C T
{}
P0(spinlock_t *x)
{
int r0;
spin_lock(x);
spin_unlock(x);
r0 = spin_is_locked(x);
}
gives rise to a nonsensical empty result with no executions:
$ herd7 -conf linux-kernel.cfg T.litmus
Test T Required
States 0
Ok
Witnesses
Positive: 0 Negative: 0
Condition forall (true)
Observation T Never 0 0
Time T 0.00
Hash=6fa204e139ddddf2cb6fa963bad117c0
The problem is caused by a bug in the lock.cat part of the LKMM. Its
computation of the rf relation for RU (read-unlocked) events is
faulty; it implicitly assumes that every RU event must read from
either a UL (unlock) event in another thread or from the lock's
initial state. Neither is true in the litmus test above, so the
computation yields no possible executions.
The lock.cat code tries to make up for this deficiency by allowing RU
events outside of critical sections to read from the last po-previous
UL event. But it does this incorrectly, trying to keep these rfi links
separate from the rfe links that might also be needed, and passing only
the latter to herd7's cross() macro.
The problem is fixed by merging the two sets of possible rf links for
RU events and using them all in the call to cross().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrea Parri <parri.andrea@gmail.com>
Closes: https://lore.kernel.org/linux-arch/ZlC0IkzpQdeGj+a3@andrea/
Tested-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Andrea Parri <parri.andrea@gmail.com>
Fixes: 15553dcbca ("tools/memory-model: Add model support for spin_is_locked()")
CC: <stable@vger.kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21451dfd853e7d8e6e3fbd7ef1fbdb2f2ead12f5 upstream.
Sonix HD USB Camera does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x84".
This patch adds the USB ID to quirks.c and avoids those error messages.
(snip)
[1.789698] usb 3-3: new high-speed USB device number 2 using xhci_hcd
[1.984121] usb 3-3: New USB device found, idVendor=0c45, idProduct=6340, bcdDevice= 0.00
[1.984124] usb 3-3: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[1.984127] usb 3-3: Product: USB 2.0 Camera
[1.984128] usb 3-3: Manufacturer: Sonix Technology Co., Ltd.
[5.440957] usb 3-3: 3:1: cannot get freq at ep 0x84
[12.130679] usb 3-3: 3:1: cannot get freq at ep 0x84
[12.175065] usb 3-3: 3:1: cannot get freq at ep 0x84
Signed-off-by: wangdicheng <wangdicheng@kylinos.cn>
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20240722084822.31620-1-wangdich9700@163.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32f55e475ce2c4b8b124d335fcfaf1152ba977a1 upstream.
When requesting an immediate exit from L2 in order to inject a pending
event, do so only if the pending event actually requires manual injection,
i.e. if and only if KVM actually needs to regain control in order to
deliver the event.
Avoiding the "immediate exit" isn't simply an optimization, it's necessary
to make forward progress, as the "already expired" VMX preemption timer
trick that KVM uses to force a VM-Exit has higher priority than events
that aren't directly injected.
At present time, this is a glorified nop as all events processed by
vmx_has_nested_events() require injection, but that will not hold true in
the future, e.g. if there's a pending virtual interrupt in vmcs02.RVI.
I.e. if KVM is trying to deliver a virtual interrupt to L2, the expired
VMX preemption timer will trigger VM-Exit before the virtual interrupt is
delivered, and KVM will effectively hang the vCPU in an endless loop of
forced immediate VM-Exits (because the pending virtual interrupt never
goes away).
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240607172609.3205077-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 322a569c4b4188a0da2812f9e952780ce09b74ba upstream.
Move the non-VMX chunk of the "interrupt blocked" checks to a separate
helper so that KVM can reuse the code to detect if interrupts are blocked
for L2, e.g. to determine if a virtual interrupt _for L2_ is a valid wake
event. If L1 disables HLT-exiting for L2, nested APICv is enabled, and L2
HLTs, then L2 virtual interrupts are valid wake events, but if and only if
interrupts are unblocked for L2.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240607172609.3205077-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a813f168336ec4ef725b836e598cd9dc14f76dd7 upstream.
