[ Upstream commit 19c6a63ced ]
snd_pcm_hw_params_set_rate_near can return incorrect sample rate in
some cases, e.g. when the backend output rate is set to some value higher
than 48000 Hz and the input rate is 8000 Hz. So passing the value returned
by snd_pcm_hw_params_set_rate_near to snd_pcm_hw_params will result in
"FSO/FSI ratio error" and playing no audio at all while the userland
is not properly notified about the issue.
If SRC is unable to convert the requested sample rate to the sample rate
the backend is using, then the requested sample rate should be adjusted in
rsnd_hw_params. The userland will be notified about that change in the
returned hw_params structure.
Signed-off-by: Mikhail Durnev <mikhail_durnev@mentor.com>
Link: https://lore.kernel.org/r/1615870055-13954-1-git-send-email-mikhail_durnev@mentor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e127906b68 ]
Commit eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 991b265460 ]
Commit e20f0dbf20 ("net/mlx5e: RX, Add a prefetch command for small
L1_CACHE_BYTES") switched to using net_prefetchw at all places in mlx5e.
In the same time frame, commit 5af75c747e ("net/mlx5e: Enhanced TX
MPWQE for SKBs") added one more usage of prefetchw. When these two
changes were merged, this new occurrence of prefetchw wasn't replaced
with net_prefetchw.
This commit fixes this last occurrence of prefetchw in
mlx5e_tx_mpwqe_session_start, making the same change that was done in
mlx5e_xdp_mpwqe_session_start.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1980d37565 ]
(struct tipc_link_info)->dest is in network order (__be32), so we must
convert the value to network order before assigning. The problem detected
by sparse:
net/tipc/netlink_compat.c:699:24: warning: incorrect type in assignment (different base types)
net/tipc/netlink_compat.c:699:24: expected restricted __be32 [usertype] dest
net/tipc/netlink_compat.c:699:24: got int
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eec054b5a7 ]
This patch fixes the flushing of send work before shutdown. The function
cancel_work_sync() is not the right workqueue functionality to use here
as it would cancel the work if the work queues itself. In cases of
EAGAIN in send() for dlm message we need to be sure that everything is
send out before. The function flush_work() will ensure that every send
work is be done inclusive in EAGAIN cases.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 710176e836 ]
This patch adds an additional check for minimum dlm header size which is
an invalid dlm message and signals a broken stream. A msglen field cannot
be less than the dlm header size because the field is inclusive header
lengths.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c48950b4 ]
This patch fixes the following message which randomly pops up during
glocktop call:
seq_file: buggy .next function table_seq_next did not update position index
The issue is that seq_read_iter() in fs/seq_file.c also needs an
increment of the index in an non next record case as well which this
patch fixes otherwise seq_read_iter() will print out the above message.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e5af36b2ad upstream.
It turns out that there are systems where HWP is enabled during
initialization by the platform firmware (BIOS), but HWP EPP support
is not advertised.
After commit 7aa1031223 ("cpufreq: intel_pstate: Avoid enabling HWP
if EPP is not supported") intel_pstate refuses to use HWP on those
systems, but the fallback PERF_CTL interface does not work on them
either because of enabled HWP, and once enabled, HWP cannot be
disabled. Consequently, the users of those systems cannot control
CPU performance scaling.
Address this issue by making intel_pstate use HWP unconditionally if
it is enabled already when the driver starts.
Fixes: 7aa1031223 ("cpufreq: intel_pstate: Avoid enabling HWP if EPP is not supported")
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.9+ <stable@vger.kernel.org> # 5.9+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c745253e2a upstream.
As pm_runtime_need_not_resume() relies also on usage_count, it can return
a different value in pm_runtime_force_suspend() compared to when called in
pm_runtime_force_resume(). Different return values can happen if anything
calls PM runtime functions in between, and causes the parent child_count
to increase on every resume.
