commit 13dbc954b3 upstream.
dtbs_check currently complains that:
arch/arm/boot/dts/bcm2711-rpi-4-b.dts:220.10-231.4: Warning
(pci_device_reg): /scb/pcie@7d500000/pci@1,0: PCI unit address format
error, expected "0,0"
Unsurprisingly pci@0,0 is the right address, as illustrated by its reg
property:
&pcie0 {
pci@0,0 {
/*
* As defined in the IEEE Std 1275-1994 document,
* reg is a five-cell address encoded as (phys.hi
* phys.mid phys.lo size.hi size.lo). phys.hi
* should contain the device's BDF as 0b00000000
* bbbbbbbb dddddfff 00000000. The other cells
* should be zero.
*/
reg = <0 0 0 0 0>;
};
};
The device is clearly 0. So fix it.
Also add a missing 'device_type = "pci"'.
Fixes: 258f92d2f8 ("ARM: dts: bcm2711: Add reset controller to xHCI node")
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210831125843.1233488-1-nsaenzju@redhat.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f565d0ead upstream.
When OP-TEE driver is built as a module, OP-TEE client devices
registered on TEE bus during probe should be unregistered during
optee_remove. So implement optee_unregister_devices() accordingly.
Fixes: c3fa24af92 ("tee: optee: add TEE bus device enumeration support")
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a913270e5 upstream.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e081102f30 upstream.
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89a86da5cb upstream.
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f729a592ad upstream.
SYNC_STATE_ONLY device links intentionally allow cycles because cyclic
sync_state() dependencies are valid and necessary.
However a SYNC_STATE_ONLY device link where the consumer and the supplier
are the same device is pointless because the device link would be deleted
as soon as the device probes (because it's also the consumer) and won't
affect when the sync_state() callback is called. It's a waste of CPU cycles
and memory to create this device link. So reject any attempts to create
such a device link.
Fixes: 05ef983e0d ("driver core: Add device link support for SYNC_STATE_ONLY flag")
Cc: stable <stable@vger.kernel.org>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210929190549.860541-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f779e1d35 upstream.
When an interrupt is passed through, the KVM XIVE device calls the
set_vcpu_affinity() handler which raises the P bit to mask the
interrupt and to catch any in-flight interrupts while routing the
interrupt to the guest.
On the guest side, drivers (like some Intels) can request at probe
time some MSIs and call synchronize_irq() to check that there are no
in flight interrupts. This will call the XIVE get_irqchip_state()
handler which will always return true as the interrupt P bit has been
set on the host side and lock the CPU in an infinite loop.
Fix that by discarding disabled interrupts in get_irqchip_state().
Fixes: da15c03b04 ("powerpc/xive: Implement get_irqchip_state method for XIVE to fix shutdown race")
Cc: stable@vger.kernel.org #v5.4+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: seeteena <s1seetee@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211011070203.99726-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 711885906b upstream.
This Kconfig option was added initially so that memory encryption is
enabled by default on machines which support it.
However, devices which have DMA masks that are less than the bit
position of the encryption bit, aka C-bit, require the use of an IOMMU
or the use of SWIOTLB.
If the IOMMU is disabled or in passthrough mode, the kernel would switch
to SWIOTLB bounce-buffering for those transfers.
In order to avoid that,
2cc13bb4f5 ("iommu: Disable passthrough mode when SME is active")
disables the default IOMMU passthrough mode so that devices for which the
default 256K DMA is insufficient, can use the IOMMU instead.
However 2, there are cases where the IOMMU is disabled in the BIOS, etc.
(think the usual hardware folk "oops, I dropped the ball there" cases) or a
driver doesn't properly use the DMA APIs or a device has a firmware or
hardware bug, e.g.:
ea68573d40 ("drm/amdgpu: Fail to load on RAVEN if SME is active")
However 3, in the above GPU use case, there are APIs like Vulkan and
some OpenGL/OpenCL extensions which are under the assumption that
user-allocated memory can be passed in to the kernel driver and both the
GPU and CPU can do coherent and concurrent access to the same memory.
That cannot work with SWIOTLB bounce buffers, of course.