Prior to the ongoing command privacy is on, it would return -1 to
indicate the current privacy status, and the ongoing command would
be well executed by firmware as well, so this is not error. This
patch changes its behavior to notify privacy on directly by V4L2
privacy control instead of reporting error.
Fixes: 29006e196a ("media: pci: intel: ivsc: Add CSI submodule")
Cc: stable@vger.kernel.org # for 6.6 and later
Reported-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27ba5b67312a944576addc4df44ac3b709aabede upstream.
Commit 9f356e5a4f ("jbd2: Account descriptor blocks into
t_outstanding_credits") started to account descriptor blocks into
transactions outstanding credits. However it didn't appropriately
decrease the maximum amount of credits available to userspace. Thus if
the filesystem requests a transaction smaller than
j_max_transaction_buffers but large enough that when descriptor blocks
are added the size exceeds j_max_transaction_buffers, we confuse
add_transaction_credits() into thinking previous handles have grown the
transaction too much and enter infinite journal commit loop in
start_this_handle() -> add_transaction_credits() trying to create
transaction with enough credits available.
Fix the problem by properly accounting for transaction space reserved
for descriptor blocks when verifying requested transaction handle size.
CC: stable@vger.kernel.org
Fixes: 9f356e5a4f ("jbd2: Account descriptor blocks into t_outstanding_credits")
Reported-by: Alexander Coffin <alex.coffin@maticrobots.com>
Link: https://lore.kernel.org/all/CA+hUFcuGs04JHZ_WzA1zGN57+ehL2qmHOt5a7RMpo+rv6Vyxtw@mail.gmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20240624170127.3253-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3a00a23781c1f2fcda98a7aecaac515558e7a35 upstream.
Instead of computing the number of descriptor blocks a transaction can
have each time we need it (which is currently when starting each
transaction but will become more frequent later) precompute the number
once during journal initialization together with maximum transaction
size. We perform the precomputation whenever journal feature set is
updated similarly as for computation of
journal->j_revoke_records_per_block.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20240624170127.3253-2-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa99c71e42ad60178c1154ec24e3df9c684fb67 upstream.
There's no reason to have jbd2_journal_get_max_txn_bufs() public
function. Currently all users are internal and can use
journal->j_max_transaction_buffers instead. This saves some unnecessary
recomputations of the limit as a bonus which becomes important as this
function gets more complex in the following patch.
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20240624170127.3253-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6be6471004e0e4d10d0514146d8c41550823d63 upstream.
There're possibilities that privacy status change notification happens
in the middle of the ongoing mei command which already takes the command
lock, but v4l2_ctrl_s_ctrl() would also need the same lock prior to this
patch, so this may results in circular locking problem. This patch adds
one dedicated lock for v4l2 control handler to avoid described issue.
Fixes: 29006e196a ("media: pci: intel: ivsc: Add CSI submodule")
Cc: stable@vger.kernel.org # for 6.6 and later
Reported-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab99a87542f194f28e2364a42afbf9fb48b1c724 upstream.
__write_sb_page() rounds up the io size to the optimal io size if it
doesn't exceed the data offset, but it doesn't check the final size
exceeds the bitmap length.
For example:
page count - 1
page size - 4K
data offset - 1M
optimal io size - 256K
The final io size would be 256K (64 pages) but md_bitmap_storage_alloc()
allocated 1 page, the IO would write 1 valid page and 63 pages that
happens to be allocated afterwards. This leaks memory to the raid device
superblock.
This issue caused a data transfer failure in nvme-tcp. The network
drivers checks the first page of an IO with sendpage_ok(), it returns
true if the page isn't a slabpage and refcount >= 1. If the page
!sendpage_ok() the network driver disables MSG_SPLICE_PAGES.
As of now the network layer assumes all the pages of the IO are
sendpage_ok() when MSG_SPLICE_PAGES is on.
The bitmap pages aren't slab pages, the first page of the IO is
sendpage_ok(), but the additional pages that happens to be allocated
after the bitmap pages might be !sendpage_ok(). That cause
skb_splice_from_iter() to stop the data transfer, in the case below it
hangs 'mdadm --create'.
