[ Upstream commit 7cf7b2e977 ]
Lower the minimum height to 360 to be consistent with the webcam input of vivid.
The 480 was rather arbitrary but it made it harder to use vivid as a source for
encoding since the default resolution when you load vivid is 640x360.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c616cbee97 upstream.
After the direct dispatch corruption fix, we permanently disallow direct
dispatch of non read/write requests. This works fine off the normal IO
path, as they will be retried like any other failed direct dispatch
request. But for the blk_insert_cloned_request() that only DM uses to
bypass the bottom level scheduler, we always first attempt direct
dispatch. For some types of requests, that's now a permanent failure,
and no amount of retrying will make that succeed. This results in a
livelock.
Instead of making special cases for what we can direct issue, and now
having to deal with DM solving the livelock while still retaining a BUSY
condition feedback loop, always just add a request that has been through
->queue_rq() to the hardware queue dispatch list. These are safe to use
as no merging can take place there. Additionally, if requests do have
prepped data from drivers, we aren't dependent on them not sharing space
in the request structure to safely add them to the IO scheduler lists.
This basically reverts ffe81d4532 and is based on a patch from Ming,
but with the list insert case covered as well.
Fixes: ffe81d4532 ("blk-mq: fix corruption with direct issue")
Cc: stable@vger.kernel.org
Suggested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29e270fc32 upstream.
Got below warning with gcc 8.2 compiler.
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b04114f6f upstream.
By default NFSv3 doesn't support ACL (Access Control Lists)
which might be quite convenient to have so that
mounted NFS behaves exactly as any other local file-system.
In particular missing support of ACL makes umask useless.
This among other thigs fixes Glibc's "nptl/tst-umask1".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Cupertino Miranda <cmiranda@synopsys.com>
Cc: stable@vger.kernel.org #4.14+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7cc40c32a upstream.
Change the default defconfig (used with 'make defconfig') to the ARCv2
nsim_hs_defconfig, and also switch the default Kconfig ISA selection to
ARCv2.
This allows several default defconfigs (e.g. make defconfig, make
allnoconfig, make tinyconfig) to all work with ARCv2 by default.
Note since we change default architecture from ARCompact to ARCv2
it's required to explicitly mention architecture type in ARCompact
defconfigs otherwise ARCv2 will be implied and binaries will be
generated for ARCv2.
Cc: <stable@vger.kernel.org> # 4.4.x
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10950929e9 upstream.
[BUG]
A completely valid btrfs will refuse to mount, with error message like:
BTRFS critical (device sdb2): corrupt leaf: root=2 block=239681536 slot=172 \
bg_start=12018974720 bg_len=10888413184, invalid block group size, \
have 10888413184 expect (0, 10737418240]
This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.
Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.
[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.
__btrfs_alloc_chunk()
|- max_stripe_size = 1G
|- max_chunk_size = 10G
|- data_stripe = 11
|- if (1G * 11 > 10G) {
stripe_size = 976128930;
stripe_size = round_up(976128930, SZ_16M) = 989855744
However the final stripe_size (989855744) * 11 = 10888413184, which is
still larger than 10G.
[FIX]
For the comprehensive check, we need to do the full check at chunk read
time, and rely on bg <-> chunk mapping to do the check.
We could just skip the length check for now.
Fixes: fce466eab7 ("btrfs: tree-checker: Verify block_group_item")
Cc: stable@vger.kernel.org # v4.19+
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac5722c164 upstream.
The cros_ec_keyb_bs array lists buttons and switches together, expecting
that its users will match the appropriate type and bit fields. But
cros_ec_keyb_register_bs() only checks the 'bit' field, which causes
misreported input capabilities in some cases. For example, tablets
(e.g., Scarlet -- a.k.a. Acer Chromebook Tab 10) were reporting a SW_LID
capability, because EC_MKBP_POWER_BUTTON and EC_MKBP_LID_OPEN happen to
share the same bit.
(This has comedic effect on a tablet, in which a power-management daemon
then thinks this "lid" is closed, and so puts the system to sleep as
soon as it boots!)
To fix this, check both the 'ev_type' and 'bit' fields before reporting
the capability.
Tested with a lid (Kevin / Samsung Chromebook Plus) and without a lid
(Scarlet / Acer Chromebook Tab 10).
