[ Upstream commit c1e3397917 ]
In accordance with [1, 2] the DW eDMA controller has been created to be
part of the DW PCIe Root Port and DW PCIe End-point controllers and to
offload the transferring of large blocks of data between application and
remote PCIe domains leaving the system CPU free for other tasks. In the
first case (eDMA being part of DW PCIe Root Port) the eDMA controller is
always accessible via the CPU DBI interface and never over the PCIe wire.
The latter case is more complex. Depending on the DW PCIe End-Point IP-core
synthesize parameters it's possible to have the eDMA registers accessible
not only from the application CPU side, but also via mapping the eDMA CSRs
over a dedicated endpoint BAR. So based on the specifics denoted above the
eDMA driver is supposed to support two types of the DMA controller setups:
1) eDMA embedded into the DW PCIe Root Port/End-point and accessible over
the local CPU from the application side.
2) eDMA embedded into the DW PCIe End-point and accessible via the PCIe
wire with MWr/MRd TLPs generated by the CPU PCIe host controller.
Since the CPU memory resides different sides in these cases the semantics
of the MEM_TO_DEV and DEV_TO_MEM operations is flipped with respect to the
Tx and Rx DMA channels. So MEM_TO_DEV/DEV_TO_MEM corresponds to the Tx/Rx
channels in setup 1) and to the Rx/Tx channels in case of setup 2).
The DW eDMA driver has supported the case 2) since e63d79d1ff
("dmaengine: Add Synopsys eDMA IP core driver") in the framework of the
drivers/dma/dw-edma/dw-edma-pcie.c driver.
The case 1) support was added later by bd96f1b2f4 ("dmaengine: dw-edma:
support local dma device transfer semantics"). Afterwards the driver was
supposed to cover the both possible eDMA setups, but the latter commit
turned out to be not fully correct.
The problem was that the commit together with the new functionality support
also changed the channel direction semantics so the eDMA Read-channel
(corresponding to the DMA_DEV_TO_MEM direction for case 1) now uses the
sgl/cyclic base addresses as the Source addresses of the DMA transfers and
dma_slave_config.dst_addr as the Destination address of the DMA transfers.
Similarly the eDMA Write-channel (corresponding to the DMA_MEM_TO_DEV
direction for case 1) now uses dma_slave_config.src_addr as a source
address of the DMA transfers and sgl/cyclic base address as the Destination
address of the DMA transfers. This contradicts the logic of the
DMA-interface, which implies that DEV side is supposed to belong to the
PCIe device memory and MEM - to the CPU/Application memory. Indeed it seems
irrational to have the SG-list defined in the PCIe bus space, while
expecting a contiguous buffer allocated in the CPU memory. Moreover the
passed SG-list and cyclic DMA buffers are supposed to be mapped in a way so
to be seen by the DW eDMA Application (CPU) interface.
So in order to have the correct DW eDMA interface we need to invert the
eDMA Rd/Wr-channels and DMA-slave directions semantics by selecting the
src/dst addresses based on the DMA transfer direction instead of using the
channel direction capability.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v.5.40a, March 2019, p.1092
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint,
v.5.40a, March 2019, p.1189
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fixes: bd96f1b2f4 ("dmaengine: dw-edma: support local dma device transfer semantics")
Link: https://lore.kernel.org/r/20220524152159.2370739-7-Frank.Li@nxp.com
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a52ed4866d ]
There are sleep in atomic context bugs when uploading device dump
data in mwifiex. The root cause is that dev_coredumpv could not
be used in atomic contexts, because it calls dev_set_name which
include operations that may sleep. The call tree shows execution
paths that could lead to bugs:
(Interrupt context)
fw_dump_timer_fn
mwifiex_upload_device_dump
dev_coredumpv(..., GFP_KERNEL)
dev_coredumpm()
kzalloc(sizeof(*devcd), gfp); //may sleep
dev_set_name
kobject_set_name_vargs
kvasprintf_const(GFP_KERNEL, ...); //may sleep
kstrdup(s, GFP_KERNEL); //may sleep
The corresponding fail log is shown below:
[ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
...
