[ Upstream commit 37c5f9e80e ]
Commit 46b5889cc2 ("mtd: implement proper partition handling")
started using "mtd_get_master_ofs()" in mtd callbacks to determine
memory offsets by means of 'part' field from mtd_info, what previously
was smashed accessing 'master' field in the mtd_set_dev_defaults() method.
That provides wrong offset what causes hardware access errors.
Just make 'part', 'master' as separate fields, rather than using
union type to avoid 'part' data corruption when mtd_set_dev_defaults()
is called.
Fixes: 46b5889cc2 ("mtd: implement proper partition handling")
Signed-off-by: Oleksandr Ocheretnyi <oocheret@cisco.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220417184649.449289-1-oocheret@cisco.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87950929e2 ]
If EINT_MTK is m and PINCTRL_MTK_V2 is y, build fails:
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_set_config':
pinctrl-moore.c:(.text+0xa6c): undefined reference to `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o: In function `mtk_gpio_to_irq':
pinctrl-moore.c:(.text+0xacc): undefined reference to `mtk_eint_find_irq'
Select EINT_MTK for PINCTRL_MTK_V2 to fix this.
Fixes: 8174a8512e ("pinctrl: mediatek: make MediaTek pinctrl v2 driver ready for buidling loadable module")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20220409105958.37412-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c8045d48d ]
If clk_prepare_enable() fails we call clk_disable_unprepare()
in the error path what results in a warning that the clock
is disabled and unprepared already.
And if we fail later in phy_g12a_usb3_pcie_probe() then we
bail out w/o calling clk_disable_unprepare().
This patch fixes both errors.
Fixes: 36077e16c0 ("phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo PHY Driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8e416f95-1084-ee28-860e-7884f7fa2e32@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ff3df872 ]
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff71 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942da3af32 ]
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d79975 ("ARM: dts: am3517-evm: Add support for UI board and Audio")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d644e0d798 ]
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c640d9544 ]
Commit bf781869e5 ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d83 ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.
Fixes: bf781869e5 ("ARM: dts: at91: add pinctrl-{names, 0} for all gpios")
Depends-on: 5c8b498529 ("ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name")
Reported-by: Ajay Kathat <ajay.kathat@microchip.com>
Co-developed-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Ajay Kathat <ajay.kathat@microchip.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-2-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d2453d9a3 ]
We currently are getting the following warning after a system suspend:
Powerdomain (vpe_pwrdm) didn't enter target state 0
Looks like this is because the STANDBYMODE bit for SMART_IDLE should
not be used. The TRM "Table 12-348. VPE_SYSCONFIG" says that the value
for SMART_IDLE is "0x2: Same behavior as bit-field value of 0x1". But
if the SMART_IDLE value is used, PM_VPE_PWRSTST LASTPOWERSTATEENTERED
bits always show value of 3.
Let's fix the issue by dropping SMART_IDLE for vpe. And let's also add
the missing the powerdomain for vpe.
Fixes: 1a20951605 ("ARM: dts: dra7: Add ti-sysc node for VPE")
Cc: Benoit Parrot <bparrot@ti.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a12315d6d2 ]
On beagleboard revisions A to B4 we need to use gpt12 as the system timer.
However, the quirk handling added for gpt12 caused a regression for system
suspend for am335x as the PM coprocessor needs the timers idled for
suspend.
Let's make the gpt12 quirk specific to omap34xx, other SoCs don't need
it. Beagleboard revisions C and later no longer need to use the gpt12
related quirk. Then at some point, if we decide to drop support for the old
beagleboard revisions A to B4, we can also drop the gpt12 related quirks
completely.
Fixes: 3ff340e24c ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f83e6b416 ]
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c078614 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 962dd65e57 ]
The labels for lines 61 through 84 on the periphs-banks were offset by 2.
2 lines are missing in the BOOT GPIO lines (contains 14, should be 16)
Added 2 empty entries in BOOT to realigned the rest of GPIO labels
to match the Banana Pi M5 schematics.