So far I've seen the issue only for omapdrm that does complicated things
with PM runtime calls during system suspend for legacy reasons:
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
pm_runtime_force_suspend() for 58000000.dss, !pm_runtime_need_not_resume()
__update_runtime_status()
system suspended
pm_runtime_force_resume() for 58000000.dss, pm_runtime_need_not_resume()
pm_runtime_enable() only called because of pm_runtime_need_not_resume()
omap_atomic_commit_tail() for omapdrm.0
dispc_runtime_get()
wakes up 58000000.dss as it's the dispc parent
dispc_runtime_resume()
rpm_resume() increases parent child_count
dispc_runtime_put() won't idle, PM runtime suspend blocked
...
rpm_suspend for 58000000.dss but parent child_count is now unbalanced
Let's fix the issue by adding a flag for needs_force_resume and use it in
pm_runtime_force_resume() instead of pm_runtime_need_not_resume().
Additionally omapdrm system suspend could be simplified later on to avoid
lots of unnecessary PM runtime calls and the complexity it adds. The
driver can just use internal functions that are shared between the PM
runtime and system suspend related functions.
Fixes: 4918e1f87c ("PM / runtime: Rework pm_runtime_force_suspend/resume()")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a217a6593c upstream.
In VMX, the host NMI handler needs to be invoked after NMI VM-Exit.
Before commit 1a5488ef0d ("KVM: VMX: Invoke NMI handler via indirect
call instead of INTn"), this was done by INTn ("int $2"). But INTn
microcode is relatively expensive, so the commit reworked NMI VM-Exit
handling to invoke the kernel handler by function call.
But this missed a detail. The NMI entry point for direct invocation is
fetched from the IDT table and called on the kernel stack. But on 64-bit
the NMI entry installed in the IDT expects to be invoked on the IST stack.
It relies on the "NMI executing" variable on the IST stack to work
correctly, which is at a fixed position in the IST stack. When the entry
point is unexpectedly called on the kernel stack, the RSP-addressed "NMI
executing" variable is obviously also on the kernel stack and is
"uninitialized" and can cause the NMI entry code to run in the wrong way.
Provide a non-ist entry point for VMX which shares the C-function with
the regular NMI entry and invoke the new asm entry point instead.
On 32-bit this just maps to the regular NMI entry point as 32-bit has no
ISTs and is not affected.
[ tglx: Made it independent for backporting, massaged changelog ]
Fixes: 1a5488ef0d ("KVM: VMX: Invoke NMI handler via indirect call instead of INTn")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Lai Jiangshan <laijs@linux.alibaba.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87r1imi8i1.ffs@nanos.tec.linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5e2184d15 upstream.
Remove the update_pte() shadow paging logic, which was obsoleted by
commit 4731d4c7a0 ("KVM: MMU: out of sync shadow core"), but never
removed. As pointed out by Yu, KVM never write protects leaf page
tables for the purposes of shadow paging, and instead marks their
associated shadow page as unsync so that the guest can write PTEs at
will.
The update_pte() path, which predates the unsync logic, optimizes COW
scenarios by refreshing leaf SPTEs when they are written, as opposed to
zapping the SPTE, restarting the guest, and installing the new SPTE on
the subsequent fault. Since KVM no longer write-protects leaf page
tables, update_pte() is unreachable and can be dropped.
Reported-by: Yu Zhang <yu.c.zhang@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210115004051.4099250-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1df83992d9 upstream.
If the total number of commands queried through TPM2_CAP_COMMANDS is
different from that queried through TPM2_CC_GET_CAPABILITY, it indicates
an unknown error. In this case, an appropriate error code -EFAULT should
be returned. However, we currently do not explicitly assign this error
code to 'rc'. As a result, 0 was incorrectly returned.
Cc: stable@vger.kernel.org
Fixes: 58472f5cd4f6("tpm: validate TPM 2.0 commands")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83a775d5f9 upstream.
Two error return paths are neglecting to free allocated object td,
causing a memory leak. Fix this by returning via the error return
path that securely kfree's td.
Fixes clang scan-build warning:
security/keys/trusted-keys/trusted_tpm1.c:496:10: warning: Potential
memory leak [unix.Malloc]
Cc: stable@vger.kernel.org
Fixes: 5df16caada ("KEYS: trusted: Fix incorrect handling of tpm_get_random()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34e5b01186 upstream.