The bug is reproducible, in order to reproduce we need nvme-over-tcp
controllers with optimal IO size bigger than PAGE_SIZE. Creating a raid
with bitmap over those devices reproduces the bug.
In order to simulate large optimal IO size you can use dm-stripe with a
single device.
Script to reproduce the issue on top of brd devices using dm-stripe is
attached below (will be added to blktest).
I have added some logs to test the theory:
...
md: created bitmap (1 pages) for device md127
__write_sb_page before md_super_write offset: 16, size: 262144. pfn: 0x53ee
=== __write_sb_page before md_super_write. logging pages ===
pfn: 0x53ee, slab: 0 <-- the only page that allocated for the bitmap
pfn: 0x53ef, slab: 1
pfn: 0x53f0, slab: 0
pfn: 0x53f1, slab: 0
pfn: 0x53f2, slab: 0
pfn: 0x53f3, slab: 1
...
nvme_tcp: sendpage_ok - pfn: 0x53ee, len: 262144, offset: 0
skbuff: before sendpage_ok() - pfn: 0x53ee
skbuff: before sendpage_ok() - pfn: 0x53ef
WARNING at net/core/skbuff.c:6848 skb_splice_from_iter+0x142/0x450
skbuff: !sendpage_ok - pfn: 0x53ef. is_slab: 1, page_count: 1
...
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ofir Gal <ofir.gal@volumez.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240607072748.3182199-1-ofir.gal@volumez.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce068e83976140badb19c7f1307926b4b562fac4 upstream.
ich7_lpc_probe() uses pci_read_config_dword() that returns PCIBIOS_*
codes. The error handling code assumes incorrectly it's a normal errno
and checks for < 0. The return code is returned from the probe function
as is but probe functions should return normal errnos.
Remove < 0 from the check and convert PCIBIOS_* returns code using
pcibios_err_to_errno() into normal errno before returning it.
Fixes: a328e95b82 ("leds: LED driver for Intel NAS SS4200 series (v5)")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240527132700.14260-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b003e14801cf85a8cebeddc87bc9fc77100fdce upstream.
Currently return status is not getting checked for get_api_version
and because of that for x86 arch we are getting below smatch error.
CC drivers/soc/xilinx/zynqmp_power.o
drivers/soc/xilinx/zynqmp_power.c: In function 'zynqmp_pm_probe':
drivers/soc/xilinx/zynqmp_power.c:295:12: warning: 'pm_api_version' is
used uninitialized [-Wuninitialized]
295 | if (pm_api_version < ZYNQMP_PM_VERSION)
| ^
CHECK drivers/soc/xilinx/zynqmp_power.c
drivers/soc/xilinx/zynqmp_power.c:295 zynqmp_pm_probe() error:
uninitialized symbol 'pm_api_version'.
So, check return status of pm_get_api_version and return error in case
of failure to avoid checking uninitialized pm_api_version variable.
Fixes: b9b3a8be28 ("firmware: xilinx: Remove eemi ops for get_api_version")
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@amd.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240515112345.24673-1-jay.buddhabhatti@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28818b4d871bc93cc4f5c7c7d7c526a6a096c09c upstream.
When there is beacon loss, for example due to unrelated Bluetooth
devices transmitting music nearby, the wifi connection dies soon
after the first beacon loss message:
Apr 28 20:47:14 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-BEACON-LOSS
Apr 28 20:47:15 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-DISCONNECTED bssid=... reason=4 locally_generated=1
Apr 28 20:47:24 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-BEACON-LOSS
Apr 28 20:47:25 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-DISCONNECTED bssid=... reason=4 locally_generated=1
Apr 28 20:47:34 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-BEACON-LOSS
Apr 28 20:47:35 ideapad2 wpa_supplicant[1161]: wlp3s0f3u4:
CTRL-EVENT-DISCONNECTED bssid=... reason=4 locally_generated=1
When the beacon loss happens, mac80211 makes rtw88 transmit a QOS
NULL frame and asks to confirm the ACK status. Even though rtw88
confirms to mac80211 that the QOS NULL was transmitted successfully,
the connection still dies. This is because rtw88 is handing the QOS
NULL back to mac80211 with skb->data pointing to the headroom (the
TX descriptor) instead of ieee80211_hdr.
