[ Upstream commit d6843d1ee2 ]
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210408143124.b9e68aa98304.I465afb55ca2c7d59f7bf610c6046a1fd732b4c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aca01415e0 ]
This quirk signifies that the adapter cannot do a repeated
START, it always issues a STOP condition after transfers.
Suggested-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0353b4a96b ]
Recently we had an interop issue where RARP packets got suppressed with
bridge neigh suppression enabled, but the check in the code was meant to
suppress GARP. Exclude RARP packets from it which would allow some VMWare
setups to work, to quote the report:
"Those RARP packets usually get generated by vMware to notify physical
switches when vMotion occurs. vMware may use random sip/tip or just use
sip=tip=0. So the RARP packet sometimes get properly flooded by the vtep
and other times get dropped by the logic"
Reported-by: Amer Abdalamer <amer@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a9d54b194 ]
Currently l2cap_chan_set_defaults() reset chan->conf_state to zero.
However, there is a flag CONF_NOT_COMPLETE which is set when
creating the l2cap_chan. It is suggested that the flag should be
cleared when l2cap_chan is ready, but when l2cap_chan_set_defaults()
is called, l2cap_chan is not yet ready. Therefore, we must set this
flag as the default.
Example crash call trace:
__dump_stack lib/dump_stack.c:15 [inline]
dump_stack+0xc4/0x118 lib/dump_stack.c:56
panic+0x1c6/0x38b kernel/panic.c:117
__warn+0x170/0x1b9 kernel/panic.c:471
warn_slowpath_fmt+0xc7/0xf8 kernel/panic.c:494
debug_print_object+0x175/0x193 lib/debugobjects.c:260
debug_object_assert_init+0x171/0x1bf lib/debugobjects.c:614
debug_timer_assert_init kernel/time/timer.c:629 [inline]
debug_assert_init kernel/time/timer.c:677 [inline]
del_timer+0x7c/0x179 kernel/time/timer.c:1034
try_to_grab_pending+0x81/0x2e5 kernel/workqueue.c:1230
cancel_delayed_work+0x7c/0x1c4 kernel/workqueue.c:2929
l2cap_clear_timer+0x1e/0x41 include/net/bluetooth/l2cap.h:834
l2cap_chan_del+0x2d8/0x37e net/bluetooth/l2cap_core.c:640
l2cap_chan_close+0x532/0x5d8 net/bluetooth/l2cap_core.c:756
l2cap_sock_shutdown+0x806/0x969 net/bluetooth/l2cap_sock.c:1174
l2cap_sock_release+0x64/0x14d net/bluetooth/l2cap_sock.c:1217
__sock_release+0xda/0x217 net/socket.c:580
sock_close+0x1b/0x1f net/socket.c:1039
__fput+0x322/0x55c fs/file_table.c:208
____fput+0x17/0x19 fs/file_table.c:244
task_work_run+0x19b/0x1d3 kernel/task_work.c:115
exit_task_work include/linux/task_work.h:21 [inline]
do_exit+0xe4c/0x204a kernel/exit.c:766
do_group_exit+0x291/0x291 kernel/exit.c:891
get_signal+0x749/0x1093 kernel/signal.c:2396
do_signal+0xa5/0xcdb arch/x86/kernel/signal.c:737
exit_to_usermode_loop arch/x86/entry/common.c:243 [inline]
prepare_exit_to_usermode+0xed/0x235 arch/x86/entry/common.c:277
syscall_return_slowpath+0x3a7/0x3b3 arch/x86/entry/common.c:348
int_ret_from_sys_call+0x25/0xa3
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+338f014a98367a08a114@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e127906b68 ]
Commit eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1980d37565 ]
(struct tipc_link_info)->dest is in network order (__be32), so we must
convert the value to network order before assigning. The problem detected
by sparse:
net/tipc/netlink_compat.c:699:24: warning: incorrect type in assignment (different base types)
net/tipc/netlink_compat.c:699:24: expected restricted __be32 [usertype] dest
net/tipc/netlink_compat.c:699:24: got int
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c48950b4 ]
This patch fixes the following message which randomly pops up during
glocktop call:
seq_file: buggy .next function table_seq_next did not update position index
The issue is that seq_read_iter() in fs/seq_file.c also needs an
increment of the index in an non next record case as well which this
patch fixes otherwise seq_read_iter() will print out the above message.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1df83992d9 upstream.
If the total number of commands queried through TPM2_CAP_COMMANDS is
different from that queried through TPM2_CC_GET_CAPABILITY, it indicates
an unknown error. In this case, an appropriate error code -EFAULT should
be returned. However, we currently do not explicitly assign this error
code to 'rc'. As a result, 0 was incorrectly returned.
Cc: stable@vger.kernel.org
Fixes: 58472f5cd4f6("tpm: validate TPM 2.0 commands")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34e5b01186 upstream.
