[ Upstream commit fa09fa6038 ]
The SPDIFRX block is clocked by 2 clocks: peripheral and generic clocks.
Peripheral clock feeds user interface (registers) and generic clock feeds
the receiver.
To enable the receiver the generic clock needs to be enabled and also the
ENABLE bit of MCHP_SPDIFRX_MR register need to be set.
The signal control exported by mchp-spdifrx driver reports wrong status
when the receiver is disabled. This can happen when requesting the signal
and the capture was not previously started. To solve this the receiver
needs to be enabled (by enabling generic clock and setting ENABLE bit of
MR register) before reading the signal status.
As with this fix there are 2 paths now that need to control the generic
clock and ENABLE bit of SPDIFRX_MR register (one path though controls, one
path though configuration) a mutex has been introduced. We can't rely on
subsystem locking as the controls are protected by
struct snd_card::controls_rwsem semaphore and configuration is protected
by a different lock (embedded in snd_pcm_stream_lock_irq()).
The introduction of mutex is also extended to other controls which rely on
SPDIFRX_RSR.ULOCK bit as it has been discovered experimentally that having
both clocks enabled but not the receiver (through ENABLE bit of SPDIFRX.MR)
leads to inconsistent values of SPDIFRX_RSR.ULOCK. Thus on some controls we
rely on software state (dev->trigger_enabled protected by mutex) to
retrieve proper values.
Fixes: ef265c55c1 ("ASoC: mchp-spdifrx: add driver for SPDIF RX")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230130120647.638049-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bde04318 ]
Selecting a symbol with additional dependencies requires
adding the same dependency here:
WARNING: unmet direct dependencies detected for MUX_MMIO
Depends on [n]: MULTIPLEXER [=y] && OF [=n]
Selected by [y]:
- SPI_DW_BT1 [=y] && SPI [=y] && SPI_MASTER [=y] && SPI_DESIGNWARE [=y] && (MIPS_BAIKAL_T1 || COMPILE_TEST [=y])
Drop the 'select' here to avoid the problem. Anyone using
the dw-bt1 SPI driver should make sure they include the
mux driver as well now.
Fixes: 7218838109 ("spi: dw-bt1: Fix undefined devm_mux_control_get symbol")
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Link: https://lore.kernel.org/all/20221218192523.c6vnfo26ua6xqf26@mobilestation/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230130140156.3620863-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91aeaed2c1 ]
According to Figure 16 Turnaround Procedure on page 36 in [1], you
can see the status of LP-00 -> LP10 -> LP11. This state can correspond
to the state of DSI from LP00 -> LP11 in mtk_dsi_lane_ready function
in mtk_dsi.c.
LP-00 -> LP10 -> LP11 takes about 2*TLPX time (refer to [1] page 51
to see that TLPX is 50ns)
The delay at the end of the mtk_dsi_lane_ready function should be
greater than the 2*TLPX specified by the DSI spec, and less than
the time specified by the DSI_RX (generally 6ms to 40ms), to avoid
problems caused by the RX specification
[1]:mipi_D-PHY_specification_v1-1
Fixes: 39e8d062b0 ("drm/mediatek: Keep dsi as LP00 before dcs cmds transfer")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1673330093-6771-2-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb258cc1fd ]
The code to write the syncpoint channel assignment register
incorrectly skips the write if hypervisor registers are not available.
The register, however, is within the guest aperture so remove the
check and assign syncpoints properly even on virtualized systems.
Fixes: c3f52220f2 ("gpu: host1x: Enable Tegra186 syncpoint protection")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9d27c6be5 ]
The MIPI DCS specification demands that brightness values are sent in
big endian byte order. It also states that one parameter (i.e. one byte)
shall be sent/received for 8 bit wide values, and two parameters shall
be used for values that are between 9 and 16 bits wide.
Add new functions to properly handle 16-bit brightness in big endian,
since the two 8- and 16-bit cases are distinct from each other.
