[ Upstream commit 29341c6c18b8ad2a9a4a68a61be7e1272d842f21 ]
A previous commit changed the '#sound-dai-cells' property for the
kirkwood audio controller from 1 to 0 in the kirkwood.dtsi file,
but did not update the corresponding 'sound-dai' property in the
kirkwood-openrd-client.dts file.
This created a mismatch, causing a dtbs_check validation error where
the dts provides one cell (<&audio0 0>) while the .dtsi expects zero.
Remove the extraneous cell from the 'sound-dai' property to fix the
schema validation warning and align with the updated binding.
Fixes: e662e70fa4 ("arm: dts: kirkwood: fix error in #sound-dai-cells size")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a50342f976d25aace73ff551845ce89406f48f35 ]
The TMU has two temperature measurement sites located on the chip. The
probe 0 is located inside of the ANAMIX, while the probe 1 is located near
the ARM core. This has been confirmed by checking with HW design team and
checking RTL code.
So correct the {cpu,soc}-thermal sensor index.
Fixes: 30cdd62dce ("arm64: dts: imx8mp: Add thermal zones support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98c6d259319ecf6e8d027abd3f14b81324b8c0ad ]
Patch series "mm: better GUP pin lru_add_drain_all()", v2.
Series of lru_add_drain_all()-related patches, arising from recent mm/gup
migration report from Will Deacon.
This patch (of 5):
Will Deacon reports:-
When taking a longterm GUP pin via pin_user_pages(),
__gup_longterm_locked() tries to migrate target folios that should not be
longterm pinned, for example because they reside in a CMA region or
movable zone. This is done by first pinning all of the target folios
anyway, collecting all of the longterm-unpinnable target folios into a
list, dropping the pins that were just taken and finally handing the list
off to migrate_pages() for the actual migration.
It is critically important that no unexpected references are held on the
folios being migrated, otherwise the migration will fail and
pin_user_pages() will return -ENOMEM to its caller. Unfortunately, it is
relatively easy to observe migration failures when running pKVM (which
uses pin_user_pages() on crosvm's virtual address space to resolve stage-2
page faults from the guest) on a 6.15-based Pixel 6 device and this
results in the VM terminating prematurely.
In the failure case, 'crosvm' has called mlock(MLOCK_ONFAULT) on its
mapping of guest memory prior to the pinning. Subsequently, when
pin_user_pages() walks the page-table, the relevant 'pte' is not present
and so the faulting logic allocates a new folio, mlocks it with
mlock_folio() and maps it in the page-table.
Since commit 2fbb0c10d1 ("mm/munlock: mlock_page() munlock_page() batch
by pagevec"), mlock/munlock operations on a folio (formerly page), are
deferred. For example, mlock_folio() takes an additional reference on the
target folio before placing it into a per-cpu 'folio_batch' for later
processing by mlock_folio_batch(), which drops the refcount once the
operation is complete. Processing of the batches is coupled with the LRU
batch logic and can be forcefully drained with lru_add_drain_all() but as
long as a folio remains unprocessed on the batch, its refcount will be
elevated.
This deferred batching therefore interacts poorly with the pKVM pinning
scenario as we can find ourselves in a situation where the migration code
fails to migrate a folio due to the elevated refcount from the pending
mlock operation.
Hugh Dickins adds:-
!folio_test_lru() has never been a very reliable way to tell if an
lru_add_drain_all() is worth calling, to remove LRU cache references to
make the folio migratable: the LRU flag may be set even while the folio is
held with an extra reference in a per-CPU LRU cache.
5.18 commit 2fbb0c10d1 may have made it more unreliable. Then 6.11
commit 33dfe9204f29 ("mm/gup: clear the LRU flag of a page before adding
to LRU batch") tried to make it reliable, by moving LRU flag clearing; but
missed the mlock/munlock batches, so still unreliable as reported.
And it turns out to be difficult to extend 33dfe9204f29's LRU flag
clearing to the mlock/munlock batches: if they do benefit from batching,
mlock/munlock cannot be so effective when easily suppressed while !LRU.