So, in order for those devices to function, drop the "default y" for the
SME by default active option so that users who want to have SME enabled,
will need to either enable it in their config or use "mem_encrypt=on" on
the kernel command line.
[ tlendacky: Generalize commit message. ]
Fixes: 7744ccdbc1 ("x86/mm: Add Secure Memory Encryption (SME) support")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/8bbacd0e-4580-3194-19d2-a0ecad7df09c@molgen.mpg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d388fa01f upstream.
If a cell has 'nbits' equal to a multiple of BITS_PER_BYTE the logic
*p &= GENMASK((cell->nbits%BITS_PER_BYTE) - 1, 0);
will become undefined behavior because nbits modulo BITS_PER_BYTE is 0, and we
subtract one from that making a large number that is then shifted more than the
number of bits that fit into an unsigned long.
UBSAN reports this problem:
UBSAN: shift-out-of-bounds in drivers/nvmem/core.c:1386:8
shift exponent 64 is too large for 64-bit type 'unsigned long'
CPU: 6 PID: 7 Comm: kworker/u16:0 Not tainted 5.15.0-rc3+ #9
Hardware name: Google Lazor (rev3+) with KB Backlight (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x24/0x30
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
ubsan_epilogue+0x10/0x54
__ubsan_handle_shift_out_of_bounds+0x180/0x194
__nvmem_cell_read+0x1ec/0x21c
nvmem_cell_read+0x58/0x94
nvmem_cell_read_variable_common+0x4c/0xb0
nvmem_cell_read_variable_le_u32+0x40/0x100
a6xx_gpu_init+0x170/0x2f4
adreno_bind+0x174/0x284
component_bind_all+0xf0/0x264
msm_drm_bind+0x1d8/0x7a0
try_to_bring_up_master+0x164/0x1ac
__component_add+0xbc/0x13c
component_add+0x20/0x2c
dp_display_probe+0x340/0x384
platform_probe+0xc0/0x100
really_probe+0x110/0x304
__driver_probe_device+0xb8/0x120
driver_probe_device+0x4c/0xfc
__device_attach_driver+0xb0/0x128
bus_for_each_drv+0x90/0xdc
__device_attach+0xc8/0x174
device_initial_probe+0x20/0x2c
bus_probe_device+0x40/0xa4
deferred_probe_work_func+0x7c/0xb8
process_one_work+0x128/0x21c
process_scheduled_works+0x40/0x54
worker_thread+0x1ec/0x2a8
kthread+0x138/0x158
ret_from_fork+0x10/0x20
Fix it by making sure there are any bits to mask out.
Fixes: 69aba7948c ("nvmem: Add a simple NVMEM framework for consumers")
Cc: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211013124511.18726-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b7748ffc upstream.
The number of correctable errors is displayed as uncorrectable
errors because the "SBE" error count is passed to both calls of
edac_mc_handle_error().
Pass the correct uncorrectable error count to the second
edac_mc_handle_error() call when logging uncorrectable errors.
[ bp: Massage commit message. ]
Fixes: 7f6998a412 ("ARM: 8888/1: EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC")
Signed-off-by: Hans Potsch <hans.potsch@nokia.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211006121332.58788-1-hans.potsch@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f9a174f91 upstream.
The virtio specification virtio-v1.1-cs01 states: "Transitional devices
MUST detect Legacy drivers by detecting that VIRTIO_F_VERSION_1 has not
been acknowledged by the driver." This is exactly what QEMU as of 6.1
has done relying solely on VIRTIO_F_VERSION_1 for detecting that.
However, the specification also says: "... the driver MAY read (but MUST
NOT write) the device-specific configuration fields to check that it can
support the device ..." before setting FEATURES_OK.
In that case, any transitional device relying solely on
VIRTIO_F_VERSION_1 for detecting legacy drivers will return data in
legacy format. In particular, this implies that it is in big endian
format for big endian guests. This naturally confuses the driver which
expects little endian in the modern mode.
It is probably a good idea to amend the spec to clarify that
VIRTIO_F_VERSION_1 can only be relied on after the feature negotiation
is complete. Before validate callback existed, config space was only
read after FEATURES_OK. However, we already have two regressions, so
let's address this here as well.
