[ Upstream commit 3ba7f53f8b ]
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50ac747984 ]
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d09c548dbf ]
When mirror/redirect a skb to a different port, the ct info should be reset
for reclassification. Or the pkts will match unexpected rules. For example,
with following topology and commands:
-----------
|
veth0 -+-------
|
veth1 -+-------
|
------------
tc qdisc add dev veth0 clsact
# The same with "action mirred egress mirror dev veth1" or "action mirred ingress redirect dev veth1"
tc filter add dev veth0 egress chain 1 protocol ip flower ct_state +trk action mirred ingress mirror dev veth1
tc filter add dev veth0 egress chain 0 protocol ip flower ct_state -inv action ct commit action goto chain 1
tc qdisc add dev veth1 clsact
tc filter add dev veth1 ingress chain 0 protocol ip flower ct_state +trk action drop
ping <remove ip via veth0> &
tc -s filter show dev veth1 ingress
With command 'tc -s filter show', we can find the pkts were dropped on
veth1.
Fixes: b57dc7c13e ("net/sched: Introduce action ct")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f3d65c166 ]
There can be a race between the waiters for a tx work request buffer
and the link down processing that finally clears the link. Although
all waiters are woken up before the link is cleared there might be
waiters which did not yet get back control and are still waiting.
This results in an access to a cleared wait queue head.
Fix this by introducing atomic reference counting around the wait calls,
and wait with the link clear processing until all waiters have finished.
Move the work request layer related calls into smc_wr.c and set the
link state to INACTIVE before calling smcr_link_clear() in
smc_llc_srv_add_link().
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2459dcb96b ]
IFLA_IFNAME is nul-term string which means that IFLA_IFNAME buffer can be
larger than length of string which contains.
Function __rtnl_newlink() generates new own ifname if either IFLA_IFNAME
was not specified at all or userspace passed empty nul-term string.
It is expected that if userspace does not specify ifname for new ppp netdev
then kernel generates one in format "ppp<id>" where id matches to the ppp
unit id which can be later obtained by PPPIOCGUNIT ioctl.
And it works in this way if IFLA_IFNAME is not specified at all. But it
does not work when IFLA_IFNAME is specified with empty string.
So fix this logic also for empty IFLA_IFNAME in ppp_nl_newlink() function
and correctly generates ifname based on ppp unit identifier if userspace
did not provided preferred ifname.
Without this patch when IFLA_IFNAME was specified with empty string then
kernel created a new ppp interface in format "ppp<id>" but id did not
match ppp unit id returned by PPPIOCGUNIT ioctl. In this case id was some
number generated by __rtnl_newlink() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: bb8082f691 ("ppp: build ifname using unit identifier for rtnl based devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2383cb9497 ]
Commit a5e63c7d38 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38 ("net: phy: micrel: Fix detection of ksz87xx switch")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4eb1f4032 ]
In __htab_map_lookup_and_delete_batch(), hash buckets are iterated
over to count the number of elements in each bucket (bucket_size).
If bucket_size is large enough, the multiplication to calculate
kvmalloc() size could overflow, resulting in out-of-bounds write
as reported by KASAN:
[...]
[ 104.986052] BUG: KASAN: vmalloc-out-of-bounds in __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.986489] Write of size 4194224 at addr ffffc9010503be70 by task crash/112
[ 104.986889]
[ 104.987193] CPU: 0 PID: 112 Comm: crash Not tainted 5.14.0-rc4 #13
[ 104.987552] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
[ 104.988104] Call Trace:
[ 104.988410] dump_stack_lvl+0x34/0x44
[ 104.988706] print_address_description.constprop.0+0x21/0x140
[ 104.988991] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.989327] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.989622] kasan_report.cold+0x7f/0x11b
[ 104.989881] ? __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.990239] kasan_check_range+0x17c/0x1e0
[ 104.990467] memcpy+0x39/0x60
[ 104.990670] __htab_map_lookup_and_delete_batch+0x5ce/0xb60
[ 104.990982] ? __wake_up_common+0x4d/0x230
[ 104.991256] ? htab_of_map_free+0x130/0x130
[ 104.991541] bpf_map_do_batch+0x1fb/0x220
[...]
