[ Upstream commit 91b6dbced0ef1d680afdd69b14fc83d50ebafaf3 ]
When netfilter defrag hooks are loaded (due to the presence of conntrack
rules, for example), fragmented packets entering the bridge will be
defragged by the bridge's pre-routing hook (br_nf_pre_routing() ->
ipv4_conntrack_defrag()).
Later on, in the bridge's post-routing hook, the defragged packet will
be fragmented again. If the size of the largest fragment is larger than
what the kernel has determined as the destination MTU (using
ip_skb_dst_mtu()), the defragged packet will be dropped.
Before commit ac6627a28d ("net: ipv4: Consolidate ipv4_mtu and
ip_dst_mtu_maybe_forward"), ip_skb_dst_mtu() would return dst_mtu() as
the destination MTU. Assuming the dst entry attached to the packet is
the bridge's fake rtable one, this would simply be the bridge's MTU (see
fake_mtu()).
However, after above mentioned commit, ip_skb_dst_mtu() ends up
returning the route's MTU stored in the dst entry's metrics. Ideally, in
case the dst entry is the bridge's fake rtable one, this should be the
bridge's MTU as the bridge takes care of updating this metric when its
MTU changes (see br_change_mtu()).
Unfortunately, the last operation is a no-op given the metrics attached
to the fake rtable entry are marked as read-only. Therefore,
ip_skb_dst_mtu() ends up returning 1500 (the initial MTU value) and
defragged packets are dropped during fragmentation when dealing with
large fragments and high MTU (e.g., 9k).
Fix by moving the fake rtable entry's metrics to be per-bridge (in a
similar fashion to the fake rtable entry itself) and marking them as
writable, thereby allowing MTU changes to be reflected.
Fixes: 62fa8a846d ("net: Implement read-only protection and COW'ing of metrics.")
Fixes: 33eb9873a2 ("bridge: initialize fake_rtable metrics")
Reported-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Closes: https://lore.kernel.org/netdev/PH0PR10MB4504888284FF4CBA648197D0ACB82@PH0PR10MB4504.namprd10.prod.outlook.com/
Tested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250515084848.727706-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7af8479d9eb4319b4ba7b47a8c4d2c55af1c31e1 ]
l2cap_check_enc_key_size shall check the security level of the
l2cap_chan rather than the hci_conn since for incoming connection
request that may be different as hci_conn may already been
encrypted using a different security level.
Fixes: 522e9ed157e3 ("Bluetooth: l2cap: Check encryption key size on incoming connection")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b91fda3a1f044141e1e615456ff62508c32b202 ]
Prior to this patch, the mark is sanitized (applying the state's mask to
the state's value) only on inserts when checking if a conflicting XFRM
state or policy exists.
We discovered in Cilium that this same sanitization does not occur
in the hot-path __xfrm_state_lookup. In the hot-path, the sk_buff's mark
is simply compared to the state's value:
if ((mark & x->mark.m) != x->mark.v)
continue;
Therefore, users can define unsanitized marks (ex. 0xf42/0xf00) which will
never match any packet.
This commit updates __xfrm_state_insert and xfrm_policy_insert to store
the sanitized marks, thus removing this footgun.
This has the side effect of changing the ip output, as the
returned mark will have the mask applied to it when printed.
Fixes: 3d6acfa764 ("xfrm: SA lookups with mark")
Signed-off-by: Paul Chaignon <paul.chaignon@gmail.com>
Signed-off-by: Louis DeLosSantos <louis.delos.devel@gmail.com>
Co-developed-by: Louis DeLosSantos <louis.delos.devel@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98e6da673cc6dd46ca9a599802bd2c8f83606710 ]
The D1/R528/T113 SoCs have a hidden divider of 2 in the MMC mod clocks,
just as other recent SoCs. So far we did not describe that, which led
to the resulting MMC clock rate to be only half of its intended value.
Use a macro that allows to describe a fixed post-divider, to compensate
for that divisor.
This brings the MMC performance on those SoCs to its expected level,
so about 23 MB/s for SD cards, instead of the 11 MB/s measured so far.
Fixes: 35b97bb941 ("clk: sunxi-ng: Add support for the D1 SoC clocks")
Reported-by: Kuba Szczodrzyński <kuba@szczodrzynski.pl>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20250501120631.837186-1-andre.przywara@arm.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca45af0a56d00b86285d6fdd720dca3215059a7 ]
Recent change to handle platforms with only single power domain broke
pronto-v3 which requires power domains and doesn't have fallback voltage
regulators in case power domains are missing. Add a check to verify
the number of fallback voltage regulators before using the code which
handles single power domain situation.
