[ Upstream commit d5349775c1 ]
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54d390086 ]
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26d5bb9e4c ]
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e5383d790 ]
Older (and maybe current) versions of systemd set release_agent to "" when
shutting down, but do not set notify_on_release to 0.
Since 64e90a8acb ("Introduce STATIC_USERMODEHELPER to mediate
call_usermodehelper()"), we filter out such calls when the user mode helper
path is "". However, when used in conjunction with an actual (i.e. non "")
STATIC_USERMODEHELPER, the path is never "", so the real usermode helper
will be called with argv[0] == "".
Let's avoid this by not invoking the release_agent when it is "".
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 209c65b61d ]
When registers a phy_device successful, should terminate the loop
or the phy_device would be registered in other addr. If there are
multiple PHYs without reg properties, it will go wrong.
Signed-off-by: Dajun Jin <adajunjin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2de7fb60a4 ]
Building cpupower with -fno-common in CFLAGS results in errors due to
multiple definitions of the 'cpu_count' and 'start_time' variables.
./utils/idle_monitor/snb_idle.o:./utils/idle_monitor/cpupower-monitor.h:28:
multiple definition of `cpu_count';
./utils/idle_monitor/nhm_idle.o:./utils/idle_monitor/cpupower-monitor.h:28:
first defined here
...
./utils/idle_monitor/cpuidle_sysfs.o:./utils/idle_monitor/cpuidle_sysfs.c:22:
multiple definition of `start_time';
./utils/idle_monitor/amd_fam14h_idle.o:./utils/idle_monitor/amd_fam14h_idle.c:85:
first defined here
The -fno-common option will be enabled by default in GCC 10.
Bug: https://bugs.gentoo.org/707462
Signed-off-by: Mike Gilbert <floppym@gentoo.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dee1bc0d ]
An NFS client that mounts multiple exports from the same NFS
server with higher NFSv4 versions disabled (i.e. 4.2) and without
forcing a specific NFS version results in fscache index cookie
collisions and the following messages:
[ 570.004348] FS-Cache: Duplicate cookie detected
Each nfs_client structure should have its own fscache index cookie,
so add the minorversion to nfs_server_key.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200145
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db8dd96972 ]
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
# mount | grep cgroup
# dd if=/mnt/cgroup.procs bs=1 # normal output
...
1294
1295
1296
1304
1382
584+0 records in
584+0 records out
584 bytes copied
dd: /mnt/cgroup.procs: cannot skip to specified offset
83 <<< generates end of last line
1383 <<< ... and whole last line once again
0+1 records in
0+1 records out
8 bytes copied
dd: /mnt/cgroup.procs: cannot skip to specified offset
1386 <<< generates last line anyway
0+1 records in
0+1 records out
5 bytes copied
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 187a9830c9 ]
For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e239c6d686 ]
In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39369fd536 ]
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1de0306c3a ]
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 09e91dbea0 ]
The hsr module has been supporting the list and status command.
(HSR_C_GET_NODE_LIST and HSR_C_GET_NODE_STATUS)
These commands send node information to the user-space via generic netlink.
But, in the non-init_net namespace, these commands are not allowed
because .netnsok flag is false.
So, there is no way to get node information in the non-init_net namespace.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca19c70f52 ]
The hsr_get_node_list() is to send node addresses to the userspace.
If there are so many nodes, it could fail because of buffer size.
In order to avoid this failure, the restart routine is added.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 173756b868 ]
hsr_get_node_{list/status}() are not under rtnl_lock() because
they are callback functions of generic netlink.
But they use __dev_get_by_index() without rtnl_lock().
So, it would use unsafe data.
In order to fix it, rcu_read_lock() and dev_get_by_index_rcu()
are used instead of __dev_get_by_index().
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1f8f78ffe ]
ERSPAN shares most of the code path with GRE and gretap code. While that
helps keep the code compact, it is also error prone. Currently a broken
userspace can turn a gretap tunnel into a de facto ERSPAN one by passing
IFLA_GRE_ERSPAN_VER. There has been a similar issue in ip6gretap in the
past.