As Or Cohen described:
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
This patch is to fix it by moving the auto_asconf init out of
sctp_init_sock(), by which inet_create()/inet6_create() won't
need to operate it in sctp_destroy_sock() when calling
sk_common_release().
It also makes more sense to do auto_asconf init while binding the
first addr, as auto_asconf actually requires an ANY addr bind,
see it in sctp_addr_wq_timeout_handler().
This addresses CVE-2021-23133.
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bfe5e8e4 upstream.
This reverts commit b166a20b07.
This one has to be reverted as it introduced a dead lock, as
syzbot reported:
CPU0 CPU1
---- ----
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
CPU0 is the thread of sctp_addr_wq_timeout_handler(), and CPU1
is that of sctp_close().
The original issue this commit fixed will be fixed in the next
patch.
Reported-by: syzbot+959223586843e69a2674@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1139aeb1c5 upstream.
As of commit 966a967116 ("smp: Avoid using two cache lines for struct
call_single_data"), the smp code prefers 32-byte aligned call_single_data
objects for performance reasons, but the block layer includes an instance
of this structure in the main 'struct request' that is more senstive
to size than to performance here, see 4ccafe0320 ("block: unalign
call_single_data in struct request").
The result is a violation of the calling conventions that clang correctly
points out:
block/blk-mq.c:630:39: warning: passing 8-byte aligned argument to 32-byte aligned parameter 2 of 'smp_call_function_single_async' may result in an unaligned pointer access [-Walign-mismatch]
smp_call_function_single_async(cpu, &rq->csd);
It does seem that the usage of the call_single_data without cache line
alignment should still be allowed by the smp code, so just change the
function prototype so it accepts both, but leave the default alignment
unchanged for the other users. This seems better to me than adding
a local hack to shut up an otherwise correct warning in the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.kernel.org/r/20210505211300.3174456-1-arnd@kernel.org
[nc: Fix conflicts, modify rq_csd_init]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d432592f3 upstream.
tcp_set_default_congestion_control() is netns-safe in that it writes
to &net->ipv4.tcp_congestion_control, but it also sets
ca->flags |= TCP_CONG_NON_RESTRICTED which is not namespaced.
This has the unintended side-effect of changing the global
net.ipv4.tcp_allowed_congestion_control sysctl, despite the fact that it
is read-only: 97684f0970 ("net: Make tcp_allowed_congestion_control
readonly in non-init netns")
Resolve this netns "leak" by only allowing the init netns to set the
default algorithm to one that is restricted. This restriction could be
removed if tcp_allowed_congestion_control were namespace-ified in the
future.
This bug was uncovered with
https://github.com/JonathonReinhart/linux-netns-sysctl-verify
Fixes: 6670e15244 ("tcp: Namespace-ify sysctl_tcp_default_congestion_control")
Signed-off-by: Jonathon Reinhart <jonathon.reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d78050ee35 upstream.
With the introduction of a dynamic ZONE_DMA range based on DT or IORT
information, there's no need for CMA allocations from the wider
ZONE_DMA32 since on most platforms ZONE_DMA will cover the 32-bit
addressable range. Remove the arm64_dma32_phys_limit and set
arm64_dma_phys_limit to cover the smallest DMA range required on the
platform. CMA allocation and crashkernel reservation now go in the
dynamically sized ZONE_DMA, allowing correct functionality on RPi4.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> # On RPi4B
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04ea3086c4 upstream.
Only the very first page of BPF ringbuf that contains consumer position
counter is supposed to be mapped as writeable by user-space. Producer
position is read-only and can be modified only by the kernel code. BPF ringbuf
data pages are read-only as well and are not meant to be modified by
user-code to maintain integrity of per-record headers.
This patch allows to map only consumer position page as writeable and
everything else is restricted to be read-only. remap_vmalloc_range()
internally adds VM_DONTEXPAND, so all the established memory mappings can't be
extended, which prevents any future violations through mremap()'ing.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Ryota Shiga (Flatt Security)
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b81ccebae upstream.
A BPF program might try to reserve a buffer larger than the ringbuf size.
