commit 13c30a7558 upstream.
The bus->clk_stop_timeout member is only initialized to a non-zero value
during the codec driver probe. This can lead to corner cases where this
value remains pegged at zero when the bus suspends, which results in an
endless loop in sdw_bus_wait_for_clk_prep_deprep().
Corner cases include configurations with no codecs described in the
firmware, or delays in probing codec drivers.
Initializing the default timeout to the smallest non-zero value avoid this
problem and allows for the existing logic to be preserved: the
bus->clk_stop_timeout is set as the maximum required by all codecs
connected on the bus.
Fixes: 1f2dcf3a15 ("soundwire: intel: set dev_num_ida_min")
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221020015624.1703950-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 098e5edc5d ]
While vb2_mmap took the mmap_lock mutex, vb2_get_unmapped_area didn't.
Add this.
Also take this opportunity to move the 'q->memory != VB2_MEMORY_MMAP'
check and vb2_fileio_is_active() check into __find_plane_by_offset() so
both vb2_mmap and vb2_get_unmapped_area do the same checks.
Since q->memory is checked while mmap_lock is held, also take that lock
in reqbufs and create_bufs when it is set, and set it back to
MEMORY_UNKNOWN on error.
Fixes: f035eb4e97 ("[media] videobuf2: fix lockdep warning")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74e7e1efda ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So remove kfree_skb()
from the spin_lock_irqsave() section and use the already existing
"drop" label in xenvif_start_xmit() for dropping the SKB. At the
same time replace the dev_kfree_skb() call there with a call of
dev_kfree_skb_any(), as xenvif_start_xmit() can be called with
disabled interrupts.
This is XSA-424 / CVE-2022-42328 / CVE-2022-42329.
Fixes: be81992f90 ("xen/netback: don't queue unlimited number of packages")
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad7f402ae4 ]
In some cases, the frontend may send a packet where the protocol headers
are spread across multiple slots. This would result in netback creating
an skb where the protocol headers spill over into the non-linear area.
Some drivers and NICs don't handle this properly resulting in an
interface reset or worse.
This issue was introduced by the removal of an unconditional skb pull in
the tx path to improve performance. Fix this without reintroducing the
pull by setting up grant copy ops for as many slots as needed to reach
the XEN_NETBACK_TX_COPY_LEN size. Adjust the rest of the code to handle
multiple copy operations per skb.
This is XSA-423 / CVE-2022-3643.
Fixes: 7e5d775395 ("xen-netback: remove unconditional __pskb_pull_tail() in guest Tx path")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 153695d36e ]
`hostname` needs to be set as null-pointer after free in
`cifs_put_tcp_session` function, or when `cifsd` thread attempts
to resolve hostname and reconnect the host, the thread would deref
the invalid pointer.
Here is one of practical backtrace examples as reference:
Task 477
---------------------------
do_mount
path_mount
do_new_mount
vfs_get_tree
smb3_get_tree
smb3_get_tree_common
cifs_smb3_do_mount
cifs_mount
mount_put_conns
cifs_put_tcp_session
--> kfree(server->hostname)
cifsd
---------------------------
kthread
cifs_demultiplex_thread
cifs_reconnect
reconn_set_ipaddr_from_hostname
--> if (!server->hostname)
--> if (server->hostname[0] == '\0') // !! UAF fault here
CIFS: VFS: cifs_mount failed w/return code = -112
mount error(112): Host is down
BUG: KASAN: use-after-free in reconn_set_ipaddr_from_hostname+0x2ba/0x310
Read of size 1 at addr ffff888108f35380 by task cifsd/480
CPU: 2 PID: 480 Comm: cifsd Not tainted 6.1.0-rc2-00106-gf705792f89dd-dirty #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0x85
print_report+0x16c/0x4a3
kasan_report+0x95/0x190
reconn_set_ipaddr_from_hostname+0x2ba/0x310
__cifs_reconnect.part.0+0x241/0x800
cifs_reconnect+0x65f/0xb60
cifs_demultiplex_thread+0x1570/0x2570
kthread+0x2c5/0x380
ret_from_fork+0x22/0x30
</TASK>
Allocated by task 477:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
__kasan_kmalloc+0x7e/0x90
__kmalloc_node_track_caller+0x52/0x1b0
kstrdup+0x3b/0x70
cifs_get_tcp_session+0xbc/0x19b0
mount_get_conns+0xa9/0x10c0
cifs_mount+0xdf/0x1970
cifs_smb3_do_mount+0x295/0x1660
smb3_get_tree+0x352/0x5e0
vfs_get_tree+0x8e/0x2e0
path_mount+0xf8c/0x1990
do_mount+0xee/0x110
__x64_sys_mount+0x14b/0x1f0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 477:
kasan_save_stack+0x1e/0x40