To prevent these problems in future, split the newlink and changelink code
paths. Split the ERSPAN code out of ipgre_netlink_parms() into a new
function erspan_netlink_parms(). Extract a piece of common logic from
ipgre_newlink() and ipgre_changelink() into ipgre_newlink_encap_setup().
Add erspan_newlink() and erspan_changelink().
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d765a5e4b ]
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62bfb932a5 ]
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b5b561cea ]
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 62d4073e86 ]
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a24ec3220f ]
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed7903 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 384d91c267 ]
gro_cells_init() returns error if memory allocation is failed.
But the vxlan module doesn't check the return value of gro_cells_init().
Fixes: 58ce31cca1 ("vxlan: GRO support at tunnel layer")`
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cd6cbf593 ]
When application uses TCP_QUEUE_SEQ socket option to
change tp->rcv_next, we must also update tp->copied_seq.
Otherwise, stuff relying on tcp_inq() being precise can
eventually be confused.
For example, tcp_zerocopy_receive() might crash because
it does not expect tcp_recv_skb() to return NULL.
We could add tests in various places to fix the issue,
or simply make sure tcp_inq() wont return a random value,
and leave fast path as it is.
Note that this fixes ioctl(fd, SIOCINQ, &val) at the same
time.
Fixes: ee9952831c ("tcp: Initial repair mode")
Fixes: 05255b823a ("tcp: add TCP_ZEROCOPY_RECEIVE support for zerocopy receive")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b738a185be ]
skb->rbnode is sharing three skb fields : next, prev, dev
When a packet is sent, TCP keeps the original skb (master)
in a rtx queue, which was converted to rbtree a while back.
__tcp_transmit_skb() is responsible to clone the master skb,
and add the TCP header to the clone before sending it
to network layer.
skb_clone() already clears skb->next and skb->prev, but copies
the master oskb->dev into the clone.
We need to clear skb->dev, otherwise lower layers could interpret
the value as a pointer to a netdev.
This old bug surfaced recently when commit 28f8bfd1ac
("netfilter: Support iif matches in POSTROUTING") was merged.
Before this netfilter commit, skb->dev value was ignored and
changed before reaching dev_queue_xmit()
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Fixes: 28f8bfd1ac ("netfilter: Support iif matches in POSTROUTING")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Martin Zaharinov <micron10@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07f8e4d0fd ]
In rare cases retransmit logic will make a full skb copy, which will not
trigger the zeroing added in recent change
b738a185be ("tcp: ensure skb->dev is NULL before leaving TCP stack").
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Fixes: 28f8bfd1ac ("netfilter: Support iif matches in POSTROUTING")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2091a3d42b ]
As the description before netdev_run_todo, we cannot call free_netdev
before rtnl_unlock, fix it by reorder the code.
This patch is a 1:1 copy of upstream slip.c commit f596c87005
("slip: not call free_netdev before rtnl_unlock in slip_open").
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f13bc68131 ]
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0dcdf9f640 ]
The nci_conn_max_data_pkt_payload_size() function sometimes returns
-EPROTO so "max_size" needs to be signed for the error handling to
work. We can make "payload_size" an int as well.
Fixes: a06347c04c ("NFC: Add Intel Fields Peak NFC solution driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9de9aa487d ]
Make sure we clean up devicetree related configuration
also when clock init fails.
Fixes: fecd4d7eef ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b1be2e8cd2 ]
syzbot reported a use-after-free in tcindex_dump(). This is due to
the lack of RTNL in the deferred rcu work. We queue this work with
RTNL in tcindex_change(), later, tcindex_dump() is called:
fh = tp->ops->get(tp, t->tcm_handle);
...
err = tp->ops->change(..., &fh, ...);
tfilter_notify(..., fh, ...);
but there is nothing to serialize the pending
tcindex_partial_destroy_work() with tcindex_dump().