Fix the disconnection by moving skb->data to the correct position
before ieee80211_tx_status_irqsafe().
The problem was observed with RTL8811AU (TP-Link Archer T2U Nano)
and the potential future rtw88_8821au driver. Also tested with
RTL8811CU (Tenda U9).
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/ecbf0601-810d-4609-b8fc-8b0e38d2948d@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17b9f590f6ec2b9f1b12b1db3bf1d181de6b272 upstream.
When changing the interface type we also need to update the bss_num, the
driver private data is searched based on a unique (bss_type, bss_num)
tuple, therefore every time bss_type changes, bss_num must also change.
This fixes for example an issue in which, after the mode changed, a
wireless scan on the changed interface would not finish, leading to
repeated -EBUSY messages to userspace when other scan requests were
sent.
Fixes: c606008b70 ("mwifiex: Properly initialize private structure on interface type changes")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240510110458.15475-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dc836187f7c6f70a82b4521503e9f9f96194581 upstream.
pid_list_fill_irq() runs via irq_work.
When CONFIG_PREEMPT_RT is disabled, it would run in irq_context.
so it shouldn't sleep while memory allocation.
Change gfp flags from GFP_KERNEL to GFP_NOWAIT to prevent sleep in
irq_work.
This change wouldn't impact functionality in practice because the worst-size
is 2K.
Cc: stable@goodmis.org
Fixes: 8d6e90983a ("tracing: Create a sparse bitmask for pid filtering")
Link: https://lore.kernel.org/20240704150226.1359936-1-yeoreum.yun@arm.com
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: levi.yun <yeoreum.yun@arm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8b632e89a101dae349a7b212c1771d7925f441b upstream.
io_uring_cancel_generic() should retry if any state changes like a
request is completed, however in case of a task exit it only goes for
another loop and avoids schedule() if any tracked (i.e. REQ_F_INFLIGHT)
request got completed.
Let's assume we have a non-tracked request executing in iowq and a
tracked request linked to it. Let's also assume
io_uring_cancel_generic() fails to find and cancel the request, i.e.
via io_run_local_work(), which may happen as io-wq has gaps.
Next, the request logically completes, io-wq still hold a ref but queues
it for completion via tw, which happens in
io_uring_try_cancel_requests(). After, right before prepare_to_wait()
io-wq puts the request, grabs the linked one and tries executes it, e.g.
arms polling. Finally the cancellation loop calls prepare_to_wait(),
there are no tw to run, no tracked request was completed, so the
tctx_inflight() check passes and the task is put to indefinite sleep.
Cc: stable@vger.kernel.org
Fixes: 3f48cf18f8 ("io_uring: unify files and task cancel")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/acac7311f4e02ce3c43293f8f1fda9c705d158f1.1721819383.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9ca51596bbfd0f9c386dd1c613c394c78d9e5e6 upstream.
The syzbot constructs a directory that has no dirblock but is non-inline,
i.e. the first directory block is a hole. And no errors are reported when
creating files in this directory in the following flow.
ext4_mknod
...
ext4_add_entry
// Read block 0
ext4_read_dirblock(dir, block, DIRENT)
bh = ext4_bread(NULL, inode, block, 0)
if (!bh && (type == INDEX || type == DIRENT_HTREE))
// The first directory block is a hole
// But type == DIRENT, so no error is reported.
After that, we get a directory block without '.' and '..' but with a valid
dentry. This may cause some code that relies on dot or dotdot (such as
make_indexed_dir()) to crash.
Therefore when ext4_read_dirblock() finds that the first directory block
is a hole report that the filesystem is corrupted and return an error to
avoid loading corrupted data from disk causing something bad.
Reported-by: syzbot+ae688d469e36fb5138d0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ae688d469e36fb5138d0
Fixes: 4e19d6b65f ("ext4: allow directory holes")
Cc: stable@kernel.org
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20240702132349.2600605-3-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50ea741def587a64e08879ce6c6a30131f7111e7 upstream.