This error got introduced when porting the feature from the downstream
Chromium OS kernel to be upstreamed.
Fixes: cdd7950e7a ("input: cros_ec_keyb: Add non-matrix buttons and switches")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d55bda1b3e upstream.
"of_get_named_gpio()" returns a negative error value if it fails
and drivers should check for this. This missing check was now
added to the matrix_keypad driver.
In my case "of_get_named_gpio()" returned -EPROBE_DEFER because
the referenced GPIOs belong to an I/O expander, which was not yet
probed at the point in time when the matrix_keypad driver was
loading. Because the driver did not check for errors from the
"of_get_named_gpio()" routine, it was assuming that "-EPROBE_DEFER"
is actually a GPIO number and continued as usual, which led to further
errors like this later on:
WARNING: CPU: 3 PID: 167 at drivers/gpio/gpiolib.c:114
gpio_to_desc+0xc8/0xd0
invalid GPIO -517
Note that the "GPIO number" -517 in the error message above is
actually "-EPROBE_DEFER".
As part of the patch a misleading error message "no platform data defined"
was also removed. This does not lead to information loss because the other
error paths in matrix_keypad_parse_dt() already print an error.
Signed-off-by: Christian Hoff <christian_hoff@gmx.net>
Suggested-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9df39bedbf upstream.
Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eab077aa84 upstream.
In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 598e1a42e9 upstream.
Commit 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
added new RTM_* definitions without properly updating SELinux, this
patch adds the necessary SELinux support.
While there was a BUILD_BUG_ON() in the SELinux code to protect from
exactly this case, it was bypassed in the broken commit. In order to
hopefully prevent this from happening in the future, add additional
comments which provide some instructions on how to resolve the
BUILD_BUG_ON() failures.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Cc: <stable@vger.kernel.org> # 4.19
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30510387a5 upstream.
There is a race condition when accessing kvm->arch.apic_access_page_done.
Due to it, x86_set_memory_region will fail when creating the second vcpu
for a svm guest.
Add a mutex_lock to serialize the accesses to apic_access_page_done.
This lock is also used by vmx for the same purpose.
Signed-off-by: Wei Wang <wawei@amazon.de>
Signed-off-by: Amadeusz Juskowiak <ajusk@amazon.de>
Signed-off-by: Julian Stecklina <jsteckli@amazon.de>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd25cbb2f upstream.
After 2dd4531686 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dd4531686 upstream.
There's an error when compiled with restrict:
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b51072e97 upstream.
Userfaultfd did not create private memory when UFFDIO_COPY was invoked
on a MAP_PRIVATE shmem mapping. Instead it wrote to the shmem file,
even when that had not been opened for writing. Though, fortunately,
that could only happen where there was a hole in the file.
Fix the shmem-backed implementation of UFFDIO_COPY to create private
memory for MAP_PRIVATE mappings. The hugetlbfs-backed implementation
was already correct.
This change is visible to userland, if userfaultfd has been used in
unintended ways: so it introduces a small risk of incompatibility, but
is necessary in order to respect file permissions.
An app that uses UFFDIO_COPY for anything like postcopy live migration
won't notice the difference, and in fact it'll run faster because there
will be no copy-on-write and memory waste in the tmpfs pagecache
anymore.
Userfaults on MAP_PRIVATE shmem keep triggering only on file holes like
before.
The real zeropage can also be built on a MAP_PRIVATE shmem mapping
through UFFDIO_ZEROPAGE and that's safe because the zeropage pte is
never dirty, in turn even an mprotect upgrading the vma permission from
PROT_READ to PROT_READ|PROT_WRITE won't make the zeropage pte writable.
Link: http://lkml.kernel.org/r/20181126173452.26955-3-aarcange@redhat.com
Fixes: 4c27fe4c4c ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e368259ad upstream.
Patch series "userfaultfd shmem updates".
Jann found two bugs in the userfaultfd shmem MAP_SHARED backend: the
lack of the VM_MAYWRITE check and the lack of i_size checks.
Then looking into the above we also fixed the MAP_PRIVATE case.
Hugh by source review also found a data loss source if UFFDIO_COPY is
used on shmem MAP_SHARED PROT_READ mappings (the production usages
incidentally run with PROT_READ|PROT_WRITE, so the data loss couldn't
happen in those production usages like with QEMU).
The whole patchset is marked for stable.