[ 135.293613] Call Trace:
[ 135.293613] <IRQ>
[ 135.293613] dump_stack_lvl+0x57/0x7d
[ 135.293613] __might_resched.cold+0x138/0x173
[ 135.293613] ? dev_coredumpm+0xca/0x2e0
[ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] dev_coredumpm+0xca/0x2e0
[ 135.293613] ? devcd_freev+0x10/0x10
[ 135.293613] dev_coredumpv+0x1c/0x20
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] mwifiex_upload_device_dump+0x65/0xb0
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] call_timer_fn+0x122/0x3d0
[ 135.293613] ? msleep_interruptible+0xb0/0xb0
[ 135.293613] ? lock_downgrade+0x3c0/0x3c0
[ 135.293613] ? __next_timer_interrupt+0x13c/0x160
[ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] __run_timers.part.0+0x3f8/0x540
[ 135.293613] ? call_timer_fn+0x3d0/0x3d0
[ 135.293613] ? arch_restore_msi_irqs+0x10/0x10
[ 135.293613] ? lapic_next_event+0x31/0x40
[ 135.293613] run_timer_softirq+0x4f/0xb0
[ 135.293613] __do_softirq+0x1c2/0x651
...
[ 135.293613] RIP: 0010:default_idle+0xb/0x10
[ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246
[ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1
[ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20
[ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b
[ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410
[ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2
...
[ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
This patch uses delayed work to replace timer and moves the operations
that may sleep into a delayed work in order to mitigate bugs, it was
tested on Marvell 88W8801 chip whose port is usb and the firmware is
usb8801_uapsta.bin. The following is the result after using delayed
work to replace timer.
[ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
As we can see, there is no bug now.
Fixes: f5ecd02a8b ("mwifiex: device dump support for usb interface")
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/b63b77fc84ed3e8a6bef02378e17c7c71a0bc3be.1654569290.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84d94e16ef ]
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1040b0d42 ]
Don't set Accessed/Dirty bits for a struct page with PG_reserved set,
i.e. don't set A/D bits for the ZERO_PAGE. The ZERO_PAGE (or pages
depending on the architecture) should obviously never be written, and
similarly there's no point in marking it accessed as the page will never
be swapped out or reclaimed. The comment in page-flags.h is quite clear
that PG_reserved pages should be managed only by their owner, and
strictly following that mandate also simplifies KVM's logic.
Fixes: 7df003c852 ("KVM: fix overflow of zero page refcount with ksm running")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220429010416.2788472-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74bb746407 ]
The last resume result exposing logic in cros_ec_sleep_event()
incorrectly requires S0ix support, which doesn't work on ARM based
systems where S0ix doesn't exist. That's because cros_ec_sleep_event()
only reports the last resume result when the EC indicates the last sleep
event was an S0ix resume. On ARM systems, the last sleep event is always
S3 resume, but the EC can still detect sleep hang events in case some
other part of the AP is blocking sleep.
Always expose the last resume result if the EC supports it so that this
works on all devices regardless of S0ix support. This fixes sleep hang
detection on ARM based chromebooks like Trogdor.
Cc: Rajat Jain <rajatja@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Fixes: 7235560ac7 ("platform/chrome: Add support for v1 of host sleep event")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220614075726.2729987-1-swboyd@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20646f5b1e ]
Commit e2be04c7f9 ("License cleanup: add SPDX license identifier to
uapi header files with a license") added the correct SPDX identifier to
include/uapi/linux/netfilter/xt_IDLETIMER.h.
A subsequent commit removed it for no reason and reintroduced the UAPI
license incorrectness as the file is now missing the UAPI exception
again.
Add it back and remove the GPLv2 boilerplate while at it.