Instead, switch to an expected ref_count check, which was more reliable
all along: some more false positives (unhelpful drains) than before, and
never a guarantee that the folio will prove migratable, but better.
Note on PG_private_2: ceph and nfs are still using the deprecated
PG_private_2 flag, with the aid of netfs and filemap support functions.
Although it is consistently matched by an increment of folio ref_count,
folio_expected_ref_count() intentionally does not recognize it, and ceph
folio migration currently depends on that for PG_private_2 folios to be
rejected. New references to the deprecated flag are discouraged, so do
not add it into the collect_longterm_unpinnable_folios() calculation: but
longterm pinning of transiently PG_private_2 ceph and nfs folios (an
uncommon case) may invoke a redundant lru_add_drain_all(). And this makes
easy the backport to earlier releases: up to and including 6.12, btrfs
also used PG_private_2, but without a ref_count increment.
Note for stable backports: requires 6.16 commit 86ebd50224c0 ("mm:
add folio_expected_ref_count() for reference count calculation").
Link: https://lkml.kernel.org/r/41395944-b0e3-c3ac-d648-8ddd70451d28@google.com
Link: https://lkml.kernel.org/r/bd1f314a-fca1-8f19-cac0-b936c9614557@google.com
Fixes: 9a4e9f3b2d ("mm: update get_user_pages_longterm to migrate pages allocated from CMA region")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Will Deacon <will@kernel.org>
Closes: https://lore.kernel.org/linux-mm/20250815101858.24352-1-will@kernel.org/
Acked-by: Kiryl Shutsemau <kas@kernel.org>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@kernel.org>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Chris Li <chrisl@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Keir Fraser <keirf@google.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Li Zhe <lizhe.67@bytedance.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Shivank Garg <shivankg@amd.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Wei Xu <weixugc@google.com>
Cc: yangge <yangge1116@126.com>
Cc: Yuanchu Xie <yuanchu@google.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Clean cherry-pick now into this tree ]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86ebd50224c0734d965843260d0dc057a9431c61 ]
Patch series " JFS: Implement migrate_folio for jfs_metapage_aops" v5.
This patchset addresses a warning that occurs during memory compaction due
to JFS's missing migrate_folio operation. The warning was introduced by
commit 7ee3647243e5 ("migrate: Remove call to ->writepage") which added
explicit warnings when filesystem don't implement migrate_folio.
The syzbot reported following [1]:
jfs_metapage_aops does not implement migrate_folio
WARNING: CPU: 1 PID: 5861 at mm/migrate.c:955 fallback_migrate_folio mm/migrate.c:953 [inline]
WARNING: CPU: 1 PID: 5861 at mm/migrate.c:955 move_to_new_folio+0x70e/0x840 mm/migrate.c:1007
Modules linked in:
CPU: 1 UID: 0 PID: 5861 Comm: syz-executor280 Not tainted 6.15.0-rc1-next-20250411-syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025
RIP: 0010:fallback_migrate_folio mm/migrate.c:953 [inline]
RIP: 0010:move_to_new_folio+0x70e/0x840 mm/migrate.c:1007
To fix this issue, this series implement metapage_migrate_folio() for JFS
which handles both single and multiple metapages per page configurations.
While most filesystems leverage existing migration implementations like
filemap_migrate_folio(), buffer_migrate_folio_norefs() or
buffer_migrate_folio() (which internally used folio_expected_refs()),
JFS's metapage architecture requires special handling of its private data
during migration. To support this, this series introduce the
folio_expected_ref_count(), which calculates external references to a
folio from page/swap cache, private data, and page table mappings.
This standardized implementation replaces the previous ad-hoc
folio_expected_refs() function and enables JFS to accurately determine
whether a folio has unexpected references before attempting migration.
Implement folio_expected_ref_count() to calculate expected folio reference
counts from:
- Page/swap cache (1 per page)
- Private data (1)
- Page table mappings (1 per map)
While originally needed for page migration operations, this improved
implementation standardizes reference counting by consolidating all
refcount contributors into a single, reusable function that can benefit
any subsystem needing to detect unexpected references to folios.