Fixes: 65991ea8a6d1 ("remoteproc: qcom_wcnss: Handle platforms with only single power domain")
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sdm632-fairphone-fp3
Link: https://lore.kernel.org/r/20250511234026.94735-1-matti.lehtimaki@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b022f59725 ]
Define idxd_copy_cr() to copy completion record to fault address in
user address that is found by work queue (wq) and PASID.
It will be used to write the user's completion record that the hardware
device is not able to write due to user completion record page fault.
An xarray is added to associate the PASID and mm with the
struct idxd_user_context so mm can be found by PASID and wq.
It is called when handling the completion record fault in a kernel thread
context. Switch to the mm using kthread_use_vm() and copy the
completion record to the mm via copy_to_user(). Once the copy is
completed, switch back to the current mm using kthread_unuse_mm().
Suggested-by: Christoph Hellwig <hch@infradead.org>
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Suggested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Zhu <tony.zhu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20230407203143.2189681-9-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 8dfa57aabff6 ("dmaengine: idxd: Fix allowing write() from different address spaces")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 028363685bd0b7a19b4a820f82dd905b1dc83999 ]
The current scheme for caching the encap socket can lead to reference
leaks when we try to delete the netns.
The reference chain is: xfrm_state -> enacp_sk -> netns
Since the encap socket is a userspace socket, it holds a reference on
the netns. If we delete the espintcp state (through flush or
individual delete) before removing the netns, the reference on the
socket is dropped and the netns is correctly deleted. Otherwise, the
netns may not be reachable anymore (if all processes within the ns
have terminated), so we cannot delete the xfrm state to drop its
reference on the socket.
This patch results in a small (~2% in my tests) performance
regression.
A GC-type mechanism could be added for the socket cache, to clear
references if the state hasn't been used "recently", but it's a lot
more complex than just not caching the socket.
Fixes: e27cca96cd ("xfrm: add espintcp (RFC 8229)")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 250cf3693060a5f803c5f1ddc082bb06b16112a9 ]
... or we risk stealing final mntput from sync umount - raising mnt_count
after umount(2) has verified that victim is not busy, but before it
has set MNT_SYNC_UMOUNT; in that case __legitimize_mnt() doesn't see
that it's safe to quietly undo mnt_count increment and leaves dropping
the reference to caller, where it'll be a full-blown mntput().
Check under mount_lock is needed; leaving the current one done before
taking that makes no sense - it's nowhere near common enough to bother
with.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90989869baae47ee2aa3bcb6f6eb9fbbe4287958 ]
Make xenbus_init() allow a non-local xenstore for a PVH dom0 - it is
currently forced to XS_LOCAL. With Hyperlaunch booting dom0 and a
xenstore stubdom, dom0 can be handled as a regular XS_HVM following the
late init path.
Ideally we'd drop the use of xen_initial_domain() and just check for the
event channel instead. However, ARM has a xen,enhanced no-xenstore
mode, where the event channel and PFN would both be 0. Retain the
xen_initial_domain() check, and use that for an additional check when
the event channel is 0.
Check the full 64bit HVM_PARAM_STORE_EVTCHN value to catch the off
chance that high bits are set for the 32bit event channel.
Signed-off-by: Jason Andryuk <jason.andryuk@amd.com>
Change-Id: I5506da42e4c6b8e85079fefb2f193c8de17c7437
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20250506204456.5220-1-jason.andryuk@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f024d3a8ded0d8d2129ae123d7a5305c29ca44ce ]
syzbot complains about the cached sq head read, and it's totally right.
But we don't need to care, it's just reading fdinfo, and reading the
CQ or SQ tail/head entries are known racy in that they are just a view
into that very instant and may of course be outdated by the time they
are reported.
Annotate both the SQ head and CQ tail read with data_race() to avoid
this syzbot complaint.
