[ Upstream commit 9642fa73d0 ]
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5 ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0e370b95a ]
We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3a2 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36815b416f ]
Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8fdde1cb8 ]
Switch qmimux_unregister_device() and qmi_wwan_disconnect() to
use unregister_netdevice_queue() and unregister_netdevice_many()
instead of unregister_netdevice(). This avoids RCU stalls which
have been observed on device disconnect in certain setups otherwise.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61356088ac ]
The QMAP code in the qmi_wwan driver is based on the CodeAurora GobiNet
driver which does not process QMAP padding in the RX path correctly.
Add support for QMAP padding to qmimux_rx_fixup() according to the
description of the rmnet driver.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe8d9571dc ]
Since commit 177366bf7c the %rbp stopped pointing to %rbp of the
previous stack frame. That broke frame pointer based stack unwinding.
This commit is a partial revert of it.
Note that the location of tail_call_cnt is fixed, since the verifier
enforces MAX_BPF_STACK stack size for programs with tail calls.
Fixes: 177366bf7c ("bpf: change x86 JITed program stack layout")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86723c8640 ]
.ndo_xdp_xmit() assumes it is called under RCU. For example virtio_net
uses RCU to detect it has setup the resources for tx. The assumption
accidentally broke when introducing bulk queue in devmap.
Fixes: 5d053f9da4 ("bpf: devmap prepare xdp frames for bulking")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4dd153d55 ]
dev_map_free() waits for flush_needed bitmap to be empty in order to
ensure all flush operations have completed before freeing its entries.
However the corresponding clear_bit() was called before using the
entries, so the entries could be used after free.
All access to the entries needs to be done before clearing the bit.
It seems commit a5e2da6e97 ("bpf: netdev is never null in
__dev_map_flush") accidentally changed the clear_bit() and memory access
order.
Note that the problem happens only in __dev_map_flush(), not in
dev_map_flush_old(). dev_map_flush_old() is called only after nulling
out the corresponding netdev_map entry, so dev_map_free() never frees
the entry thus no such race happens there.
Fixes: a5e2da6e97 ("bpf: netdev is never null in __dev_map_flush")
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8891461a2 ]
It is not a good idea to try to perform any work (e.g. send an auth
frame) during reconfigure flow.
Prevent this from happening, and at the end of the reconfigure flow
requeue all the works.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5635723401 ]
In multiple SSID cases, it takes time to prepare every AP interface
to be ready in initializing phase. If a sta already knows everything it
needs to join one of the APs and sends authentication to the AP which
is not fully prepared at this point of time, AP's channel context
could be NULL. As a result, warning message occurs.
Even worse, if the AP is under attack via tools such as MDK3 and massive
authentication requests are received in a very short time, console will
be hung due to kernel warning messages.
WARN_ON_ONCE() could be a better way for indicating warning messages
without duplicate messages to flood the console.
Johannes: We still need to address the underlying problem, but we
don't really have a good handle on it yet. Suppress the
worst side-effects for now.
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
[johannes: add note, change subject]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c0c9b5753 ]
The BB expander at 0x21 i2c bus 1 fails to probe on da850-evm because
the board doesn't set has_full_constraints to true in the regulator
API.
Call regulator_has_full_constraints() at the end of board registration
just like we do in da850-lcdk and da830-evm.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b14cc313f ]
When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.
Fixes: 148f472da5 ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4729ec8c1e ]
kvm_device->destroy() seems to be supposed to free its kvm_device
struct, but vgic_its_destroy() is not currently doing this,
resulting in a memory leak, resulting in kmemleak reports such as
the following:
unreferenced object 0xffff800aeddfe280 (size 128):
comm "qemu-system-aar", pid 13799, jiffies 4299827317 (age 1569.844s)
[...]
backtrace:
[<00000000a08b80e2>] kmem_cache_alloc+0x178/0x208
[<00000000dcad2bd3>] kvm_vm_ioctl+0x350/0xbc0
Fix it.