In hashtable, if the elements' keys have the same jhash() value, the
elements will be put into the same bucket. By putting a lot of elements
into a single bucket, the value of bucket_size can be increased to
trigger the integer overflow.
Triggering the overflow is possible for both callers with CAP_SYS_ADMIN
and callers without CAP_SYS_ADMIN.
It will be trivial for a caller with CAP_SYS_ADMIN to intentionally
reach this overflow by enabling BPF_F_ZERO_SEED. As this flag will set
the random seed passed to jhash() to 0, it will be easy for the caller
to prepare keys which will be hashed into the same value, and thus put
all the elements into the same bucket.
If the caller does not have CAP_SYS_ADMIN, BPF_F_ZERO_SEED cannot be
used. However, it will be still technically possible to trigger the
overflow, by guessing the random seed value passed to jhash() (32bit)
and repeating the attempt to trigger the overflow. In this case,
the probability to trigger the overflow will be low and will take
a very long time.
Fix the integer overflow by calling kvmalloc_array() instead of
kvmalloc() to allocate memory.
Fixes: 057996380a ("bpf: Add batch ops to all htab bpf map")
Signed-off-by: Tatsuhiko Yasumatsu <th.yasumatsu@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210806150419.109658-1-th.yasumatsu@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d7b132e62 ]
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f6 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 704e624f7b ]
On s390, the following build warning occurs:
drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in
conversion from 'long unsigned int' to 'int' changes value from
'18446744073709551584' to '-32' [-Woverflow]
844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE)
This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is
already 64-byte aligned) on some architectures, actually gets ALIGN'd up
to 512 bytes in the s390 case.
So then, when this is invoked:
MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE)
...that turns into:
704 - 224 - 512 == -32
...which is not a good frame size to end up with! The warning above is a
bit lucky: it notices a signed/unsigned bad behavior here, which leads
to the real problem of a frame that is too short for its contents.
Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is
just exactly big enough. (The other values can't readily be changed
without causing a lot of other problems.)
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Cc: Sven Auhagen <sven.auhagen@voleatech.de>
Cc: Matteo Croce <mcroce@microsoft.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aff51c5da3 ]
Add the missing RxUnicast counter.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38ea9def5b ]
It should be added kfree_skb_list() when err is not equal to zero
in nf_br_ip_fragment().
v2: keep this aligned with IPv6.
v3: modify iter.frag_list to iter.frag.
Fixes: 3c171f496e ("netfilter: bridge: add connection tracking system")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b353bbeae ]
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 798a315fc3 ]
Some pin doesn't support PUPD register, if it fails and fallbacks with
bias_set_combo case, it will call mtk_pinconf_bias_set_pupd_r1_r0() to
modify the PUPD pin again.
Since the general bias set are either PU/PD or PULLSEL/PULLEN, try
bias_set or bias_set_rev1 for the other fallback case. If the pin
doesn't support neither PU/PD nor PULLSEL/PULLEN, it will return
-ENOTSUPP.
Fixes: 81bd1579b4 ("pinctrl: mediatek: Fix fallback call path")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20210701080955.2660294-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b93dfa6bda upstream.
Fix the NFIT parsing code to treat a 0 index in a SPA Range Structure as
a special case and not match Region Mapping Structures that use 0 to
indicate that they are not mapped. Without this fix some platform BIOS
descriptions of "virtual disk" ranges do not result in the pmem driver
attaching to the range.