Fixes: 68983a354a ("netfilter: xtables: Add snapshot of hardidletimer target")
Cc: Manoj Basapathi <manojbm@codeaurora.org>
Cc: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: netfilter-devel@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a61528d997 ]
There is a deadlock between sm_release and sm_cache_flush_work
which is a work item. The cancel_work_sync in sm_release will
not return until sm_cache_flush_work is finished. If we hold
mutex_lock and use cancel_work_sync to wait the work item to
finish, the work item also requires mutex_lock. As a result,
the sm_release will be blocked forever. The race condition is
shown below:
(Thread 1) | (Thread 2)
sm_release |
mutex_lock(&ftl->mutex) | sm_cache_flush_work
| mutex_lock(&ftl->mutex)
cancel_work_sync | ...
This patch moves del_timer_sync and cancel_work_sync out of
mutex_lock in order to mitigate deadlock.
Fixes: 7d17c02a01 ("mtd: Add new SmartMedia/xD FTL")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220524044841.10517-1-duoming@zju.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 381583845d ]
Smatch warnings:
drivers/hid/hid-cp2112.c:793 cp2112_xfer() error: __memcpy()
'data->block[1]' too small (33 vs 255)
drivers/hid/hid-cp2112.c:793 cp2112_xfer() error: __memcpy() 'buf' too
small (64 vs 255)
The 'read_length' variable is provided by 'data->block[0]' which comes
from user and it(read_length) can take a value between 0-255. Add an
upper bound to 'read_length' variable to prevent a buffer overflow in
memcpy().
Fixes: 542134c037 ("HID: cp2112: Fix I2C_BLOCK_DATA transactions")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c31b14d86d ]
In case push_rcu() and related functions are buggy, there's a
WARN_ON(len >= 128), which the selftest tries to hit by being tricky. In
case it is hit, we shouldn't corrupt the kernel's stack, though;
otherwise it may be hard to even receive the report that it's buggy. So
conditionalize the stack write based on that WARN_ON()'s return value.
Note that this never *actually* happens anyway. The WARN_ON() in the
first place is bounded by IS_ENABLED(DEBUG), and isn't expected to ever
actually hit. This is just a debugging sanity check.
Additionally, hoist the constant 128 into a named enum,
MAX_ALLOWEDIPS_BITS, so that it's clear why this value is chosen.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/all/CAHk-=wjJZGA6w_DxA+k7Ejbqsq+uGK==koPai3sqdsfJqemvag@mail.gmail.com/
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151c8e499f ]
Using msleep() is problematic because it's compared against
ratelimiter.c's ktime_get_coarse_boottime_ns(), which means on systems
with slow jiffies (such as UML's forced HZ=100), the result is
inaccurate. So switch to using schedule_hrtimeout().
However, hrtimer gives us access only to the traditional posix timers,
and none of the _COARSE variants. So now, rather than being too
imprecise like jiffies, it's too precise.
One solution would be to give it a large "range" value, but this will
still fire early on a loaded system. A better solution is to align the
timeout to the actual coarse timer, and then round up to the nearest
tick, plus change.
So add the timeout to the current coarse time, and then
schedule_hrtimer() until the absolute computed time.
This should hopefully reduce flakes in CI as well. Note that we keep the
retry loop in case the entire function is running behind, because the
test could still be scheduled out, by either the kernel or by the
hypervisor's kernel, in which case restarting the test and hoping to not
be scheduled out still helps.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a41b17ff9d ]
In the case of sk->dccps_qpolicy == DCCPQ_POLICY_PRIO, dccp_qpolicy_full
will drop a skb when qpolicy is full. And the lock in dccp_sendmsg is
released before sock_alloc_send_skb and then relocked after
sock_alloc_send_skb. The following conditions may lead dccp_qpolicy_push
to add skb to an already full sk_write_queue:
thread1--->lock
thread1--->dccp_qpolicy_full: queue is full. drop a skb
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_full: queue is not full. no need to drop.
thread2--->unlock
thread1--->lock
thread1--->dccp_qpolicy_push: add a skb. queue is full.
thread1--->unlock
thread2--->lock
thread2--->dccp_qpolicy_push: add a skb!
thread2--->unlock
Fix this by moving dccp_qpolicy_full.