[richard: use separate functions instead of switch/case]
[richard: split into 16-bit component]
Fixes: 1a9d759331 ("drm/dsi: Implement DCS set/get display brightness")
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Link: 754affd62d
[richard: fix 16-bit brightness_get]
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116224909.23884-2-mailingradian@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abc40122d9 ]
In the event that the topology requests resources that have not been
created by the system (because they are typically not represented in
dpu_mdss_cfg ^1), the resource(s) in global_state (in this case DSC
blocks, until their allocation/assignment is being sanity-checked in
"drm/msm/dpu: Reject topologies for which no DSC blocks are available")
remain NULL but will still be returned out of
dpu_rm_get_assigned_resources, where the caller expects to get an array
containing num_blks valid pointers (but instead gets these NULLs).
To prevent this from happening, where null-pointer dereferences
typically result in a hard-to-debug platform lockup, num_blks shouldn't
increase past NULL blocks and will print an error and break instead.
After all, max_blks represents the static size of the maximum number of
blocks whereas the actual amount varies per platform.
^1: which can happen after a git rebase ended up moving additions to
_dpu_cfg to a different struct which has the same patch context.
Fixes: bb00a452d6 ("drm/msm/dpu: Refactor resource manager")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/517636/
Link: https://lore.kernel.org/r/20230109231556.344977-1-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ee0fe7fa3 ]
Although the "dma_chan" pointer occupies more or equal space compared
to "*dma_chan", the allocation size should use the size of variable
itself.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 01ef7dbffb ("ALSA: hda - Update CA0132 codec to load DSP firmware binary")
Signed-off-by: Alexey V. Vissarionov <gremlin@altlinux.org>
Link: https://lore.kernel.org/r/20230117111522.GA15213@altlinux.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df993fced2 ]
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
Fixes: c54619b0bf ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-2-1f8e0770798b@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fe2a8f40c ]
A null-ptr-deref is triggered when it tries to destroy the workqueue in
vkms->output.composer_workq in vkms_release().
KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f]
CPU: 5 PID: 17193 Comm: modprobe Not tainted 6.0.0-11331-gd465bff130bf #24
RIP: 0010:destroy_workqueue+0x2f/0x710
...
Call Trace:
<TASK>
? vkms_config_debugfs_init+0x50/0x50 [vkms]
__devm_drm_dev_alloc+0x15a/0x1c0 [drm]
vkms_init+0x245/0x1000 [vkms]
do_one_initcall+0xd0/0x4f0
do_init_module+0x1a4/0x680
load_module+0x6249/0x7110
__do_sys_finit_module+0x140/0x200
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The reason is that an OOM happened which triggers the destroy of the
workqueue, however, the workqueue is alloced in the later process,
thus a null-ptr-deref happened. A simple call graph is shown as below:
vkms_init()
vkms_create()
devm_drm_dev_alloc()
__devm_drm_dev_alloc()
devm_drm_dev_init()
devm_add_action_or_reset()
devm_add_action() # an error happened
devm_drm_dev_init_release()
drm_dev_put()
kref_put()
drm_dev_release()
vkms_release()
destroy_workqueue() # null-ptr-deref happened
vkms_modeset_init()
vkms_output_init()
vkms_crtc_init() # where the workqueue get allocated
Fix this by checking if composer_workq is NULL before passing it to
the destroy_workqueue() in vkms_release().
Fixes: 6c234fe37c ("drm/vkms: Implement CRC debugfs API")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221101065156.41584-3-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ecff954c3 ]
A problem about insmod megachips-stdpxxxx-ge-b850v3-fw.ko failed is
triggered with the following log given:
[ 4497.981497] Error: Driver 'stdp4028-ge-b850v3-fw' is already registered, aborting...
insmod: ERROR: could not insert module megachips-stdpxxxx-ge-b850v3-fw.ko: Device or resource busy
The reason is that stdpxxxx_ge_b850v3_init() returns i2c_add_driver()
directly without checking its return value, if i2c_add_driver() failed,
it returns without calling i2c_del_driver() on the previous i2c driver,
resulting the megachips-stdpxxxx-ge-b850v3-fw can never be installed
later.
A simple call graph is shown as below:
stdpxxxx_ge_b850v3_init()
i2c_add_driver(&stdp4028_ge_b850v3_fw_driver)
i2c_add_driver(&stdp2690_ge_b850v3_fw_driver)
i2c_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without delete stdp4028_ge_b850v3_fw_driver
Fix by calling i2c_del_driver() on stdp4028_ge_b850v3_fw_driver when
i2c_add_driver() returns error.