Details:
In addition to typical persistent memory ranges, the ACPI NFIT may also
convey "virtual" ranges. These ranges are indicated by a UUID in the SPA
Range Structure of UUID_VOLATILE_VIRTUAL_DISK, UUID_VOLATILE_VIRTUAL_CD,
UUID_PERSISTENT_VIRTUAL_DISK, or UUID_PERSISTENT_VIRTUAL_CD. The
critical difference between virtual ranges and UUID_PERSISTENT_MEMORY,
is that virtual do not support associations with Region Mapping
Structures. For this reason the "index" value of virtual SPA Range
Structures is allowed to be 0. If a platform BIOS decides to represent
NVDIMMs with disconnected "Region Mapping Structures" (range-index ==
0), the kernel may falsely associate them with standalone ranges where
the "SPA Range Structure Index" is also zero. When this happens the
driver may falsely require labels where "virtual disks" are expected to
be label-less. I.e. "label-less" is where the namespace-range ==
region-range and the pmem driver attaches with no user action to create
a namespace.
Cc: Jacek Zloch <jacek.zloch@intel.com>
Cc: Lukasz Sobieraj <lukasz.sobieraj@intel.com>
Cc: "Lee, Chun-Yi" <jlee@suse.com>
Cc: <stable@vger.kernel.org>
Fixes: c2f32acdf8 ("acpi, nfit: treat virtual ramdisk SPA as pmem region")
Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com>
Reported-by: Damian Bassa <damian.bassa@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/162870796589.2521182.1240403310175570220.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf2ba43221 upstream.
Function ceph_check_delayed_caps() is called from the mdsc->delayed_work
workqueue and it can be kept looping for quite some time if caps keep
being added back to the mdsc->cap_delay_list. This may result in the
watchdog tainting the kernel with the softlockup flag.
This patch breaks this loop if the caps have been recently (i.e. during
the loop execution). Any new caps added to the list will be handled in
the next run.
Also, allow schedule_delayed() callers to explicitly set the delay value
instead of defaulting to 5s, so we can ensure that it runs soon
afterward if it looks like there is more work.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46284
Signed-off-by: Luis Henriques <lhenriques@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a715e8040 upstream.
FPU_STATUS register contains FP exception flags bits which are updated
by core as side-effect of FP instructions but can also be manually
wiggled such as by glibc C99 functions fe{raise,clear,test}except() etc.
To effect the update, the programming model requires OR'ing FWE
bit (31). This bit is write-only and RAZ, meaning it is effectively
auto-cleared after write and thus needs to be set everytime: which
is how glibc implements this.
However there's another usecase of FPU_STATUS update, at the time of
Linux task switch when incoming task value needs to be programmed into
the register. This was added as part of f45ba2bd6d ("ARCv2:
fpu: preserve userspace fpu state") which missed OR'ing FWE bit,
meaning the new value is effectively not being written at all.
This patch remedies that.
Interestingly, this snafu was not caught in interm glibc testing as the
race window which relies on a specific exception bit to be set/clear is
really small specially when it nvolves context switch.
Fortunately this was caught by glibc's math/test-fenv-tls test which
repeatedly set/clear exception flags in a big loop, concurrently in main
program and also in a thread.
Fixes: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/54
Fixes: f45ba2bd6d ("ARCv2: fpu: preserve userspace fpu state")
Cc: stable@vger.kernel.org #5.6+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acc68b8d2a upstream.
The CPSW switchdev driver inherited fix from commit 9421c90150 ("net:
ethernet: ti: cpsw: fix min eth packet size") which changes min TX packet
size to 64bytes (VLAN_ETH_ZLEN, excluding ETH_FCS). It was done to fix HW
packed drop issue when packets are sent from Host to the port with PVID and
un-tagging enabled. Unfortunately this breaks some other non-switch
specific use-cases, like:
- [1] CPSW port as DSA CPU port with DSA-tag applied at the end of the
packet
- [2] Some industrial protocols, which expects min TX packet size 60Bytes
(excluding FCS).
Fix it by configuring min TX packet size depending on driver mode
- 60Bytes (ETH_ZLEN) for multi mac (dual-mac) mode
- 64Bytes (VLAN_ETH_ZLEN) for switch mode
and update it during driver mode change and annotate with
READ_ONCE()/WRITE_ONCE() as it can be read by napi while writing.