Fixes: b1308dc015 ("[DCCP]: Set TX Queue Length Bounds via Sysctl")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220729110027.40569-1-hbh25y@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a86e86db5e ]
The prototype of input features of ionic_set_nic_features() is
netdev_features_t, but the vlan_flags is using the private
definition of ionic drivers. It should use the variable
ctx.cmd.lif_setattr.features, rather than features to check
the vlan flags. So fixes it.
Fixes: beead698b1 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 931027820e ]
Bernard reported that trying to unload rose module would lead
to infamous messages:
unregistered_netdevice: waiting for rose0 to become free. Usage count = xx
This patch solves the issue, by making sure each socket referring to
a netdevice holds a reference count on it, and properly releases it
in rose_release().
rose_dev_first() is also fixed to take a device reference
before leaving the rcu_read_locked section.
Following patch will add ref_tracker annotations to ease
future bug hunting.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec60d54cb9 ]
Fix max_rate option in TC, check for proper quanta boundaries.
Check for minimum value provided and if it fits expected 50Mbps
quanta.
Without this patch, iavf could send settings for max_rate limiting
that would be accepted from by PF even the max_rate option is less
than expected 50Mbps quanta. It results in no rate limiting
on traffic as rate limiting will be floored to 0.
Example:
tc qdisc add dev $vf root mqprio num_tc 3 map 0 2 1 queues \
2@0 2@2 2@4 hw 1 mode channel shaper bw_rlimit \
max_rate 50Mbps 500Mbps 500Mbps
Should limit TC0 to circa 50 Mbps
tc qdisc add dev $vf root mqprio num_tc 3 map 0 2 1 queues \
2@0 2@2 2@4 hw 1 mode channel shaper bw_rlimit \
max_rate 0Mbps 100Kbit 500Mbps
Should return error
Fixes: d5b33d0244 ("i40evf: add ndo_setup_tc callback to i40evf")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jun Zhang <xuejun.zhang@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 944fd1aeac ]
The commit 3c82a21f43 ("net: allow binding socket in a VRF when
there's an unbound socket") changed the inet socket lookup to avoid
packets in a VRF from matching an unbound socket. This is to ensure the
necessary isolation between the default and other VRFs for routing and
forwarding. VRF-unaware processes running in the default VRF cannot
access another VRF and have to be run with 'ip vrf exec <vrf>'. This is
to be expected with tcp_l3mdev_accept disabled, but could be reallowed
when this sysctl option is enabled. So instead of directly checking dif
and sdif in inet[6]_match, here call inet_sk_bound_dev_eq(). This
allows a match on unbound socket for non-zero sdif i.e. for packets in
a VRF, if tcp_l3mdev_accept is enabled.
Fixes: 3c82a21f43 ("net: allow binding socket in a VRF when there's an unbound socket")
Signed-off-by: Mike Manning <mvrmanning@gmail.com>
Link: https://lore.kernel.org/netdev/a54c149aed38fded2d3b5fdb1a6c89e36a083b74.camel@lasnet.de/
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08a75f1067 ]
While reading sysctl_tcp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 6dd9a14e92 ("net: Allow accepted sockets to be bound to l3mdev domain")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d368f0328 ]
INET6_MATCH() runs without holding a lock on the socket.
We probably need to annotate most reads.
This patch makes INET6_MATCH() an inline function
to ease our changes.
v2: inline function only defined if IS_ENABLED(CONFIG_IPV6)
Change the name to inet6_match(), this is no longer a macro.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fdb5fd7f73 ]
inet_request_bound_dev_if() reads sk->sk_bound_dev_if twice
while listener socket is not locked.
Another cpu could change this field under us.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4915d50e30 ]
INET_MATCH() runs without holding a lock on the socket.
We probably need to annotate most reads.
This patch makes INET_MATCH() an inline function
to ease our changes.
v2:
We remove the 32bit version of it, as modern compilers
should generate the same code really, no need to
try to be smarter.
Also make 'struct net *net' the first argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45f5d0176d ]
The authentication algorithm supports a maximum of 128-byte keys.
The allocated key memory is insufficient.
