Patch 2898d1ea41
ANDROID: Address checkpatch.pl warnings in goldfish_pipe_v2
has typo in function call.
Change-Id: I3355c4a71f1e4026b6095a34cfe7adefa52f7fb6
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Cherry-pick from origin/upstream-f2fs-stable-linux-4.4.y:
39ed8376d6 ("f2fs: don't put dentry page in pagecache into highmem")
Previous dentry page uses highmem, which will cause panic in platforms
using highmem (such as arm), since the address space of dentry pages
from highmem directly goes into the decryption path via the function
fscrypt_fname_disk_to_usr. But sg_init_one assumes the address is not
from highmem, and then cause panic since it doesn't call kmap_high but
kunmap_high is triggered at the end. To fix this problem in a simple
way, this patch avoids to put dentry page in pagecache into highmem.
Change-Id: I0c87dafb92fce72bf70403a15d28c73992c03203
Signed-off-by: Yunlong Song <yunlong.song@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: fix coding style]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Changes in 4.4.121
tpm: st33zp24: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_infineon: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_nuvoton: fix potential buffer overruns caused by bit glitches on the bus
ALSA: usb-audio: Add a quirck for B&W PX headphones
ALSA: hda: Add a power_save blacklist
cpufreq: s3c24xx: Fix broken s3c_cpufreq_init()
media: m88ds3103: don't call a non-initalized function
nospec: Allow index argument to have const-qualified type
ARM: mvebu: Fix broken PL310_ERRATA_753970 selects
KVM: mmu: Fix overlap between public and private memslots
x86/syscall: Sanitize syscall table de-references under speculation fix
btrfs: Don't clear SGID when inheriting ACLs
ARM: dts: LogicPD Torpedo: Fix I2C1 pinmux
x86/apic/vector: Handle legacy irq data correctly
leds: do not overflow sysfs buffer in led_trigger_show
x86/spectre: Fix an error message
Revert "led: core: Fix brightness setting when setting delay_off=0"
bridge: check brport attr show in brport_show
fib_semantics: Don't match route with mismatching tclassid
hdlc_ppp: carrier detect ok, don't turn off negotiation
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
net: fix race on decreasing number of TX queues
net: ipv4: don't allow setting net.ipv4.route.min_pmtu below 68
netlink: ensure to loop over all netns in genlmsg_multicast_allns()
ppp: prevent unregistered channels from connecting to PPP units
udplite: fix partial checksum initialization
sctp: fix dst refcnt leak in sctp_v4_get_dst
sctp: fix dst refcnt leak in sctp_v6_get_dst()
s390/qeth: fix SETIP command handling
s390/qeth: fix IPA command submission race
sctp: verify size of a new chunk in _sctp_make_chunk()
net: mpls: Pull common label check into helper
mpls, nospec: Sanitize array index in mpls_label_ok()
dm io: fix duplicate bio completion due to missing ref count
bpf, x64: implement retpoline for tail call
btrfs: preserve i_mode if __btrfs_set_acl() fails
Linux 4.4.121
Change-Id: Ifc1f73c407f35cc1815e6f69bbed838c8ca60bc2
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
commit d7d8249665 upstream.
When changing a file's acl mask, btrfs_set_acl() will first set the
group bits of i_mode to the value of the mask, and only then set the
actual extended attribute representing the new acl.
If the second part fails (due to lack of space, for example) and the
file had no acl attribute to begin with, the system will from now on
assume that the mask permission bits are actual group permission bits,
potentially granting access to the wrong users.
Prevent this by restoring the original mode bits if __btrfs_set_acl
fails.
Signed-off-by: Ernesto A. Fernández <ernesto.mnd.fernandez@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit a493a87f38 ]
Implement a retpoline [0] for the BPF tail call JIT'ing that converts
the indirect jump via jmp %rax that is used to make the long jump into
another JITed BPF image. Since this is subject to speculative execution,
we need to control the transient instruction sequence here as well
when CONFIG_RETPOLINE is set, and direct it into a pause + lfence loop.
The latter aligns also with what gcc / clang emits (e.g. [1]).
JIT dump after patch:
# bpftool p d x i 1
0: (18) r2 = map[id:1]
2: (b7) r3 = 0
3: (85) call bpf_tail_call#12
4: (b7) r0 = 2
5: (95) exit
With CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000072 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000072 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000072 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: callq 0x000000000000006d |+
66: pause |
68: lfence |
6b: jmp 0x0000000000000066 |
6d: mov %rax,(%rsp) |
71: retq |
72: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
+ retpoline for indirect jump
Without CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000063 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000063 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000063 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: jmpq *%rax |-
63: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
- plain indirect jump as before
[0] https://support.google.com/faqs/answer/7625886
[1] a31e654fa1
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feb7695fe9 upstream.
