Set the default for FW_CACHE to n to match Android expectations.
Signed-off-by: Mark Salyzyn <salyzyn@google.com>
Bug: 32180327
Bug: 137566496
Change-Id: I86a28040be07fb2f30125d28f7f379798727785c
By conditionally dropping support for the legacy binding and exporting
the newly introduced 'arm_smmu_impl_init()' function we can allow the
ARM SMMU driver to be built as a module.
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-14-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: Id42da5829cb180966a0d051ec636be0c9f90efed
When removing the SMMU driver, we need to clear any state that we
registered during probe. This includes our bus ops, sysfs entries and
the IOMMU device registered for early firmware probing of masters.
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-13-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: I5dd6e68a609ac60bc704f9f916acc0f31dc1bd67
When removing the SMMUv3 driver, we need to clear any state that we
registered during probe. This includes our bus ops, sysfs entries and
the IOMMU device registered for early firmware probing of masters.
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-11-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: I54372d917c871231ced86250498fe2e45cf39246
Forcefully unbinding the Arm SMMU drivers is a pretty dangerous operation,
since it will likely lead to catastrophic failure for any DMA devices
mastering through the SMMU being unbound. When the driver then attempts
to "handle" the fatal faults, it's very easy to trip over dead data
structures, leading to use-after-free.
On John's machine, he reports that the machine was "unusable" due to
loss of the storage controller following a forced unbind of the SMMUv3
driver:
| # cd ./bus/platform/drivers/arm-smmu-v3
| # echo arm-smmu-v3.0.auto > unbind
| hisi_sas_v2_hw HISI0162:01: CQE_AXI_W_ERR (0x800) found!
| platform arm-smmu-v3.0.auto: CMD_SYNC timeout at 0x00000146
| [hwprod 0x00000146, hwcons 0x00000000]
Prevent this forced unbinding of the drivers by setting "suppress_bind_attrs"
to true.
Link: https://lore.kernel.org/lkml/06dfd385-1af0-3106-4cc5-6a5b8e864759@huawei.com
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-10-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: I8b1c439f7ba11d6fc38cdf686948ef5909871dfb
'bus_set_iommu()' allows IOMMU drivers to register their ops for a given
bus type. Unfortunately, it then doesn't allow them to be removed, which
is necessary for modular drivers to shutdown cleanly so that they can be
reloaded later on.
Allow 'bus_set_iommu()' to take a NULL 'ops' argument, which clear the
ops pointer for the selected bus_type.
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-7-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: Ia89fa2df61d2a9ad04901d4c2e71e293c4c6171d
To avoid accidental removal of an active IOMMU driver module, take a
reference to the driver module in 'iommu_probe_device()' immediately
prior to invoking the '->add_device()' callback and hold it until the
after the device has been removed by '->remove_device()'.
Suggested-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-5-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: I8f6a8aad8c41faa51df9c3a440c8b80c74e3ce8a
To avoid having to export 'pci_request_acs()' to modular IOMMU drivers,
move the call into the 'of_dma_configure()' path in a similar manner to
the way in which ACS is configured when probing via ACPI/IORT.
Signed-off-by: Will Deacon <will@kernel.org>
Bug: 140290589
Link: https://lore.kernel.org/lkml/20191121114918.2293-3-will@kernel.org/
Signed-off-by: Will Deacon <willdeacon@google.com>
Change-Id: I3c689845ca493fbe037a2def2050a089036fb7d3
Pull cramfs fix from Al Viro:
"Regression fix, fallen through the cracks"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cramfs: fix usage on non-MTD device
When both CONFIG_CRAMFS_MTD and CONFIG_CRAMFS_BLOCKDEV are enabled, if
we fail to mount on MTD, we don't try on block device.
Note: this relies upon cramfs_mtd_fill_super() leaving no side
effects on fc state in case of failure; in general, failing
get_tree_...() does *not* mean "fine to try again"; e.g. parsed
options might've been consumed by fill_super callback and freed
on failure.
Fixes: 74f78fc5ef ("vfs: Convert cramfs to use the new mount API")
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull last minute virtio bugfixes from Michael Tsirkin:
"Minor bugfixes all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix shrinker count
virtio_balloon: fix shrinker scan number of pages
virtio_console: allocate inbufs in add_port() only if it is needed
virtio_ring: fix return code on DMA mapping fails
Pull input fix from Dmitry Torokhov:
"Just a single revert as RMI mode should not have been enabled for this
model [yet?]"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - enable RMI mode for X1 Extreme 2nd Generation"
This reverts commit 68b9c5066e39af41d3448abfc887c77ce22dd64d.