The folio_expected_ref_count() returns the sum of these external
references without including any reference the caller itself might hold.
Callers comparing against the actual folio_ref_count() must account for
their own references separately.
Link: https://syzkaller.appspot.com/bug?extid=8bb6fd945af4e0ad9299 [1]
Link: https://lkml.kernel.org/r/20250430100150.279751-1-shivankg@amd.com
Link: https://lkml.kernel.org/r/20250430100150.279751-2-shivankg@amd.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Shivank Garg <shivankg@amd.com>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Co-developed-by: David Hildenbrand <david@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: Donet Tom <donettom@linux.ibm.com>
Cc: Jane Chu <jane.chu@oracle.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 98c6d259319e ("mm/gup: check ref_count instead of lru before migration")
[ Take the new function in mm.h, removing "const" from its parameter to stop
build warnings; but avoid all the conflicts of using it in mm/migrate.c. ]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517f496e1e61bd169d585dab4dd77e7147506322 ]
After commit 1aaf8c122918 ("mm: gup: fix infinite loop within
__get_longterm_locked") we are able to longterm pin folios that are not
supposed to get longterm pinned, simply because they temporarily have the
LRU flag cleared (esp. temporarily isolated).
For example, two __get_longterm_locked() callers can race, or
__get_longterm_locked() can race with anything else that temporarily
isolates folios.
The introducing commit mentions the use case of a driver that uses
vm_ops->fault to insert pages allocated through cma_alloc() into the page
tables, assuming they can later get longterm pinned. These pages/ folios
would never have the LRU flag set and consequently cannot get isolated.
There is no known in-tree user making use of that so far, fortunately.
To handle that in the future -- and avoid retrying forever to
isolate/migrate them -- we will need a different mechanism for the CMA
area *owner* to indicate that it actually already allocated the page and
is fine with longterm pinning it. The LRU flag is not suitable for that.
Probably we can lookup the relevant CMA area and query the bitmap; we only
have have to care about some races, probably. If already allocated, we
could just allow longterm pinning)
Anyhow, let's fix the "must not be longterm pinned" problem first by
reverting the original commit.
Link: https://lkml.kernel.org/r/20250611131314.594529-1-david@redhat.com
Fixes: 1aaf8c122918 ("mm: gup: fix infinite loop within __get_longterm_locked")
Signed-off-by: David Hildenbrand <david@redhat.com>
Closes: https://lore.kernel.org/all/20250522092755.GA3277597@tiffany/
Reported-by: Hyesoo Yu <hyesoo.yu@samsung.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Peter Xu <peterx@redhat.com>
Cc: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Cc: Aijun Sun <aijun.sun@unisoc.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Revert v6.6.79 commit 933b08c0ed ]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85fe9f565d2d5af95ac2bbaa5082b8ce62b039f5 ]
Fix a bug where the driver's event subscription logic for SRQ-related
events incorrectly sets obj_type for RMP objects.
When subscribing to SRQ events, get_legacy_obj_type() did not handle
the MLX5_CMD_OP_CREATE_RMP case, which caused obj_type to be 0
(default).
This led to a mismatch between the obj_type used during subscription
(0) and the value used during notification (1, taken from the event's
type field). As a result, event mapping for SRQ objects could fail and
event notification would not be delivered correctly.
This fix adds handling for MLX5_CMD_OP_CREATE_RMP in get_legacy_obj_type,
returning MLX5_EVENT_QUEUE_TYPE_RQ so obj_type is consistent between
subscription and notification.
Fixes: 7597385371 ("IB/mlx5: Enable subscription for device events over DEVX")
Link: https://patch.msgid.link/r/8f1048e3fdd1fde6b90607ce0ed251afaf8a148c.1755088962.git.leon@kernel.org
Signed-off-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Edward Srouji <edwards@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9df1755485dd90a89656e8a21ec4d71c909fa30 ]
The vendor Comtrue Inc. (0x2fc6) produces USB audio chipsets like
the CT7601 which are capable of Native DSD playback.