If only a subset of the devices associated with multiple regions support
a given special operation (eg. DISCARD) then the dec_count() that is
used to set error for the region must increment the io->count.
Otherwise, when the dec_count() is called it can cause the dm-io
caller's bio to be completed multiple times. As was reported against
the dm-mirror target that had mirror legs with a mix of discard
capabilities.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=196077
Reported-by: Zhang Yi <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3968523f85 upstream.
mpls_label_ok() validates that the 'platform_label' array index from a
userspace netlink message payload is valid. Under speculation the
mpls_label_ok() result may not resolve in the CPU pipeline until after
the index is used to access an array element. Sanitize the index to zero
to prevent userspace-controlled arbitrary out-of-bounds speculation, a
precursor for a speculative execution side channel vulnerability.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.4:
- mpls_label_ok() doesn't take an extack parameter
- Drop change in mpls_getroute()]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07f2c7ab6f ]
When SCTP makes INIT or INIT_ACK packet the total chunk length
can exceed SCTP_MAX_CHUNK_LEN which leads to kernel panic when
transmitting these packets, e.g. the crash on sending INIT_ACK:
[ 597.804948] skbuff: skb_over_panic: text:00000000ffae06e4 len:120168
put:120156 head:000000007aa47635 data:00000000d991c2de
tail:0x1d640 end:0xfec0 dev:<NULL>
...
[ 597.976970] ------------[ cut here ]------------
[ 598.033408] kernel BUG at net/core/skbuff.c:104!
[ 600.314841] Call Trace:
[ 600.345829] <IRQ>
[ 600.371639] ? sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.436934] skb_put+0x16c/0x200
[ 600.477295] sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.540630] ? sctp_packet_config+0x890/0x890 [sctp]
[ 600.601781] ? __sctp_packet_append_chunk+0x3b4/0xd00 [sctp]
[ 600.671356] ? sctp_cmp_addr_exact+0x3f/0x90 [sctp]
[ 600.731482] sctp_outq_flush+0x663/0x30d0 [sctp]
[ 600.788565] ? sctp_make_init+0xbf0/0xbf0 [sctp]
[ 600.845555] ? sctp_check_transmitted+0x18f0/0x18f0 [sctp]
[ 600.912945] ? sctp_outq_tail+0x631/0x9d0 [sctp]
[ 600.969936] sctp_cmd_interpreter.isra.22+0x3be1/0x5cb0 [sctp]
[ 601.041593] ? sctp_sf_do_5_1B_init+0x85f/0xc30 [sctp]
[ 601.104837] ? sctp_generate_t1_cookie_event+0x20/0x20 [sctp]
[ 601.175436] ? sctp_eat_data+0x1710/0x1710 [sctp]
[ 601.233575] sctp_do_sm+0x182/0x560 [sctp]
[ 601.284328] ? sctp_has_association+0x70/0x70 [sctp]
[ 601.345586] ? sctp_rcv+0xef4/0x32f0 [sctp]
[ 601.397478] ? sctp6_rcv+0xa/0x20 [sctp]
...
Here the chunk size for INIT_ACK packet becomes too big, mostly
because of the state cookie (INIT packet has large size with
many address parameters), plus additional server parameters.
Later this chunk causes the panic in skb_put_data():
skb_packet_transmit()
sctp_packet_pack()
skb_put_data(nskb, chunk->skb->data, chunk->skb->len);
'nskb' (head skb) was previously allocated with packet->size
from u16 'chunk->chunk_hdr->length'.
As suggested by Marcelo we should check the chunk's length in
_sctp_make_chunk() before trying to allocate skb for it and
discard a chunk if its size bigger than SCTP_MAX_CHUNK_LEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leinter@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d22ffb5a71 ]
If multiple IPA commands are build & sent out concurrently,
fill_ipacmd_header() may assign a seqno value to a command that's
different from what send_control_data() later assigns to this command's
reply.
This is due to other commands passing through send_control_data(),
and incrementing card->seqno.ipa along the way.
So one IPA command has no reply that's waiting for its seqno, while some
other IPA command has multiple reply objects waiting for it.
Only one of those waiting replies wins, and the other(s) times out and
triggers a recovery via send_ipa_cmd().
Fix this by making sure that the same seqno value is assigned to
a command and its reply object.
