[ Upstream commit 30eaf02149 ]
The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20220826142030.213805-1-quanyang.wang@windriver.com
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b064d9144 ]
When the driver calls cx88_risc_buffer() to prepare the buffer, the
function call may fail, resulting in a empty buffer and null-ptr-deref
later in buffer_queue().
The following log can reveal it:
[ 41.822762] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN PTI
[ 41.824488] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 41.828027] RIP: 0010:buffer_queue+0xc2/0x500
[ 41.836311] Call Trace:
[ 41.836945] __enqueue_in_driver+0x141/0x360
[ 41.837262] vb2_start_streaming+0x62/0x4a0
[ 41.838216] vb2_core_streamon+0x1da/0x2c0
[ 41.838516] __vb2_init_fileio+0x981/0xbc0
[ 41.839141] __vb2_perform_fileio+0xbf9/0x1120
[ 41.840072] vb2_fop_read+0x20e/0x400
[ 41.840346] v4l2_read+0x215/0x290
[ 41.840603] vfs_read+0x162/0x4c0
Fix this by checking the return value of cx88_risc_buffer()
[hverkuil: fix coding style issues]
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9eab5f0bb ]
[BUG]
The following script shows that, although scrub can detect super block
errors, it never tries to fix it:
mkfs.btrfs -f -d raid1 -m raid1 $dev1 $dev2
xfs_io -c "pwrite 67108864 4k" $dev2
mount $dev1 $mnt
btrfs scrub start -B $dev2
btrfs scrub start -Br $dev2
umount $mnt
The first scrub reports the super error correctly:
scrub done for f3289218-abd3-41ac-a630-202f766c0859
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
But the second read-only scrub still reports the same super error:
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
[CAUSE]
The comments already shows that super block can be easily fixed by
committing a transaction:
/*
* If we find an error in a super block, we just report it.
* They will get written with the next transaction commit
* anyway
*/
But the truth is, such assumption is not always true, and since scrub
should try to repair every error it found (except for read-only scrub),
we should really actively commit a transaction to fix this.
[FIX]
Just commit a transaction if we found any super block errors, after
everything else is done.
We cannot do this just after scrub_supers(), as
btrfs_commit_transaction() will try to pause and wait for the running
scrub, thus we can not call it with scrub_lock hold.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415432c008 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7492a83ed9 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c9213a1d ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 088fe52374 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5848b9563 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b11d083c5d ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7c4ebe2f9 ]
Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1 - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a2565272a ]
On a MSI S270 with Fedora 37 x86_64 / systemd-251.4 the module does not
properly autoload.
This is likely caused by issues with how systemd-udevd handles the single
quote char (') which is part of the sys_vendor / chassis_vendor strings
on this laptop. As a workaround remove the single quote char + everything
behind it from the sys_vendor + chassis_vendor matches. This fixes
the module not autoloading.
Link: https://github.com/systemd/systemd/issues/24715
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220917210407.647432-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ae0632d17 ]
The definition of MIN_I64 in bw_fixed.c can cause gcc to whinge about
integer overflow, because it is treated as a positive value, which is
then negated. The temporary positive value is not necessarily
representable.
This causes the following warning:
../drivers/gpu/drm/amd/amdgpu/../display/dc/dml/calcs/bw_fixed.c:30:19:
warning: integer overflow in expression ‘-9223372036854775808’ of type
‘long long int’ results in ‘-9223372036854775808’ [-Woverflow]
30 | (int64_t)(-(1LL << 63))
| ^
Writing out (-MAX_I64 - 1) works instead.
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Tales Aparecida <tales.aparecida@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dc3471d1 ]
The strlen() function returns a size_t which is an unsigned int on 32-bit
arches and an unsigned long on 64-bit arches. But in the drm_copy_field()
function, the strlen() return value is assigned to an 'int len' variable.
Later, the len variable is passed as copy_from_user() third argument that
is an unsigned long parameter as well.
In theory, this can lead to an integer overflow via type conversion. Since
the assignment happens to a signed int lvalue instead of a size_t lvalue.
