[ Upstream commit 9d47e01b9d ]
ADP5061_CHG_STATUS_1_CHG_STATUS is masked with 0x07, which means a length
of 8, but adp5061_chg_type array size is 4, may end up reading 4 elements
beyond the end of the adp5061_chg_type[] array.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1de7c3cf48 ]
syzbot reported hung task [1]. The following program is a simplified
version of the reproducer:
int main(void)
{
int sv[2], fd;
if (socketpair(AF_UNIX, SOCK_STREAM, 0, sv) < 0)
return 1;
if ((fd = open("/dev/nbd0", 0)) < 0)
return 1;
if (ioctl(fd, NBD_SET_SIZE_BLOCKS, 0x81) < 0)
return 1;
if (ioctl(fd, NBD_SET_SOCK, sv[0]) < 0)
return 1;
if (ioctl(fd, NBD_DO_IT) < 0)
return 1;
return 0;
}
When signal interrupt nbd_start_device_ioctl() waiting the condition
atomic_read(&config->recv_threads) == 0, the task can hung because it
waits the completion of the inflight IOs.
This patch fixes the issue by clearing queue, not just shutdown, when
signal interrupt nbd_start_device_ioctl().
Link: https://syzkaller.appspot.com/bug?id=7d89a3ffacd2b83fdd39549bc4d8e0a89ef21239 [1]
Reported-by: syzbot+38e6c55d4969a14c1534@syzkaller.appspotmail.com
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20220907163502.577561-1-syoshida@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30eaf02149 ]
The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20220826142030.213805-1-quanyang.wang@windriver.com
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b064d9144 ]
When the driver calls cx88_risc_buffer() to prepare the buffer, the
function call may fail, resulting in a empty buffer and null-ptr-deref
later in buffer_queue().
The following log can reveal it:
[ 41.822762] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN PTI
[ 41.824488] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 41.828027] RIP: 0010:buffer_queue+0xc2/0x500
[ 41.836311] Call Trace:
[ 41.836945] __enqueue_in_driver+0x141/0x360
[ 41.837262] vb2_start_streaming+0x62/0x4a0
[ 41.838216] vb2_core_streamon+0x1da/0x2c0
[ 41.838516] __vb2_init_fileio+0x981/0xbc0
[ 41.839141] __vb2_perform_fileio+0xbf9/0x1120
[ 41.840072] vb2_fop_read+0x20e/0x400
[ 41.840346] v4l2_read+0x215/0x290
[ 41.840603] vfs_read+0x162/0x4c0
Fix this by checking the return value of cx88_risc_buffer()
[hverkuil: fix coding style issues]
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9eab5f0bb ]
[BUG]
The following script shows that, although scrub can detect super block
errors, it never tries to fix it:
mkfs.btrfs -f -d raid1 -m raid1 $dev1 $dev2
xfs_io -c "pwrite 67108864 4k" $dev2
mount $dev1 $mnt
btrfs scrub start -B $dev2
btrfs scrub start -Br $dev2
umount $mnt
The first scrub reports the super error correctly:
scrub done for f3289218-abd3-41ac-a630-202f766c0859
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
But the second read-only scrub still reports the same super error:
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
[CAUSE]
The comments already shows that super block can be easily fixed by
committing a transaction:
/*
* If we find an error in a super block, we just report it.
* They will get written with the next transaction commit
* anyway
*/
But the truth is, such assumption is not always true, and since scrub
should try to repair every error it found (except for read-only scrub),
we should really actively commit a transaction to fix this.
[FIX]
Just commit a transaction if we found any super block errors, after
everything else is done.
We cannot do this just after scrub_supers(), as
btrfs_commit_transaction() will try to pause and wait for the running
scrub, thus we can not call it with scrub_lock hold.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6effe295e1 ]
This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c152c2f66 ]
When arm64 signal context data overflows the base struct sigcontext it gets
placed in an extra buffer pointed to by a record of type EXTRA_CONTEXT in
the base struct sigcontext which is required to be the last record in the
base struct sigframe. The current validation code attempts to check this
by using GET_RESV_NEXT_HEAD() to step forward from the current record to
the next but that is a macro which assumes it is being provided with a
struct _aarch64_ctx and uses the size there to skip forward to the next
record. Instead validate_extra_context() passes it a struct extra_context
which has a separate size field. This compiles but results in us trying
to validate a termination record in completely the wrong place, at best
failing validation and at worst just segfaulting. Fix this by passing
the struct _aarch64_ctx we meant to into the macro.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220829160703.874492-4-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415432c008 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7492a83ed9 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c9213a1d ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088fe52374 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5848b9563 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11d083c5d ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7c4ebe2f9 ]
Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1 - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97d8d6f075 ]
[why]
Only a single VLINE interrupt is available so interface should not
expose the second one which is used by DMU firmware.
[how]
Remove references to periodic_interrupt1 and VLINE1 from DC interfaces.
Reviewed-by: Jaehyun Chung <jaehyun.chung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b4d8db657 ]
The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)
The problem is with DP PHY compliance setup as follow:
[DPTX + on board LTTPR]------Main Link--->[Scope]
^ |
| |
| |
----------Aux Ch------>[Aux Emulator]
At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.
The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow
igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2
OR
printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc
seek=$((0x100))
This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.
As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."
In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.
The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET
[1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance
[2]: Configuring UnigrafDPTC Controller - Automation Test Sequence
https://www.keysight.com/us/en/assets/9922-01244/help-files/
D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Or Cochvi <or.cochvi@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a2565272a ]
On a MSI S270 with Fedora 37 x86_64 / systemd-251.4 the module does not
properly autoload.