Cc: Andre Przywara <andre.przywara@arm.com>
Fixes: 1085fdc68c ("KVM: arm64: vgic-its: Introduce new KVM ITS device")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce9a53eb3d ]
There are several scenarios that keyboard can NOT wake up system
from suspend, e.g., if a keyboard is depressed between system
device suspend phase and device noirq suspend phase, the keyboard
ISR will be called and both keyboard depress and release interrupts
will be disabled, then keyboard will no longer be able to wake up
system. Another scenario would be, if a keyboard is kept depressed,
and then system goes into suspend, the expected behavior would be
when keyboard is released, system will be waked up, but current
implementation can NOT achieve that, because both depress and release
interrupts are disabled in ISR, and the event check is still in
progress.
To fix these issues, need to make sure keyboard's depress or release
interrupt is enabled after noirq device suspend phase, this patch
moves the suspend/resume callback to noirq suspend/resume phase, and
enable the corresponding interrupt according to current keyboard status.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0e1f2110a ]
In RV32, udelay would delay the wrong cycle. When it shifts right
"UDELAY_SHIFT" bits, it either delays 0 cycle or 1 cycle. It only works
correctly in RV64. Because the 'ucycles' always needs to be 64 bits
variable.
Signed-off-by: Nick Hu <nickhu@andestech.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: fixed minor spelling error]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9364df304 ]
Get rid of gcc9 warnings like this:
arch/s390/boot/ipl_report.c: In function 'find_bootdata_space':
arch/s390/boot/ipl_report.c:42:26: warning: taking address of packed member of 'struct ipl_rb_components' may result in an unaligned pointer value [-Waddress-of-packed-member]
42 | for_each_rb_entry(comp, comps)
| ^~~~~
This is effectively the s390 variant of commit 20c6c18904
("x86/boot: Disable the address-of-packed-member compiler warning").
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0098c05a ]
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c940b1a52 ]
The return values for these memory allocations are unchecked,
which may cause an oops if the driver does not handle them after
a failure. Fix by checking the function's return code.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be32a24372 ]
It was observed that multicast packets were no longer received after
a device reset. The fix is to resend the current multicast list to
the backing device after recovery.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f94608b0c ]
Check driver state before halting it during a reset. If the driver is
not running, do nothing. Otherwise, a request to deactivate a down link
can cause an error and the reset will fail.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9520543b1 ]
[Resent to net instead of net-next - may clash with Anders Roxell's patch
series addressing duplicate module names]
Commit 31dd83b966 ("net-next: phy: new Asix Electronics PHY driver")
introduced a new PHY driver drivers/net/phy/asix.c that causes a module
name conflict with a pre-existiting driver (drivers/net/usb/asix.c).
The PHY driver is used by the X-Surf 100 ethernet card driver, and loaded
by that driver via its PHY ID. A rename of the driver looks unproblematic.
Rename PHY driver to ax88796b.c in order to resolve name conflict.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 31dd83b966 ("net-next: phy: new Asix Electronics PHY driver")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e82f2f34c ]
During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.
Work around:
The Message RAM Access Failure interrupt routine needs to check whether
MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.
In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0
Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2
Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.
This patch fixes the issue according to provided workaround.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35b7fa4d07 ]
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch adds support for the mcp25625 to the existing mcp251x driver.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0df82dcd55 ]
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch add the mcp25625 to the device tree bindings documentation.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69ae4f6aac ]
A few places in mwifiex_uap_parse_tail_ies() perform memcpy()
unconditionally, which may lead to either buffer overflow or read over
boundary.
This patch addresses the issues by checking the read size and the
destination size at each place more properly. Along with the fixes,
the patch cleans up the code slightly by introducing a temporary
variable for the token size, and unifies the error path with the
standard goto statement.
Reported-by: huangwen <huangwen@venustech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8627176b0 ]
In the error handling code of iwl_req_fw_callback(), iwl_dealloc_ucode()
is called to free data. In iwl_drv_stop(), iwl_dealloc_ucode() is called
again, which can cause double-free problems.
