[ Upstream commit f990874b1c ]
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-ID: <20231007033049.22353-1-dinghao.liu@zju.edu.cn>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d192615c30 ]
The DSU PMU allows monitoring performance events in the DSU cluster,
which is done by configuring and reading back values from the DSU PMU
system registers. However, for write-access to be allowed by ELs lower
than EL3, the EL3 firmware needs to update the setting on the ACTLR3_EL3
register, as it is disallowed by default.
That configuration is not done on the firmware used by the MT8195 SoC,
as a consequence, booting a MT8195-based machine like
mt8195-cherry-tomato-r2 with CONFIG_ARM_DSU_PMU enabled hangs the kernel
just as it writes to the CLUSTERPMOVSCLR_EL1 register, since the
instruction faults to EL3, and BL31 apparently just re-runs the
instruction over and over.
Mark the DSU PMU node in the Devicetree with status "fail", as the
machine doesn't have a suitable firmware to make use of it from the
kernel, and allowing its driver to probe would hang the kernel.
Fixes: 37f2582883 ("arm64: dts: Add mediatek SoC mt8195 and evaluation board")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230720200753.322133-1-nfraprado@collabora.com
Link: https://lore.kernel.org/r/20231003-mediatek-fixes-v6-7-v1-5-dad7cd62a8ff@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 526c8ee04b ]
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd5485663 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
+---------+
+----| |
| | WAN PHY |
| +--| |
| | +---------+
| |
| | +----------------------------------+
| | | QCA8337 |
MDC | | | +-------+ |
------o-+--|--------o------------o--| | |
MDIO | | | | | PHY 1 |-|--to RJ45
--------o--|---o----+---------o--+--| | |
| | | | | +-------+ |
| +-------------+ | o--| | |
| | MDIO MDC | | | | PHY 2 |-|--to RJ45
eth1 | | | o--+--| | |
-----------|-|port0 | | | +-------+ |
| | | | o--| | |
| | switch core | | | | PHY 3 |-|--to RJ45
| +-------------+ o--+--| | |
| | | +-------+ |
| | o--| ... | |
+----------------------------------+
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd5485663 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 139ad11431 ]
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ac87fe54a ]
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f200bab375 ]
The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.
Fixes: 8f73b37cf3 ("phy: add support for the Layerscape SerDes 28G")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab483e3adc ]
dsi_wait4video_done() API waits for the DSI video mode engine to
become idle so that we can transmit the DCS commands in the
beginning of BLLP. However, with the current sequence, the MDP
timing engine is turned on after the panel's pre_enable() callback
which can send out the DCS commands needed to power up the panel.
During those cases, this API will always timeout and print out the
error spam leading to long bootup times and log flooding.
Fix this by checking if the DSI video engine was actually busy before
waiting for it to become idle otherwise this is a redundant wait.
changes in v2:
- move the reg read below the video mode check
- minor fixes in commit text
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/34
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/557853/
Link: https://lore.kernel.org/r/20230915204426.19011-1-quic_abhinavk@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c1a2e69bc ]
DP PHY re-initialization done using dp_ctrl_reinitialize_mainlink() will
cause PLL unlocked initially and then PLL gets locked at the end of
initialization. PLL_UNLOCKED interrupt will fire during this time if the
interrupt mask is enabled.
However currently DP driver link training implementation incorrectly
re-initializes PHY unconditionally during link training as the PHY was
already configured in dp_ctrl_enable_mainlink_clocks().
Fix this by re-initializing the PHY only if the previous link training
failed.
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/30
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/551847/
Link: https://lore.kernel.org/r/1691533190-19335-1-git-send-email-quic_khsieh@quicinc.com
[quic_abhinavk@quicinc.com: added line break in commit text]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 197c53c8ec ]
On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.
Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.
The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error
Fixes: 269f399dc1 ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e4a826129 ]
On i.MX8MP, the sai MCLK is bound with TX/RX enable bit,
which means the TX/RE enable bit need to be enabled then
MCLK can be output on PAD.
Some codec (for example: WM8962) needs the MCLK output
earlier, otherwise there will be issue for codec
configuration.
Add new soc data "mclk_with_tere" for this platform and
enable the MCLK output in startup stage.