Link: https://lore.kernel.org/io-uring/6811f6dc.050a0220.39e3a1.0d0e.GAE@google.com/
Reported-by: syzbot+3e77fd302e99f5af9394@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e56088a13708757da68ad035269d69b93ac8c389 ]
The public datasheets of the following Amlogic SoCs describe a typical
resistor value for the built-in pull up/down resistor:
- Meson8/8b/8m2: not documented
- GXBB (S905): 60 kOhm
- GXL (S905X): 60 kOhm
- GXM (S912): 60 kOhm
- G12B (S922X): 60 kOhm
- SM1 (S905D3): 60 kOhm
The public G12B and SM1 datasheets additionally state min and max
values:
- min value: 50 kOhm for both, pull-up and pull-down
- max value for the pull-up: 70 kOhm
- max value for the pull-down: 130 kOhm
Use 60 kOhm in the pinctrl-meson driver as well so it's shown in the
debugfs output. It may not be accurate for Meson8/8b/8m2 but in reality
60 kOhm is closer to the actual value than 1 Ohm.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/20250329190132.855196-1-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 749b5b279e5636cdcef51e15d67b77162cca6caa ]
We have a few reports of sc7180-trogdor-pompom devices that have a
panel in them that IDs as STA 0x0004 and has the following raw EDID:
00 ff ff ff ff ff ff 00 4e 81 04 00 00 00 00 00
10 20 01 04 a5 1a 0e 78 0a dc dd 96 5b 5b 91 28
1f 52 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 8e 1c 56 a0 50 00 1e 30 28 20
55 00 00 90 10 00 00 18 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fe
00 31 31 36 4b 48 44 30 32 34 30 30 36 0a 00 e6
We've been unable to locate a datasheet for this panel and our partner
has not been responsive, but all Starry eDP datasheets that we can
find agree on the same timing (delay_100_500_e200) so it should be
safe to use that here instead of the super conservative timings. We'll
still go a little extra conservative and allow `hpd_absent` of 200
instead of 100 because that won't add any real-world delay in most
cases.
We'll associate the string from the EDID ("116KHD024006") with this
panel. Given that the ID is the suspicious value of 0x0004 it seems
likely that Starry doesn't always update their IDs but the string will
still work to differentiate if we ever need to in the future.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109142853.1.Ibcc3009933fd19507cc9c713ad0c99c7a9e4fe17@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfffb317519f88534bb82797f055f0a2fd867e7b ]
When using nvmem, ath9k could potentially be loaded before nvmem, which
loads after mtd. This is an issue if DT contains an nvmem mac address.
If nvmem is not ready in time for ath9k, -EPROBE_DEFER is returned. Pass
it to _probe so that ath9k can properly grab a potentially present MAC
address.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241105222326.194417-1-rosenp@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00451eb3bec763f708e7e58326468c1e575e5a66 ]
Some users want to plug two identical USB devices at the same time.
This static variable could theoretically cause them to use incorrect
TX power values.
Move the variable to the caller and pass a pointer to it to
rtw8822b_set_tx_power_index_by_rate().
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/8a60f581-0ab5-4d98-a97d-dd83b605008f@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3e28feca7ac8c6cf2a390dbbe1f97e3feb7f36 ]
Occasionally there is an EPROTO error during firmware download.
This error is converted to EAGAIN in the download function.
But nobody tries again and so device probe fails.
Implement download retry to fix this.
This error was observed (and fix tested) on a tbs2910 board [1]
with an embedded RTL8188EU (0bda:8179) device behind a USB hub.
[1] arch/arm/boot/dts/nxp/imx/imx6q-tbs2910.dts
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250127194828.599379-1-smoch@web.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46dcf85566170d4528b842bf83ffc350d71771fa ]
IBS Op uses two counters: MaxCnt and CurCnt. MaxCnt is programmed with
the desired sample period. IBS hw generates sample when CurCnt reaches
to MaxCnt. The size of these counter used to be 20 bits but later they
were extended to 27 bits. The 7 bit extension is indicated by CPUID
Fn8000_001B_EAX[6 / OpCntExt].
perf_ibs->cnt_mask variable contains bit masks for MaxCnt and CurCnt.
But IBS driver does not set upper 7 bits of CurCnt in cnt_mask even
when OpCntExt CPUID bit is set. Fix this.
IBS driver uses cnt_mask[CurCnt] bits only while disabling an event.
Fortunately, CurCnt bits are not read from MSR while re-enabling the
event, instead MaxCnt is programmed with desired period and CurCnt is
set to 0. Hence, we did not see any issues so far.
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/r/20250115054438.1021-5-ravi.bangoria@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0053f7d39d491b6138d7c526876d13885cbb65f1 ]
The `readlink(path, buf, sizeof(buf))` call reads at most sizeof(buf)
bytes and *does not* append null-terminator to buf. With respect to
that, fix two pieces in get_fd_type:
1. Change the truncation check to contain sizeof(buf) rather than
sizeof(path).