Do so immediately before submitting the command & while holding the
irq_pending "lock", to produce nicely ascending seqnos.
As a side effect, *all* IPA commands now use a reply object that's
waiting for its actual seqno. Previously, early IPA commands that were
submitted while the card was still DOWN used the "catch-all" IDX seqno.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1c5b2216fb ]
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes: 5b54e16f1a ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 957d761cf9 ]
When going through the bind address list in sctp_v6_get_dst() and
the previously found address is better ('matchlen > bmatchlen'),
the code continues to the next iteration without releasing currently
held destination.
Fix it by releasing 'bdst' before continue to the next iteration, and
instead of introducing one more '!IS_ERR(bdst)' check for dst_release(),
move the already existed one right after ip6_dst_lookup_flow(), i.e. we
shouldn't proceed further if we get an error for the route lookup.
Fixes: dbc2b5e9a0 ("sctp: fix src address selection if using secondary addresses for ipv6")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a31a6b19f ]
Fix dst reference count leak in sctp_v4_get_dst() introduced in commit
410f03831 ("sctp: add routing output fallback"):
When walking the address_list, successive ip_route_output_key() calls
may return the same rt->dst with the reference incremented on each call.
The code would not decrement the dst refcount when the dst pointer was
identical from the previous iteration, causing the dst refcnt leak.
Testcase:
ip netns add TEST
ip netns exec TEST ip link set lo up
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dev dummy0 netns TEST
ip link set dev dummy1 netns TEST
ip link set dev dummy2 netns TEST
ip netns exec TEST ip addr add 192.168.1.1/24 dev dummy0
ip netns exec TEST ip link set dummy0 up
ip netns exec TEST ip addr add 192.168.1.2/24 dev dummy1
ip netns exec TEST ip link set dummy1 up
ip netns exec TEST ip addr add 192.168.1.3/24 dev dummy2
ip netns exec TEST ip link set dummy2 up
ip netns exec TEST sctp_test -H 192.168.1.2 -P 20002 -h 192.168.1.1 -p 20000 -s -B 192.168.1.3
ip netns del TEST
In 4.4 and 4.9 kernels this results to:
[ 354.179591] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 364.419674] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 374.663664] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 384.903717] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 395.143724] unregister_netdevice: waiting for lo to become free. Usage count = 1
[ 405.383645] unregister_netdevice: waiting for lo to become free. Usage count = 1
...
Fixes: 410f03831 ("sctp: add routing output fallback")
Fixes: 0ca50d12f ("sctp: fix src address selection if using secondary addresses")
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15f35d49c9 ]
Since UDP-Lite is always using checksum, the following path is
triggered when calculating pseudo header for it:
udp4_csum_init() or udp6_csum_init()
skb_checksum_init_zero_check()
__skb_checksum_validate_complete()
The problem can appear if skb->len is less than CHECKSUM_BREAK. In
this particular case __skb_checksum_validate_complete() also invokes
__skb_checksum_complete(skb). If UDP-Lite is using partial checksum
that covers only part of a packet, the function will return bad
checksum and the packet will be dropped.
It can be fixed if we skip skb_checksum_init_zero_check() and only
set the required pseudo header checksum for UDP-Lite with partial
checksum before udp4_csum_init()/udp6_csum_init() functions return.
Fixes: ed70fcfcee ("net: Call skb_checksum_init in IPv4")
Fixes: e4f45b7f40 ("net: Call skb_checksum_init in IPv6")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77f840e3e5 ]
PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.
However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).
Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.
Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.
This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cb9f7a9a5c ]
Nowadays, nlmsg_multicast() returns only 0 or -ESRCH but this was not the
case when commit 134e63756d was pushed.
However, there was no reason to stop the loop if a netns does not have
listeners.
Returns -ESRCH only if there was no listeners in all netns.
To avoid having the same problem in the future, I didn't take the
assumption that nlmsg_multicast() returns only 0 or -ESRCH.
Fixes: 134e63756d ("genetlink: make netns aware")
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7272c2f12 ]
According to RFC 1191 sections 3 and 4, ICMP frag-needed messages
indicating an MTU below 68 should be rejected:
A host MUST never reduce its estimate of the Path MTU below 68
octets.
and (talking about ICMP frag-needed's Next-Hop MTU field):
This field will never contain a value less than 68, since every
router "must be able to forward a datagram of 68 octets without
fragmentation".
Furthermore, by letting net.ipv4.route.min_pmtu be set to negative
values, we can end up with a very large PMTU when (-1) is cast into u32.