kasan_set_track+0x21/0x30
kasan_save_free_info+0x2a/0x50
__kasan_slab_free+0x10a/0x190
__kmem_cache_free+0xca/0x3f0
cifs_put_tcp_session+0x30c/0x450
cifs_mount+0xf95/0x1970
cifs_smb3_do_mount+0x295/0x1660
smb3_get_tree+0x352/0x5e0
vfs_get_tree+0x8e/0x2e0
path_mount+0xf8c/0x1990
do_mount+0xee/0x110
__x64_sys_mount+0x14b/0x1f0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff888108f35380
which belongs to the cache kmalloc-16 of size 16
The buggy address is located 0 bytes inside of
16-byte region [ffff888108f35380, ffff888108f35390)
The buggy address belongs to the physical page:
page:00000000333f8e58 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888108f350e0 pfn:0x108f35
flags: 0x200000000000200(slab|node=0|zone=2)
raw: 0200000000000200 0000000000000000 dead000000000122 ffff8881000423c0
raw: ffff888108f350e0 000000008080007a 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888108f35280: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
ffff888108f35300: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
>ffff888108f35380: fa fb fc fc fa fb fc fc fa fb fc fc fa fb fc fc
^
ffff888108f35400: fa fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888108f35480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 7be3248f31 ("cifs: To match file servers, make sure the server hostname matches")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5895c0f2 ]
Function mc146818_get_time() contains an elaborate mechanism of reading
the RTC time while no RTC update is in progress. It turns out that
reading the RTC alarm clock also requires avoiding the RTC update.
Therefore, the mechanism in mc146818_get_time() should be reused - so
extract it into a separate function.
The logic in mc146818_avoid_UIP() is same as in mc146818_get_time()
except that after every
if (CMOS_READ(RTC_FREQ_SELECT) & RTC_UIP) {
there is now "mdelay(1)".
To avoid producing a very unreadable patch, mc146818_get_time() will be
refactored to use mc146818_avoid_UIP() in the next patch.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211210200131.153887-6-mat.jonczyk@o2.pl
Stable-dep-of: cd17420ebe ("rtc: cmos: avoid UIP when writing alarm time")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d3c106e19 upstream.
pagetable walks on address ranges mapped by VMAs can be done under the
mmap lock, the lock of an anon_vma attached to the VMA, or the lock of the
VMA's address_space. Only one of these needs to be held, and it does not
need to be held in exclusive mode.
Under those circumstances, the rules for concurrent access to page table
entries are:
- Terminal page table entries (entries that don't point to another page
table) can be arbitrarily changed under the page table lock, with the
exception that they always need to be consistent for
hardware page table walks and lockless_pages_from_mm().
This includes that they can be changed into non-terminal entries.
- Non-terminal page table entries (which point to another page table)
can not be modified; readers are allowed to READ_ONCE() an entry, verify
that it is non-terminal, and then assume that its value will stay as-is.
Retracting a page table involves modifying a non-terminal entry, so
page-table-level locks are insufficient to protect against concurrent page
table traversal; it requires taking all the higher-level locks under which
it is possible to start a page walk in the relevant range in exclusive
mode.
The collapse_huge_page() path for anonymous THP already follows this rule,
but the shmem/file THP path was getting it wrong, making it possible for
concurrent rmap-based operations to cause corruption.
Link: https://lkml.kernel.org/r/20221129154730.2274278-1-jannh@google.com
Link: https://lkml.kernel.org/r/20221128180252.1684965-1-jannh@google.com
Link: https://lkml.kernel.org/r/20221125213714.4115729-1-jannh@google.com
Fixes: 27e1f82731 ("khugepaged: enable collapse pmd for pte-mapped THP")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[manual backport: this code was refactored from two copies into a common
helper between 5.15 and 6.0]
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a487069e11 ]
Add RmNet support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa07f7289 ]
If there's a disconnection while operating in eSS, there may be a delay
in VBUS drop response from the connector. In that case, the internal
link state may drop to operate in usb2 speed while the controller thinks
the VBUS is still high. The driver must make sure to disable
GUSB2PHYCFG.SUSPHY when sending endpoint command while in usb2 speed.