We verified QEMU postcopy live migration with guest running on shmem
MAP_PRIVATE run as well as before after the fix of shmem MAP_PRIVATE.
Regardless if it's shmem or hugetlbfs or MAP_PRIVATE or MAP_SHARED, QEMU
unconditionally invokes a punch hole if the guest mapping is filebacked
and a MADV_DONTNEED too (needed to get rid of the MAP_PRIVATE COWs and
for the anon backend).
This patch (of 5):
We internally used EFAULT to communicate with the caller, switch to
ENOENT, so EFAULT can be used as a non internal retval.
Link: http://lkml.kernel.org/r/20181126173452.26955-2-aarcange@redhat.com
Fixes: 4c27fe4c4c ("userfaultfd: shmem: add shmem_mcopy_atomic_pte for userfaultfd support")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Hugh Dickins <hughd@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bcd3ecab7 upstream.
Since Linux 4.17, calls to drm_crtc_vblank_on/off are mandatory, and we get
a warning when ctrc is disabled :
" driver forgot to call drm_crtc_vblank_off()"
But, the vsync IRQ was not totally disabled due the transient hardware
state and specific interrupt line, thus adding proper IRQ masking from
the HHI system control registers.
The last change fixes a race condition introduced by calling the added
drm_crtc_vblank_on/off when an HPD event occurs from the HDMI connector,
triggering a WARN_ON() in the _atomic_begin() callback when the CRTC
is disabled, thus also triggering a WARN_ON() in drm_vblank_put() :
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/meson/meson_crtc.c:157 meson_crtc_atomic_begin+0x78/0x80
[...]
Call trace:
meson_crtc_atomic_begin+0x78/0x80
drm_atomic_helper_commit_planes+0x140/0x218
drm_atomic_helper_commit_tail+0x38/0x80
commit_tail+0x7c/0x80
drm_atomic_helper_commit+0xdc/0x150
drm_atomic_commit+0x54/0x60
restore_fbdev_mode_atomic+0x198/0x238
restore_fbdev_mode+0x6c/0x1c0
drm_fb_helper_restore_fbdev_mode_unlocked+0x7c/0xf0
drm_fb_helper_set_par+0x34/0x60
drm_fb_helper_hotplug_event.part.28+0xb8/0xc8
drm_fbdev_client_hotplug+0xa4/0xe0
drm_client_dev_hotplug+0x90/0xe0
drm_kms_helper_hotplug_event+0x3c/0x48
drm_helper_hpd_irq_event+0x134/0x168
dw_hdmi_top_thread_irq+0x3c/0x50
[...]
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/drm_vblank.c:1026 drm_vblank_put+0xb4/0xc8
[...]
Call trace:
drm_vblank_put+0xb4/0xc8
drm_crtc_vblank_put+0x24/0x30
drm_atomic_helper_wait_for_vblanks.part.9+0x130/0x2b8
drm_atomic_helper_commit_tail+0x68/0x80
[...]
The issue is that vblank need to be enabled in any occurrence of :
- atomic_enable()
- atomic_begin() and state->enable == true, which was not the case
Moving the CRTC enable code to a common function and calling in one of
these occurrence solves this race condition and makes sure vblank is
enabled in each call to _atomic_begin() from the HPD event leading to
drm_atomic_helper_commit_planes().
To Summarize :
- Make sure that the CRTC code will call the drm_crtc_vblank_on()/off()
- *Really* mask the Vsync IRQ
- Initialize and enable vblank at the first
atomic_begin()/_atomic_enable()
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed typos+added cc for stable]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122160103.10993-1-narmstrong@baylibre.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9e0ab86b2 upstream.
The change fixed huge delay in SST daisy chain and S3 soft hang
observed in 4.19 kernel rebase.
Regression point in drm:
drm/fb-helper: Eliminate the .best_encoder() usage
The aux sequence is altered due to the failure in
drm_connector_for_each_possible_encoder(). The failure is
caused by missing attached encoder in the process of adding
MST connector.
drm_dp_send_enum_path_resources() aux transaction is pushed after
mode probe, which causes conflict to drm_dp_mst_i2c_xfer(),
leading to the transaction timeout.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc25ab0676 upstream.
If the platform has no IO space, ioregs is placed next to the already
allocated regs. In this case, it should not be separately freed.