Let's also make ip_rt_min_pmtu a u32, since it's only ever compared to
unsigned ints.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac5b70198a ]
netif_set_real_num_tx_queues() can be called when netdev is up.
That usually happens when user requests change of number of
channels/rings with ethtool -L. The procedure for changing
the number of queues involves resetting the qdiscs and setting
dev->num_tx_queues to the new value. When the new value is
lower than the old one, extra care has to be taken to ensure
ordering of accesses to the number of queues vs qdisc reset.
Currently the queues are reset before new dev->num_tx_queues
is assigned, leaving a window of time where packets can be
enqueued onto the queues going down, leading to a likely
crash in the drivers, since most drivers don't check if TX
skbs are assigned to an active queue.
Fixes: e6484930d7 ("net: allocate tx queues in register_netdevice")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca79bec237 ]
gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:
net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.
We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.
This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.
Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6c3bad1ba ]
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.
Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8c6db1dfd ]
In fib_nh_match(), if output interface or gateway are passed in
the FIB configuration, we don't have to check next hops of
multipath routes to conclude whether we have a match or not.
However, we might still have routes with different realms
matching the same output interface and gateway configuration,
and this needs to cause the match to fail. Otherwise the first
route inserted in the FIB will match, regardless of the realms:
# ip route add 1.1.1.1 dev eth0 table 1234 realms 1/2
# ip route append 1.1.1.1 dev eth0 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev eth0 scope link realms 1/2
1.1.1.1 dev eth0 scope link realms 3/4
# ip route del 1.1.1.1 dev ens3 table 1234 realms 3/4
# ip route list table 1234
1.1.1.1 dev ens3 scope link realms 3/4
whereas route with realms 3/4 should have been deleted instead.
Explicitly check for fc_flow passed in the FIB configuration
(this comes from RTA_FLOW extracted by rtm_to_fib_config()) and
fail matching if it differs from nh_tclassid.
The handling of RTA_FLOW for multipath routes later in
fib_nh_match() is still needed, as we can have multiple RTA_FLOW
attributes that need to be matched against the tclassid of each
next hop.
v2: Check that fc_flow is set before discarding the match, so
that the user can still select the first matching rule by
not specifying any realm, as suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1b12580af1 ]
Now br_sysfs_if file flush doesn't have attr show. To read it will
cause kernel panic after users chmod u+r this file.
Xiong found this issue when running the commands:
ip link add br0 type bridge
ip link add type veth
ip link set veth0 master br0
chmod u+r /sys/devices/virtual/net/veth0/brport/flush
timeout 3 cat /sys/devices/virtual/net/veth0/brport/flush
kernel crashed with NULL a pointer dereference call trace.
This patch is to fix it by return -EINVAL when brport_attr->show
is null, just the same as the check for brport_attr->store in
brport_store().
Fixes: 9cf637473c ("bridge: add sysfs hook to flush forwarding table")
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The backport of upstream commit 45d55e7bac ("x86/apic/vector: Fix off by
one in error path") missed to fixup the legacy interrupt data which is not
longer available upstream.
Handle legacy irq data correctly by clearing the legacy storage to prevent
use after free.
Fixes: 7fd1335392 ("x86/apic/vector: Fix off by one in error path") - 4.4.y
Fixes: c557481a94 ("x86/apic/vector: Fix off by one in error path") - 4.9.y
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74402055a2 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7f8a09f80 upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__btrfs_set_acl() into btrfs_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.
Fixes: 073931017b
CC: stable@vger.kernel.org
CC: linux-btrfs@vger.kernel.org
CC: David Sterba <dsterba@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.4.118, we have commit c8961332d6 (x86/syscall: Sanitize syscall
table de-references under speculation), which is a backport of upstream
commit 2fbd7af5af. But it fixed only the C part of the upstream patch
-- the IA32 sysentry. So it ommitted completely the assembly part -- the
64bit sysentry.
Fix that in this patch by explicit array_index_mask_nospec written in
assembly. The same was used in lib/getuser.S.
However, to have "sbb" working properly, we have to switch from "cmp"
against (NR_syscalls-1) to (NR_syscalls), otherwise the last syscall
number would be "and"ed by 0. It is because the original "ja" relies on
"CF" or "ZF", but we rely only on "CF" in "sbb". That means: switch to
"jae" conditional jump too.
Final note: use rcx for mask as this is exactly what is overwritten by
the 4th syscall argument (r10) right after.