(Thanks to Neil Armstrong for the heads up on the position of the missing pins)
Fixes: 976e920183 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Signed-off-by: Guillaume Giraudon <ggiraudon@prism19.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220411144427.874-1-ggiraudon@prism19.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa51e1dc4b ]
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e91ac20889 ]
In some situations software handles TRB events slower than adding TRBs.
If the number of TRB events to be processed in a given interrupt is exactly
the same as the event ring size 256, then the local variable
"event_ring_deq" that holds the initial dequeue position is equal to
software_dequeue after handling all 256 interrupts.
It will cause driver to not update ERDP to hardware,
Software dequeue pointer is out of sync with ERDP on interrupt exit.
On the next interrupt, the event ring may full but driver will not
update ERDP as software_dequeue is equal to ERDP.
[ 536.377115] xhci_hcd 0000:00:12.0: ERROR unknown event type 37
[ 566.933173] sd 8:0:0:0: [sdb] tag#27 uas_eh_abort_handler 0 uas-tag 7 inflight: CMD OUT
[ 566.933181] sd 8:0:0:0: [sdb] tag#27 CDB: Write(10) 2a 00 17 71 e6 78 00 00 08 00
[ 572.041186] xhci_hcd On some situataions,the0000:00:12.0: xHCI host not responding to stop endpoint command.
[ 572.057193] xhci_hcd 0000:00:12.0: Host halt failed, -110
[ 572.057196] xhci_hcd 0000:00:12.0: xHCI host controller not responding, assume dead
[ 572.057236] sd 8:0:0:0: [sdb] tag#26 uas_eh_abort_handler 0 uas-tag 6 inflight: CMD
[ 572.057240] sd 8:0:0:0: [sdb] tag#26 CDB: Write(10) 2a 00 38 eb cc d8 00 00 08 00
[ 572.057244] sd 8:0:0:0: [sdb] tag#25 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD
Hardware ERDP is updated mid event handling if there are more than 128
events in an interrupt (half of ring size).
Fix this by updating the software local variable at the same time as
hardware ERDP.
[commit message rewording -Mathias]
Fixes: dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer on purpose")
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2737fab4 ]
The fsl,scu.txt dt-binding documentation explicitly mentions
that the compatible string should be either "fsl,imx8qm-clock"
or "fsl,imx8qxp-clock", followed by "fsl,scu-clk". Also, i.MX8qm
SCU clocks and i.MX8qxp SCU clocks are really not the same, so
we have to set the compatible property according to SoC name.
Let's correct the i.MX8qm clock controller's compatible property
from
"fsl,imx8qxp-clk", "fsl,scu-clk"
to
"fsl,imx8qm-clk", "fsl,scu-clk" .
Fixes: f2180be18a ("arm64: dts: imx: add imx8qm common dts file")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8de8b71b78 ]
While checking AF_XDP copy mode combined with busy poll, strange
results were observed. rxdrop and txonly scenarios worked fine, but
l2fwd broke immediately.
After a deeper look, it turned out that for l2fwd, Tx side was exiting
early due to xsk_no_wakeup() returning true and in the end
xsk_generic_xmit() was never called. Note that AF_XDP Tx in copy mode
is syscall steered, so the current behavior is broken.
Txonly scenario only worked due to the fact that
sk_mark_napi_id_once_xdp() was never called - since Rx side is not in
the picture for this case and mentioned function is called in
xsk_rcv_check(), sk::sk_napi_id was never set, which in turn meant that
xsk_no_wakeup() was returning false (see the sk->sk_napi_id >=
MIN_NAPI_ID check in there).
To fix this, prefer busy poll in xsk_sendmsg() only when zero copy is
enabled on a given AF_XDP socket. By doing so, busy poll in copy mode
would not exit early on Tx side and eventually xsk_generic_xmit() will
be called.