This patch adds QUIRK_FLAG_DSD_RAW for Comtrue (VID 0x2fc6), which enables
native DSD playback (DSD_U32_LE) on their USB Audio device. This has been
verified under Ubuntu 25.04 with JRiver.
Signed-off-by: noble.yang <noble.yang@comtrue-inc.com>
Link: https://patch.msgid.link/20250731110614.4070-1-noble228@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ca30a1b007d5fefb5752428f852a2d8d7219c1c ]
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Fixes: 79d561c4ec04 ("ALSA: usb-audio: Add mixer quirk for Sony DualSense PS5")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20250612060228.1518028-1-nichen@iscas.ac.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79d561c4ec0497669f19a9550cfb74812f60938b ]
The Sony DualSense wireless controller (PS5) features an internal mono
speaker, but it also provides a 3.5mm jack socket for headphone output
and headset microphone input.
Since this is a UAC1 device, it doesn't advertise any jack detection
capability. However, the controller is able to report HP & MIC insert
events via HID, i.e. through a dedicated input device managed by the
hid-playstation driver.
Add a quirk to create the jack controls for headphone and headset mic,
respectively, and setup an input handler for each of them in order to
intercept the related hotplug events.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250526-dualsense-alsa-jack-v1-9-1a821463b632@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cea7425595697802e8d55a322a251999554b8b1 ]
Adding a memory barrier before wake_up() in
snd_usb_soundblaster_remote_complete() is supposed to ensure the write
to mixer->rc_code is visible in wait_event_interruptible() from
snd_usb_sbrc_hwdep_read().
However, this is not really necessary, since wake_up() is just a wrapper
over __wake_up() which already executes a full memory barrier before
accessing the state of the task to be waken up.
Drop the redundant call to wmb() and implicitly fix the checkpatch
complaint:
WARNING: memory barrier without comment
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250526-dualsense-alsa-jack-v1-8-1a821463b632@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 853a57ba263adfecf4430b936d6862bc475b4bb5 ]
In kernel v6.5, several functions were added to the cdev layer. This
required updating the default version of subsystem ABI up to 6, but
this requirement was overlooked.
This commit updates the version accordingly.
Fixes: 6add87e976 ("firewire: cdev: add new version of ABI to notify time stamp at request/response subaction of transaction#")
Link: https://lore.kernel.org/r/20250920025148.163402-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cb782ff3c62c837e4984b6ae9f5d9a423cd5088 ]
Previous checks incorrectly tested the DMA addresses (dma_handle) for
NULL. Since dma_alloc_coherent() returns the CPU (virtual) address, the
NULL check should be performed on the *_base_addr pointer to correctly
detect allocation failures.
Update the checks to validate sqe_base_addr and cqe_base_addr instead of
sqe_dma_addr and cqe_dma_addr.
Fixes: 4682abfae2 ("scsi: ufs: core: mcq: Allocate memory for MCQ mode")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Revert commit ce8da5d13d which is commit
7e49538288e523427beedd26993d446afef1a6fb upstream.
This reverts commit ce8da5d13d ("loop: Avoid updating block size under
exclusive owner") for the 6.6 kernel, because if the LTP ioctl_loop06 test is
run with this patch in place, the test will fail, it leaves the host unable to
kexec into the kernel again (hangs forever) and "losetup -a" will hang on
attempting to access the /dev/loopN device that the test has set up.
The patch doesn't need to be reverted from 6.12, as it works fine there.
Cc: stable@vger.kernel.org # 6.6.x
Signed-off-by: Eric Hagberg <ehagberg@janestreet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4477b39c32fdc03363affef4b11d48391e6dc9ff ]
Commit 3a7e02c040b1 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.
The complexity of those macros stems from two issues:
(a) trying to use them in situations that require a C constant
expression (in static initializers and for array sizes)
(b) the type sanity checking
and MIN_T/MAX_T avoids both of these issues.
Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.
But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.
However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.
This does exactly that.
Which in turn will then allow for much simpler implementations of
min_t()/max_t(). All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.
We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.
Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 017fa3e89187848fd056af757769c9e66ac3e93d ]
This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.