This prevents a kernel warning from __vunmap "Trying to vfree()
nonexistent vm area" when unloading the driver.
Fixes: 0dd68309b9 ("drm/ast: Try to use MMIO registers when PIO isn't supported")
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cf99a0f31 upstream.
The tracefs file set_graph_function is used to only function graph functions
that are listed in that file (or all functions if the file is empty). The
way this is implemented is that the function graph tracer looks at every
function, and if the current depth is zero and the function matches
something in the file then it will trace that function. When other functions
are called, the depth will be greater than zero (because the original
function will be at depth zero), and all functions will be traced where the
depth is greater than zero.
The issue is that when a function is first entered, and the handler that
checks this logic is called, the depth is set to zero. If an interrupt comes
in and a function in the interrupt handler is traced, its depth will be
greater than zero and it will automatically be traced, even if the original
function was not. But because the logic only looks at depth it may trace
interrupts when it should not be.
The recent design change of the function graph tracer to fix other bugs
caused the depth to be zero while the function graph callback handler is
being called for a longer time, widening the race of this happening. This
bug was actually there for a longer time, but because the race window was so
small it seldom happened. The Fixes tag below is for the commit that widen
the race window, because that commit belongs to a series that will also help
fix the original bug.
Cc: stable@kernel.org
Fixes: 39eb456dac ("function_graph: Use new curr_ret_depth to manage depth instead of curr_ret_stack")
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Tested-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7a691a15 upstream.
If the firmware reports a connection width that is not 1x, 4x, 8x or 12x
it causes the driver to fail during initialization.
To prevent this failure every time a new width is introduced to the RDMA
stack, we will set a default 4x width for these widths which ar unknown to
the driver.
This is needed to allow to run old kernels with new firmware.
Cc: <stable@vger.kernel.org> # 4.1
Fixes: 1b5daf11b0 ("IB/mlx5: Avoid using the MAD_IFC command under ISSI > 0 mode")
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c7a52e4d4 upstream.
After enabling KVM event tracing, almost all of trace_kvm_exit()'s
printk shows
"kvm_exit: IRQ: ..."
even if the actual exception_type is NOT IRQ. More specifically,
trace_kvm_exit() is defined in virt/kvm/arm/trace.h by TRACE_EVENT.
This slight problem may have existed after commit e6753f23d9
("tracepoint: Make rcuidle tracepoint callers use SRCU"). There are
two variables in trace_kvm_exit() and __DO_TRACE() which have the
same name, *idx*. Thus the actual value of *idx* will be overwritten
when tracing. Fix it by adding a simple prefix.
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Wang Haibin <wanghaibin.wang@huawei.com>
Cc: linux-trace-devel@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: e6753f23d9 ("tracepoint: Make rcuidle tracepoint callers use SRCU")
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3054426dc6 upstream.
commit 3f5fe9fef5 ("sched/debug: Fix task state recording/printout")
tried to fix the problem introduced by a previous commit efb40f588b
("sched/tracing: Fix trace_sched_switch task-state printing"). However
the prev_state output in sched_switch is still broken.
task_state_index() uses fls() which considers the LSB as 1. Left
shifting 1 by this value gives an incorrect mapping to the task state.
Fix this by decrementing the value returned by __get_task_state()
before shifting.
Link: http://lkml.kernel.org/r/1540882473-1103-1-git-send-email-pkondeti@codeaurora.org
Cc: stable@vger.kernel.org
Fixes: 3f5fe9fef5 ("sched/debug: Fix task state recording/printout")
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 874bfc6e54 upstream.
Since commit 4378a7d4be ("arm64: implement syscall wrappers")
introduced "__arm64_" prefix to all syscall wrapper symbols in
sys_call_table, syscall tracer can not find corresponding
metadata from syscall name. In the result, we have no syscall
ftrace events on arm64 kernel, and some bpf testcases are failed
on arm64.
To fix this issue, this introduces custom
arch_syscall_match_sym_name() which skips first 8 bytes when
comparing the syscall and symbol names.
Fixes: 4378a7d4be ("arm64: implement syscall wrappers")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38c7b224ce upstream.
New versions of gcc reasonably warn about the odd pattern of
strncpy(p, q, strlen(q));
which really doesn't make sense: the strncpy() ends up being just a slow
and odd way to write memcpy() in this case.