As "mclk_with_tere" only applied to i.MX8MP, currently
The soc data is shared with i.MX8MN, so need to add
an i.MX8MN own soc data with "mclk_with_tere" disabled.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com
Link: https://lore.kernel.org/r/1683273322-2525-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org
Stable-dep-of: 197c53c8ec ("ASoC: fsl_sai: Don't disable bitclock for i.MX8MP")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d2998b843 ]
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144733.1546413-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 197c53c8ec ("ASoC: fsl_sai: Don't disable bitclock for i.MX8MP")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e1fe5d9e7 upstream.
Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure as mentioned in below scenario.
- Load snd_sof_amd_rembrandt
- Play or Record audio
- Stop audio
- Unload snd_sof_amd_rembrandt
- Reload snd_sof_amd_rembrandt
If acp_clkmux_sel register field is set, then clock source will be
set to ACP ACLK when ACP enters D0 state.
During stream stop, if there is no active stream is running then
acp firmware will set the ACP ACLK value to zero.
When driver is reloaded and clock source is selected as ACP ACLK,
as ACP ACLK is programmed to zero, firmware loading will fail.
For RMB platform, remove the clock mux selection field so that
ACP will use internal clock source when ACP enters D0 state.
Fixes: 41cb85bc4b ("ASoC: SOF: amd: Add support for Rembrandt plaform.")
Reported-by: coolstar <coolstarorganization@gmail.com>
Closes: https://github.com/thesofproject/sof/issues/8137
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230927071412.2416250-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a63e68a29 upstream.
I own an external usb Webcam, model NexiGo N930AF, which had low mic volume and
inconsistent sound quality. Video works as expected.
(snip)
[ +0.047857] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.003406] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000007] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.003900] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
[ +0.025726] usb 5-1: 3:1: cannot get usb sound sample rate freq at ep 0x86
[ +0.071482] usb 5-1: 3:2: cannot get usb sound sample rate freq at ep 0x86
[ +0.004679] usb 5-1: 3:3: cannot get usb sound sample rate freq at ep 0x86
[ +0.051607] usb 5-1: Warning! Unlikely big volume range (=4096), cval->res is probably wrong.
[ +0.000005] usb 5-1: [7] FU [Mic Capture Volume] ch = 1, val = 0/4096/1
Set up quirk cval->res to 16 for 256 levels,
Set GET_SAMPLE_RATE quirk flag to stop trying to get the sample rate.
Confirmed that happened anyway later due to the backoff mechanism, after 3 failures
All audio stream on device interfaces share the same values,
apart from wMaxPacketSize and tSamFreq :
(snip)
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 3
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 8
bDelay 1 frames
wFormatTag 0x0001 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 44100
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 5
Transfer Type Isochronous
Synch Type Asynchronous
Usage Type Data
wMaxPacketSize 0x005c 1x 92 bytes
bInterval 4
bRefresh 0
bSynchAddress 0
AudioStreaming Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x01
Sampling Frequency
bLockDelayUnits 0 Undefined
wLockDelay 0x0000
(snip)
Based on the usb data about manufacturer, SPCA2281B3 is the most likely controller IC
Manufacturer does not provide link for datasheet nor detailed specs.
No way to confirm if the firmware supports any other way of getting the sample rate.
Testing patch provides consistent good sound recording quality and volume range.
(snip)
[ +0.045764] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.106290] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000006] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.043700] usb 5-1: set resolution quirk: cval->res = 16
[ +0.002585] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
Signed-off-by: Christos Skevis <xristos.thes@gmail.com>
Link: https://lore.kernel.org/r/20231006155330.399393-1-xristos.thes@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a83d6f3bb upstream.
When a Opencomm2 Headset is connected to a Bluetooth USB dongle,
the audio playback functions properly, but the microphone does not work.
In the dmesg logs, there are messages indicating that the init_pitch
function fails when the capture process begins.
The microphone only functions when the ep pitch control is not set.
Toggling the pitch control off bypasses the init_piatch function
and allows the microphone to work.
Signed-off-by: WhaleChang <whalechang@google.com>
Link: https://lore.kernel.org/r/20231006044852.4181022-1-whalechang@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bbafc63b upstream.
Static calls invocations aren't well supported from module __init and
__exit functions. Especially the static call from cleanup_trusted() led
to a crash on x86 kernel with CONFIG_DEBUG_VIRTUAL=y.