That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a7e02c040b130b5545e4b115aada7bacd80a2b6 ]
The minmax infrastructure is overkill for simple constants, and can
cause huge expansions because those simple constants are then used by
other things.
For example, 'pageblock_order' is a core VM constant, but because it was
implemented using 'min_t()' and all the type-checking that involves, it
actually expanded to something like 2.5kB of preprocessor noise.
And when that simple constant was then used inside other expansions:
#define pageblock_nr_pages (1UL << pageblock_order)
#define pageblock_start_pfn(pfn) ALIGN_DOWN((pfn), pageblock_nr_pages)
and we then use that inside a 'max()' macro:
case ISOLATE_SUCCESS:
update_cached = false;
last_migrated_pfn = max(cc->zone->zone_start_pfn,
pageblock_start_pfn(cc->migrate_pfn - 1));
the end result was that one statement expanding to 253kB in size.
There are probably other cases of this, but this one case certainly
stood out.
I've added 'MIN_T()' and 'MAX_T()' macros for this kind of "core simple
constant with specific type" use. These macros skip the type checking,
and as such need to be very sparingly used only for obvious cases that
have active issues like this.
Reported-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Link: https://lore.kernel.org/all/36aa2cad-1db1-4abf-8dd2-fb20484aabc3@lucifer.local/
Cc: David Laight <David.Laight@aculab.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eliav Farber <farbere@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f755be0b1ff429a2ecf709beeb1bcd7abc111c2b ]
When the MPTCP DATA FIN have been ACKed, there is no more MPTCP related
metadata to exchange, and all subflows can be safely shutdown.
Before this patch, the subflows were actually terminated at 'close()'
time. That's certainly fine most of the time, but not when the userspace
'shutdown()' a connection, without close()ing it. When doing so, the
subflows were staying in LAST_ACK state on one side -- and consequently
in FIN_WAIT2 on the other side -- until the 'close()' of the MPTCP
socket.
Now, when the DATA FIN have been ACKed, all subflows are shutdown. A
consequence of this is that the TCP 'FIN' flag can be set earlier now,
but the end result is the same. This affects the packetdrill tests
looking at the end of the MPTCP connections, but for a good reason.
Note that tcp_shutdown() will check the subflow state, so no need to do
that again before calling it.
Fixes: 3721b9b646 ("mptcp: Track received DATA_FIN sequence number and add related helpers")
Cc: stable@vger.kernel.org
Fixes: 16a9a9da17 ("mptcp: Add helper to process acks of DATA_FIN")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250912-net-mptcp-fix-sft-connect-v1-1-d40e77cbbf02@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When commit fa78e9b606a472495ef5b6b3d8b45c37f7727f9d upstream was
backported to LTS branches linux-6.12.y and linux-6.6.y, the SPI regmap
config fix got applied to the I2C regmap config. Most likely due to a new
RTC get/set parm feature introduced in 6.14 causing regmap config sections
in the buttom of the driver to move. LTS branch linux-6.1.y and earlier
does not have PCF2131 device support.
Issue can be seen in buttom of this diff in stable/linux.git tree:
git diff master..linux-6.12.y -- drivers/rtc/rtc-pcf2127.c
Fixes: ee61aec8529e ("rtc: pcf2127: fix SPI command byte for PCF2131")
Fixes: 5cdd1f7340 ("rtc: pcf2127: fix SPI command byte for PCF2131")
Cc: stable@vger.kernel.org
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Elena Popa <elena.popa@nxp.com>
Cc: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1e56310b40fd2e7e0b9493da9ff488af145bdd0c ]
The AMD IOMMU host page table implementation supports dynamic page table levels
(up to 6 levels), starting with a 3-level configuration that expands based on
IOVA address. The kernel maintains a root pointer and current page table level
to enable proper page table walks in alloc_pte()/fetch_pte() operations.
The IOMMU IOVA allocator initially starts with 32-bit address and onces its
exhuasted it switches to 64-bit address (max address is determined based
on IOMMU and device DMA capability). To support larger IOVA, AMD IOMMU
driver increases page table level.