The End Transfer command may be called, and only that command needs to
go through at this point. Let's keep it simple and unconditionally
disable GUSB2PHYCFG.SUSPHY whenever we issue the command.
This scenario is not seen in real hardware. In a rare case, our
prototype type-c controller/interface may have a slow response
triggerring this issue.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5651117207803c26e2f22ddf4e5ce9e865dcf7c7.1668045468.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11452a370 ]
When trying to see if we can clone a file range, there are cases where we
end up sending two write operations in case the inode from the source root
has an i_size that is not sector size aligned and the length from the
current offset to its i_size is less than the remaining length we are
trying to clone.
Issuing two write operations when we could instead issue a single write
operation is not incorrect. However it is not optimal, specially if the
extents are compressed and the flag BTRFS_SEND_FLAG_COMPRESSED was passed
to the send ioctl. In that case we can end up sending an encoded write
with an offset that is not sector size aligned, which makes the receiver
fallback to decompressing the data and writing it using regular buffered
IO (so re-compressing the data in case the fs is mounted with compression
enabled), because encoded writes fail with -EINVAL when an offset is not
sector size aligned.
The following example, which triggered a bug in the receiver code for the
fallback logic of decompressing + regular buffer IO and is fixed by the
patchset referred in a Link at the bottom of this changelog, is an example
where we have the non-optimal behaviour due to an unaligned encoded write:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
mkfs.btrfs -f $DEV > /dev/null
mount -o compress $DEV $MNT
# File foo has a size of 33K, not aligned to the sector size.
xfs_io -f -c "pwrite -S 0xab 0 33K" $MNT/foo
xfs_io -f -c "pwrite -S 0xcd 0 64K" $MNT/bar
# Now clone the first 32K of file bar into foo at offset 0.
xfs_io -c "reflink $MNT/bar 0 0 32K" $MNT/foo
# Snapshot the default subvolume and create a full send stream (v2).
btrfs subvolume snapshot -r $MNT $MNT/snap
btrfs send --compressed-data -f /tmp/test.send $MNT/snap
echo -e "\nFile bar in the original filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
mkfs.btrfs -f $DEV > /dev/null
mount $DEV $MNT
echo -e "\nReceiving stream in a new filesystem..."
btrfs receive -f /tmp/test.send $MNT
echo -e "\nFile bar in the new filesystem:"
od -A d -t x1 $MNT/snap/bar
umount $MNT
Before this patch, the send stream included one regular write and one
encoded write for file 'bar', with the later being not sector size aligned
and causing the receiver to fallback to decompression + buffered writes.
The output of the btrfs receive command in verbose mode (-vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
write bar - offset=32768 length=1024
encoded_write bar - offset=33792, len=4096, unencoded_offset=33792, unencoded_file_len=31744, unencoded_len=65536, compression=1, encryption=0
encoded_write bar - falling back to decompress and write due to errno 22 ("Invalid argument")
(...)
This patch avoids the regular write followed by an unaligned encoded write
so that we end up sending a single encoded write that is aligned. So after
this patch the stream content is (output of btrfs receive -vvv):
(...)
mkfile o258-7-0
rename o258-7-0 -> bar
utimes
clone bar - source=foo source offset=0 offset=0 length=32768
encoded_write bar - offset=32768, len=4096, unencoded_offset=32768, unencoded_file_len=32768, unencoded_len=65536, compression=1, encryption=0
(...)
So we get more optimal behaviour and avoid the silent data loss bug in
versions of btrfs-progs affected by the bug referred by the Link tag
below (btrfs-progs v5.19, v5.19.1, v6.0 and v6.0.1).