Ugh, I really dropped the ball on this one :\. So as it turns out RMI4
works perfectly fine on the X1 Extreme Gen 2 except for one thing I
didn't notice because I usually use the trackpoint: clicking with the
touchpad. Somehow this is broken, in fact we don't even seem to indicate
BTN_LEFT as a valid event type for the RMI4 touchpad. And, I don't even
see any RMI4 events coming from the touchpad when I press down on it.
This only seems to work for PS/2 mode.
Since that means we have a regression, and PS/2 mode seems to work fine
for the time being - revert this for now. We'll have to do a more
thorough investigation on this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191119234534.10725-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull networking fixes from David Miller:
1) Validate tunnel options length in act_tunnel_key, from Xin Long.
2) Fix DMA sync bug in gve driver, from Adi Suresh.
3) TSO kills performance on some r8169 chips due to HW issues, disable
by default in that case, from Corinna Vinschen.
4) Fix clock disable mismatch in fec driver, from Chubong Yuan.
5) Fix interrupt status bits define in hns3 driver, from Huazhong Tan.
6) Fix workqueue deadlocks in qeth driver, from Julian Wiedmann.
7) Don't napi_disable() twice in r8152 driver, from Hayes Wang.
8) Fix SKB extension memory leak, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
r8152: avoid to call napi_disable twice
MAINTAINERS: Add myself as maintainer of virtio-vsock
udp: drop skb extensions before marking skb stateless
net: rtnetlink: prevent underflows in do_setvfinfo()
can: m_can_platform: remove unnecessary m_can_class_resume() call
can: m_can_platform: set net_device structure as driver data
hv_netvsc: Fix send_table offset in case of a host bug
hv_netvsc: Fix offset usage in netvsc_send_table()
net-ipv6: IPV6_TRANSPARENT - check NET_RAW prior to NET_ADMIN
sfc: Only cancel the PPS workqueue if it exists
nfc: port100: handle command failure cleanly
net-sysfs: fix netdev_queue_add_kobject() breakage
r8152: Re-order napi_disable in rtl8152_close
net: qca_spi: Move reset_count to struct qcaspi
net: qca_spi: fix receive buffer size check
net/ibmvnic: Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
Revert "net/ibmvnic: Fix EOI when running in XIVE mode"
net/mlxfw: Verify FSM error code translation doesn't exceed array size
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix auto group size calculation
...
By default s_maxbytes is set to MAX_NON_LFS, which limits the usable
file size to 2GB, enforced by the vfs.
Commit b9b1f8d593 ("AFS: write support fixes") added support for the
64-bit fetch and store server operations, but did not change this value.
As a result, attempts to write past the 2G mark result in EFBIG errors:
$ dd if=/dev/zero of=foo bs=1M count=1 seek=2048
dd: error writing 'foo': File too large
Set s_maxbytes to MAX_LFS_FILESIZE.
Fixes: b9b1f8d593 ("AFS: write support fixes")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Servers sending callback breaks to the YFS_CM_SERVICE service may
send up to YFSCBMAX (1024) fids in a single RPC. Anything over
AFSCBMAX (50) will cause the assert in afs_break_callbacks to trigger.
Remove the assert, as the count has already been checked against
the appropriate max values in afs_deliver_cb_callback and
afs_deliver_yfs_cb_callback.
Fixes: 35dbfba311 ("afs: Implement the YFS cache manager service")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 8481141246 ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge misc fixes from Andrew Morton:
"Three fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/ksm.c: don't WARN if page is still mapped in remove_stable_node()
mm/memory_hotplug: don't access uninitialized memmaps in shrink_zone_span()
Revert "fs: ocfs2: fix possible null-pointer dereferences in ocfs2_xa_prepare_entry()"
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-22
this is a pull request of 2 patches for net/master, if possible for the
current release cycle. Otherwise these patches should hit v5.4 via the
stable tree.
Both patches of this pull request target the m_can driver. Pankaj Sharma
fixes the fallout in the m_can_platform part, which appeared with the
introduction of the m_can platform framework.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I'm actively working on vsock and virtio/vhost transports,
Stefan suggested to help him to maintain it.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once udp stack has set the UDP_SKB_IS_STATELESS flag, later skb free
assumes all skb head state has been dropped already.