But in unmap path (iommu_v1_unmap_pages()), fetch_pte() reads
pgtable->[root/mode] without lock. So its possible that in exteme corner case,
when increase_address_space() is updating pgtable->[root/mode], fetch_pte()
reads wrong page table level (pgtable->mode). It does compare the value with
level encoded in page table and returns NULL. This will result is
iommu_unmap ops to fail and upper layer may retry/log WARN_ON.
CPU 0 CPU 1
------ ------
map pages unmap pages
alloc_pte() -> increase_address_space() iommu_v1_unmap_pages() -> fetch_pte()
pgtable->root = pte (new root value)
READ pgtable->[mode/root]
Reads new root, old mode
Updates mode (pgtable->mode += 1)
Since Page table level updates are infrequent and already synchronized with a
spinlock, implement seqcount to enable lock-free read operations on the read path.
Fixes: 754265bcab ("iommu/amd: Fix race in increase_address_space()")
Reported-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Cc: stable@vger.kernel.org
Cc: Joao Martins <joao.m.martins@oracle.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Vasant Hegde <vasant.hegde@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
[ Adapted pgtable->mode and pgtable->root to use domain->iop.mode and domain->iop.root ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5c98e8b1398534ae1feb6e95e2d3ee5215538ed ]
Pending requests will be flushed on disconnect, and the corresponding
TRBs will be turned into No-op TRBs, which are ignored by the xHC
controller once it starts processing the ring.
If the USB debug cable repeatedly disconnects before ring is started
then the ring will eventually be filled with No-op TRBs.
No new transfers can be queued when the ring is full, and driver will
print the following error message:
"xhci_hcd 0000:00:14.0: failed to queue trbs"
This is a normal case for 'in' transfers where TRBs are always enqueued
in advance, ready to take on incoming data. If no data arrives, and
device is disconnected, then ring dequeue will remain at beginning of
the ring while enqueue points to first free TRB after last cancelled
No-op TRB.
s
Solve this by reinitializing the rings when the debug cable disconnects
and DbC is leaving the configured state.
Clear the whole ring buffer and set enqueue and dequeue to the beginning
of ring, and set cycle bit to its initial state.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 220a0ffde02f962c13bc752b01aa570b8c65a37b ]
Decouple allocation of endpoint ring buffer from initialization
of the buffer, and initialization of endpoint context parts from
from the rest of the contexts.
It allows driver to clear up and reinitialize endpoint rings
after disconnect without reallocating everything.
This is a prerequisite for the next patch that prevents the transfer
ring from filling up with cancelled (no-op) TRBs if a debug cable is
reconnected several times without transferring anything.
Cc: stable@vger.kernel.org
Fixes: dfba2174dc ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250902105306.877476-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21bf6fc47a1e45031ba8a7084343b7cfd09ed1d3 ]
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231009172923.2457844-15-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 64961557efa1 ("phy: ti: omap-usb2: fix device leak at unbind")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24733e193a0d68f20d220e86da0362460c9aa812 upstream.
The previous commit adds the MPTCP_PM_EV_FLAG_DENY_JOIN_ID0 flag. Make
sure it is correctly announced by the other peer when it has been
received.
pm_nl_ctl will now display 'deny_join_id0:1' when monitoring the events,
and when this flag was set by the other peer.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250912-net-mptcp-pm-uspace-deny_join_id0-v1-3-40171884ade8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Conflict in userspace_pm.sh, because of a difference in the context,
introduced by commit c66fb480a330 ("selftests: userspace pm: avoid
relaunching pm events"), which is not in this version. The same lines
can still be added at the same place. ]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2293c57484ae64c9a3c847c8807db8c26a3a4d41 upstream.
During the connection establishment, a peer can tell the other one that
it cannot establish new subflows to the initial IP address and port by
setting the 'C' flag [1]. Doing so makes sense when the sender is behind
a strict NAT, operating behind a legacy Layer 4 load balancer, or using
anycast IP address for example.
When this 'C' flag is set, the path-managers must then not try to
establish new subflows to the other peer's initial IP address and port.
The in-kernel PM has access to this info, but the userspace PM didn't.