In practice though, that's unlikely since the values copied are set by DRM
drivers and not controlled by userspace. But using a size_t for len is the
correct thing to do anyways.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220705100215.572498-2-javierm@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d2cb3066f ]
syzbot is reporting cancel_delayed_work() without INIT_DELAYED_WORK() at
l2cap_chan_del() [1], for CONF_NOT_COMPLETE flag (which meant to prevent
l2cap_chan_del() from calling cancel_delayed_work()) is cleared by timer
which fires before l2cap_chan_del() is called by closing file descriptor
created by socket(AF_BLUETOOTH, SOCK_STREAM, BTPROTO_L2CAP).
l2cap_bredr_sig_cmd(L2CAP_CONF_REQ) and l2cap_bredr_sig_cmd(L2CAP_CONF_RSP)
are calling l2cap_ertm_init(chan), and they call l2cap_chan_ready() (which
clears CONF_NOT_COMPLETE flag) only when l2cap_ertm_init(chan) succeeded.
l2cap_sock_init() does not call l2cap_ertm_init(chan), and it instead sets
CONF_NOT_COMPLETE flag by calling l2cap_chan_set_defaults(). However, when
connect() is requested, "command 0x0409 tx timeout" happens after 2 seconds
from connect() request, and CONF_NOT_COMPLETE flag is cleared after 4
seconds from connect() request, for l2cap_conn_start() from
l2cap_info_timeout() callback scheduled by
schedule_delayed_work(&conn->info_timer, L2CAP_INFO_TIMEOUT);
in l2cap_connect() is calling l2cap_chan_ready().
Fix this problem by initializing delayed works used by L2CAP_MODE_ERTM
mode as soon as l2cap_chan_create() allocates a channel, like I did in
commit be85972393 ("Bluetooth: initialize skb_queue_head at
l2cap_chan_create()").
Link: https://syzkaller.appspot.com/bug?extid=83672956c7aa6af698b3 [1]
Reported-by: syzbot <syzbot+83672956c7aa6af698b3@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a04d2fc70 ]
Currently if ipcomp_alloc_scratches() fails to allocate memory
ipcomp_scratches holds obsolete address. So when we try to free the
percpu scratches using ipcomp_free_scratches() it tries to vfree non
existent vm area. Described below:
static void * __percpu *ipcomp_alloc_scratches(void)
{
...
scratches = alloc_percpu(void *);
if (!scratches)
return NULL;
ipcomp_scratches does not know about this allocation failure.
Therefore holding the old obsolete address.
...
}
So when we free,
static void ipcomp_free_scratches(void)
{
...
scratches = ipcomp_scratches;
Assigning obsolete address from ipcomp_scratches
if (!scratches)
return;
for_each_possible_cpu(i)
vfree(*per_cpu_ptr(scratches, i));
Trying to free non existent page, causing warning: trying to vfree
existent vm area.
...
}
Fix this breakage by updating ipcomp_scrtches with NULL when scratches
is freed
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: syzbot+5ec9bb042ddfe9644773@syzkaller.appspotmail.com
Tested-by: syzbot+5ec9bb042ddfe9644773@syzkaller.appspotmail.com
Signed-off-by: Khalid Masum <khalid.masum.92@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b383e8abed ]
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
Link: https://syzkaller.appspot.com/bug?extid=2ca247c2d60c7023de7f [1]
Reported-by: syzbot <syzbot+2ca247c2d60c7023de7f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/7acfa1be-4b5c-b2ce-de43-95b0593fb3e5@I-love.SAKURA.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aacd467c0a ]
tcp_md5sig_pool_populated can be read while another thread
changes its value.
The race has no consequence because allocations
are protected with tcp_md5sig_mutex.
This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21ab2afa2 ]
Currently queue_userspace_packet will call kfree_skb for all frames,
whether or not an error occurred. This can result in a single dropped
frame being reported as multiple drops in dropwatch. This functions
caller may also call kfree_skb in case of an error. This patch will
consume the skbs instead and allow caller's to use kfree_skb.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109957
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1100248a5c ]
Frames sent to userspace can be reported as dropped in
ovs_dp_process_packet, however, if they are dropped in the netlink code
then netlink_attachskb will report the same frame as dropped.