As Or Cohen described:
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
This patch is to fix it by moving the auto_asconf init out of
sctp_init_sock(), by which inet_create()/inet6_create() won't
need to operate it in sctp_destroy_sock() when calling
sk_common_release().
It also makes more sense to do auto_asconf init while binding the
first addr, as auto_asconf actually requires an ANY addr bind,
see it in sctp_addr_wq_timeout_handler().
This addresses CVE-2021-23133.
Fixes: 6102365876 ("bpf: Add new cgroup attach type to enable sock modifications")
Reported-by: Or Cohen <orcohen@paloaltonetworks.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bfe5e8e4 upstream.
This reverts commit b166a20b07.
This one has to be reverted as it introduced a dead lock, as
syzbot reported:
CPU0 CPU1
---- ----
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
lock(&net->sctp.addr_wq_lock);
lock(slock-AF_INET6);
CPU0 is the thread of sctp_addr_wq_timeout_handler(), and CPU1
is that of sctp_close().
The original issue this commit fixed will be fixed in the next
patch.
Reported-by: syzbot+959223586843e69a2674@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1139aeb1c5 upstream.
As of commit 966a967116 ("smp: Avoid using two cache lines for struct
call_single_data"), the smp code prefers 32-byte aligned call_single_data
objects for performance reasons, but the block layer includes an instance
of this structure in the main 'struct request' that is more senstive
to size than to performance here, see 4ccafe0320 ("block: unalign
call_single_data in struct request").
The result is a violation of the calling conventions that clang correctly
points out:
block/blk-mq.c:630:39: warning: passing 8-byte aligned argument to 32-byte aligned parameter 2 of 'smp_call_function_single_async' may result in an unaligned pointer access [-Walign-mismatch]
smp_call_function_single_async(cpu, &rq->csd);
It does seem that the usage of the call_single_data without cache line
alignment should still be allowed by the smp code, so just change the
function prototype so it accepts both, but leave the default alignment
unchanged for the other users. This seems better to me than adding
a local hack to shut up an otherwise correct warning in the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.kernel.org/r/20210505211300.3174456-1-arnd@kernel.org
[nc: Fix conflicts]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d432592f3 upstream.
tcp_set_default_congestion_control() is netns-safe in that it writes
to &net->ipv4.tcp_congestion_control, but it also sets
ca->flags |= TCP_CONG_NON_RESTRICTED which is not namespaced.
This has the unintended side-effect of changing the global
net.ipv4.tcp_allowed_congestion_control sysctl, despite the fact that it
is read-only: 97684f0970 ("net: Make tcp_allowed_congestion_control
readonly in non-init netns")
Resolve this netns "leak" by only allowing the init netns to set the
default algorithm to one that is restricted. This restriction could be
removed if tcp_allowed_congestion_control were namespace-ified in the
future.
This bug was uncovered with
https://github.com/JonathonReinhart/linux-netns-sysctl-verify
Fixes: 6670e15244 ("tcp: Namespace-ify sysctl_tcp_default_congestion_control")
Signed-off-by: Jonathon Reinhart <jonathon.reinhart@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 926ee00ea2 ]
The intent with this code was to return negative error codes but instead
it returns positives.
The problem is how type promotion works with ternary operations. These
functions return long, "ret" is an int and "copied" is a u32. The
negative error code is first cast to u32 so it becomes a high positive and
then cast to long where it's still a positive.
We could fix this by declaring "ret" as a ssize_t but let's just get rid
of the ternaries instead.
Link: https://lkml.kernel.org/r/YIE+/cK1tBzSuQPU@mwanda
Fixes: 5bf2b19320 ("kfifo: add example files to the kernel sample directory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7525858679 ]
In digital_tg_recv_dep_req, it calls nfc_tm_data_received(..,resp).
If nfc_tm_data_received() failed, the callee will free the resp via
kfree_skb() and return error. But in the exit branch, the resp
will be freed again.
My patch sets resp to NULL if nfc_tm_data_received() failed, to
avoid the double free.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34b39efa5a ]
In bnxt_qplib_alloc_res, it calls bnxt_qplib_alloc_dpi_tbl(). Inside
bnxt_qplib_alloc_dpi_tbl, dpit->dbr_bar_reg_iomem is freed via
pci_iounmap() in unmap_io error branch. After the callee returns err code,
bnxt_qplib_alloc_res calls
bnxt_qplib_free_res()->bnxt_qplib_free_dpi_tbl() in the fail branch. Then
dpit->dbr_bar_reg_iomem is freed in the second time by pci_iounmap().