If the consumer pointer is way ahead of the producer, that would be
successfully reserved, allowing the BPF program to read or write out of
the ringbuf allocated area.
Reported-by: Ryota Shiga (Flatt Security)
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 049c4e1371 upstream.
Fix a bug in the verifier's scalar32_min_max_*() functions which leads to
incorrect tracking of 32 bit bounds for the simulation of and/or/xor bitops.
When both the src & dst subreg is a known constant, then the assumption is
that scalar_min_max_*() will take care to update bounds correctly. However,
this is not the case, for example, consider a register R2 which has a tnum
of 0xffffffff00000000, meaning, lower 32 bits are known constant and in this
case of value 0x00000001. R2 is then and'ed with a register R3 which is a
64 bit known constant, here, 0x100000002.
What can be seen in line '10:' is that 32 bit bounds reach an invalid state
where {u,s}32_min_value > {u,s}32_max_value. The reason is scalar32_min_max_*()
delegates 32 bit bounds updates to scalar_min_max_*(), however, that really
only takes place when both the 64 bit src & dst register is a known constant.
Given scalar32_min_max_*() is intended to be designed as closely as possible
to scalar_min_max_*(), update the 32 bit bounds in this situation through
__mark_reg32_known() which will set all {u,s}32_{min,max}_value to the correct
constant, which is 0x00000000 after the fix (given 0x00000001 & 0x00000002 in
32 bit space). This is possible given var32_off already holds the final value
as dst_reg->var_off is updated before calling scalar32_min_max_*().
Before fix, invalid tracking of R2:
[...]
9: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=-9223372036854775807 (0x8000000000000001),smax_value=9223372032559808513 (0x7fffffff00000001),umin_value=1,umax_value=0xffffffff00000001,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_min_value=1,u32_max_value=1) R3_w=inv4294967298 R10=fp0
9: (5f) r2 &= r3
10: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=0,smax_value=4294967296 (0x100000000),umin_value=0,umax_value=0x100000000,var_off=(0x0; 0x100000000),s32_min_value=1,s32_max_value=0,u32_min_value=1,u32_max_value=0) R3_w=inv4294967298 R10=fp0
[...]
After fix, correct tracking of R2:
[...]
9: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=-9223372036854775807 (0x8000000000000001),smax_value=9223372032559808513 (0x7fffffff00000001),umin_value=1,umax_value=0xffffffff00000001,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_min_value=1,u32_max_value=1) R3_w=inv4294967298 R10=fp0
9: (5f) r2 &= r3
10: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,smin_value=0,smax_value=4294967296 (0x100000000),umin_value=0,umax_value=0x100000000,var_off=(0x0; 0x100000000),s32_min_value=0,s32_max_value=0,u32_min_value=0,u32_max_value=0) R3_w=inv4294967298 R10=fp0
[...]
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Fixes: 2921c90d47 ("bpf: Fix a verifier failure with xor")
Reported-by: Manfred Paul (@_manfp)
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22650f1481 ]
The generic/464 xfstest causes kAFS to emit occasional warnings of the
form:
kAFS: vnode modified {100055:8a} 30->31 YFS.StoreData64 (c=6015)
This indicates that the data version received back from the server did not
match the expected value (the DV should be incremented monotonically for
each individual modification op committed to a vnode).
What is happening is that a lookup call is doing a bulk status fetch
speculatively on a bunch of vnodes in a directory besides getting the
status of the vnode it's actually interested in. This is racing with a
StoreData operation (though it could also occur with, say, a MakeDir op).
On the client, a modification operation locks the vnode, but the bulk
status fetch only locks the parent directory, so no ordering is imposed
there (thereby avoiding an avenue to deadlock).
On the server, the StoreData op handler doesn't lock the vnode until it's
received all the request data, and downgrades the lock after committing the
data until it has finished sending change notifications to other clients -
which allows the status fetch to occur before it has finished.
This means that:
- a status fetch can access the target vnode either side of the exclusive
section of the modification
- the status fetch could start before the modification, yet finish after,
and vice-versa.
- the status fetch and the modification RPCs can complete in either order.
- the status fetch can return either the before or the after DV from the
modification.
