commit eb1f822c76 upstream.
In commit a44be64bbe ("ext4: don't clear SB_RDONLY when remounting
r/w until quota is re-enabled") we defer clearing tyhe SB_RDONLY flag
in struct super. However, we didn't defer when we checked sb_rdonly()
to determine the lazy itable init thread should be enabled, with the
next result that the lazy inode table initialization would not be
properly started. This can cause generic/231 to fail in ext4's
nojournal mode.
Fix this by moving when we decide to start or stop the lazy itable
init thread to after we clear the SB_RDONLY flag when we are
remounting the file system read/write.
Fixes a44be64bbe ("ext4: don't clear SB_RDONLY when remounting r/w until...")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230527035729.1001605-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8347b99473 upstream.
Copy the incoming @data comman to an internal buffer so that callers can
put SEV command buffers on the stack without running afoul of
CONFIG_VMAP_STACK=y, i.e. without bombing on vmalloc'd pointers. As of
today, the largest supported command takes a 68 byte buffer, i.e. pretty
much every command can be put on the stack. Because sev_cmd_mutex is
held for the entirety of a transaction, only a single bounce buffer is
required.
Use the internal buffer unconditionally, as the majority of in-kernel
users will soon switch to using the stack. At that point, checking
virt_addr_valid() becomes (negligible) overhead in most cases, and
supporting both paths slightly increases complexity. Since the commands
are all quite small, the cost of the copies is insignificant compared to
the latency of communicating with the PSP.
Allocate a full page for the buffer as opportunistic preparation for
SEV-SNP, which requires the command buffer to be in firmware state for
commands that trigger memory writes from the PSP firmware. Using a full
page now will allow SEV-SNP support to simply transition the page as
needed.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406224952.4177376-5-seanjc@google.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ben Hutchings <benh@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5760dee12 upstream.
WARN on and reject SEV commands that provide a valid data pointer, but do
not have a known, non-zero length. And conversely, reject commands that
take a command buffer but none is provided (data is null).
Aside from sanity checking input, disallowing a non-null pointer without
a non-zero size will allow a future patch to cleanly handle vmalloc'd
data by copying the data to an internal __pa() friendly buffer.
Note, this also effectively prevents callers from using commands that
have a non-zero length and are not known to the kernel. This is not an
explicit goal, but arguably the side effect is a good thing from the
kernel's perspective.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406224952.4177376-4-seanjc@google.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ben Hutchings <benh@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adpt_isr() reads reply addresses from a hardware register, which
should always be within the DMA address range of the device's pool of
reply address buffers. In case the address is out of range, it tries
to muddle on, converting to a virtual address using bus_to_virt().
bus_to_virt() does not take DMA addresses, and it doesn't make sense
to try to handle the completion in this case. Ignore it and continue
looping to service the interrupt. If a completion has been lost then
the SCSI core should eventually time-out and trigger a reset.
There is no corresponding upstream commit, because this driver was
removed upstream.
Fixes: 67af2b060e ("[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt ...")
Signed-off-by: Ben Hutchings <benh@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adpt_i2o_passthru() takes a user-provided message and passes it
through to the hardware with appropriate translation of addresses
and message IDs. It has a number of bugs:
- When a message requires scatter/gather, it doesn't verify that the
offset to the scatter/gather list is less than the message size.
- When a message requires scatter/gather, it overwrites the DMA
addresses with the user-space virtual addresses before unmapping the
DMA buffers.
- It reads the message from user memory multiple times. This allows
user-space to change the message and bypass validation.
- It assumes that the message is at least 4 words long, but doesn't
check that.
I tried fixing these, but even the maintainer of the corresponding
user-space in Debian doesn't have the hardware any more.
Instead, remove the pass-through ioctl (I2OUSRCMD) and supporting
code.
There is no corresponding upstream commit, because this driver was
removed upstream.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: 67af2b060e ("[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt ...")
Signed-off-by: Ben Hutchings <benh@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42d95d1b3a upstream.