The regressions affect the VIRTIO_NET_F_MTU feature of virtio-net and
the VIRTIO_BLK_F_BLK_SIZE feature of virtio-blk for BE guests when
virtio 1.0 is used on both sides. The latter renders virtio-blk unusable
with DASD backing, because things simply don't work with the default.
See Fixes tags for relevant commits.
For QEMU, we can work around the issue by writing out the feature bits
with VIRTIO_F_VERSION_1 bit set. We (ab)use the finalize_features
config op for this. This isn't enough to address all vhost devices since
these do not get the features until FEATURES_OK, however it looks like
the affected devices actually never handled the endianness for legacy
mode correctly, so at least that's not a regression.
No devices except virtio net and virtio blk seem to be affected.
Long term the right thing to do is to fix the hypervisors.
Cc: <stable@vger.kernel.org> #v4.11
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 82e89ea077 ("virtio-blk: Add validation for block size in config space")
Fixes: fe36cbe067 ("virtio_net: clear MTU when out of range")
Reported-by: markver@us.ibm.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Link: https://lore.kernel.org/r/20211011053921.1198936-1-pasic@linux.ibm.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9a470db27 upstream.
fastrpc driver is using find_vma() without any protection, as a
result we see below warning due to recent patch 5b78ed24e8
("mm/pagemap: add mmap_assert_locked() annotations to find_vma*()")
which added mmap_assert_locked() in find_vma() function.
This bug went un-noticed in previous versions. Fix this issue by adding
required protection while calling find_vma().
CPU: 0 PID: 209746 Comm: benchmark_model Not tainted 5.15.0-rc2-00445-ge14fe2bf817a-dirty #969
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : find_vma+0x64/0xd0
lr : find_vma+0x60/0xd0
sp : ffff8000158ebc40
...
Call trace:
find_vma+0x64/0xd0
fastrpc_internal_invoke+0x570/0xda8
fastrpc_device_ioctl+0x3e0/0x928
__arm64_sys_ioctl+0xac/0xf0
invoke_syscall+0x44/0x100
el0_svc_common.constprop.3+0x70/0xf8
do_el0_svc+0x24/0x88
el0_svc+0x3c/0x138
el0t_64_sync_handler+0x90/0xb8
el0t_64_sync+0x180/0x184
Fixes: 80f3afd72b ("misc: fastrpc: consider address offset before sending to DSP")
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210922154326.8927-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2115b2b16 upstream.
Commit 7c75bde329 ("usb: musb: musb_dsps: request_irq() after
initializing musb") has inverted the calls to
dsps_setup_optional_vbus_irq() and dsps_create_musb_pdev() without
updating correctly the error path. dsps_create_musb_pdev() allocates and
registers a new platform device which must be unregistered and freed
with platform_device_unregister(), and this is missing upon
dsps_setup_optional_vbus_irq() error.
While on the master branch it seems not to trigger any issue, I observed
a kernel crash because of a NULL pointer dereference with a v5.10.70
stable kernel where the patch mentioned above was backported. With this
kernel version, -EPROBE_DEFER is returned the first time
dsps_setup_optional_vbus_irq() is called which triggers the probe to
error out without unregistering the platform device. Unfortunately, on
the Beagle Bone Black Wireless, the platform device still living in the
system is being used by the USB Ethernet gadget driver, which during the
boot phase triggers the crash.
My limited knowledge of the musb world prevents me to revert this commit
which was sent to silence a robot warning which, as far as I understand,
does not make sense. The goal of this patch was to prevent an IRQ to
fire before the platform device being registered. I think this cannot
ever happen due to the fact that enabling the interrupts is done by the
->enable() callback of the platform musb device, and this platform
device must be already registered in order for the core or any other
user to use this callback.
Hence, I decided to fix the error path, which might prevent future
errors on mainline kernels while also fixing older ones.
Fixes: 7c75bde329 ("usb: musb: musb_dsps: request_irq() after initializing musb")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211005221631.1529448-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38fa3206bf upstream.
While reboot the system by sysrq, the following bug will be occur.