Link: https://lore.kernel.org/linux-btrfs/cover.1668529099.git.fdmanana@suse.com/
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd5e1e4282 ]
The `nettest` binary, built from `selftests/net/nettest.c`,
was expected to be found in the path during test execution of
`fcnal-test.sh` and `pmtu.sh`, leading to tests getting
skipped when the binary is not installed in the system, as can
be seen in these logs found in the wild [1]:
# TEST: vti4: PMTU exceptions [SKIP]
[ 350.600250] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 350.607421] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm6udp not supported
# TEST: vti6: PMTU exceptions (ESP-in-UDP) [SKIP]
[ 351.605102] IPv6: ADDRCONF(NETDEV_CHANGE): veth_b: link becomes ready
[ 351.612243] IPv6: ADDRCONF(NETDEV_CHANGE): veth_a: link becomes ready
# 'nettest' command not found; skipping tests
# xfrm4udp not supported
The `unicast_extensions.sh` tests also rely on `nettest`, but
it runs fine there because it looks for the binary in the
current working directory [2]:
The same mechanism that works for the Unicast extensions tests
is here copied over to the PMTU and functional tests.
[1] https://lkft.validation.linaro.org/scheduler/job/5839508#L6221
[2] https://lkft.validation.linaro.org/scheduler/job/5839508#L7958
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05530ef7cf ]
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed.
seq_copy_in_user() and seq_copy_in_kernel() did not have prototypes
matching snd_seq_dump_func_t. Adjust this and remove the casts. There
are not resulting binary output differences.
This was found as a result of Clang's new -Wcast-function-type-strict
flag, which is more sensitive than the simpler -Wcast-function-type,
which only checks for type width mismatches.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202211041527.HD8TLSE1-lkp@intel.com
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221118232346.never.380-kees@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7d7d4e7bb ]
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da74858a47 ]
The clock source and the sched_clock provided by the arm_global_timer
on Rockchip rk3066a/rk3188 are quite unstable because their rates
depend on the CPU frequency.
Recent changes to the arm_global_timer driver makes it impossible to use.
On the other side, the arm_global_timer has a higher rating than the
ROCKCHIP_TIMER, it will be selected by default by the time framework
while we want to use the stable Rockchip clock source.
Keep the arm_global_timer disabled in order to have the
DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/f275ca8d-fd0a-26e5-b978-b7f3df815e0a@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ca507bf99 ]
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 340a982825 ]
Actually in no-MMU SoCs(i.e. i.MXRT) ZERO_PAGE(vaddr) expands to
```
virt_to_page(0)
```
that in order expands to:
```
pfn_to_page(virt_to_pfn(0))
```
and then virt_to_pfn(0) to:
```
((((unsigned long)(0) - PAGE_OFFSET) >> PAGE_SHIFT) +
PHYS_PFN_OFFSET)
```
where PAGE_OFFSET and PHYS_PFN_OFFSET are the DRAM offset(0x80000000) and
PAGE_SHIFT is 12. This way we obtain 16MB(0x01000000) summed to the base of
DRAM(0x80000000).
When ZERO_PAGE(0) is then used, for example in bio_add_page(), the page
gets an address that is out of DRAM bounds.
So instead of using fake virtual page 0 let's allocate a dedicated
zero_page during paging_init() and assign it to a global 'struct page *
empty_zero_page' the same way mmu.c does and it's the same approach used
in m68k with commit dc068f4621 as discussed here[0]. Then let's move
ZERO_PAGE() definition to the top of pgtable.h to be in common between
mmu.c and nommu.c.
[0]: https://lore.kernel.org/linux-m68k/2a462b23-5b8e-bbf4-ec7d-778434a3b9d7@google.com/T/#m1266ceb63
ad140743174d6b3070364d3c9a5179b
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee47dcfff ]
We must prevent the CPU from reordering the files->count read with the
FD table access like this, on architectures where read-read reordering is
possible:
files_lookup_fd_raw()
close_fd()
put_files_struct()
atomic_read(&files->count)
I would like to mark this for stable, but the stable rules explicitly say
"no theoretical races", and given that the FD table pointer and
files->count are explicitly stored in the same cacheline, this sort of
reordering seems quite unlikely in practice...
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bce9332220 upstream.
proc_skip_spaces() seems to think it is working on C strings, and ends
up being just a wrapper around skip_spaces() with a really odd calling
convention.
Instead of basing it on skip_spaces(), it should have looked more like
proc_skip_char(), which really is the exact same function (except it
skips a particular character, rather than whitespace). So use that as
inspiration, odd coding and all.