- the status fetch might regress the locally cached DV.
Some of these are handled by the previous fix[1], but that's not sufficient
because it checks the DV it received against the DV it cached at the start
of the op, but the DV might've been updated in the meantime by a locally
generated modification op.
Fix this by the following means:
(1) Keep track of when we're performing a modification operation on a
vnode. This is done by marking vnode parameters with a 'modification'
note that causes the AFS_VNODE_MODIFYING flag to be set on the vnode
for the duration.
(2) Alter the speculation race detection to ignore speculative status
fetches if either the vnode is marked as being modified or the data
version number is not what we expected.
Note that whilst the "vnode modified" warning does get recovered from as it
causes the client to refetch the status at the next opportunity, it will
also invalidate the pagecache, so changes might get lost.
Fixes: a9e5c87ca7 ("afs: Fix speculative status fetch going out of order wrt to modifications")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-and-reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/160605082531.252452.14708077925602709042.stgit@warthog.procyon.org.uk/ [1]
Link: https://lore.kernel.org/linux-fsdevel/161961335926.39335.2552653972195467566.stgit@warthog.procyon.org.uk/ # v1
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f38f03ae8 ]
Patch series "Use obj_cgroup APIs to charge kmem pages", v5.
Since Roman's series "The new cgroup slab memory controller" applied.
All slab objects are charged with the new APIs of obj_cgroup. The new
APIs introduce a struct obj_cgroup to charge slab objects. It prevents
long-living objects from pinning the original memory cgroup in the
memory. But there are still some corner objects (e.g. allocations
larger than order-1 page on SLUB) which are not charged with the new
APIs. Those objects (include the pages which are allocated from buddy
allocator directly) are charged as kmem pages which still hold a
reference to the memory cgroup.
E.g. We know that the kernel stack is charged as kmem pages because the
size of the kernel stack can be greater than 2 pages (e.g. 16KB on
x86_64 or arm64). If we create a thread (suppose the thread stack is
charged to memory cgroup A) and then move it from memory cgroup A to
memory cgroup B. Because the kernel stack of the thread hold a
reference to the memory cgroup A. The thread can pin the memory cgroup
A in the memory even if we remove the cgroup A. If we want to see this
scenario by using the following script. We can see that the system has
added 500 dying cgroups (This is not a real world issue, just a script
to show that the large kmallocs are charged as kmem pages which can pin
the memory cgroup in the memory).
#!/bin/bash
cat /proc/cgroups | grep memory
cd /sys/fs/cgroup/memory
echo 1 > memory.move_charge_at_immigrate
for i in range{1..500}
do
mkdir kmem_test
echo $$ > kmem_test/cgroup.procs
sleep 3600 &
echo $$ > cgroup.procs
echo `cat kmem_test/cgroup.procs` > cgroup.procs
rmdir kmem_test
done
cat /proc/cgroups | grep memory
This patchset aims to make those kmem pages to drop the reference to
memory cgroup by using the APIs of obj_cgroup. Finally, we can see that
the number of the dying cgroups will not increase if we run the above test
script.
This patch (of 7):
The rcu_read_lock/unlock only can guarantee that the memcg will not be
freed, but it cannot guarantee the success of css_get (which is in the
refill_stock when cached memcg changed) to memcg.
rcu_read_lock()
memcg = obj_cgroup_memcg(old)
__memcg_kmem_uncharge(memcg)
refill_stock(memcg)
if (stock->cached != memcg)
// css_get can change the ref counter from 0 back to 1.
css_get(&memcg->css)
rcu_read_unlock()
This fix is very like the commit:
eefbfa7fd6 ("mm: memcg/slab: fix use after free in obj_cgroup_charge")
Fix this by holding a reference to the memcg which is passed to the
__memcg_kmem_uncharge() before calling __memcg_kmem_uncharge().
Link: https://lkml.kernel.org/r/20210319163821.20704-1-songmuchun@bytedance.com
Link: https://lkml.kernel.org/r/20210319163821.20704-2-songmuchun@bytedance.com
Fixes: 3de7d4f25a ("mm: memcg/slab: optimize objcg stock draining")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 926ee00ea2 ]
The intent with this code was to return negative error codes but instead
it returns positives.