Fixes: a0731952d9 ("xsk: Add busy-poll support for {recv,send}msg()")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220406155804.434493-1-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe4e0d3cb ]
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d719 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd86d85401 ]
Amlogic SM1 devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: 3d9e764830 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-3-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c4d636bc0 ]
Amlogic G12B devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b96d4e9270 ("arm64: dts: meson-g12b: support a311d and s922x cpu operating points")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220210100638.19130-2-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f84ccad5f5 ]
On QCOM platforms with EPSS flavour of cpufreq IP a throttled frequency is
obtained from another register REG_DOMAIN_STATE, thus the helper function
qcom_lmh_get_throttle_freq() should be modified accordingly, as for now
it returns gibberish since .reg_current_vote is unset for EPSS hardware.
To exclude a hardcoded magic number 19200 it is replaced by "xo" clock rate
in KHz.
Fixes: 275157b367 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit acb16b395c upstream.
We received a report[1] of kernel crashes when Cilium is used in XDP
mode with virtio_net after updating to newer kernels. After
investigating the reason it turned out that when using mergeable bufs
with an XDP program which adjusts xdp.data or xdp.data_meta page_to_buf()
calculates the build_skb address wrong because the offset can become less
than the headroom so it gets the address of the previous page (-X bytes
depending on how lower offset is):
page_to_skb: page addr ffff9eb2923e2000 buf ffff9eb2923e1ffc offset 252 headroom 256
This is a pr_err() I added in the beginning of page_to_skb which clearly
shows offset that is less than headroom by adding 4 bytes of metadata
via an xdp prog. The calculations done are:
receive_mergeable():
headroom = VIRTIO_XDP_HEADROOM; // VIRTIO_XDP_HEADROOM == 256 bytes
offset = xdp.data - page_address(xdp_page) -
vi->hdr_len - metasize;
page_to_skb():
p = page_address(page) + offset;
...
buf = p - headroom;
Now buf goes -4 bytes from the page's starting address as can be seen
above which is set as skb->head and skb->data by build_skb later. Depending
on what's done with the skb (when it's freed most often) we get all kinds
of corruptions and BUG_ON() triggers in mm[2]. We have to recalculate
the new headroom after the xdp program has run, similar to how offset
and len are recalculated. Headroom is directly related to
data_hard_start, data and data_meta, so we use them to get the new size.
The result is correct (similar pr_err() in page_to_skb, one case of
xdp_page and one case of virtnet buf):
a) Case with 4 bytes of metadata
[ 115.949641] page_to_skb: page addr ffff8b4dcfad2000 offset 252 headroom 252
[ 121.084105] page_to_skb: page addr ffff8b4dcf018000 offset 20732 headroom 252
b) Case of pushing data +32 bytes
[ 153.181401] page_to_skb: page addr ffff8b4dd0c4d000 offset 288 headroom 288
[ 158.480421] page_to_skb: page addr ffff8b4dd00b0000 offset 24864 headroom 288
c) Case of pushing data -33 bytes
[ 835.906830] page_to_skb: page addr ffff8b4dd3270000 offset 223 headroom 223
[ 840.839910] page_to_skb: page addr ffff8b4dcdd68000 offset 12511 headroom 223
Offset and headroom are equal because offset points to the start of
reserved bytes for the virtio_net header which are at buf start +
headroom, while data points at buf start + vnet hdr size + headroom so
when data or data_meta are adjusted by the xdp prog both the headroom size
and the offset change equally. We can use data_hard_start to compute the
new headroom after the xdp prog (linearized / page start case, the
virtnet buf case is similar just with bigger base offset):
xdp.data_hard_start = page_address + vnet_hdr
xdp.data = page_address + vnet_hdr + headroom
new headroom after xdp prog = xdp.data - xdp.data_hard_start - metasize
An example reproducer xdp prog[3] is below.
[1] https://github.com/cilium/cilium/issues/19453
[2] Two of the many traces:
[ 40.437400] BUG: Bad page state in process swapper/0 pfn:14940
[ 40.916726] BUG: Bad page state in process systemd-resolve pfn:053b7
[ 41.300891] kernel BUG at include/linux/mm.h:720!