The meaning of the 'imply' keyword has changed recently, and neither the
old meaning (select the symbol if its dependencies are met) nor the new
meaning (enable it by default, but let the user set any other setting)
is what we want here.
Work around this by adding two more Kconfig options that lead to
the correct behavior: if DRM_RCAR_USE_CMM and DRM_RCAR_USE_LVDS
are enabled, that portion of the driver becomes usable, and no
configuration results in a link error.
This avoids a link failure:
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_begin':
rcar_du_crtc.c:(.text+0x1444): undefined reference to `rcar_cmm_setup'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_enable':
rcar_du_crtc.c:(.text+0x14d4): undefined reference to `rcar_cmm_enable'
arm-linux-gnueabi-ld: rcar_du_crtc.c:(.text+0x1548): undefined reference to `rcar_cmm_setup'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_disable':
rcar_du_crtc.c:(.text+0x18b8): undefined reference to `rcar_cmm_disable'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_kms.o: in function `rcar_du_modeset_init':
Link: https://lore.kernel.org/all/20200417155553.675905-5-arnd@arndb.de/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7a7d72106 upstream.
FIELD_GET() must only be used with a mask that is a compile-time
constant:
drivers/media/platform/ti-vpe/cal.h: In function 'cal_read_field':
include/linux/compiler_types.h:320:38: error: call to '__compiletime_assert_247' declared with attribute error: FIELD_GET: mask is not constant
include/linux/bitfield.h:46:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
46 | BUILD_BUG_ON_MSG(!__builtin_constant_p(_mask), \
| ^~~~~~~~~~~~~~~~
drivers/media/platform/ti-vpe/cal.h:220:9: note: in expansion of macro 'FIELD_GET'
220 | return FIELD_GET(mask, cal_read(cal, offset));
| ^~~~~~~~~
The problem here is that the function is not always inlined. Mark it
__always_inline to avoid the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c7e66e5fd upstream.
The TIS interrupt handler at least has to read and write the interrupt
status register. In case of SPI both operations result in a call to
tpm_tis_spi_transfer() which uses the bus_lock_mutex of the spi device
and thus must only be called from a sleepable context.
To ensure this request a threaded interrupt handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3981514180 upstream.
Currently, when regmap_raw_write() splits the data, it uses the
max_raw_write value defined for the bus. For any bus that includes
the target register address in the max_raw_write value, the chunked
transmission will always exceed the maximum transmission length.
To avoid this problem, subtract the length of the register and the
padding from the maximum transmission.
Signed-off-by: Jim Wylder <jwylder@google.com
Link: https://lore.kernel.org/r/20230517152444.3690870-2-jwylder@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3d03e8e35 upstream.
Commit ac4e97abce ("scatterlist: sg_set_buf() argument must be in linear
mapping") checks that both the signature and the digest reside in the
linear mapping area.
However, more recently commit ba14a194a4 ("fork: Add generic vmalloced
stack support") made it possible to move the stack in the vmalloc area,
which is not contiguous, and thus not suitable for sg_set_buf() which needs
adjacent pages.
Always make a copy of the signature and digest in the same buffer used to
store the key and its parameters, and pass them to sg_init_one(). Prefer it
to conditionally doing the copy if necessary, to keep the code simple. The
buffer allocated with kmalloc() is in the linear mapping area.
Cc: stable@vger.kernel.org # 4.9.x
Fixes: ba14a194a4 ("fork: Add generic vmalloced stack support")
Link: https://lore.kernel.org/linux-integrity/Y4pIpxbjBdajymBJ@sol.localdomain/
Suggested-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d83013bdf9 upstream.
Selftests are supposed to run on any kernels, including the old ones not
supporting MPTCP.
A new check is then added to make sure MPTCP is supported. If not, the
test stops and is marked as "skipped". Note that this check can also
mark the test as failed if 'SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES' env
var is set to 1: by doing that, we can make sure a test is not being
skipped by mistake.