The problem is how type promotion works with ternary operations. These
functions return long, "ret" is an int and "copied" is a u32. The
negative error code is first cast to u32 so it becomes a high positive and
then cast to long where it's still a positive.
We could fix this by declaring "ret" as a ssize_t but let's just get rid
of the ternaries instead.
Link: https://lkml.kernel.org/r/YIE+/cK1tBzSuQPU@mwanda
Fixes: 5bf2b19320 ("kfifo: add example files to the kernel sample directory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3db00b79d ]
When enabled local debugging via `#define EFI_DEBUG 1` noticed build
failure:
arch/ia64/kernel/efi.c:564:8: error: 'i' undeclared (first use in this function)
While at it fixed benign string format mismatches visible only when
EFI_DEBUG is enabled:
arch/ia64/kernel/efi.c:589:11:
warning: format '%lx' expects argument of type 'long unsigned int',
but argument 5 has type 'u64' {aka 'long long unsigned int'} [-Wformat=]
Link: https://lkml.kernel.org/r/20210328212246.685601-1-slyfox@gentoo.org
Fixes: 14fb420909 ("efi: Merge EFI system table revision and vendor checks")
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7525858679 ]
In digital_tg_recv_dep_req, it calls nfc_tm_data_received(..,resp).
If nfc_tm_data_received() failed, the callee will free the resp via
kfree_skb() and return error. But in the exit branch, the resp
will be freed again.
My patch sets resp to NULL if nfc_tm_data_received() failed, to
avoid the double free.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9901408815 ]
The IPv6 Multicast Router Advertisements parsing has the following two
issues:
For one thing, ICMPv6 MRD Advertisements are smaller than ICMPv6 MLD
messages (ICMPv6 MRD Adv.: 8 bytes vs. ICMPv6 MLDv1/2: >= 24 bytes,
assuming MLDv2 Reports with at least one multicast address entry).
When ipv6_mc_check_mld_msg() tries to parse an Multicast Router
Advertisement its MLD length check will fail - and it will wrongly
return -EINVAL, even if we have a valid MRD Advertisement. With the
returned -EINVAL the bridge code will assume a broken packet and will
wrongly discard it, potentially leading to multicast packet loss towards
multicast routers.
The second issue is the MRD header parsing in
br_ip6_multicast_mrd_rcv(): It wrongly checks for an ICMPv6 header
immediately after the IPv6 header (IPv6 next header type). However
according to RFC4286, section 2 all MRD messages contain a Router Alert
option (just like MLD). So instead there is an IPv6 Hop-by-Hop option
for the Router Alert between the IPv6 and ICMPv6 header, again leading
to the bridge wrongly discarding Multicast Router Advertisements.
To fix these two issues, introduce a new return value -ENODATA to
ipv6_mc_check_mld() to indicate a valid ICMPv6 packet with a hop-by-hop
option which is not an MLD but potentially an MRD packet. This also
simplifies further parsing in the bridge code, as ipv6_mc_check_mld()
already fully checks the ICMPv6 header and hop-by-hop option.
These issues were found and fixed with the help of the mrdisc tool
(https://github.com/troglobit/mrdisc).
Fixes: 4b3087c7e3 ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34b39efa5a ]
In bnxt_qplib_alloc_res, it calls bnxt_qplib_alloc_dpi_tbl(). Inside
bnxt_qplib_alloc_dpi_tbl, dpit->dbr_bar_reg_iomem is freed via
pci_iounmap() in unmap_io error branch. After the callee returns err code,
bnxt_qplib_alloc_res calls
bnxt_qplib_free_res()->bnxt_qplib_free_dpi_tbl() in the fail branch. Then
dpit->dbr_bar_reg_iomem is freed in the second time by pci_iounmap().
My patch set dpit->dbr_bar_reg_iomem to NULL after it is freed by
pci_iounmap() in the first time, to avoid the double free.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/20210426140614.6722-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3093ee182f ]
Our code analyzer reported a UAF.