Fixes: fcfa0ddc18 ("drm/bridge: Drivers for megachips-stdpxxxx-ge-b850v3-fw (LVDS-DP++)")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221108091226.114524-1-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6fb6c979ca ]
As of commit eae06120f1 ("drm: refuse ADDFB2 ioctl for broken
bigendian drivers"), drivers must set the
quirk_addfb_prefer_host_byte_order quirk to make the drm_mode_addfb()
compat code work correctly on big-endian machines.
While that works fine for big-endian XRGB8888 and ARGB8888, which are
mapped to the existing little-endian BGRX8888 and BGRA8888 formats, it
does not work for big-endian XRGB1555 and RGB565, as the latter are not
listed in the format database.
Fix this by adding the missing formats. Limit this to big-endian
platforms, as there is currently no need to support these formats on
little-endian platforms.
Fixes: 6960e6da9c ("drm: fix drm_mode_addfb() on big endian machines.")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/3ee1f8144feb96c28742b22384189f1f83bcfc1a.1669221671.git.geert@linux-m68k.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 834c23e4f7 ]
drmm_mode_config_init() will call drm_mode_create_standard_properties()
and won't check the ret value. When drm_mode_create_standard_properties()
failed due to alloc, property will be a NULL pointer and may causes the
null-ptr-deref. Fix the null-ptr-deref by adding the ret value check.
Found null-ptr-deref while testing insert module bochs:
general protection fault, probably for non-canonical address
0xdffffc000000000c: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067]
CPU: 3 PID: 249 Comm: modprobe Not tainted 6.1.0-rc1+ #364
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
RIP: 0010:drm_object_attach_property+0x73/0x3c0 [drm]
Call Trace:
<TASK>
__drm_connector_init+0xb6c/0x1100 [drm]
bochs_pci_probe.cold.11+0x4cb/0x7fe [bochs]
pci_device_probe+0x17d/0x340
really_probe+0x1db/0x5d0
__driver_probe_device+0x1e7/0x250
driver_probe_device+0x4a/0x120
__driver_attach+0xcd/0x2c0
bus_for_each_dev+0x11a/0x1b0
bus_add_driver+0x3d7/0x500
driver_register+0x18e/0x320
do_one_initcall+0xc4/0x3e0
do_init_module+0x1b4/0x630
load_module+0x5dca/0x7230
__do_sys_finit_module+0x100/0x170
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7ff65af9f839
Fixes: 6b4959f43a ("drm/atomic: atomic plane properties")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118021651.2460-1-shangxiaojing@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f922c7b1c1 ]
When devlink instance is put into network namespace and that network
namespace gets deleted, devlink instance is moved back into init_ns.
This is done as a part of cleanup_net() routine. Since cleanup_net()
is called asynchronously from workqueue, there is no guarantee that
the devlink instance move is done after "ip netns del" returns.
So fix this race by making sure that the devlink instance is present
before any other operation.
Reported-by: Amir Tzin <amirtz@nvidia.com>
Fixes: b74c37fd35 ("selftests: netdevsim: add tests for devlink reload with resources")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230220132336.198597-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b60417a9f2 ]
Usage of `set -e` before executing a command causes immediate exit
on failure, without cleanup up the resources allocated at setup.
This can affect the next tests that use the same resources,
leading to a chain of failures.
A simple fix is to always call cleanup function when the script exists.
This approach is already used by other existing tests.
Fixes: 1056691b26 ("selftests: fib_tests: Make test results more verbose")
Signed-off-by: Roxana Nicolescu <roxana.nicolescu@canonical.com>
Link: https://lore.kernel.org/r/20230220110400.26737-2-roxana.nicolescu@canonical.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7515af9fb ]
When the bcmgenet_mii_config() code was refactored it was missed
that the LED control for the MoCA interface got overwritten by
the port_ctrl value. Its previous programming is restored here.
Fixes: 4f8d81b77e ("net: bcmgenet: Refactor register access in bcmgenet_mii_config")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