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: kernel-hardening@lists.openwall.com
Cc: gregkh@linuxfoundation.org
Cc: Andy Lutomirski <luto@kernel.org>
Cc: alan@linux.intel.com
Cc: Jinpu Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0373ca7483 upstream.
commit a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ba8f9d308 upstream.
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d4d9b5a5 upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b8cb28d7c upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d24cd186d upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was inherited from qemu1 and not used anymore.
Test: manually (built the kernel)
Change-Id: Ie66773bbde4ece8ade86f441effb6a94c16b9660
Signed-off-by: Roman Kiryanov <rkir@google.com>
Also enable the roraty device in Kconfig and
defconfigs.
Change-Id: Id05325a1d7e5a03baf6f85bb28bd6ee87fa8a20c
Signed-off-by: Roman Kiryanov <rkir@google.com>
Signed-off-by: Lingfeng Yang <lfy@google.com>
Per-UID proc files require rtmutex, so add an include statement and
make CONFIG_PROC_UID depend on CONFIG_RT_MUTEXES
Bug: 74338318
Test: Previously broken bcm63xx and stm32 builds now succeed.
Change-Id: Id9d44775cf9ea04319d21d833a4666e3dfc16b40
Signed-off-by: Connor O'Brien <connoro@google.com>
When printing the driver_override parameter when it is 4095 and 4094
bytes long, the printing code would access invalid memory because we
need count + 1 bytes for printing.
Cfr. commits 4efe874aac ("PCI: Don't read past the end of sysfs
"driver_override" buffer") and bf563b01c2 ("driver core: platform:
Don't read past the end of "driver_override" buffer").
Fixes: 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding path 'driver_override'")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
(cherry picked from: https://patchwork.kernel.org/patch/10175611/)
Signed-off-by: Todd Kjos <tkjos@google.com>
Change-Id: I7a9fffc8e3cc775fcf693edae7b42d57c0a375c5
binder_send_failed_reply() is called when a synchronous
transaction fails. It reports an error to the thread that
is waiting for the completion. Given that the transaction
is synchronous, there should never be more than 1 error
response to that thread -- this was being asserted with
a WARN().
However, when exercising the driver with syzbot tests, cases
were observed where multiple "synchronous" requests were
sent without waiting for responses, so it is possible that
multiple errors would be reported to the thread. This testing
was conducted with panic_on_warn set which forced the crash.
This is easily reproduced by sending back-to-back
"synchronous" transactions without checking for any
response (eg, set read_size to 0):
bwr.write_buffer = (uintptr_t)&bc1;
bwr.write_size = sizeof(bc1);
bwr.read_buffer = (uintptr_t)&br;
bwr.read_size = 0;
ioctl(fd, BINDER_WRITE_READ, &bwr);
sleep(1);
bwr2.write_buffer = (uintptr_t)&bc2;
bwr2.write_size = sizeof(bc2);
bwr2.read_buffer = (uintptr_t)&br;
bwr2.read_size = 0;
ioctl(fd, BINDER_WRITE_READ, &bwr2);
sleep(1);
The first transaction is sent to the servicemanager and the reply
fails because no VMA is set up by this client. After
binder_send_failed_reply() is called, the BINDER_WORK_RETURN_ERROR
is sitting on the thread's todo list since the read_size was 0 and
the client is not waiting for a response.
The 2nd transaction is sent and the BINDER_WORK_RETURN_ERROR has not
been consumed, so the thread's reply_error.cmd is still set (normally
cleared when the BINDER_WORK_RETURN_ERROR is handled). Therefore
when the servicemanager attempts to reply to the 2nd failed
transaction, the error is already set and it triggers this warning.
This is a user error since it is not waiting for the synchronous
transaction to complete. If it ever does check, it will see an
error.
Changed the WARN() to a pr_warn().
Signed-off-by: Todd Kjos <tkjos@android.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit e46a3b3ba7)
Change-Id: I3365b0775ceee37bdb1d868e3ce066c260aa88ea
Without these, the goldfish x86 and x86_64 builds fail.
Test: build kernel for goldfish x86 and x86_64
Change-Id: I1cbdbaaa03404975ee51c7420927d605074c93e4
Signed-off-by: Connor O'Brien <connoro@google.com>
Add per-uid files that report the data in binary format rather than
text, to allow faster reading & parsing by userspace.
Signed-off-by: Connor O'Brien <connoro@google.com>
Bug: 72339335
Test: compare values to those reported in /proc/uid_time_in_state
Change-Id: I463039ea7f17b842be4c70024fe772539fe2ce02