Fix this by simply holding RTNL in tcindex_partial_destroy_work(),
so that it won't be called until RTNL is released after
tc_new_tfilter() is completed.
Reported-and-tested-by: syzbot+653090db2562495901dc@syzkaller.appspotmail.com
Fixes: 3d210534cc ("net_sched: fix a race condition in tcindex_destroy()")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd2af10402 ]
Currently, on replace, the previous action instance params
is swapped with a newly allocated params. The old params is
only freed (via kfree_rcu), without releasing the allocated
ct zone template related to it.
Call tcf_ct_params_free (via call_rcu) for the old params,
so it will release it.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c312c7818b ]
The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.
Fix this by using devm_clk_get_optional() to handle this clock properly.
Fixes: b78ac6ecd1 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 749f6f6843 ]
When the DP83867 PHY is strapped to enable Fast Link Drop (FLD) feature
STRAP_STS2.STRAP_ FLD (reg 0x006F bit 10), the Energy Lost Threshold for
FLD Energy Lost Mode FLD_THR_CFG.ENERGY_LOST_FLD_THR (reg 0x002e bits 2:0)
will be defaulted to 0x2. This may cause the phy link to be unstable. The
new DP83867 DM recommends to always restore ENERGY_LOST_FLD_THR to 0x1.
Hence, restore default value of FLD_THR_CFG.ENERGY_LOST_FLD_THR to 0x1 when
FLD is enabled by bootstrapping as recommended by DM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61fad6816f ]
PACKET_RX_RING can cause multiple writers to access the same slot if a
fast writer wraps the ring while a slow writer is still copying. This
is particularly likely with few, large, slots (e.g., GSO packets).
Synchronize kernel thread ownership of rx ring slots with a bitmap.
Writers acquire a slot race-free by testing tp_status TP_STATUS_KERNEL
while holding the sk receive queue lock. They release this lock before
copying and set tp_status to TP_STATUS_USER to release to userspace
when done. During copying, another writer may take the lock, also see
TP_STATUS_KERNEL, and start writing to the same slot.
Introduce a new rx_owner_map bitmap with a bit per slot. To acquire a
slot, test and set with the lock held. To release race-free, update
tp_status and owner bit as a transaction, so take the lock again.
This is the one of a variety of discussed options (see Link below):
* instead of a shadow ring, embed the data in the slot itself, such as
in tp_padding. But any test for this field may match a value left by
userspace, causing deadlock.
* avoid the lock on release. This leaves a small race if releasing the
shadow slot before setting TP_STATUS_USER. The below reproducer showed
that this race is not academic. If releasing the slot after tp_status,
the race is more subtle. See the first link for details.
* add a new tp_status TP_KERNEL_OWNED to avoid the transactional store
of two fields. But, legacy applications may interpret all non-zero
tp_status as owned by the user. As libpcap does. So this is possible
only opt-in by newer processes. It can be added as an optional mode.
* embed the struct at the tail of pg_vec to avoid extra allocation.
The implementation proved no less complex than a separate field.
The additional locking cost on release adds contention, no different
than scaling on multicore or multiqueue h/w. In practice, below
reproducer nor small packet tcpdump showed a noticeable change in
perf report in cycles spent in spinlock. Where contention is
problematic, packet sockets support mitigation through PACKET_FANOUT.
And we can consider adding opt-in state TP_KERNEL_OWNED.
Easy to reproduce by running multiple netperf or similar TCP_STREAM
flows concurrently with `tcpdump -B 129 -n greater 60000`.
Based on an earlier patchset by Jon Rosen. See links below.