2. Append null-terminator to buf.
Reported by Coverity.
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Quentin Monnet <qmo@kernel.org>
Link: https://lore.kernel.org/bpf/20250129071857.75182-1-vmalik@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81202906b5cd56db403e95db3d29c9dfc8c74c1 ]
The ast driver looks up supplied display modes from an internal list of
display modes supported by the VBIOS.
Do not use the crtc_-prefixed display values from struct drm_display_mode
for looking up the VBIOS mode. The fields contain raw values that the
driver programs to hardware. They are affected by display settings like
double-scan or interlace.
Instead use the regular vdisplay and hdisplay fields for lookup. As the
programmed values can now differ from the values used for lookup, set
struct drm_display_mode.crtc_vdisplay and .crtc_hdisplay from the VBIOS
mode.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-9-tzimmermann@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d73a4bfa2881a6859b384b75a414c33d4898b055 ]
Since "LED_KANA" was defined as "0x04", the shift number should be "4".
Signed-off-by: junan <junan76@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7081dc75df79696d8322d01821c28e53416c932c ]
Some of the allowed operations put the tape into a known position to
continue operation assuming only the tape position has changed. But reset
sets partition, density and block size to drive default values. These
should be restored to the values before reset.
Normally the current block size and density are stored by the drive. If
the settings have been changed, the changed values have to be saved by the
driver across reset.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Link: https://lore.kernel.org/r/20250120194925.44432-2-Kai.Makisara@kolumbus.fi
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56c3d809b7b450379162d0b8a70bbe71ab8db706 ]
After a port swap between separate fabrics, there may be multiple nodes in
the vport's fc_nodes list with the same fabric well known address.
Duplication is temporary and eventually resolves itself after dev_loss_tmo
expires, but nameserver queries may still occur before dev_loss_tmo. This
possibly results in returning stale fabric ndlp objects. Fix by adding an
nlp_state check to ensure the ndlp search routine returns the correct newer
allocated ndlp fabric object.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20250131000524.163662-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3a392bdd31adc474f1009ee85c13fdd01fe800d ]
Previous implementation assumes that there is 1:1 matching between
vectors and queues. It isn't always true.
Get minimum value from Rx/Tx queues to determine combined queues number.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ce939a0fa194939cc1f92dbd8bc1a7806e7d40a ]
The event may have been updated in the PMU-specific implementation,
e.g., Intel PEBS counters snapshotting. The common code should not
read and overwrite the value.
The PERF_SAMPLE_READ in the data->sample_type can be used to detect
whether the PMU-specific value is available. If yes, avoid the
pmu->read() in the common code. Add a new flag, skip_read, to track the
case.
Factor out a perf_pmu_read() to clean up the code.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250121152303.3128733-3-kan.liang@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad6b5b73ff565e88aca7a7d1286788d80c97ba71 ]
rcu_all_qs() is defined for !CONFIG_PREEMPT_RCU but the declaration
is conditioned on CONFIG_PREEMPTION.
With CONFIG_PREEMPT_LAZY, CONFIG_PREEMPTION=y does not imply
CONFIG_PREEMPT_RCU=y.
Decouple the two.
Cc: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcf0e25ad4c8d14d2faab4d9a17040f31efce205 ]
rcu_read_unlock_strict() can be called with preemption enabled
which can make for an unstable rdp and a racy norm value.
Fix this by dropping the preempt-count in __rcu_read_unlock()
after the call to rcu_read_unlock_strict(), adjusting the
preempt-count check appropriately.
Suggested-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83b28cfe796464ebbde1cf7916c126da6d572685 ]
With PREEMPT_RCU=n, cond_resched() provides urgently needed quiescent
states for read-side critical sections via rcu_all_qs().
One reason why this was needed: lacking preempt-count, the tick
handler has no way of knowing whether it is executing in a
read-side critical section or not.
With (PREEMPT_LAZY=y, PREEMPT_DYNAMIC=n), we get (PREEMPT_COUNT=y,
PREEMPT_RCU=n). In this configuration cond_resched() is a stub and
does not provide quiescent states via rcu_all_qs().
(PREEMPT_RCU=y provides this information via rcu_read_unlock() and
its nesting counter.)
So, use the availability of preempt_count() to report quiescent states
in rcu_flavor_sched_clock_irq().
