commit 1de67a3dee upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f7 upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8199be001a upstream.
When investigating a slab cache bloat problem, significant amount of
negative dentry cache was seen, but confusingly they neither got shrunk
by reclaimer (the host has very tight memory) nor be shrunk by dropping
cache. The vmcore shows there are over 14M negative dentry objects on
lru, but tracing result shows they were even not scanned at all.
Further investigation shows the memcg's vfs shrinker_map bit is not set.
So the reclaimer or dropping cache just skip calling vfs shrinker. So
we have to reboot the hosts to get the memory back.
I didn't manage to come up with a reproducer in test environment, and
the problem can't be reproduced after rebooting. But it seems there is
race between shrinker map bit clear and reparenting by code inspection.
The hypothesis is elaborated as below.
The memcg hierarchy on our production environment looks like:
root
/ \
system user
The main workloads are running under user slice's children, and it
creates and removes memcg frequently. So reparenting happens very often
under user slice, but no task is under user slice directly.
So with the frequent reparenting and tight memory pressure, the below
hypothetical race condition may happen:
CPU A CPU B
reparent
dst->nr_items == 0
shrinker:
total_objects == 0
add src->nr_items to dst
set_bit
return SHRINK_EMPTY
clear_bit
child memcg offline
replace child's kmemcg_id with
parent's (in memcg_offline_kmem())
list_lru_del() between shrinker runs
see parent's kmemcg_id
dec dst->nr_items
reparent again
dst->nr_items may go negative
due to concurrent list_lru_del()
The second run of shrinker:
read nr_items without any
synchronization, so it may
see intermediate negative
nr_items then total_objects
may return 0 coincidently
keep the bit cleared
dst->nr_items != 0
skip set_bit
add scr->nr_item to dst
After this point dst->nr_item may never go zero, so reparenting will not
set shrinker_map bit anymore. And since there is no task under user
slice directly, so no new object will be added to its lru to set the
shrinker map bit either. That bit is kept cleared forever.
How does list_lru_del() race with reparenting? It is because reparenting
replaces children's kmemcg_id to parent's without protecting from
nlru->lock, so list_lru_del() may see parent's kmemcg_id but actually
deleting items from child's lru, but dec'ing parent's nr_items, so the
parent's nr_items may go negative as commit 2788cf0c40 ("memcg:
reparent list_lrus and free kmemcg_id on css offline") says.
Since it is impossible that dst->nr_items goes negative and
src->nr_items goes zero at the same time, so it seems we could set the
shrinker map bit iff src->nr_items != 0. We could synchronize
list_lru_count_one() and reparenting with nlru->lock, but it seems
checking src->nr_items in reparenting is the simplest and avoids lock
contention.
Fixes: fae91d6d8b ("mm/list_lru.c: set bit in memcg shrinker bitmap on first list_lru item appearance")
Suggested-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Yang Shi <shy828301@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org> [4.19]
Link: https://lkml.kernel.org/r/20201202171749.264354-1-shy828301@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde3808bc8 upstream.
Fixes sparse warnings:
drivers/md/dm.c:508:12: warning: context imbalance in 'dm_prepare_ioctl' - wrong count at exit
drivers/md/dm.c:543:13: warning: context imbalance in 'dm_unprepare_ioctl' - wrong count at exit
Fixes: 971888c469 ("dm: hold DM table for duration of ioctl rather than use blkdev_get")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67aa3ec3db upstream.
Advance the maximum number of arguments to 16.
This fixes issue where certain operations, combined with table
configured args, exceed 10 arguments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 48debafe4f ("dm: add writecache target")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e6fe59ed upstream.
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c75b0ff4e upstream.
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: a124692b69 ("ftrace: Enable trampoline when rec count returns back to one")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242d990c15 upstream.
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bcd9c5be upstream.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ffccbf05 upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bb ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c98fff7332 upstream.
This is a partial revert of commit 2bb70f0a4b ("USB: serial:
option: support dynamic Quectel USB compositions")
The Quectel BG96 is different from most other modern Quectel modems,
having serial functions with 3 endpoints using ff/ff/ff and ff/fe/ff
class/subclass/protocol. Including it in the change to accommodate
dynamic function mapping was incorrect.
Revert to interface number matching for the BG96, assuming static
layout of the RMNET function on interface 4. This restores support
for the serial functions on interfaces 2 and 3.