The RFC8684 [1] is strict about that:
(...) therefore the receiver MUST NOT try to open any additional
subflows toward this address and port.
So it is important to tell the userspace about that as it is responsible
for the respect of this flag.
When a new connection is created and established, the Netlink events
now contain the existing but not currently used 'flags' attribute. When
MPTCP_PM_EV_FLAG_DENY_JOIN_ID0 is set, it means no other subflows
to the initial IP address and port -- info that are also part of the
event -- can be established.
Link: https://datatracker.ietf.org/doc/html/rfc8684#section-3.1-20.6 [1]
Fixes: 702c2f646d ("mptcp: netlink: allow userspace-driven subflow establishment")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/532
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250912-net-mptcp-pm-uspace-deny_join_id0-v1-2-40171884ade8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Conflicts in mptcp_pm.yaml, and mptcp_pm.h, because these files have
been added later by commit bc8aeb2045e2 ("Documentation: netlink: add
a YAML spec for mptcp"), and commit 9d1ed17f93ce ("uapi: mptcp: use
header file generated from YAML spec"), which are not in this version.
Applying the same modifications, but only in mptcp.h.
Conflict in pm_netlink.c, because of a difference in the context,
introduced by commit b9f4554356f6 ("mptcp: annotate lockless access
for token"), which is not in this version. ]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dd765fae295832934bf28e45dd5a355e0891ed4 upstream.
vmxnet3 does not unregister xdp rxq info in the
vmxnet3_reset_work() code path as vmxnet3_rq_destroy()
is not invoked in this code path. So, we get below message with a
backtrace.
Missing unregister, handled but fix driver
WARNING: CPU:48 PID: 500 at net/core/xdp.c:182
__xdp_rxq_info_reg+0x93/0xf0
This patch fixes the problem by moving the unregister
code of XDP from vmxnet3_rq_destroy() to vmxnet3_rq_cleanup().
Fixes: 54f00cce11 ("vmxnet3: Add XDP support.")
Signed-off-by: Sankararaman Jayaraman <sankararaman.jayaraman@broadcom.com>
Signed-off-by: Ronak Doshi <ronak.doshi@broadcom.com>
Link: https://patch.msgid.link/20250320045522.57892-1-sankararaman.jayaraman@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ Ajay: Modified to apply on v6.6, v6.12 ]
Signed-off-by: Ajay Kaher <ajay.kaher@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9574b2330dbd2b5459b74d3b5e9619d39299fc6f ]
If an error causes af_alg_sendmsg to abort, ctx->merge may contain
a garbage value from the previous loop. This may then trigger a
crash on the next entry into af_alg_sendmsg when it attempts to do
a merge that can't be done.
Fix this by setting ctx->merge to zero near the start of the loop.
Fixes: 8ff590903d ("crypto: algif_skcipher - User-space interface for skcipher operations")
Reported-by: Muhammad Alifa Ramdhan <ramdhan@starlabs.sg>
Reported-by: Bing-Jhong Billy Jheng <billy@starlabs.sg>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3539b1467e94336d5854ebf976d9627bfb65d6c3 upstream.
When running task_work for an exiting task, rather than perform the
issue retry attempt, the task_work is canceled. However, this isn't
done for a ring that has been closed. This can lead to requests being
successfully completed post the ring being closed, which is somewhat
confusing and surprising to an application.
Rather than just check the task exit state, also include the ring
ref state in deciding whether or not to terminate a given request when
run from task_work.
Cc: stable@vger.kernel.org # 6.1+
Link: https://github.com/axboe/liburing/discussions/1459
Reported-by: Benedek Thaler <thaler@thaler.hu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parts of commit b6f58a3f4aa8dba424356c7a69388a81f4459300 upstream.
Backport io_should_terminate_tw() helper to judge whether task_work
should be run or terminated.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d33c3471047fc54966621d19329e6a23ebc8ec50 upstream.
This laptop uses the ALC236 codec with COEF 0x7 and idx 1 to
control the mute LED. Enable the existing quirk for this device.
Signed-off-by: Praful Adiga <praful.adiga@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