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6205f8215f12a96518ac9469ff76294ae7bd612 ]
The 'used' and 'updated' fields in the FDB entry structure can be
accessed concurrently by multiple threads, leading to reports such as
[1]. Can be reproduced using [2].
Suppress these reports by annotating these accesses using
READ_ONCE() / WRITE_ONCE().
[1]
BUG: KCSAN: data-race in vxlan_xmit / vxlan_xmit
write to 0xffff942604d263a8 of 8 bytes by task 286 on cpu 0:
vxlan_xmit+0xb29/0x2380
dev_hard_start_xmit+0x84/0x2f0
__dev_queue_xmit+0x45a/0x1650
packet_xmit+0x100/0x150
packet_sendmsg+0x2114/0x2ac0
__sys_sendto+0x318/0x330
__x64_sys_sendto+0x76/0x90
x64_sys_call+0x14e8/0x1c00
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
read to 0xffff942604d263a8 of 8 bytes by task 287 on cpu 2:
vxlan_xmit+0xadf/0x2380
dev_hard_start_xmit+0x84/0x2f0
__dev_queue_xmit+0x45a/0x1650
packet_xmit+0x100/0x150
packet_sendmsg+0x2114/0x2ac0
__sys_sendto+0x318/0x330
__x64_sys_sendto+0x76/0x90
x64_sys_call+0x14e8/0x1c00
do_syscall_64+0x9e/0x1a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
value changed: 0x00000000fffbac6e -> 0x00000000fffbac6f
Reported by Kernel Concurrency Sanitizer on:
CPU: 2 UID: 0 PID: 287 Comm: mausezahn Not tainted 6.13.0-rc7-01544-gb4b270f11a02 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014
[2]
#!/bin/bash
set +H
echo whitelist > /sys/kernel/debug/kcsan
echo !vxlan_xmit > /sys/kernel/debug/kcsan
ip link add name vx0 up type vxlan id 10010 dstport 4789 local 192.0.2.1
bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 198.51.100.1
taskset -c 0 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q &
taskset -c 2 mausezahn vx0 -a own -b 00:11:22:33:44:55 -c 0 -q &
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250204145549.1216254-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f1361f862a68063f37362f1beb400e78e289581 ]
There is no CSID TPG on some SoCs, so the v4l2 ctrl in CSID driver
shouldn't be registered. Checking the supported TPG modes to indicate
if the TPG hardware exists or not and only registering v4l2 ctrl for
CSID only when the TPG hardware is present.
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8df0f002827e18632dcd986f7546c1abf1953a6f ]
The expression PCC_NUM_RETRIES * pcc_chan->latency is currently being
evaluated using 32-bit arithmetic.
Since a value of type 'u64' is used to store the eventual result,
and this result is later sent to the function usecs_to_jiffies with
input parameter unsigned int, the current data type is too wide to
store the value of ctx->usecs_lat.
Change the data type of "usecs_lat" to a more suitable (narrower) type.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Vatoropin <a.vatoropin@crpt.ru>
Link: https://lore.kernel.org/r/20250204095400.95013-1-a.vatoropin@crpt.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52b10b591f83dc6d9a1d6c2dc89433470a787ecd ]
Update some RCGs on the sm8250 camera clock controller to use
clk_rcg2_shared_ops. The shared_ops ensure the RCGs get parked
to the XO during clock disable to prevent the clocks from locking up
when the GDSC is enabled. These mirror similar fixes for other controllers
such as commit e5c359f70e ("clk: qcom: camcc: Update the clock ops for
the SC7180").
Signed-off-by: Jordan Crouse <jorcrous@amazon.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250122222612.32351-1-jorcrous@amazon.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e8243025cc06abc975c876dffda052073207ab3 ]
After the firmware is uploaded, download_firmware_validate() checks some
bits in REG_MCUFW_CTRL to see if everything went okay. The
RTL8814AU power on sequence sets bits 13 and 12 to 2, which this
function does not expect, so it thinks the firmware upload failed.
Make download_firmware_validate() ignore bits 13 and 12.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/049d2887-22fc-47b7-9e59-62627cb525f8@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 848b09d53d923b4caee5491f57a5c5b22d81febc ]
The Dell AW1022z is an RTL8156B based 2.5G Ethernet controller.
Add the vendor and product ID values to the driver. This makes Ethernet
work with the adapter.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20250206224033.980115-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