Full lsusb output for the BG96:
Bus 002 Device 003: ID 2c7c:0296
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2c7c
idProduct 0x0296
bcdDevice 0.00
iManufacturer 3 Qualcomm, Incorporated
iProduct 2 Qualcomm CDMA Technologies MSM
iSerial 4 d1098243
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 145
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 1 Qualcomm Configuration
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 254
bInterfaceProtocol 255
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Cc: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Fixes: 2bb70f0a4b ("USB: serial: option: support dynamic Quectel USB compositions")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 156abe2961 upstream
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[sudip: use byt_gpio and vg->pdev->dev for dev_info()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2b74419e5 upstream
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ed381439e upstream.
i40iw_mmap manipulates the vma->vm_pgoff to differentiate a push page mmap
vs a doorbell mmap, and uses it to compute the pfn in remap_pfn_range
without any validation. This is vulnerable to an mmap exploit as described
in: https://lore.kernel.org/r/20201119093523.7588-1-zhudi21@huawei.com
The push feature is disabled in the driver currently and therefore no push
mmaps are issued from user-space. The feature does not work as expected in
the x722 product.
Remove the push module parameter and all VMA attribute manipulations for
this feature in i40iw_mmap. Update i40iw_mmap to only allow DB user
mmapings at offset = 0. Check vm_pgoff for zero and if the mmaps are bound
to a single page.
Cc: <stable@kernel.org>
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Link: https://lore.kernel.org/r/20201125005616.1800-2-shiraz.saleem@intel.com
Reported-by: Di Zhu <zhudi21@huawei.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310e3a4b5a upstream.
This patch reverts commit 978defee11 ("tracing: Do a WARN_ON()
if start_thread() in hwlat is called when thread exists")
.start hook can be legally called several times if according
tracer is stopped
screen window 1
[root@localhost ~]# echo 1 > /sys/kernel/tracing/events/kmem/kfree/enable
[root@localhost ~]# echo 1 > /sys/kernel/tracing/options/pause-on-trace
[root@localhost ~]# less -F /sys/kernel/tracing/trace
screen window 2
[root@localhost ~]# cat /sys/kernel/debug/tracing/tracing_on
0
[root@localhost ~]# echo hwlat > /sys/kernel/debug/tracing/current_tracer
[root@localhost ~]# echo 1 > /sys/kernel/debug/tracing/tracing_on
[root@localhost ~]# cat /sys/kernel/debug/tracing/tracing_on
0
[root@localhost ~]# echo 2 > /sys/kernel/debug/tracing/tracing_on
triggers warning in dmesg:
WARNING: CPU: 3 PID: 1403 at kernel/trace/trace_hwlat.c:371 hwlat_tracer_start+0xc9/0xd0
Link: https://lkml.kernel.org/r/bd4d3e70-400d-9c82-7b73-a2d695e86b58@virtuozzo.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 978defee11 ("tracing: Do a WARN_ON() if start_thread() in hwlat is called when thread exists")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d521943f7 ]
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670fc ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b3292215 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d2bb5ad89 ]
When command interface is down, driver to reclaim all 4K page chucks that
were hold by the Firmeware. Fix a bug for 64K page size systems, where
driver repeatedly released only the first chunk of the page.
Define helper function to fill 4K chunks for a given Firmware pages.
Iterate over all unreleased Firmware pages and call the hepler per each.
Fixes: 5adff6a088 ("net/mlx5: Fix incorrect page count when in internal error")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 391119fb5c ]
The "skb" is freed by the transmit code in cxgb4_ofld_send() and we
shouldn't use it again. But in the current code, if we hit an error
later on in the function then the clean up code will call kfree_skb(skb)
and so it causes a double free.
Set the "skb" to NULL and that makes the kfree_skb() a no-op.
Fixes: d25f2f71f6 ("crypto: chtls - Program the TLS session Key")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ilb6PtBRLWiSHp@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ee50c8e26 ]
The .x25_addr[] address comes from the user and is not necessarily
NUL terminated. This leads to a couple problems. The first problem is
that the strlen() in x25_bind() can read beyond the end of the buffer.
The second problem is more subtle and could result in memory corruption.
The call tree is:
x25_connect()
--> x25_write_internal()
--> x25_addr_aton()
The .x25_addr[] buffers are copied to the "addresses" buffer from
x25_write_internal() so it will lead to stack corruption.