In siw_alloc_mr(), it calls siw_mr_add_mem(mr,..). In the implementation of
siw_mr_add_mem(), mem is assigned to mr->mem and then mem is freed via
kfree(mem) if xa_alloc_cyclic() failed. Here, mr->mem still point to a
freed object. After, the execution continue up to the err_out branch of
siw_alloc_mr, and the freed mr->mem is used in siw_mr_drop_mem(mr).
My patch moves "mr->mem = mem" behind the if (xa_alloc_cyclic(..)<0) {}
section, to avoid the uaf.
Fixes: 2251334dca ("rdma/siw: application buffer management")
Link: https://lore.kernel.org/r/20210426011647.3561-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Bernard Metzler <bmt@zurich.ihm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10bf4e8316 ]
Similarly as b02709587e ("bpf: Fix propagation of 32-bit signed bounds
from 64-bit bounds."), we also need to fix the propagation of 32 bit
unsigned bounds from 64 bit counterparts. That is, really only set the
u32_{min,max}_value when /both/ {umin,umax}_value safely fit in 32 bit
space. For example, the register with a umin_value == 1 does /not/ imply
that u32_min_value is also equal to 1, since umax_value could be much
larger than 32 bit subregister can hold, and thus u32_min_value is in
the interval [0,1] instead.
Before fix, invalid tracking result of R2_w=inv1:
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smin_value=-9223372036854775807,smax_value=9223372032559808513,umin_value=1,umax_value=18446744069414584321,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv1 R10=fp0
[...]
After fix, correct tracking result of R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)):
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smax_value=9223372032559808513,umax_value=18446744069414584321,var_off=(0x0; 0xffffffff00000001),s32_min_value=0,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)) R10=fp0
[...]
Thus, same issue as in b02709587e holds for unsigned subregister tracking.
Also, align __reg64_bound_u32() similarly to __reg64_bound_s32() as done in
b02709587e to make them uniform again.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Manfred Paul (@_manfp)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bede0ebf0b ]
Fix failed tests checks in core_reloc test runner, which allowed failing tests
to pass quietly. Also add extra check to make sure that expected to fail test cases with
invalid names are caught as test failure anyway, as this is not an expected
failure mode. Also fix mislabeled probed vs direct bitfield test cases.
Fixes: 124a892d1c ("selftests/bpf: Test TYPE_EXISTS and TYPE_SIZE CO-RE relocations")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210426192949.416837-6-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a30eb2392 ]
Negative field existence cases for have a broken assumption that FIELD_EXISTS
CO-RE relo will fail for fields that match the name but have incompatible type
signature. That's not how CO-RE relocations generally behave. Types and fields
that match by name but not by expected type are treated as non-matching
candidates and are skipped. Error later is reported if no matching candidate
was found. That's what happens for most relocations, but existence relocations
(FIELD_EXISTS and TYPE_EXISTS) are more permissive and they are designed to
return 0 or 1, depending if a match is found. This allows to handle
name-conflicting but incompatible types in BPF code easily. Combined with
___flavor suffixes, it's possible to handle pretty much any structural type
changes in kernel within the compiled once BPF source code.
So, long story short, negative field existence test cases are invalid in their
assumptions, so this patch reworks them into a single consolidated positive
case that doesn't match any of the fields.
Fixes: c7566a6969 ("selftests/bpf: Add field existence CO-RE relocs tests")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210426192949.416837-5-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d72e7c767 ]
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbdd096a5a ]
Disable pass-through of the FS and GS base MSRs for 32-bit KVM. Intel's
SDM unequivocally states that the MSRs exist if and only if the CPU
supports x86-64. FS_BASE and GS_BASE are mostly a non-issue; a clever
guest could opportunistically use the MSRs without issue. KERNEL_GS_BASE
is a bigger problem, as a clever guest would subtly be broken if it were
migrated, as KVM disallows software access to the MSRs, and unlike the
direct variants, KERNEL_GS_BASE needs to be explicitly migrated as it's
not captured in the VMCS.
Fixes: 25c5f225be ("KVM: VMX: Enable MSR Bitmap feature")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422023831.3473491-1-seanjc@google.com>
[*NOT* for stable kernels. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