My patch set dpit->dbr_bar_reg_iomem to NULL after it is freed by
pci_iounmap() in the first time, to avoid the double free.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/20210426140614.6722-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d72e7c767 ]
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d13f048dd4 ]
Modify the header size check in geneve6_xmit_skb and geneve_xmit_skb
to use pskb_inet_may_pull rather than pskb_network_may_pull. This fixes
two kernel selftest failures introduced by the commit introducing the
checks:
IPv4 over geneve6: PMTU exceptions
IPv4 over geneve6: PMTU exceptions - nexthop objects
It does this by correctly accounting for the fact that IPv4 packets may
transit over geneve IPv6 tunnels (and vice versa), and still fixes the
uninit-value bug fixed by the original commit.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 6628ddfec7 ("net: geneve: check skb is large enough for IPv4/IPv6 header")
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcabb06bf1 ]
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ba585cc5b ]
UniPhier PXs2 boards have RTL8211E ethernet phy, and the phy have the RX/TX
delays of RGMII interface using pull-ups on the RXDLY and TXDLY pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: e3cc931921 ("ARM: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27537929f3 ]
The problem is that bnxt_show_temp() returns long but "rc" is an int
and "len" is a u32. With ternary operations the type promotion is quite
tricky. The negative "rc" is first promoted to u32 and then to long so
it ends up being a high positive value instead of a a negative as we
intended.
Fix this by removing the ternary.
Fixes: d69753fa1e ("bnxt_en: return proper error codes in bnxt_show_temp")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dd9a40fd6 ]
When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d0 ("ath9k: Check for errors when reading SREV register")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83b8aa520 ]
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfd577acb7 ]
Currently when the call to usb_urb_ep_type_check fails (returning -EINVAL)
the error return path returns -ENOMEM via the exit label "error". Other
uses of the same error exit label set the err variable to -ENOMEM but this
is not being used. I believe the original intent was for the error exit
path to return the value in err rather than the hard coded -ENOMEM, so
return this rather than the hard coded -ENOMEM.
Addresses-Coverity: ("Unused value")
Fixes: 738d9edcfd ("ALSA: usb-audio: Add sanity checks for invalid EPs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210420134719.381409-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e16edc99d6 ]
VMCI feature is not supported in conjunction with the vSphere Fault
Tolerance (FT) feature.
VMware Tools can repeatedly try to create a vsock connection. If FT is
enabled the kernel logs is flooded with the following messages:
qp_alloc_hypercall result = -20
Could not attach to queue pair with -20
"qp_alloc_hypercall result = -20" was hidden by commit e8266c4c33
("VMCI: Stop log spew when qp allocation isn't possible"), but "Could
not attach to queue pair with -20" is still there flooding the log.
Since the error message can be useful in some cases, print it only once.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e083ee8e ]
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92dfb27240 ]
While adding the invalid IRQ check after calling platform_get_irq(),
I managed to overlook that the driver has a complex error path in its
probe() method, thus a simple *return* couldn't be used. Use a proper
*goto* instead!
Fixes: e5b2e3e742 ("i2c: sh7760: add IRQ check")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18fb0bedb5 ]
The signal strength of 5G is quite low, so user can't connect to an AP far
away. New parameters with new format and its parser are updated by the commit
84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser."), but
some parameters are missing. Use this commit to update to the novel parameters
that use new format.
Fixes: 84d26fda52 ("rtlwifi: Update 8821ae new phy parameters and its parser")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219052607.7323-1-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38d0b1c9ce ]
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ecb9dc158 ]
Mirror commit aeba3731b1 ("powerpc/pci: Fix IO space breakage after
of_pci_range_to_resource() change").
Most MIPS platforms do not define PCI_IOBASE, nor implement
pci_address_to_pio(). Moreover, IO_SPACE_LIMIT is 0xffff for most MIPS
platforms. of_pci_range_to_resource passes the _start address_ of the IO
range into pci_address_to_pio, which then checks it against
IO_SPACE_LIMIT and fails, because for MIPS platforms that use
pci-legacy (pci-lantiq, pci-rt3883, pci-mt7620), IO ranges start much
higher than 0xffff.
In fact, pci-mt7621 in staging already works around this problem, see
commit 09dd629eea ("staging: mt7621-pci: fix io space and properly set
resource limits")
So just stop using of_pci_range_to_resource, which does not work for
MIPS.
Fixes PCI errors like:
pci_bus 0000:00: root bus resource [io 0xffffffff]
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 329328ec6a ]
The intel_gvt_init_vgpu_type_groups() function is only called from
intel_gvt_init_device(). If it fails then the intel_gvt_init_device()
prints the error code and propagates it back again. That's a bug
because false is zero/success. The fix is to modify it to return zero
or negative error codes and make everything consistent.
Fixes: c5d71cb317 ("drm/i915/gvt: Move vGPU type related code into gvt file")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/YHaFQtk/DIVYK1u5@mwanda
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5b2e3e742 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: a26c20b1fa ("i2c: Renesas SH7760 I2C master driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5e5f7a8d9 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb6129c328 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: 5faf6e1f58 ("i2c: emev2: add driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