This is likely caused by issues with how systemd-udevd handles the single
quote char (') which is part of the sys_vendor / chassis_vendor strings
on this laptop. As a workaround remove the single quote char + everything
behind it from the sys_vendor + chassis_vendor matches. This fixes
the module not autoloading.
Link: https://github.com/systemd/systemd/issues/24715
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220917210407.647432-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8edd2752b0 ]
cros_ec_handle_event in the cros_ec driver can notify the PM of wake
events. When a device is suspended, cros_ec_handle_event will not check
MKBP events. Instead, received MKBP events are checked during resume by
cros_ec_report_events_during_suspend. But
cros_ec_report_events_during_suspend cannot notify the PM if received
events are wake events, causing wake events to not be reported if
received while the device is suspended.
Update cros_ec_report_events_during_suspend to notify the PM of wake
events during resume by calling pm_wakeup_event.
Signed-off-by: Jameson Thies <jthies@google.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220913204954.2931042-1-jthies@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da09daf881 ]
There are two events that signal a real change of the link state: HPD going
high means the sink is newly connected or wants the source to re-read the
EDID, RX sense going low is a indication that the link has been disconnected.
Ignore the other two events that also trigger interrupts, but don't need
immediate attention: HPD going low does not necessarily mean the link has
been lost and should not trigger a immediate read of the status. RX sense
going high also does not require a detect cycle, as HPD going high is the
right point in time to read the EDID.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1)
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826185733.3213248-1-l.stach@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ae0632d17 ]
The definition of MIN_I64 in bw_fixed.c can cause gcc to whinge about
integer overflow, because it is treated as a positive value, which is
then negated. The temporary positive value is not necessarily
representable.
This causes the following warning:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dml/calcs/bw_fixed.c:30:19:
warning: integer overflow in expression ‘-9223372036854775808’ of type
‘long long int’ results in ‘-9223372036854775808’ [-Woverflow]
30 | (int64_t)(-(1LL << 63))
| ^
Writing out (-MAX_I64 - 1) works instead.
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dc3471d1 ]
The strlen() function returns a size_t which is an unsigned int on 32-bit
arches and an unsigned long on 64-bit arches. But in the drm_copy_field()
function, the strlen() return value is assigned to an 'int len' variable.
Later, the len variable is passed as copy_from_user() third argument that
is an unsigned long parameter as well.
In theory, this can lead to an integer overflow via type conversion. Since
the assignment happens to a signed int lvalue instead of a size_t lvalue.
In practice though, that's unlikely since the values copied are set by DRM
drivers and not controlled by userspace. But using a size_t for len is the
correct thing to do anyways.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220705100215.572498-2-javierm@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d2cb3066f ]
syzbot is reporting cancel_delayed_work() without INIT_DELAYED_WORK() at
l2cap_chan_del() [1], for CONF_NOT_COMPLETE flag (which meant to prevent
l2cap_chan_del() from calling cancel_delayed_work()) is cleared by timer
which fires before l2cap_chan_del() is called by closing file descriptor
created by socket(AF_BLUETOOTH, SOCK_STREAM, BTPROTO_L2CAP).
l2cap_bredr_sig_cmd(L2CAP_CONF_REQ) and l2cap_bredr_sig_cmd(L2CAP_CONF_RSP)
are calling l2cap_ertm_init(chan), and they call l2cap_chan_ready() (which
clears CONF_NOT_COMPLETE flag) only when l2cap_ertm_init(chan) succeeded.
l2cap_sock_init() does not call l2cap_ertm_init(chan), and it instead sets
CONF_NOT_COMPLETE flag by calling l2cap_chan_set_defaults(). However, when
connect() is requested, "command 0x0409 tx timeout" happens after 2 seconds
from connect() request, and CONF_NOT_COMPLETE flag is cleared after 4
seconds from connect() request, for l2cap_conn_start() from
l2cap_info_timeout() callback scheduled by
schedule_delayed_work(&conn->info_timer, L2CAP_INFO_TIMEOUT);
in l2cap_connect() is calling l2cap_chan_ready().
Fix this problem by initializing delayed works used by L2CAP_MODE_ERTM
mode as soon as l2cap_chan_create() allocates a channel, like I did in
commit be85972393 ("Bluetooth: initialize skb_queue_head at
l2cap_chan_create()").
Link: https://syzkaller.appspot.com/bug?extid=83672956c7aa6af698b3 [1]
Reported-by: syzbot <syzbot+83672956c7aa6af698b3@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a04d2fc70 ]
Currently if ipcomp_alloc_scratches() fails to allocate memory
ipcomp_scratches holds obsolete address. So when we try to free the
percpu scratches using ipcomp_free_scratches() it tries to vfree non
existent vm area. Described below:
static void * __percpu *ipcomp_alloc_scratches(void)
{
...
scratches = alloc_percpu(void *);
if (!scratches)
return NULL;
ipcomp_scratches does not know about this allocation failure.
Therefore holding the old obsolete address.
...
}
So when we free,
static void ipcomp_free_scratches(void)
{
...
scratches = ipcomp_scratches;
Assigning obsolete address from ipcomp_scratches
if (!scratches)
return;
for_each_possible_cpu(i)
vfree(*per_cpu_ptr(scratches, i));
Trying to free non existent page, causing warning: trying to vfree
existent vm area.
...
}
Fix this breakage by updating ipcomp_scrtches with NULL when scratches
is freed
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: syzbot+5ec9bb042ddfe9644773@syzkaller.appspotmail.com
Tested-by: syzbot+5ec9bb042ddfe9644773@syzkaller.appspotmail.com
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