Verify that the strings are NUL terminated and return -EINVAL if they
are not.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: a9288525d2 ("X25: Dont let x25_bind use addresses containing characters")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/X8ZeAKm8FnFpN//B@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 832ba59649 ]
syzkaller managed to crash the kernel using an NBMA ip6gre interface. I
could reproduce it creating an NBMA ip6gre interface and forwarding
traffic to it:
skbuff: skb_under_panic: text:ffffffff8250e927 len:148 put:44 head:ffff8c03c7a33
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:109!
Call Trace:
skb_push+0x10/0x10
ip6gre_header+0x47/0x1b0
neigh_connected_output+0xae/0xf0
ip6gre tunnel provides its own header_ops->create, and sets it
conditionally when initializing the tunnel in NBMA mode. When
header_ops->create is used, dev->hard_header_len should reflect the
length of the header created. Otherwise, when not used,
dev->needed_headroom should be used.
Fixes: eb95f52fc7 ("net: ipv6_gre: Fix GRO to work on IPv6 over GRE tap")
Cc: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20201130161911.464106-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba246c1751 ]
TX completions received with an error return code are not
being processed properly. When an error code is seen, do not
proceed to the next completion before cleaning up the existing
entry's data structures.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b71ec95223 ]
Ensure that received Subordinate Command-Response Queue (SCRQ)
entries are properly read in order by the driver. These queues
are used in the ibmvnic device to process RX buffer and TX completion
descriptors. dma_rmb barriers have been added after checking for a
pending descriptor to ensure the correct descriptor entry is checked
and after reading the SCRQ descriptor to ensure the entire
descriptor is read before processing.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ebf179037 ]
When inet_rtm_getroute() was converted to use the RCU variants of
ip_route_input() and ip_route_output_key(), the TOS parameters
stopped being masked with IPTOS_RT_MASK before doing the route lookup.
As a result, "ip route get" can return a different route than what
would be used when sending real packets.
For example:
$ ip route add 192.0.2.11/32 dev eth0
$ ip route add unreachable 192.0.2.11/32 tos 2
$ ip route get 192.0.2.11 tos 2
RTNETLINK answers: No route to host
But, packets with TOS 2 (ECT(0) if interpreted as an ECN bit) would
actually be routed using the first route:
$ ping -c 1 -Q 2 192.0.2.11
PING 192.0.2.11 (192.0.2.11) 56(84) bytes of data.
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.173 ms
--- 192.0.2.11 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.173/0.173/0.173/0.000 ms
This patch re-applies IPTOS_RT_MASK in inet_rtm_getroute(), to
return results consistent with real route lookups.
Fixes: 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/b2d237d08317ca55926add9654a48409ac1b8f5b.1606412894.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44f64f23ba ]
Netfilter changes PACKET_OTHERHOST to PACKET_HOST before invoking the
hooks as, while it's an expected value for a bridge, routing expects
PACKET_HOST. The change is undone later on after hook traversal. This
can be seen with pairs of functions updating skb>pkt_type and then
reverting it to its original value:
For hook NF_INET_PRE_ROUTING:
setup_pre_routing / br_nf_pre_routing_finish
For hook NF_INET_FORWARD:
br_nf_forward_ip / br_nf_forward_finish
But the third case where netfilter does this, for hook
NF_INET_POST_ROUTING, the packet type is changed in br_nf_post_routing
but never reverted. A comment says:
/* We assume any code from br_dev_queue_push_xmit onwards doesn't care
* about the value of skb->pkt_type. */
But when having a tunnel (say vxlan) attached to a bridge we have the
following call trace:
br_nf_pre_routing
br_nf_pre_routing_ipv6
br_nf_pre_routing_finish
br_nf_forward_ip
br_nf_forward_finish
br_nf_post_routing <- pkt_type is updated to PACKET_HOST
br_nf_dev_queue_xmit <- but not reverted to its original value
vxlan_xmit
vxlan_xmit_one
skb_tunnel_check_pmtu <- a check on pkt_type is performed
In this specific case, this creates issues such as when an ICMPv6 PTB
should be sent back. When CONFIG_BRIDGE_NETFILTER is enabled, the PTB
isn't sent (as skb_tunnel_check_pmtu checks if pkt_type is PACKET_HOST
and returns early).
If the comment is right and no one cares about the value of
skb->pkt_type after br_dev_queue_push_xmit (which isn't true), resetting
it to its original value should be safe.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20201123174902.622102-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2980cbd4dc ]
Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
the VFs;
Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.
Fixes: 6a9ddb36ee ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