Syzbot reports a issue as follows:
============================================
BUG: unable to handle page fault for address: ffffed11022e24fe
PGD 23ffee067 P4D 23ffee067 PUD 0
Oops: Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 PID: 5079 Comm: syz-executor306 Not tainted 6.10.0-rc5-g55027e689933 #0
Call Trace:
<TASK>
make_indexed_dir+0xdaf/0x13c0 fs/ext4/namei.c:2341
ext4_add_entry+0x222a/0x25d0 fs/ext4/namei.c:2451
ext4_rename fs/ext4/namei.c:3936 [inline]
ext4_rename2+0x26e5/0x4370 fs/ext4/namei.c:4214
[...]
============================================
The immediate cause of this problem is that there is only one valid dentry
for the block to be split during do_split, so split==0 results in out of
bounds accesses to the map triggering the issue.
do_split
unsigned split
dx_make_map
count = 1
split = count/2 = 0;
continued = hash2 == map[split - 1].hash;
---> map[4294967295]
The maximum length of a filename is 255 and the minimum block size is 1024,
so it is always guaranteed that the number of entries is greater than or
equal to 2 when do_split() is called.
But syzbot's crafted image has no dot and dotdot in dir, and the dentry
distribution in dirblock is as follows:
bus dentry1 hole dentry2 free
|xx--|xx-------------|...............|xx-------------|...............|
0 12 (8+248)=256 268 256 524 (8+256)=264 788 236 1024
So when renaming dentry1 increases its name_len length by 1, neither hole
nor free is sufficient to hold the new dentry, and make_indexed_dir() is
called.
In make_indexed_dir() it is assumed that the first two entries of the
dirblock must be dot and dotdot, so bus and dentry1 are left in dx_root
because they are treated as dot and dotdot, and only dentry2 is moved
to the new leaf block. That's why count is equal to 1.
Therefore add the ext4_check_dx_root() helper function to add more sanity
checks to dot and dotdot before starting the conversion to avoid the above
issue.
Reported-by: syzbot+ae688d469e36fb5138d0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=ae688d469e36fb5138d0
Fixes: ac27a0ec11 ("[PATCH] ext4: initial copy of files from ext3")
Cc: stable@kernel.org
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20240702132349.2600605-2-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90d4471146de21745980cba51ce88e7926bcc4f upstream.
When the filesystem block bitmap is corrupted, we detect the corruption
while loading the bitmap and fail the allocation with error. However the
next allocation from the same bitmap will notice the bitmap buffer is
already loaded and tries to allocate from the bitmap with mixed results
(depending on the exact nature of the bitmap corruption). Fix the
problem by using BH_verified bit to indicate whether the bitmap is valid
or not.
Reported-by: syzbot+5f682cd029581f9edfd1@syzkaller.appspotmail.com
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/20240617154201.29512-2-jack@suse.cz
Fixes: 1e0d4adf17 ("udf: Check consistency of Space Bitmap Descriptor")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e314e452687ce0ec5874e42cdb993a34325d3d2 upstream.
Although by default we negotiate CIFS Unix Extensions for SMB1 mounts to
Samba (and they work if the user does not specify "unix" or "posix" or
"linux" on mount), and we do properly handle when a user turns them off
with "nounix" mount parm. But with the changes to the mount API we
broke cases where the user explicitly specifies the "unix" option (or
equivalently "linux" or "posix") on mount with vers=1.0 to Samba or other
servers which support the CIFS Unix Extensions.
"mount error(95): Operation not supported"
and logged:
"CIFS: VFS: Check vers= mount option. SMB3.11 disabled but required for POSIX extensions"
even though CIFS Unix Extensions are supported for vers=1.0 This patch fixes
the case where the user specifies both "unix" (or equivalently "posix" or
"linux") and "vers=1.0" on mount to a server which supports the
CIFS Unix Extensions.
Cc: stable@vger.kernel.org
Reviewed-by: David Howells <dhowell@redhat.com>
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