To fix this bug, the call to iwl_dealloc_ucode() in
iwl_req_fw_callback() is deleted.
This bug is found by a runtime fuzzing tool named FIZZER written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13ec7f10b8 ]
mwifiex_update_bss_desc_with_ie() calls memcpy() unconditionally in
a couple places without checking the destination size. Since the
source is given from user-space, this may trigger a heap buffer
overflow.
Fix it by putting the length check before performing memcpy().
This fix addresses CVE-2019-3846.
Reported-by: huangwen <huangwen@venustech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0112fa557c ]
freeing peer keys after vif down is resulting in peer key uninstall
to fail due to interface lookup failure. so fix that.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df4d737ee4 ]
According to the AD7150 configuration register description, bit 7 assumes
value 1 when the threshold mode is fixed and 0 when it is adaptive,
however, the operation that identifies this mode was considering the
opposite values.
This patch renames the boolean variable to describe it correctly and
properly replaces it in the places where it is used.
Fixes: 531efd6aa0 ("staging:iio:adc:ad7150: chan_spec conv + i2c_smbus commands + drop unused poweroff timeout control.")
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03ecad90d3 ]
Assigning local iterator to array element and using it again for
indexing would cross the array boundary.
Fix this by directly referring array element without using the local
variable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd95e678e0 ]
Backlog work for psock (sk_psock_backlog) might sleep while waiting
for memory to free up when sending packets. However, while sleeping
the socket may be closed and removed from the map by the user space
side.
This breaks an assumption in sk_stream_wait_memory, which expects the
wait queue to be still there when it wakes up resulting in a
use-after-free shown below. To fix his mark sendmsg as MSG_DONTWAIT
to avoid the sleep altogether. We already set the flag for the
sendpage case but we missed the case were sendmsg is used.
Sockmap is currently the only user of skb_send_sock_locked() so only
the sockmap paths should be impacted.
==================================================================
BUG: KASAN: use-after-free in remove_wait_queue+0x31/0x70
Write of size 8 at addr ffff888069a0c4e8 by task kworker/0:2/110
CPU: 0 PID: 110 Comm: kworker/0:2 Not tainted 5.0.0-rc2-00335-g28f9d1a3d4fe-dirty #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
Workqueue: events sk_psock_backlog
Call Trace:
print_address_description+0x6e/0x2b0
? remove_wait_queue+0x31/0x70
kasan_report+0xfd/0x177
? remove_wait_queue+0x31/0x70
? remove_wait_queue+0x31/0x70
remove_wait_queue+0x31/0x70
sk_stream_wait_memory+0x4dd/0x5f0
? sk_stream_wait_close+0x1b0/0x1b0
? wait_woken+0xc0/0xc0
? tcp_current_mss+0xc5/0x110
tcp_sendmsg_locked+0x634/0x15d0
? tcp_set_state+0x2e0/0x2e0
? __kasan_slab_free+0x1d1/0x230
? kmem_cache_free+0x70/0x140
? sk_psock_backlog+0x40c/0x4b0
? process_one_work+0x40b/0x660
? worker_thread+0x82/0x680
? kthread+0x1b9/0x1e0
? ret_from_fork+0x1f/0x30
? check_preempt_curr+0xaf/0x130
? iov_iter_kvec+0x5f/0x70
? kernel_sendmsg_locked+0xa0/0xe0
skb_send_sock_locked+0x273/0x3c0
? skb_splice_bits+0x180/0x180
? start_thread+0xe0/0xe0
? update_min_vruntime.constprop.27+0x88/0xc0
sk_psock_backlog+0xb3/0x4b0
? strscpy+0xbf/0x1e0
process_one_work+0x40b/0x660
worker_thread+0x82/0x680
? process_one_work+0x660/0x660
kthread+0x1b9/0x1e0
? __kthread_create_on_node+0x250/0x250
ret_from_fork+0x1f/0x30
Fixes: 20bf50de30 ("skbuff: Function to send an skbuf on a socket")
Reported-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25d16d124a ]
The reported rate is not scaled down correctly. After applying this patch,
the function will behave just like the v/ht equivalents.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a195cefff4 ]