This patch checks for error codes which indicate that the frame has
already been freed.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109946
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea558855c ]
When bpftool is linked against libcap, the library runs a "constructor"
function to compute the number of capabilities of the running kernel
[0], at the beginning of the execution of the program. As part of this,
it performs multiple calls to prctl(). Some of these may fail, and set
errno to a non-zero value:
# strace -e prctl ./bpftool version
prctl(PR_CAPBSET_READ, CAP_MAC_OVERRIDE) = 1
prctl(PR_CAPBSET_READ, 0x30 /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, CAP_CHECKPOINT_RESTORE) = 1
prctl(PR_CAPBSET_READ, 0x2c /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, 0x2a /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, 0x29 /* CAP_??? */) = -1 EINVAL (Invalid argument)
** fprintf added at the top of main(): we have errno == 1
./bpftool v7.0.0
using libbpf v1.0
features: libbfd, libbpf_strict, skeletons
+++ exited with 0 +++
This has been addressed in libcap 2.63 [1], but until this version is
available everywhere, we can fix it on bpftool side.
Let's clean errno at the beginning of the main() function, to make sure
that these checks do not interfere with the batch mode, where we error
out if errno is set after a bpftool command.
[0] https://git.kernel.org/pub/scm/libs/libcap/libcap.git/tree/libcap/cap_alloc.c?h=libcap-2.65#n20
[1] https://git.kernel.org/pub/scm/libs/libcap/libcap.git/commit/?id=f25a1b7e69f7b33e6afb58b3e38f3450b7d2d9a0
Signed-off-by: Quentin Monnet <quentin@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220815162205.45043-1-quentin@isovalent.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68b99e94a4 ]
When CPU 0 is offline and intel_powerclamp is used to inject
idle, it generates kernel BUG:
BUG: using smp_processor_id() in preemptible [00000000] code: bash/15687
caller is debug_smp_processor_id+0x17/0x20
CPU: 4 PID: 15687 Comm: bash Not tainted 5.19.0-rc7+ #57
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
check_preemption_disabled+0xdd/0xe0
debug_smp_processor_id+0x17/0x20
powerclamp_set_cur_state+0x7f/0xf9 [intel_powerclamp]
...
...
Here CPU 0 is the control CPU by default and changed to the current CPU,
if CPU 0 offlined. This check has to be performed under cpus_read_lock(),
hence the above warning.
Use get_cpu() instead of smp_processor_id() to avoid this BUG.
Suggested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d93540014 ]
When value < time_unit, the parameter of ilog2() will be zero and
the return value is -1. u64(-1) is too large for shift exponent
and then will trigger shift-out-of-bounds:
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
Call Trace:
rapl_compute_time_window_core
rapl_write_data_raw
set_time_window
store_constraint_time_window_us
Signed-off-by: Chao Qin <chao.qin@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574160b854 ]
Toshiba Satellite Z830 needs the quirk video_disable_backlight_sysfs_if
for proper backlight control after suspend/resume cycles.
Toshiba Portege Z830 is simply the same laptop rebranded for certain
markets (I looked through the manual to other language sections to confirm
this) and thus also needs this quirk.
Thanks to Hans de Goede for suggesting this fix.
Link: https://www.spinics.net/lists/platform-driver-x86/msg34394.html
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Arvid Norlander <lkml@vorpal.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Arvid Norlander <lkml@vorpal.se>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07725adc55 ]
The following scenarios exist.
process A: process B:
->f2fs_drop_extent_tree ->f2fs_update_extent_cache_range
->f2fs_update_extent_tree_range
->write_lock
->set_inode_flag
->is_inode_flag_set
->__free_extent_tree // Shouldn't
// have been
// cleaned up
// here
->write_lock
In this case, the "FI_NO_EXTENT" flag is set between
f2fs_update_extent_tree_range and is_inode_flag_set
by other process. it leads to clearing the whole exten
tree which should not have happened. And we fix it by
move the setting it to the range of write_lock.
Fixes:5f281fab9b9a3 ("f2fs: disable extent_cache for fcollapse/finsert inodes")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2526d6bf27 ]
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "ntohl(ucode->code_length) * 2" multiplication can have an
integer overflow.
Fixes: 9e2c7d9994 ("crypto: cavium - Add Support for Octeon-tx CPT Engine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7f3257da8 ]
When receiving some signal, GNU Make automatically deletes the target if
it has already been changed by the interrupted recipe.
If the target is possibly incomplete due to interruption, it must be
deleted so that it will be remade from scratch on the next run of make.