[ 41.301801] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 41.302784] CPU: 1 PID: 1181 Comm: kubelet Kdump: loaded Tainted: G B W 5.18.0-rc1+ #37
[ 41.304458] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 41.306018] RIP: 0010:page_frag_free+0x79/0xe0
[ 41.306836] Code: 00 00 75 ea 48 8b 07 a9 00 00 01 00 74 e0 48 8b 47 48 48 8d 50 ff a8 01 48 0f 45 fa eb d0 48 c7 c6 18 b8 30 a6 e8 d7 f8 fc ff <0f> 0b 48 8d 78 ff eb bc 48 8b 07 a9 00 00 01 00 74 3a 66 90 0f b6
[ 41.310235] RSP: 0018:ffffac05c2a6bc78 EFLAGS: 00010292
[ 41.311201] RAX: 000000000000003e RBX: 0000000000000000 RCX: 0000000000000000
[ 41.312502] RDX: 0000000000000001 RSI: ffffffffa6423004 RDI: 00000000ffffffff
[ 41.313794] RBP: ffff993c98823600 R08: 0000000000000000 R09: 00000000ffffdfff
[ 41.315089] R10: ffffac05c2a6ba68 R11: ffffffffa698ca28 R12: ffff993c98823600
[ 41.316398] R13: ffff993c86311ebc R14: 0000000000000000 R15: 000000000000005c
[ 41.317700] FS: 00007fe13fc56740(0000) GS:ffff993cdd900000(0000) knlGS:0000000000000000
[ 41.319150] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 41.320152] CR2: 000000c00008a000 CR3: 0000000014908000 CR4: 0000000000350ee0
[ 41.321387] Call Trace:
[ 41.321819] <TASK>
[ 41.322193] skb_release_data+0x13f/0x1c0
[ 41.322902] __kfree_skb+0x20/0x30
[ 41.343870] tcp_recvmsg_locked+0x671/0x880
[ 41.363764] tcp_recvmsg+0x5e/0x1c0
[ 41.384102] inet_recvmsg+0x42/0x100
[ 41.406783] ? sock_recvmsg+0x1d/0x70
[ 41.428201] sock_read_iter+0x84/0xd0
[ 41.445592] ? 0xffffffffa3000000
[ 41.462442] new_sync_read+0x148/0x160
[ 41.479314] ? 0xffffffffa3000000
[ 41.496937] vfs_read+0x138/0x190
[ 41.517198] ksys_read+0x87/0xc0
[ 41.535336] do_syscall_64+0x3b/0x90
[ 41.551637] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 41.568050] RIP: 0033:0x48765b
[ 41.583955] Code: e8 4a 35 fe ff eb 88 cc cc cc cc cc cc cc cc e8 fb 7a fe ff 48 8b 7c 24 10 48 8b 74 24 18 48 8b 54 24 20 48 8b 44 24 08 0f 05 <48> 3d 01 f0 ff ff 76 20 48 c7 44 24 28 ff ff ff ff 48 c7 44 24 30
[ 41.632818] RSP: 002b:000000c000a2f5b8 EFLAGS: 00000212 ORIG_RAX: 0000000000000000
[ 41.664588] RAX: ffffffffffffffda RBX: 000000c000062000 RCX: 000000000048765b
[ 41.681205] RDX: 0000000000005e54 RSI: 000000c000e66000 RDI: 0000000000000016
[ 41.697164] RBP: 000000c000a2f608 R08: 0000000000000001 R09: 00000000000001b4
[ 41.713034] R10: 00000000000000b6 R11: 0000000000000212 R12: 00000000000000e9
[ 41.728755] R13: 0000000000000001 R14: 000000c000a92000 R15: ffffffffffffffff
[ 41.744254] </TASK>
[ 41.758585] Modules linked in: br_netfilter bridge veth netconsole virtio_net
and
[ 33.524802] BUG: Bad page state in process systemd-network pfn:11e60
[ 33.528617] page ffffe05dc0147b00 ffffe05dc04e7a00 ffff8ae9851ec000 (1) len 82 offset 252 metasize 4 hroom 0 hdr_len 12 data ffff8ae9851ec10c data_meta ffff8ae9851ec108 data_end ffff8ae9851ec14e
[ 33.529764] page:000000003792b5ba refcount:0 mapcount:-512 mapping:0000000000000000 index:0x0 pfn:0x11e60
[ 33.532463] flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
[ 33.532468] raw: 000fffffc0000000 0000000000000000 dead000000000122 0000000000000000