There was a comment about _why_ the code used strncpy - to avoid the
terminating NUL byte, but memcpy does the same and avoids the warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1286ed715 upstream.
New versions of gcc reasonably warn about the odd pattern of
strncpy(p, q, strlen(q));
which really doesn't make sense: the strncpy() ends up being just a slow
and odd way to write memcpy() in this case.
Apparently there was a patch for this floating around earlier, but it
got lost.
Acked-again-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffe81d4532 upstream.
If we attempt a direct issue to a SCSI device, and it returns BUSY, then
we queue the request up normally. However, the SCSI layer may have
already setup SG tables etc for this particular command. If we later
merge with this request, then the old tables are no longer valid. Once
we issue the IO, we only read/write the original part of the request,
not the new state of it.
This causes data corruption, and is most often noticed with the file
system complaining about the just read data being invalid:
[ 235.934465] EXT4-fs error (device sda1): ext4_iget:4831: inode #7142: comm dpkg-query: bad extra_isize 24937 (inode size 256)
because most of it is garbage...
This doesn't happen from the normal issue path, as we will simply defer
the request to the hardware queue dispatch list if we fail. Once it's on
the dispatch list, we never merge with it.
Fix this from the direct issue path by flagging the request as
REQ_NOMERGE so we don't change the size of it before issue.
See also:
https://bugzilla.kernel.org/show_bug.cgi?id=201685
Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 6ce3dd6eec ("blk-mq: issue directly if hw queue isn't busy in case of 'none'")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6484a67729 upstream.
gcc '-Wunused-but-set-variable' warning:
drivers/misc/mic/scif/scif_rma.c: In function 'scif_create_remote_lookup':
drivers/misc/mic/scif/scif_rma.c:373:25: warning:
variable 'vmalloc_num_pages' set but not used [-Wunused-but-set-variable]
'vmalloc_num_pages' should be used to determine if the address is
within the vmalloc range.
Fixes: ba612aa8b4 ("misc: mic: SCIF memory registration and unregistration")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eceb059654 upstream.
This is a longstanding issue: if the vmbus upper-layer drivers try to
consume too many GPADLs, the host may return with an error
0xC0000044 (STATUS_QUOTA_EXCEEDED), but currently we forget to check
the creation_status, and hence we can pass an invalid GPADL handle
into the OPEN_CHANNEL message, and get an error code 0xc0000225 in
open_info->response.open_result.status, and finally we hang in
vmbus_open() -> "goto error_free_info" -> vmbus_teardown_gpadl().
With this patch, we can exit gracefully on STATUS_QUOTA_EXCEEDED.
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ff38bd402 upstream.
If all pages are deleted from the mapping by memory reclaim and also
moved to the cleancache:
__delete_from_page_cache
(no shadow case)
unaccount_page_cache_page
cleancache_put_page
page_cache_delete
mapping->nrpages -= nr
(nrpages becomes 0)
We don't clean the cleancache for an inode after final file truncation
(removal).
truncate_inode_pages_final
check (nrpages || nrexceptional) is false
no truncate_inode_pages
no cleancache_invalidate_inode(mapping)
These way when reading the new file created with same inode we may get
these trash leftover pages from cleancache and see wrong data instead of
the contents of the new file.
Fix it by always doing truncate_inode_pages which is already ready for
nrpages == 0 && nrexceptional == 0 case and just invalidates inode.
[akpm@linux-foundation.org: add comment, per Jan]
Link: http://lkml.kernel.org/r/20181112095734.17979-1-ptikhomirov@virtuozzo.com
Fixes: commit 91b0abe36a ("mm + fs: store shadow entries in page cache")
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe5192ac81 upstream.
Currently, we enable the device before we enable the device trigger. At
high frequencies, this can cause interrupts that don't yet have a poll
function associated with them and are thus treated as spurious. At high
frequencies with level interrupts, this can even cause an interrupt storm
of repeated spurious interrupts (~100,000 on my Beagleboard with the
LSM9DS1 magnetometer). If these repeat too much, the interrupt will get
disabled and the device will stop functioning.
To prevent these problems, enable the device prior to enabling the device
trigger, and disable the divec prior to disabling the trigger. This means
there's no window of time during which the device creates interrupts but we
have no trigger to answer them.
Fixes: 90efe05562 ("iio: st_sensors: harden interrupt handling")
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Tested-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
