This allows enabling support for extra hardware with just a module
param, without kernel/module recompilation.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently HW doesn't require us to generate MMIC
for TKIP suite.
Each frame was 8 bytes longer than it should be
and some APs would drop frames that exceed 1520
bytes of 802.11 payload. This could be observed
during throughput tests or fragmented IP traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nonsense channel flags were being set.
Although it doesn't seem this was visible to the
user the patch makes sure that channel
availability won't be crippled in the future if
ath_common behaviour changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code writes the default_power2 value into the TX field
of the RFCSR50 register, however the condition in the if
statement uses default_power1. Due to this, wrong TX power
value might be written into the register.
Use the correct value in the condition to fix the issue.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org # 3.10
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 3T/3R devices are using the tertiary PAs/LNAs
however those are never turned on. Fix the code to
turn on those on for such devices.
Also modify the code to use switch statements to
improve readability.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The secondary PAs/LNAs are turned on only for 2T/2R
devices, however these are used for 3T/3R devices as
well. Always turn those on if the device uses more
than one tx/rx chains.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink 3T chipsets are using a different EEPROM
layout than the others. The EEPROM on these devices
contain more data than the others which does not fit
into 272 byte which the rt2800 driver actually uses.
The Ralink reference driver defines EEPROM_SIZE to
512/1024 bytes for PCI/USB devices respectively.
Increase the EEPROM_SIZE constant to 512 bytes, in
order to make room for EEPROM data of 3T devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver displays wrong alarms for temperature attributes.
Turns out that temperature alarm bits are not fixed, but determined
by temperature source mapping. To fix the problem, walk through
the temperature sources to determine the correct alarm bit associated
with a given attribute.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another way that is device tree to pass the shunt resistor
value to driver except for platform data.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[Guenter Roeck: Added missing of.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace some written information with tables to improve readability
and to simplify adding newer devices in the future.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These changes add DS1731 chip support to the ds1621 driver,
Kconfig, and documentation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This helps the kernel to find the right module once the device is
created.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM84 does not support minimum temperature registers.
Only create the respective sysfs attributes for other chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Due to a lack of device and vendor identification registers, the
Dallas/Maxim DS16xx devices cannot be uniquely detected, sometimes
resulting in false positives. Therefore, the detect function is
being removed in favor of explicit device instantiation.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add definitions, information, and code for ds1631 chip support
to the ds1621 driver.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ds1721 device can be configured for 9..12 bit resolutions;
add a sysfs attribute for userspace to configure this attribute.
The definition, description, details, and usage are shown in the
documentation and were crafted from an LM73 driver patch done by
Chris Verges & Guenter Roeck).
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the ds1621 documentation, driver, and Kconfig with
ds1721 chip support.
Signed-off-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a GFS2 file system is mounted with quotas and a file is grown
in such a way that its free blocks for the allocation are represented
in a secondary bitmap, GFS2 ran out of blocks in the transaction.
That resulted in "fatal: assertion "tr->tr_num_buf <= tr->tr_blocks".
This patch reserves extra blocks for the quota change so the
transaction has enough space.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Add platform specific functionality for the DW SD/MMC driver for
SoCFPGA. Move SDMMC_CMD_USE_HOLD_REG to dw_mmc.h so other platforms
can use this define.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com
Signed-off-by: Chris Ball <cjb@laptop.org>
Although the HC supports HS200 (eMMC) the caps2 are always zero; this
means there's no way to use the super speed mode (when init the card).
If the HC support SDR104, for SD3.0, so it also supports HS200 for eMMC
and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.
Reported-by: Youssef Triki <youssef.triki@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit bb691ae464 breaks boot on OLPC
XO-4, it hangs somewhere inside sdhci_add_host.
When pm_runtime_set_autosuspend_delay() was being called, the device's
usage counter was 0, causing the PM layer to runtime-suspend the
device. We then went on to call sdhci_add_host() on a suspended
device, which hung.
Fix this by making the driver consistent with the omap_hsmmc driver,
both in terms of runtime PM initialization and error handling. Now
the device is not runtime-suspended until we exit the probe routine.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DT-binding for MMC_CAP2_FULL_PWR_CYCLE, is used to indicate whether
it is possible to perform a full power cycle of the card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP2_FULL_PWR_CYCLE shall be set by host drivers which are able to
do a complete power cycle of the card. In the eMMC case that includes
both vcc and vccq.
This CAP is providing the protocol layer with important information,
needed to take optimized decisions during card initialization and in
the suspend/resume sequence.