[ 33.532470] raw: 0000000000000000 0000000000000000 00000000fffffdff 0000000000000000
[ 33.532471] page dumped because: nonzero mapcount
[ 33.532472] Modules linked in: br_netfilter bridge veth netconsole virtio_net
[ 33.532479] CPU: 0 PID: 791 Comm: systemd-network Kdump: loaded Not tainted 5.18.0-rc1+ #37
[ 33.532482] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1.fc35 04/01/2014
[ 33.532484] Call Trace:
[ 33.532496] <TASK>
[ 33.532500] dump_stack_lvl+0x45/0x5a
[ 33.532506] bad_page.cold+0x63/0x94
[ 33.532510] free_pcp_prepare+0x290/0x420
[ 33.532515] free_unref_page+0x1b/0x100
[ 33.532518] skb_release_data+0x13f/0x1c0
[ 33.532524] kfree_skb_reason+0x3e/0xc0
[ 33.532527] ip6_mc_input+0x23c/0x2b0
[ 33.532531] ip6_sublist_rcv_finish+0x83/0x90
[ 33.532534] ip6_sublist_rcv+0x22b/0x2b0
[3] XDP program to reproduce(xdp_pass.c):
#include <linux/bpf.h>
#include <bpf/bpf_helpers.h>
SEC("xdp_pass")
int xdp_pkt_pass(struct xdp_md *ctx)
{
bpf_xdp_adjust_head(ctx, -(int)32);
return XDP_PASS;
}
char _license[] SEC("license") = "GPL";
compile: clang -O2 -g -Wall -target bpf -c xdp_pass.c -o xdp_pass.o
load on virtio_net: ip link set enp1s0 xdpdrv obj xdp_pass.o sec xdp_pass
CC: stable@vger.kernel.org
CC: Jason Wang <jasowang@redhat.com>
CC: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: virtualization@lists.linux-foundation.org
Fixes: 8fb7da9e99 ("virtio_net: get build_skb() buf by data ptr")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220425103703.3067292-1-razor@blackwall.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c936f9ea1 upstream.
When an iocg is in debt, its inuse weight is owned by debt handling and
should stay at 1. This invariant was broken when determining the amount of
surpluses at the beginning of donation calculation - when an iocg's
hierarchical weight is too low, the iocg is excluded from donation
calculation and its inuse is reset to its active regardless of its
indebtedness, triggering warnings like the following:
WARNING: CPU: 5 PID: 0 at block/blk-iocost.c:1416 iocg_kick_waitq+0x392/0x3a0
...
RIP: 0010:iocg_kick_waitq+0x392/0x3a0
Code: 00 00 be ff ff ff ff 48 89 4d a8 e8 98 b2 70 00 48 8b 4d a8 85 c0 0f 85 4a fe ff ff 0f 0b e9 43 fe ff ff 0f 0b e9 4d fe ff ff <0f> 0b e9 50 fe ff ff e8 a2 ae 70 00 66 90 0f 1f 44 00 00 55 48 89
RSP: 0018:ffffc90000200d08 EFLAGS: 00010016
...
<IRQ>
ioc_timer_fn+0x2e0/0x1470
call_timer_fn+0xa1/0x2c0
...
As this happens only when an iocg's hierarchical weight is negligible, its
impact likely is limited to triggering the warnings. Fix it by skipping
resetting inuse of under-weighted debtors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rik van Riel <riel@surriel.com>
Fixes: c421a3eb2e ("blk-iocost: revamp debt handling")
Cc: stable@vger.kernel.org # v5.10+
Link: https://lore.kernel.org/r/YmjODd4aif9BzFuO@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e0815b3e0 upstream.
When a XEN_HVM guest uses the XEN PIRQ/Eventchannel mechanism, then
PCI/MSI[-X] masking is solely controlled by the hypervisor, but contrary to
XEN_PV guests this does not disable PCI/MSI[-X] masking in the PCI/MSI
layer.