A new shared file is added here to be able to re-used the same check in
the different selftests we have.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42c4e97e06 upstream.
The Linux Kernel currently only requires make v3.82 while the grouped
target functionality requires make v4.3. Removed the grouped target
introduced in 4ce1f694eb ("selinux: ensure av_permissions.h is
built when needed") as well as the multiple header file targets in
the make rule. This effectively reverts the problem commit.
We will revisit this change when make >= 4.3 is required by the rest
of the kernel.
Cc: stable@vger.kernel.org
Fixes: 4ce1f694eb ("selinux: ensure av_permissions.h is built when needed")
Reported-by: Erwan Velu <e.velu@criteo.com>
Reported-by: Luiz Capitulino <luizcap@amazon.com>
Tested-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ad9b4719f upstream.
When compiling on a MIPS 64-bit machine we get these warnings:
In file included from ./arch/mips/include/asm/cacheflush.h:13,
from ./include/linux/cacheflush.h:5,
from ./include/linux/highmem.h:8,
from ./include/linux/bvec.h:10,
from ./include/linux/blk_types.h:10,
from ./include/linux/blkdev.h:9,
from fs/btrfs/disk-io.c:7:
fs/btrfs/disk-io.c: In function ‘csum_tree_block’:
fs/btrfs/disk-io.c:100:34: error: array subscript 1 is above array bounds of ‘struct page *[1]’ [-Werror=array-bounds]
100 | kaddr = page_address(buf->pages[i]);
| ~~~~~~~~~~^~~
./include/linux/mm.h:2135:48: note: in definition of macro ‘page_address’
2135 | #define page_address(page) lowmem_page_address(page)
| ^~~~
cc1: all warnings being treated as errors
We can check if i overflows to solve the problem. However, this doesn't make
much sense, since i == 1 and num_pages == 1 doesn't execute the body of the loop.
In addition, i < num_pages can also ensure that buf->pages[i] will not cross
the boundary. Unfortunately, this doesn't help with the problem observed here:
gcc still complains.
To fix this add a compile-time condition for the extent buffer page
array size limit, which would eventually lead to eliminating the whole
for loop.
CC: stable@vger.kernel.org # 5.10+
Signed-off-by: pengfuyuan <pengfuyuan@kylinos.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2474e05467 upstream.
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf ("tty: serial: fsl_lpuart: disable the CTS when send break signal")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a99d21cefd upstream.
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
[ 126.980684] UBSAN: array-index-out-of-bounds in drivers/mmc/host/vub300.c:1719:12
[ 126.980709] index -1 is out of range for type 'u32 [4]'
[ 126.980729] CPU: 4 PID: 9 Comm: kworker/u16:0 Tainted: G E 6.3.0-rc4-mtk-local-202304272142 #1
[ 126.980754] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, BIOS BECFL357.86A.0081.2020.0504.1834 05/04/2020
[ 126.980770] Workqueue: kvub300c vub300_cmndwork_thread [vub300]
[ 126.980833] Call Trace:
[ 126.980845] <TASK>
[ 126.980860] dump_stack_lvl+0x48/0x70
[ 126.980895] dump_stack+0x10/0x20
[ 126.980916] ubsan_epilogue+0x9/0x40
[ 126.980944] __ubsan_handle_out_of_bounds+0x70/0x90
[ 126.980979] vub300_cmndwork_thread+0x58e7/0x5e10 [vub300]
[ 126.981018] ? _raw_spin_unlock+0x18/0x40
[ 126.981042] ? finish_task_switch+0x175/0x6f0
[ 126.981070] ? __switch_to+0x42e/0xda0
[ 126.981089] ? __switch_to_asm+0x3a/0x80
[ 126.981129] ? __pfx_vub300_cmndwork_thread+0x10/0x10 [vub300]
[ 126.981174] ? __kasan_check_read+0x11/0x20
[ 126.981204] process_one_work+0x7ee/0x13d0
[ 126.981246] worker_thread+0x53c/0x1240
[ 126.981291] kthread+0x2b8/0x370
[ 126.981312] ? __pfx_worker_thread+0x10/0x10
[ 126.981336] ? __pfx_kthread+0x10/0x10
[ 126.981359] ret_from_fork+0x29/0x50
[ 126.981400] </TASK>
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/048cd6972c50c33c2e8f81d5228fed928519918b.1683987673.git.deren.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32329216ca upstream.