I believe this issue goes back to the introduction of tpacket_rcv,
which predates git history.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg237222.html
Suggested-by: Jon Rosen <jrosen@cisco.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jon Rosen <jrosen@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 065fd83e1b ]
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 428c491332 ]
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
00:05.0 Ethernet controller [0200]: Amazon.com, Inc. Elastic Network
Adapter (ENA) [1d0f:ec20]
Suggested-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e80f40cbe4 ]
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638 ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22259471b5 ]
Andrew reported:
After a number of network port link up/down changes, sometimes the switch
port gets stuck in a state where it thinks it is still transmitting packets
but the cpu port is not actually transmitting anymore. In this state you
will see a message on the console
"mtk_soc_eth 1e100000.ethernet eth0: transmit timed out" and the Tx counter
in ifconfig will be incrementing on virtual port, but not incrementing on
cpu port.
The issue is that MAC TX/RX status has no impact on the link status or
queue manager of the switch. So the queue manager just queues up packets
of a disabled port and sends out pause frames when the queue is full.
Change the LINK bit to reflect the link status.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reported-by: Andrew Smith <andrew.smith@digi.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e62f543be ]
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b8 ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 961d0e5b32 ]
Currently the software CBS does not consider the packet sending time
when depleting the credits. It caused the throughput to be
Idleslope[kbps] * (Port transmit rate[kbps] / |Sendslope[kbps]|) where
Idleslope * (Port transmit rate / (Idleslope + |Sendslope|)) = Idleslope
is expected. In order to fix the issue above, this patch takes the time
when the packet sending completes into account by moving the anchor time
variable "last" ahead to the send completion time upon transmission and
adding wait when the next dequeue request comes before the send
completion time of the previous packet.
changelog:
V2->V3:
- remove unnecessary whitespace cleanup
- add the checks if port_rate is 0 before division
V1->V2:
- combine variable "send_completed" into "last"
- add the comment for estimate of the packet sending
Fixes: 585d763af0 ("net/sched: Introduce Credit Based Shaper (CBS) qdisc")
Signed-off-by: Zh-yuan Ye <ye.zh-yuan@socionext.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13d0f7b814 ]
The bpfilter UMH code was recently changed to log its informative messages to
/dev/kmsg, however this interface doesn't support SEEK_CUR yet, used by
dprintf(). As result dprintf() returns -EINVAL and doesn't log anything.
However there already had some discussions about supporting SEEK_CUR into
/dev/kmsg interface in the past it wasn't concluded. Since the only user of
that from userspace perspective inside the kernel is the bpfilter UMH
(userspace) module it's better to correct it here instead waiting a conclusion
on the interface.
Fixes: 36c4357c63 ("net: bpfilter: print umh messages to /dev/kmsg")
Signed-off-by: Bruno Meneguele <bmeneg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6bf1bafdc ]
list_for_each_entry_from_reverse() iterates backwards over the list from
the current position, but in the error path we should start from the
previous position.
Fix this by using list_for_each_entry_continue_reverse() instead.
This suppresses the following error from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//spectrum_mr.c:655:34-38: ERROR:
invalid reference to the index variable of the iterator on line 636
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6002059d78 ]
During initialization the driver issues a software reset command and
then waits for the system status to change back to "ready" state.
However, before issuing the reset command the driver does not check that
the system is actually in "ready" state. On Spectrum-{1,2} systems this
was always the case as the hardware initialization time is very short.
On Spectrum-3 systems this is no longer the case. This results in the
software reset command timing-out and the driver failing to load:
[ 6.347591] mlxsw_spectrum3 0000:06:00.0: Cmd exec timed-out (opcode=40(ACCESS_REG),opcode_mod=0,in_mod=0)
[ 6.358382] mlxsw_spectrum3 0000:06:00.0: Reg cmd access failed (reg_id=9023(mrsr),type=write)
[ 6.368028] mlxsw_spectrum3 0000:06:00.0: cannot register bus device
[ 6.375274] mlxsw_spectrum3: probe of 0000:06:00.0 failed with error -110
Fix this by waiting for the system to become ready both before issuing
the reset command and afterwards. In case of failure, print the last
system status to aid in debugging.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