BUG: sleeping function called from invalid context at kernel/locking/semaphore.c:90
in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 10052, name: rc.shutdown
CPU: 3 PID: 10052 Comm: rc.shutdown Tainted: G W O 5.10.0 #1
Call trace:
dump_backtrace+0x0/0x1c8
show_stack+0x18/0x28
dump_stack+0xd0/0x110
___might_sleep+0x14c/0x160
__might_sleep+0x74/0x88
down_interruptible+0x40/0x118
virt_efi_reset_system+0x3c/0xd0
efi_reboot+0xd4/0x11c
machine_restart+0x60/0x9c
emergency_restart+0x1c/0x2c
sysrq_handle_reboot+0x1c/0x2c
__handle_sysrq+0xd0/0x194
write_sysrq_trigger+0xbc/0xe4
proc_reg_write+0xd4/0xf0
vfs_write+0xa8/0x148
ksys_write+0x6c/0xd8
__arm64_sys_write+0x18/0x28
el0_svc_common.constprop.3+0xe4/0x16c
do_el0_svc+0x1c/0x2c
el0_svc+0x20/0x30
el0_sync_handler+0x80/0x17c
el0_sync+0x158/0x180
The reason for this problem is that irq has been disabled in
machine_restart() and then it calls down_interruptible() in
virt_efi_reset_system(), which would occur sleep in irq context,
it is dangerous! Commit 99409b935c9a("locking/semaphore: Add
might_sleep() to down_*() family") add might_sleep() in
down_interruptible(), so the bug info is here. down_trylock()
can solve this problem, cause there is no might_sleep.
--------
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhang Jianhua <chris.zjh@huawei.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3a72ca803 upstream.
Joe reports that using a statically allocated buffer for converting CPER
error records into human readable text is probably a bad idea. Even
though we are not aware of any actual issues, a stack buffer is clearly
a better choice here anyway, so let's move the buffer into the stack
frames of the two functions that refer to it.
Cc: <stable@vger.kernel.org>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42641042c1 upstream.
clang-14 complains about an unusual way of converting a pointer to
an integer:
drivers/misc/cb710/sgbuf2.c:50:15: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
return ((ptr - NULL) & 3) != 0;
Replace this with a normal cast to uintptr_t.
Fixes: 5f5bac8272 ("mmc: Driver for CB710/720 memory card reader (MMC part)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927121408.939246-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0e50d356 upstream.
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4afb912f43 upstream.
Error injection testing uncovered a case where we'd end up with a
corrupt file system with a missing extent in the middle of a file. This
occurs because the if statement to decide if we should abort is wrong.
The only way we would abort in this case is if we got a ret !=
-EOPNOTSUPP and we called from the file clone code. However the
prealloc code uses this path too. Instead we need to abort if there is
an error, and the only error we _don't_ abort on is -EOPNOTSUPP and only
if we came from the clone file code.
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d175209be0 upstream.
I hit a stuck relocation on btrfs/061 during my overnight testing. This
turned out to be because we had left over extent entries in our extent
root for a data reloc inode that no longer existed. This happened
because in btrfs_drop_extents() we only update refs if we have SHAREABLE
set or we are the tree_root. This regression was introduced by
aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
where we stopped setting SHAREABLE for the data reloc tree.
The problem here is we actually do want to update extent references for
data extents in the data reloc tree, in fact we only don't want to
update extent references if the file extents are in the log tree.
Update this check to only skip updating references in the case of the
log tree.
This is relatively rare, because you have to be running scrub at the
same time, which is what btrfs/061 does. The data reloc inode has its
extents pre-allocated, and then we copy the extent into the
pre-allocated chunks. We theoretically should never be calling
btrfs_drop_extents() on a data reloc inode. The exception of course is
with scrub, if our pre-allocated extent falls inside of the block group
we are scrubbing, then the block group will be marked read only and we
will be forced to cow that extent. This means we will call
btrfs_drop_extents() on that range when we COW that file extent.