Now the calling convention actually makes sense and works for the
intended purpose.
Reported-and-tested-by: Kyle Zeng <zengyhkyle@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6cfaf34be upstream.
proc_get_long() is passed a size_t, but then assigns it to an 'int'
variable for the length. Let's not do that, even if our IO paths are
limited to MAX_RW_COUNT (exactly because of these kinds of type errors).
So do the proper test in the rigth type.
Reported-by: Kyle Zeng <zengyhkyle@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b52be557e2 upstream.
When __do_semtimedop() goes to sleep because it has to wait for a
semaphore value becoming zero or becoming bigger than some threshold, it
links the on-stack sem_queue to the sem_array, then goes to sleep
without holding a reference on the sem_array.
When __do_semtimedop() comes back out of sleep, one of two things must
happen:
a) We prove that the on-stack sem_queue has been disconnected from the
(possibly freed) sem_array, making it safe to return from the stack
frame that the sem_queue exists in.
b) We stabilize our reference to the sem_array, lock the sem_array, and
detach the sem_queue from the sem_array ourselves.
sem_array has RCU lifetime, so for case (b), the reference can be
stabilized inside an RCU read-side critical section by locklessly
checking whether the sem_queue is still connected to the sem_array.
However, the current code does the lockless check on sem_queue before
starting an RCU read-side critical section, so the result of the
lockless check immediately becomes useless.
Fix it by doing rcu_read_lock() before the lockless check. Now RCU
ensures that if we observe the object being on our queue, the object
can't be freed until rcu_read_unlock().
This bug is only hittable on kernel builds with full preemption support
(either CONFIG_PREEMPT or PREEMPT_DYNAMIC with preempt=full).
Fixes: 370b262c89 ("ipc/sem: avoid idr tree lookup for interrupted semop")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23393c6461 upstream.
Currently tpm transactions are executed unconditionally in
tpm_pm_suspend() function, which may lead to races with other tpm
accessors in the system.
Specifically, the hw_random tpm driver makes use of tpm_get_random(),
and this function is called in a loop from a kthread, which means it's
not frozen alongside userspace, and so can race with the work done
during system suspend:
tpm tpm0: tpm_transmit: tpm_recv: error -52
tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics
CPU: 0 PID: 1 Comm: init Not tainted 6.1.0-rc5+ #135
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
Call Trace:
tpm_tis_status.cold+0x19/0x20
tpm_transmit+0x13b/0x390
tpm_transmit_cmd+0x20/0x80
tpm1_pm_suspend+0xa6/0x110
tpm_pm_suspend+0x53/0x80
__pnp_bus_suspend+0x35/0xe0
__device_suspend+0x10f/0x350
Fix this by calling tpm_try_get_ops(), which itself is a wrapper around
tpm_chip_start(), but takes the appropriate mutex.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/all/c5ba47ef-393f-1fba-30bd-1230d1b4b592@suse.cz/
Cc: stable@vger.kernel.org
Fixes: e891db1a18 ("tpm: turn on TPM on suspend for TPM 1.x")
[Jason: reworked commit message, added metadata]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d9f15a9de4 ]
This reverts commit 232ccac1bd.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48d4180939 ]
In a system with a single initiator node, and one or more memory-only
'target' nodes, the memory-only node(s) would fail to register their
initiator node correctly. i.e. in sysfs:
# ls /sys/devices/system/node/node0/access0/targets/
node0
Where as the correct behavior should be:
# ls /sys/devices/system/node/node0/access0/targets/
node0 node1
This happened because hmat_register_target_initiators() uses list_sort()
to sort the initiator list, but the sort comparision function
(initiator_cmp()) is overloaded to also set the node mask's bits.
In a system with a single initiator, the list is singular, and list_sort
elides the comparision helper call. Thus the node mask never gets set,
and the subsequent search for the best initiator comes up empty.
Add a new helper to consume the sorted initiator list, and generate the
nodemask, decoupling it from the overloaded initiator_cmp() comparision
callback. This prevents the singular list corner case naturally, and
makes the code easier to follow as well.
Cc: <stable@vger.kernel.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Liu Shixin <liushixin2@huawei.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Piper <chris.d.piper@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/r/20221116-acpi_hmat_fix-v2-2-3712569be691@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36678f790 ]
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