GCC 9 fails to calculate the size of local constant strings and produces a
false positive:
samples/bpf/task_fd_query_user.c: In function ‘test_debug_fs_uprobe’:
samples/bpf/task_fd_query_user.c:242:67: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size 215 [-Wformat-truncation=]
242 | snprintf(buf, sizeof(buf), "/sys/kernel/debug/tracing/events/%ss/%s/id",
| ^~
243 | event_type, event_alias);
| ~~~~~~~~~~~
samples/bpf/task_fd_query_user.c:242:2: note: ‘snprintf’ output between 45 and 300 bytes into a destination of size 256
242 | snprintf(buf, sizeof(buf), "/sys/kernel/debug/tracing/events/%ss/%s/id",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
243 | event_type, event_alias);
| ~~~~~~~~~~~~~~~~~~~~~~~~
Workaround this by lowering the buffer size to a reasonable value.
Related GCC Bugzilla: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83431
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7c2d64bac ]
If the trace for read is larger than 4096, the return
value sz will be 4096. This results in off-by-one error
on buf:
static char buf[4096];
ssize_t sz;
sz = read(trace_fd, buf, sizeof(buf));
if (sz > 0) {
buf[sz] = 0;
puts(buf);
}
Signed-off-by: Chang-Hsien Tsai <luke.tw@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b23af0783 ]
The BIUCTRL register writes require that a data barrier be inserted
after comitting the write to the register for the block to latch in the
recently written values. Reads have no such requirement and are not
changed.
Fixes: 34642650e5 ("soc: Move brcmstb to bcm/brcmstb")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 490cad5a3a ]
In case setup_hifcpubiuctrl_regs() returns an error, because of e.g:
an unsupported CPU type, just catch that error and return instead of
blindly continuing with the initialization. This fixes a NULL pointer
de-reference with the code continuing without having a proper array of
registers to use.
Fixes: 22f7a9116e ("soc: brcmstb: Correct CPU_CREDIT_REG offset for Brahma-B53 CPUs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a1a42f8401 upstream.
The talitos driver has two ways to perform AEAD depending on the
HW capability. Some HW support both. It is needed to give them
different names to distingish which one it is for instance when
a test fails.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 7405c8d7ff ("crypto: talitos - templates for AEAD using HMAC_SNOOP_NO_AFEU")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f93a4f297 upstream.
It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.
Fixes: 1d069bfa3c ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler")
Cc: stable@vger.kernel.org #5.0+
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Tested-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 637dfa0fad upstream.
scripts/package/builddeb calls "make dtbs_install" after executing
a plain make (i.e. no build targets specified). It will fail if dtbs
were not built beforehand. Match the arm64 architecture where DTBs get
built by the "all" target.
Signed-off-by: Cedric Hombourger <Cedric_Hombourger@mentor.com>
[paul.burton@mips.com: s/builddep/builddeb]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b24cae4d5 upstream.
Add a missing EHB (Execution Hazard Barrier) in mtc0 -> mfc0 sequence.
Without this execution hazard barrier it's possible for the value read
back from the KScratch register to be the value from before the mtc0.
Reproducible on P5600 & P6600.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
Signed-off-by: Dmitry Korotin <dkorotin@wavecomp.com>
[paul.burton@mips.com:
- Commit message tweaks.
- Add Fixes tags.
- Mark for stable back to v3.15 where P5600 support was introduced.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3d8bfdd030 ("MIPS: Use C0_KScratch (if present) to hold PGD pointer.")
Fixes: 829dcc0a95 ("MIPS: Add MIPS P5600 probe support")
Cc: linux-mips@vger.kernel.org
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