This isn't really problematic if we do this, the data reloc inode
requires that our extent lengths match exactly with the extent we are
copying, thankfully we validate the extent is correct with
get_new_location(), so if we happen to COW only part of the extent we
won't link it in when we do the relocation, so we are safe from any
other shenanigans that arise because of this interaction with scrub.
Fixes: aeb935a455 ("btrfs: don't set SHAREABLE flag for data reloc tree")
CC: stable@vger.kernel.org # 5.8+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfd312695b upstream.
At replay_one_name(), we are treating any error from btrfs_lookup_inode()
as if the inode does not exists. Fix this by checking for an error and
returning it to the caller.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52db77791f upstream.
At __inode_add_ref(), we treating any error returned from
btrfs_lookup_dir_item() or from btrfs_lookup_dir_index_item() as meaning
that there is no existing directory entry in the fs/subvolume tree.
This is not correct since we can get errors such as, for example, -EIO
when reading extent buffers while searching the fs/subvolume's btree.
So fix that and return the error to the caller when it is not -ENOENT.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e15ac64137 upstream.
At replay_one_one(), we are treating any error returned from
btrfs_lookup_dir_item() or from btrfs_lookup_dir_index_item() as meaning
that there is no existing directory entry in the fs/subvolume tree.
This is not correct since we can get errors such as, for example, -EIO
when reading extent buffers while searching the fs/subvolume's btree.
So fix that and return the error to the caller when it is not -ENOENT.
CC: stable@vger.kernel.org # 4.14+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 171316a68d upstream.
The return type of ktime_divns() is s64. The timeout_to_jiffies() currently
assigns the result of this ktime_divns() to unsigned long, which on 32 bit
systems may overflow. Furthermore, the result of this function is sometimes
also passed to functions which expect signed long, dma_fence_wait_timeout()
is one such example.
Fix this by adjusting the type of remaining_jiffies to s64, so we do not
suffer overflow there, and return a value limited to range of 0..INT_MAX,
which is safe for all usecases of this timeout.
The above overflow can be triggered if userspace passes in too large timeout
value, larger than INT_MAX / HZ seconds. The kernel detects it and complains
about "schedule_timeout: wrong timeout value %lx" and generates a warning
backtrace.
Note that this fixes commit 6cedb8b377 ("drm/msm: avoid using 'timespec'"),
because the previously used timespec_to_jiffies() function returned unsigned
long instead of s64:
static inline unsigned long timespec_to_jiffies(const struct timespec *value)
Fixes: 6cedb8b377 ("drm/msm: avoid using 'timespec'")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: stable@vger.kernel.org # 5.6+
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210917005913.157379-1-marex@denx.de
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e5809a4dd upstream.
For non-4K PAGE_SIZE configs, the largest gigantic huge page size is
CONT_PMD_SHIFT order. On arm64 with 64K PAGE_SIZE, the gigantic page is
16G. Therefore, one should be able to specify 'hugetlb_cma=16G' on the
kernel command line so that one gigantic page can be allocated from CMA.
However, when adding such an option the following message is produced:
hugetlb_cma: cma area should be at least 8796093022208 MiB
This is because the calculation for non-4K gigantic page order is
incorrect in the arm64 specific routine arm64_hugetlb_cma_reserve().
Fixes: abb7962adc ("arm64/hugetlb: Reserve CMA areas for gigantic pages on 16K and 64K configs")
Cc: <stable@vger.kernel.org> # 5.9.x
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20211005202529.213812-1-mike.kravetz@oracle.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af89ebaa64 upstream.
gpr_get() return the entire pt_regs (include sr) to userspace, if we
don't restore the C bit in gpr_set, it may break the ALU result in
that context. So the C flag bit is part of gpr context, that's why
riscv totally remove the C bit in the ISA. That makes sr reg clear
from userspace to supervisor privilege.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbd63c08cd upstream.
csky restore_sigcontext() blindly overwrites regs->sr with the value
it finds in sigcontext. Attacker can store whatever they want in there,
which includes things like S-bit. Userland shouldn't be able to set
that, or anything other than C flag (bit 0).
Do the same thing other architectures with protected bits in flags
register do - preserve everything that shouldn't be settable in
user mode, picking the rest from the value saved is sigcontext.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