Otherwise, the target would remain corrupted permanently because its
timestamp had already been updated.
Thanks to this behavior of Make, you can stop the build any time by
pressing Ctrl-C, and just run 'make' to resume it.
Kbuild also relies on this feature, but it is equivalently important
for any build systems that make decisions based on timestamps (if you
want to support Ctrl-C reliably).
However, this does not always work as claimed; Make immediately dies
with Ctrl-C if its stderr goes into a pipe.
[Test Makefile]
foo:
echo hello > $@
sleep 3
echo world >> $@
[Test Result]
$ make # hit Ctrl-C
echo hello > foo
sleep 3
^Cmake: *** Deleting file 'foo'
make: *** [Makefile:3: foo] Interrupt
$ make 2>&1 | cat # hit Ctrl-C
echo hello > foo
sleep 3
^C$ # 'foo' is often left-over
The reason is because SIGINT is sent to the entire process group.
In this example, SIGINT kills 'cat', and 'make' writes the message to
the closed pipe, then dies with SIGPIPE before cleaning the target.
A typical bad scenario (as reported by [1], [2]) is to save build log
by using the 'tee' command:
$ make 2>&1 | tee log
This can be problematic for any build systems based on Make, so I hope
it will be fixed in GNU Make. The maintainer of GNU Make stated this is
a long-standing issue and difficult to fix [3]. It has not been fixed
yet as of writing.
So, we cannot rely on Make cleaning the target. We can do it by
ourselves, in signal traps.
As far as I understand, Make takes care of SIGHUP, SIGINT, SIGQUIT, and
SITERM for the target removal. I added the traps for them, and also for
SIGPIPE just in case cmd_* rule prints something to stdout or stderr
(but I did not observe an actual case where SIGPIPE was triggered).
[Note 1]
The trap handler might be worth explaining.
rm -f $@; trap - $(sig); kill -s $(sig) $$
This lets the shell kill itself by the signal it caught, so the parent
process can tell the child has exited on the signal. Generally, this is
a proper manner for handling signals, in case the calling program (like
Bash) may monitor WIFSIGNALED() and WTERMSIG() for WCE although this may
not be a big deal here because GNU Make handles SIGHUP, SIGINT, SIGQUIT
in WUE and SIGTERM in IUE.
IUE - Immediate Unconditional Exit
WUE - Wait and Unconditional Exit
WCE - Wait and Cooperative Exit
For details, see "Proper handling of SIGINT/SIGQUIT" [4].
[Note 2]
Reverting 392885ee82 ("kbuild: let fixdep directly write to .*.cmd
files") would directly address [1], but it only saves if_changed_dep.
As reported in [2], all commands that use redirection can potentially
leave an empty (i.e. broken) target.
[Note 3]
Another (even safer) approach might be to always write to a temporary
file, and rename it to $@ at the end of the recipe.
<command> > $(tmp-target)
mv $(tmp-target) $@
It would require a lot of Makefile changes, and result in ugly code,
so I did not take it.
[Note 4]
A little more thoughts about a pattern rule with multiple targets (or
a grouped target).
%.x %.y: %.z
<recipe>
When interrupted, GNU Make deletes both %.x and %.y, while this solution
only deletes $@. Probably, this is not a big deal. The next run of make
will execute the rule again to create $@ along with the other files.
[1]: https://lore.kernel.org/all/YLeot94yAaM4xbMY@gmail.com/
[2]: https://lore.kernel.org/all/20220510221333.2770571-1-robh@kernel.org/
[3]: https://lists.gnu.org/archive/html/help-make/2021-06/msg00001.html
[4]: https://www.cons.org/cracauer/sigint.html
Fixes: 392885ee82 ("kbuild: let fixdep directly write to .*.cmd files")
Reported-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68dbe80f5b ]
A warning is shown during shutdown,
__dma_async_device_channel_unregister called while 2 clients hold a reference
WARNING: CPU: 15 PID: 1 at drivers/dma/dmaengine.c:1110 __dma_async_device_channel_unregister+0xb7/0xc0
Call dma_release_channel for occupied channles before dma_async_device_unregister.
Fixes: 54cce8ecb9 ("crypto: ccp - ccp_dmaengine_unregister release dma channels")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Koba Ko <koba.ko@canonical.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