Fixes the following GCC warning:
drivers/net/ethernet/sun/cassini.c:1316:29: error: comparison between two arrays [-Werror=array-compare]
drivers/net/ethernet/sun/cassini.c:3783:34: error: comparison between two arrays [-Werror=array-compare]
Note that 2 arrays should be compared by comparing of their addresses:
note: use ‘&cas_prog_workaroundtab[0] == &cas_prog_null[0]’ to compare the addresses
Signed-off-by: Martin Liska <mliska@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7d63b5089 upstream.
[ Upstream commit 49beadbd47 ]
While the concept of checking for dangling pointers to local variables
at function exit is really interesting, the gcc-12 implementation is not
compatible with reality, and results in false positives.
For example, gcc sees us putting things on a local list head allocated
on the stack, which involves exactly those kinds of pointers to the
local stack entry:
In function ‘__list_add’,
inlined from ‘list_add_tail’ at include/linux/list.h:102:2,
inlined from ‘rebuild_snap_realms’ at fs/ceph/snap.c:434:2:
include/linux/list.h:74:19: warning: storing the address of local variable ‘realm_queue’ in ‘*&realm_27(D)->rebuild_item.prev’ [-Wdangling-pointer=]
74 | new->prev = prev;
| ~~~~~~~~~~^~~~~~
But then gcc - understandably - doesn't really understand the big
picture how the doubly linked list works, so doesn't see how we then end
up emptying said list head in a loop and the pointer we added has been
removed.
Gcc also complains about us (intentionally) using this as a way to store
a kind of fake stack trace, eg
drivers/acpi/acpica/utdebug.c:40:38: warning: storing the address of local variable ‘current_sp’ in ‘acpi_gbl_entry_stack_pointer’ [-Wdangling-pointer=]
40 | acpi_gbl_entry_stack_pointer = ¤t_sp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
which is entirely reasonable from a compiler standpoint, and we may want
to change those kinds of patterns, but not not.
So this is one of those "it would be lovely if the compiler were to
complain about us leaving dangling pointers to the stack", but not this
way.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3128a9d48 upstream.
In builds with -Warray-bounds, casts from smaller objects to larger
objects will produce warnings. These can be overly conservative, but since
-Warray-bounds has been finding legitimate bugs, it is desirable to turn
it on globally. Instead of casting a u32 to a larger object, redefine
the u32 portion of the header to a separate struct that can be used for
both u32 operations and the distinct header fields. Silences this warning:
drivers/net/wireless/ath/ath6kl/htc_mbox.c: In function 'htc_wait_for_ctrl_msg':
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2275:20: error: array subscript 'struct htc_frame_hdr[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Werror=array-bounds]
2275 | if (htc_hdr->eid != ENDPOINT_0)
| ^~
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2264:13: note: while referencing 'look_ahead'
2264 | u32 look_ahead;
| ^~~~~~~~~~
This change results in no executable instruction differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207063538.2767954-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb8441203 upstream.
GCC 11 (incorrectly[1]) assumes that literal values cast to (void *)
should be treated like a NULL pointer with an offset, and raises
diagnostics when doing bounds checking under -Warray-bounds. GCC 12
got "smarter" about finding these:
In function 'rdfs8',
inlined from 'vga_recalc_vertical' at /srv/code/arch/x86/boot/video-mode.c:124:29,
inlined from 'set_mode' at /srv/code/arch/x86/boot/video-mode.c:163:3:
/srv/code/arch/x86/boot/boot.h:114:9: warning: array subscript 0 is outside array bounds of 'u8[0]' {aka 'unsigned char[]'} [-Warray-bounds]
114 | asm volatile("movb %%fs:%1,%0" : "=q" (v) : "m" (*(u8 *)addr));
| ^~~
This has been solved in other places[2] already by using the recently
added absolute_pointer() macro. Do the same here.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578
[2] https://lore.kernel.org/all/20210912160149.2227137-1-linux@roeck-us.net/
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220227195918.705219-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f875850f2 upstream.