However, the usage of static call invocations for trusted_key_init()
and trusted_key_exit() don't add any value from either a performance or
security perspective. Hence switch to use indirect function calls instead.
Note here that although it will fix the current crash report, ultimately
the static call infrastructure should be fixed to either support its
future usage from module __init and __exit functions or not.
Reported-and-tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Link: https://lore.kernel.org/lkml/ZRhKq6e5nF%2F4ZIV1@fedora/#t
Fixes: 5d0682be31 ("KEYS: trusted: Add generic trusted keys framework")
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa3998dbeb upstream.
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a85890559 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 869b6ea160 upstream.
Eric has reported that commit dabc8b2075 ("quota: fix dqput() to
follow the guarantees dquot_srcu should provide") heavily increases
runtime of generic/270 xfstest for ext4 in nojournal mode. The reason
for this is that ext4 in nojournal mode leaves dquots dirty until the last
dqput() and thus the cleanup done in quota_release_workfn() has to write
them all. Due to the way quota_release_workfn() is written this results
in synchronize_srcu() call for each dirty dquot which makes the dquot
cleanup when turning quotas off extremely slow.
To be able to avoid synchronize_srcu() for each dirty dquot we need to
rework how we track dquots to be cleaned up. Instead of keeping the last
dquot reference while it is on releasing_dquots list, we drop it right
away and mark the dquot with new DQ_RELEASING_B bit instead. This way we
can we can remove dquot from releasing_dquots list when new reference to
it is acquired and thus there's no need to call synchronize_srcu() each
time we drop dq_list_lock.
References: https://lore.kernel.org/all/ZRytn6CxFK2oECUt@debian-BULLSEYE-live-builder-AMD64
Reported-by: Eric Whitney <enwlinux@gmail.com>
Fixes: dabc8b2075 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac501397b upstream.
hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU)
races when it races with itself.
hidpp_connect_event() primarily runs from a workqueue but it also runs
on probe() and if a "device-connected" packet is received by the hw
when the thread running hidpp_connect_event() from probe() is waiting on
the hw, then a second thread running hidpp_connect_event() will be
started from the workqueue.
This opens the following races (note the below code is simplified):
1. Retrieving + printing the protocol (harmless race):
if (!hidpp->protocol_major) {
hidpp_root_get_protocol_version()
hidpp->protocol_major = response.rap.params[0];
}
We can actually see this race hit in the dmesg in the abrt output
attached to rhbz#2227968:
[ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
[ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
Testing with extra logging added has shown that after this the 2 threads
take turn grabbing the hw access mutex (send_mutex) so they ping-pong
through all the other TOCTOU cases managing to hit all of them:
2. Updating the name to the HIDPP name (harmless race):
if (hidpp->name == hdev->name) {
...
hidpp->name = new_name;
}
3. Initializing the power_supply class for the battery (problematic!):
hidpp_initialize_battery()
{
if (hidpp->battery.ps)
return 0;
probe_battery(); /* Blocks, threads take turns executing this */
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
}
4. Creating delayed input_device (potentially problematic):
if (hidpp->delayed_input)
return;
hidpp->delayed_input = hidpp_allocate_input(hdev);
The really big problem here is 3. Hitting the race leads to the following
sequence:
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
...
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
So now we have registered 2 power supplies for the same battery,
which looks a bit weird from userspace's pov but this is not even
the really big problem.
Notice how:
1. This is all devm-maganaged
2. The hidpp->battery.desc struct is shared between the 2 power supplies
3. hidpp->battery.desc.properties points to the result from the second
devm_kmemdup()
This causes a use after free scenario on USB disconnect of the receiver:
1. The last registered power supply class device gets unregistered
2. The memory from the last devm_kmemdup() call gets freed,
hidpp->battery.desc.properties now points to freed memory
3. The first registered power supply class device gets unregistered,
this involves sending a remove uevent to userspace which invokes
power_supply_uevent() to fill the uevent data
4. power_supply_uevent() uses hidpp->battery.desc.properties which
now points to freed memory leading to backtraces like this one:
Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08
...
Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event
Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0
...
Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0
Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0
Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680
Sep 22 20:01:35 eric kernel: power_supply_unregister+0x8e/0xa0
Sep 22 20:01:35 eric kernel: release_nodes+0x3d/0xb0
Sep 22 20:01:35 eric kernel: devres_release_group+0xfc/0x130
Sep 22 20:01:35 eric kernel: hid_device_remove+0x56/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4]
Sep 22 20:01:35 eric kernel: hid_device_remove+0x44/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3]
Sep 22 20:01:35 eric kernel: usb_unbind_interface+0x90/0x270
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? kobject_put+0xa0/0x1d0
Sep 22 20:01:35 eric kernel: usb_disable_device+0xcd/0x1e0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xde/0x2c0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xc3/0x2c0
Sep 22 20:01:35 eric kernel: hub_event+0xe80/0x1c10
There have been quite a few bug reports (see Link tags) about this crash.
Fix all the TOCTOU issues, including the really bad power-supply related
system crash on USB disconnect, by making probe() use the workqueue for
running hidpp_connect_event() too, so that it can never run more then once.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231005182638.3776-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 626b13f015 upstream.
Commit ff48b37802 ("scsi: Do not attempt to rescan suspended devices")
modified scsi_rescan_device() to avoid attempting rescanning a suspended
device. However, the modification added a check to verify that a SCSI
device is in the running state without checking if the device request
queue (in the case of block device) is also running, thus allowing the
exectuion of internal requests. Without checking the device request
queue, commit ff48b37802 fix is incomplete and deadlocks on resume can
still happen. Use blk_queue_pm_only() to check if the device request
queue allows executing commands in addition to checking the SCSI device
state.
Reported-by: Petr Tesarik <petr@tesarici.cz>
Fixes: ff48b37802 ("scsi: Do not attempt to rescan suspended devices")
Cc: stable@vger.kernel.org
Tested-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 528ab3e605 ]
If a duplicate attribute is found using kset_find_obj(), a reference
to that attribute is returned which needs to be disposed accordingly
using kobject_put(). Move the setting name validation into a separate
function to allow for this change without having to duplicate the
cleanup code for this setting.
As a side note, a very similar bug was fixed in
commit 7295a996fd ("platform/x86: dell-sysman: Fix reference leak"),
so it seems that the bug was copied from that driver.
Compile-tested only.
Fixes: 1bcad8e510 ("platform/x86: think-lmi: Fix issues with duplicate attributes")
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230925142819.74525-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5efdbcece ]
The delegated action infrastructure is prone to the following
race: different CPUs can try to schedule different delegated
actions on the same subflow at the same time.
Each of them will check different bits via mptcp_subflow_delegate(),
and will try to schedule the action on the related per-cpu napi
instance.
Depending on the timing, both can observe an empty delegated list
node, causing the same entry to be added simultaneously on two different
lists.
The root cause is that the delegated actions infra does not provide
a single synchronization point. Address the issue reserving an additional
bit to mark the subflow as scheduled for delegation. Acquiring such bit
guarantee the caller to own the delegated list node, and being able to
safely schedule the subflow.
Clear such bit only when the subflow scheduling is completed, ensuring
proper barrier in place.
Additionally swap the meaning of the delegated_action bitmask, to allow
the usage of the existing helper to set multiple bit at once.
Fixes: bcd9773431 ("mptcp: use delegate action to schedule 3rd ack retrans")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231004-send-net-20231004-v1-1-28de4ac663ae@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b000069a ]
For an unknown TX CQE error type (probably from a newer hardware),
still free the SKB, update the queue tail, etc., otherwise the
accounting will be wrong.
Also, TX errors can be triggered by injecting corrupted packets, so
replace the WARN_ONCE to ratelimited error logging.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit efb78fa86e ("lib/test_meminit: allocate pages up to order
MAX_ORDER") works great in kernels 6.4 and newer thanks to commit
23baf831a3 ("mm, treewide: redefine MAX_ORDER sanely"), but for older
kernels, the loop is off by one, which causes crashes when the test
runs.
Fix this up by changing "<= MAX_ORDER" "< MAX_ORDER" to allow the test
to work properly for older kernel branches.
Fixes: 421855d0d2 ("lib/test_meminit: allocate pages up to order MAX_ORDER")
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Xiaoke Wang <xkernel.wang@foxmail.com>
Cc: <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