[1] https://lore.kernel.org/netdev/20210531124051.GA15218@cephalopod/
[2] https://e2e.ti.com/support/arm/sitara_arm/f/791/t/701669
Cc: stable@vger.kernel.org
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Reported-by: Ben Hutchings <ben.hutchings@essensium.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d3fc01796 upstream.
We used to follow the rule earlier that the create SD context
always be a multiple of 8. However, with the change:
cifs: refactor create_sd_buf() and and avoid corrupting the buffer
...we recompute the length, and we failed that rule.
Fixing that with this change.
Cc: <stable@vger.kernel.org> # v5.10+
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ff25ed6c upstream.
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c39ca6885 upstream.
The tlv320aic31xx driver relies on regcache_sync() to restore the register
contents after going to _BIAS_OFF, for example during system suspend. This
does not work for the jack detection configuration since that is configured
via the same register that status is read back from so the register is
volatile and not cached. This can also cause issues during init if the jack
detection ends up getting set up before the CODEC is initially brought out
of _BIAS_OFF, we will reset the CODEC and resync the cache as part of that
process.
Fix this by explicitly reapplying the jack detection configuration after
resyncing the register cache during power on.
This issue was found by an engineer working off-list on a product
kernel, I just wrote up the upstream fix.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210723180200.25105-1-broonie@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827f3164aa upstream.
Along with the transition to the managed PCM buffers, the driver now
accepts the dynamically allocated buffer, while it still kept the
reference to the old preallocated buffer address. This patch corrects
to the right reference via runtime->dma_addr.
(Although this might have been already buggy before the cleanup with
the managed buffer, let's put Fixes tag to point that; it's a corner
case, after all.)
Fixes: d55894bc27 ("ASoC: uniphier: Use managed buffer allocation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210728112353.6675-5-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0d62baa7f upstream.
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn:
argument 4 to %08lX specifier is cast from pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427215d85e upstream.
Add the following checks from __do_loopback() to clone_private_mount() as
well:
- verify that the mount is in the current namespace
- verify that there are no locked children
Reported-by: Alois Wohlschlager <alois1@gmx-topmail.de>
Fixes: c771d683a6 ("vfs: introduce clone_private_mount()")
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3125f26c51 upstream.
When registering new ppp interface via PPPIOCNEWUNIT ioctl then kernel has
to choose interface name as this ioctl API does not support specifying it.
Kernel in this case register new interface with name "ppp<id>" where <id>
is the ppp unit id, which can be obtained via PPPIOCGUNIT ioctl. This
applies also in the case when registering new ppp interface via rtnl
without supplying IFLA_IFNAME.
PPPIOCNEWUNIT ioctl allows to specify own ppp unit id which will kernel
assign to ppp interface, in case this ppp id is not already used by other
ppp interface.
In case user does not specify ppp unit id then kernel choose the first free
ppp unit id. This applies also for case when creating ppp interface via
rtnl method as it does not provide a way for specifying own ppp unit id.
If some network interface (does not have to be ppp) has name "ppp<id>"
with this first free ppp id then PPPIOCNEWUNIT ioctl or rtnl call fails.
And registering new ppp interface is not possible anymore, until interface
which holds conflicting name is renamed. Or when using rtnl method with
custom interface name in IFLA_IFNAME.
As list of allocated / used ppp unit ids is not possible to retrieve from
kernel to userspace, userspace has no idea what happens nor which interface
is doing this conflict.
So change the algorithm how ppp unit id is generated. And choose the first
number which is not neither used as ppp unit id nor in some network
interface with pattern "ppp<id>".
This issue can be simply reproduced by following pppd call when there is no
ppp interface registered and also no interface with name pattern "ppp<id>":
pppd ifname ppp1 +ipv6 noip noauth nolock local nodetach pty "pppd +ipv6 noip noauth nolock local nodetach notty"
Or by creating the one ppp interface (which gets assigned ppp unit id 0),
renaming it to "ppp1" and then trying to create a new ppp interface (which
will always fails as next free ppp unit id is 1, but network interface with
name "ppp1" exists).
This patch fixes above described issue by generating new and new ppp unit
id until some non-conflicting id with network interfaces is generated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