For devices not attached to a port multiplier and managed directly by
libata, the device number passed to ata_find_dev() must always be lower
than the maximum number of devices returned by ata_link_max_devices().
That is 1 for SATA devices or 2 for an IDE link with master+slave
devices. This device number is the SCSI device ID which matches these
constraints as the IDs are generated per port and so never exceed the
maximum number of devices for the link being used.
However, for libsas managed devices, SCSI device IDs are assigned per
struct scsi_host, leading to device IDs for SATA devices that can be
well in excess of libata per-link maximum number of devices. This
results in ata_find_dev() to always return NULL for libsas managed
devices except for the first device of the target scsi_host with ID
(device number) equal to 0. This issue is visible by executing the
hdparm utility, which fails. E.g.:
hdparm -i /dev/sdX
/dev/sdX:
HDIO_GET_IDENTITY failed: No message of desired type
Fix this by rewriting ata_find_dev() to ignore the device number for
non-PMP attached devices with a link with at most 1 device, that is SATA
devices. For these, the device number 0 is always used to
return the correct pointer to the struct ata_device of the port link.
This change excludes IDE master/slave setups (maximum number of devices
per link is 2) and port-multiplier attached devices. Also, to be
consistant with the fact that SCSI device IDs and channel numbers used
as device numbers are both unsigned int, change the devno argument of
ata_find_dev() to unsigned int.
Reported-by: Xingui Yang <yangxingui@huawei.com>
Fixes: 41bda9c980 ("libata-link: update hotplug to handle PMP links")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d074ce231 upstream.
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46248400d8 upstream.
The channel's rpmsg object allows new invocations to be made. After old
invocations are already interrupted, the driver shouldn't try to invoke
anymore. Invalidating the rpmsg at the end of the driver removal
function makes it easy to cause a race condition in userspace. Even
closing a file descriptor before the driver finishes its cleanup can
cause an invocation via fastrpc_release_current_dsp_process() and
subsequent timeout.
Invalidate the channel before the invocations are interrupted to make
sure that no invocations can be created to hang after the device closes.
Fixes: c68cfb718c ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230523152550.438363-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb6b53520 upstream.
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Following is the illustration:
CPU1 CPU2
ffs_func_unbind() ffs_ep0_read()
mutex_lock(ffs->mutex)
wait_event(ffs->ev.count)
functionfs_unbind()
mutex_lock(ffs->mutex)
mutex_unlock(ffs->mutex)
ffs_event_add()
<deadlock>
Fix this by moving the event unbind before functionfs_unbind
to ensure the ev.count is incrased properly.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Cc: stable <stable@kernel.org>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20230525092854.7992-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a146eccb68 upstream.
Commit 28d1a7ac2a ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
Fixes: 28d1a7ac2a ("iio: dac: Add AD5758 support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230508040208.12033-1-lukas.bulwahn@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e55245d115 upstream.
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Co-developed-by: Alisa Roman <alisa.roman@analog.com>
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd249b9197 upstream.
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 3bea733ab2 ("USB: wacom tablet driver reorganization")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27b2ed5b6d upstream.
Smatch reports:
drivers/iio/adc/mxs-lradc-adc.c:766 mxs_lradc_adc_probe() warn:
missing unwind goto?
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8fe72b76db ]
There was a bug where this code forgot to unlock the tdev->mutex if the
kzalloc() failed. Fix this issue, by moving the allocation outside the
lock.
Fixes: 2d1e952a2b ("mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb1b7be9b1 ]
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516194625.549249-2-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