MMC_CAP2_POWEROFF_NOTIFY is replaced by MMC_CAP2_FULL_PWR_CYCLE, since
it makes sense to use a wider scope for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In suspend mode it is important to save power. If the host is able to
cut buth vcc and vccq, the MMC_CAP2_POWEROFF_NOTIFY shall be set. It
will mean the card will be completely powered down at suspend and the
power off notification cmd will be sent prior power down.
It seems common not being able to cut both vcc and vccq for a host. In
this situation we issue the sleep cmd in favor of the power off
notification cmd, to save more power.
While maintainng the above policy, we also want to make use of the
power off notification in the shutdown sequence, even in the case were
the host has not set MMC_CAP2_POWEROFF_NOTIFY, since we know vcc and
vccq will regardless be cut.
We accomplish this by always enabling the power off notification byte
in the EXT_CSD and issue the power off notification when either
MMC_CAP2_POWEROFF_NOTIFY is set or we are executing a shutdown.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The shutdown sequence of an (e)MMC is very similar to a suspend. We
re-use the suspend function and tell it we are not in suspend context.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Depending on the context of the operation while powering down the card,
either POWER_OFF_NOTIFY_SHORT or POWER_OFF_NOTIFY_LONG will be used. In
suspend context a short timeout is preferred while a long timeout would
be acceptable in a shutdown/hibernation context.
We add a new parameter to the mmc_suspend function so we can provide an
indication of what notification type to use.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For the SD .shutdown callback we re-use the SD suspend function since
it performs the relevant actions.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding an optional .shutdown callback to the bus_ops struct we
provide the possibility to let each bus type handle it's shutdown
requirements.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host should be responsible to suspend|resume the host and not the
card. This patch changes this behaviour, by moving the responsiblity
to the mmc bus instead which already holds the card device.
The exported functions mmc_suspend|resume_host are now to be considered
as depcrecated. Once all host drivers moves away from using them, we
can remove them. As of now, a successful error code is always returned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.
Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch moves the validation for all the suspend prerequisites to be
done at SUSPEND_PREPARE notification. Previously in the SDIO case parts
of the validation was done from mmc_suspend_host.
This patch invents a new pre_suspend bus_ops callback and implements it
for SDIO. Returning an error code from it, will mean at SUSPEND_PREPARE
notification, the card will be removed before proceeding with the
suspend sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For every bus_ops type the .remove callback always exist, thus there
are no need to check the existence of it, before we decide to call it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use managed resources for the mmio memory region and the clock.
Makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the slot-gpio helpers to handle the write protect and card detect
GPIO pins instead of re-implementing the same functionality in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's a bit shorter than open-conding it. While we are at it also make
jz4740_mmc_pm_ops static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For no reason, the code handling write errors was implemented while
the code handling read errors was missing.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The following error randomly appears on an imx6q board where gpio is
used to implement card-detection when mounting EXT4 rootfs during boot.
mmc1: Card removed during transfer!
mmc1: Resetting controller.
mmcblk0: unknown error -123 sending read/write command, card status 0x900
end_request: I/O error, dev mmcblk0, sector 106744
EXT4-fs error (device mmcblk0p2): ext4_find_entry:1312: inode #5011: comm swapper/0: reading directory lblock 0
It turns out that the error message comes from the card removal check
in function sdhci_card_event(). While we have a well implemented
function sdhci_do_get_cd() handling all the possible cases of
CD, the current code only checks controller internal CD case. That
causes problem for other CD cases like gpio on above imx6q board.
Improve the check by using sdhci_do_get_cd() to cover all possible CD
cases, so that above error on the imx6q board gets fixed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As of now we rely on code outside of the driver to set the ciu clock
frequency. There's no reason to do that. Add support for setting up
the clock in the driver during probe.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It is possible to specify a regulator that should be turned on when
dw_mmc is probed. At the moment dw_mmc will fail to use the regulator
properly if the regulator probes after dw_mmc. Fix this problem by
honoring EPROBE_DEFER.
At the same time move the regulator code out of the slot init code.
We only specify one regulator for the whole device and other parts of
the code (like suspend/resume) assume that the regulator has only been
enabled once.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In order to make it possible to reduce the SD bus frequency,
parse the optional "max-frequency" attribute as documented in
devicetree/bindings/mmc/mmc.txt
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDCLK is divided down from the host controller clock. Host
controller clock may be different from the maximum SDCLK, so
get it from the platform, instead of just using the max SDCLK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Inside the routine mmc_blk_ioctl_cmd() the sanitize command is
identified according to the value of bits 16-23 of the argument.
but what happens if a different command is sent, and only by
chance, bits 16-23 contain the value of SANITIZE command ?
In that case a SANITIZE command will be falsely identified.
In order to prevent such a case, the condition is expanded and
now it also checks the opcode itself, and verifies that it is an
MMC_SWITCH opcode.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