This can lead to a situation where the PCI/MSI layer masks an MSI[-X]
interrupt and the hypervisor grants the write despite the fact that it
already requested the interrupt. As a consequence interrupt delivery on the
affected device is not happening ever.
Set pci_msi_ignore_mask to prevent that like it's done for XEN_PV guests
already.
Fixes: 809f9267bb ("xen: map MSIs into pirqs")
Reported-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reported-by: Dusty Mabe <dustymabe@redhat.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Noah Meyerhans <noahm@debian.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuaduxj5.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec1442953 upstream.
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: 043cb41a85 ("riscv: introduce interfaces to patch kernel code")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d8a29997 upstream.
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: b78049831f ("lib: add error checking to hex2bin")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5be15767e upstream.
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac875df4d8 upstream.
The Samsung pinctrl drivers depend on OF_GPIO, which is part of GPIOLIB.
ARMv7 Exynos platform selects GPIOLIB and Samsung pinctrl drivers. ARMv8
Exynos selects only the latter leading to possible wrong configuration
on ARMv8 build:
WARNING: unmet direct dependencies detected for PINCTRL_EXYNOS
Depends on [n]: PINCTRL [=y] && OF_GPIO [=n] && (ARCH_EXYNOS [=y] || ARCH_S5PV210 || COMPILE_TEST [=y])
Selected by [y]:
- ARCH_EXYNOS [=y]
Always select the GPIOLIB from the Samsung pinctrl drivers to fix the
issue. This requires removing of OF_GPIO dependency (to avoid recursive
dependency), so add dependency on OF for COMPILE_TEST cases.
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Fixes: eed6b3eb20 ("arm64: Split out platform options to separate Kconfig")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220420141407.470955-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc90043133 upstream.
Due to what looks like a copy-paste error, the ECSPI2_MISO pad is not
muxed for SPI mode and causes reads from a slave-device connected to the
SPI header to always return zero.
Configure the ECSPI2_MISO pad for SPI mode on the gw71xx, gw72xx and
gw73xx families of boards that got this wrong.
Fixes: 6f30b27c5e ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org # 5.12
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e64d5fa504 upstream.
During hibernation process, once thaw() stage completes, the MHI endpoint
devices will be in M0 state post recovery. After that, the devices will be
powered down so that the system can enter the target sleep state. During
this stage, the PCI core will put the devices in D3hot. But this transition
is allowed by the MHI spec. The devices can only enter D3hot when it is in
M3 state.
So for fixing this issue, let's add the poweroff() callback that will get
executed before putting the system in target sleep state during
hibernation. This callback will power down the device properly so that it
could be restored during restore() or thaw() stage.
Cc: stable@vger.kernel.org
Fixes: 5f0c2ee1fe ("bus: mhi: pci-generic: Fix hibernation")
Reported-by: Hemant Kumar <quic_hemantk@quicinc.com>
Suggested-by: Hemant Kumar <quic_hemantk@quicinc.com>
Link: https://lore.kernel.org/r/20220405125907.5644-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 637674fa40 upstream.
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then, complementing commit 6cbe45d8ac ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable <stable@kernel.org>
Fixes: 1bc8cde46a ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e4deb56b0 upstream.
The current timeout for draining the tx fifo in RS485 mode is calculated by
multiplying the time it takes to transmit one character (with the given
baud rate) with the maximal number of characters in the tx queue.
This timeout is too short for two reasons:
First when calculating the time to transmit one character integer division
is used which may round down the result in case of a remainder of the
division.
Fix this by rounding up the division result.
Second the hardware may need additional time (e.g for first putting the
characters from the fifo into the shift register) before the characters are
actually put onto the wire.
To be on the safe side double the current maximum number of iterations
that are used to wait for the queue draining.
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220408233503.7251-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee82c6e41 upstream.
Commit 76821e222c ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da9
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c ("serial: imx: ensure that RX irqs are off if RX is off")
Cc: stable@vger.kernel.org # 4.17
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