Fixes: 2f072d75d1 ("crypto: hisilicon - Add aead support on SEC2")
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa4d57b857 ]
Without MODULE_DEVICE_TABLE, crypto_safexcel.ko module is not automatically
loaded on platforms where inside-secure crypto HW is specified in device
tree (e.g. Armada 3720). So add missing MODULE_DEVICE_TABLE for of.
Fixes: 1b44c5a60c ("crypto: inside-secure - add SafeXcel EIP197 crypto engine driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98dfa9343f ]
The hpre encryption driver may be used to encrypt and decrypt packets
during the rx softirq, it is not allowed to use GFP_KERNEL.
Fixes: c8b4b47707 ("crypto: hisilicon - add HiSilicon HPRE accelerator")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 562696c3c6 ]
MLX5E_MAX_RQ_NUM_MTTS should be the maximum value, so that
MLX5_MTT_OCTW(MLX5E_MAX_RQ_NUM_MTTS) fits into u16. The current value of
1 << 17 results in MLX5_MTT_OCTW(1 << 17) = 1 << 16, which doesn't fit
into u16. This commit replaces it with the maximum value that still
fits u16.
Fixes: 73281b78a3 ("net/mlx5e: Derive Striding RQ size from MTU")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 115d9f95ea ]
The driver reports whether TX/RX TLS device offloads are supported, but
not which ciphers/versions, these should be handled by returning
-EOPNOTSUPP when .tls_dev_add() is called.
Remove the WARN_ON kernel trace when the driver gets a request to
offload a cipher/version that is not supported as it is expected.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 143201a643 ]
Not all DPB entries will be used most of the time. Unused entries will
thus have invalid timestamps. They will produce negative buffer index
which is not specifically handled. This works just by chance in current
code. It will even produce bogus pointer, but since it's not used, it
won't do any harm.
Let's fix that brittle design by skipping writing DPB entry altogether
if timestamp is invalid.
Fixes: 86caab29da ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d578e0af3a ]
Commit 7a4836560a changes simple_write_to_buffer() with memdup_user()
but it forgets to change the value to be returned that came from
simple_write_to_buffer() call. It results in the following warning:
warning: variable 'rc' is uninitialized when used here [-Wuninitialized]
return rc;
^~
Remove rc variable and just return the passed in length if the
memdup_user() succeeds.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 7a4836560a ("wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()")
Fixes: ff974e4083 ("wil6210: debugfs interface to send raw WMI command")
Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220724202452.61846-1-ammar.faizi@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6435319c34 ]
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdf6d97f0 ]
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab2d2a982f ]
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9950f11211 ]
After commit 3a5c7e4611, the variable errc is accessed before being
initialized, c.f. below W=2 warning:
| In function 'pch_can_error',
| inlined from 'pch_can_poll' at drivers/net/can/pch_can.c:739:4:
| drivers/net/can/pch_can.c:501:29: warning: 'errc' may be used uninitialized [-Wmaybe-uninitialized]
| 501 | cf->data[6] = errc & PCH_TEC;
| | ^
| drivers/net/can/pch_can.c: In function 'pch_can_poll':
| drivers/net/can/pch_can.c:484:13: note: 'errc' was declared here
| 484 | u32 errc, lec;
| | ^~~~
Moving errc initialization up solves this issue.
Fixes: 3a5c7e4611 ("can: pch_can: do not report txerr and rxerr during bus-off")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/20220721160032.9348-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e70a3263a7 ]
Currently, data[5..7] of struct can_frame, when used as a CAN error
frame, are defined as being "controller specific". Device specific
behaviours are problematic because it prevents someone from writing
code which is portable between devices.
As a matter of fact, data[5] is never used, data[6] is always used to
report TX error counter and data[7] is always used to report RX error
counter. can-utils also relies on this.
This patch updates the comment in the uapi header to specify that
data[5] is reserved (and thus should not be used) and that data[6..7]
are used for error counters.
Fixes: 0d66548a10 ("[CAN]: Add PF_CAN core module")
Link: https://lore.kernel.org/all/20220719143550.3681-11-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