This will leak the extension memory in case the skb has extensions other
than the ipsec secpath, e.g. bridge nf data.
To fix this, set the UDP_SKB_IS_STATELESS flag only if we don't have
extensions or if the extension space can be free'd.
Fixes: 895b5c9f20 ("netfilter: drop bridge nf reset from nf_reset")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Byron Stanoszek <gandalf@winds.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull power management regression fix from Rafael Wysocki:
"Fix problems with switching cpufreq drivers on some x86 systems with
ACPI (and with changing the operation modes of the intel_pstate driver
on those systems) introduced by recent changes related to the
management of frequency limits in cpufreq"
* tag 'pm-5.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: QoS: Invalidate frequency QoS requests after removal
Pull drm fixes from Dave Airlie:
"Two sets of fixes in here, one for amdgpu, and one for i915.
The amdgpu ones are pretty small, i915's CI system seems to have a few
problems in the last week or so, there is one major regression fix for
fb_mmap, but there are a bunch of other issues fixed in there as well,
oops, screen flashes and rcu related.
amdgpu:
- Remove experimental flag for navi14
- Fix confusing power message failures on older VI parts
- Hang fix for gfxoff when using the read register interface
- Two stability regression fixes for Raven
i915:
- Fix kernel oops on dumb_create ioctl on no crtc situation
- Fix bad ugly colored flash on VLV/CHV related to gamma LUT update
- Fix unity of the frequencies reported on PMU
- Fix kernel oops on set_page_dirty using better locks around it
- Protect the request pointer with RCU to prevent it being freed
while we might need still
- Make pool objects read-only
- Restore physical addresses for fb_map to avoid corrupted page
table"
* tag 'drm-fixes-2019-11-22' of git://anongit.freedesktop.org/drm/drm:
drm/i915/fbdev: Restore physical addresses for fb_mmap()
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: disable gfxoff when using register read interface
drm/amd/powerplay: correct fine grained dpm force level setting
drm/amd/powerplay: issue no PPSMC_MSG_GetCurrPkgPwr on unsupported ASICs
drm/amdgpu: remove experimental flag for Navi14
drm/i915: make pool objects read-only
drm/i915: Protect request peeking with RCU
drm/i915/userptr: Try to acquire the page lock around set_page_dirty()
drm/i915/pmu: "Frequency" is reported as accumulated cycles
drm/i915: Preload LUTs if the hw isn't currently using them
drm/i915: Don't oops in dumb_create ioctl if we have no crtcs
It's possible to hit the WARN_ON_ONCE(page_mapped(page)) in
remove_stable_node() when it races with __mmput() and squeezes in
between ksm_exit() and exit_mmap().
WARNING: CPU: 0 PID: 3295 at mm/ksm.c:888 remove_stable_node+0x10c/0x150
Call Trace:
remove_all_stable_nodes+0x12b/0x330
run_store+0x4ef/0x7b0
kernfs_fop_write+0x200/0x420
vfs_write+0x154/0x450
ksys_write+0xf9/0x1d0
do_syscall_64+0x99/0x510
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Remove the warning as there is nothing scary going on.
Link: http://lkml.kernel.org/r/20191119131850.5675-1-aryabinin@virtuozzo.com
Fixes: cbf86cfe04 ("ksm: remove old stable nodes more thoroughly")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function m_can_runtime_resume() is getting recursively called from
m_can_class_resume(). This results in a lock up.
We need not call m_can_class_resume() during m_can_runtime_resume().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Haiyang Zhang says:
====================
hv_netvsc: Fix send indirection table offset
Fix send indirection table offset issues related to guest and
host bugs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If negotiated NVSP version <= NVSP_PROTOCOL_VERSION_6, the offset may
be wrong (too small) due to a host bug. This can cause missing the
end of the send indirection table, and add multiple zero entries from
leading zeros before the data region. This bug adds extra burden on
channel 0.
So fix the offset by computing it from the data structure sizes. This
will ensure netvsc driver runs normally on unfixed hosts, and future
fixed hosts.
Fixes: 5b54dac856 ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reach the data region, the existing code adds offset in struct
nvsp_5_send_indirect_table on the beginning of this struct. But the
offset should be based on the beginning of its container,
struct nvsp_message. This bug causes the first table entry missing,
and adds an extra zero from the zero pad after the data region.
This can put extra burden on the channel 0.
So, correct the offset usage. Also add a boundary check to ensure
not reading beyond data region.
Fixes: 5b54dac856 ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
