[ Upstream commit 44ad820780 ]
Both Luxul's XAP devices (XAP-810 and XAP-1440) are access points that
use a non-default design. They don't include switch but have a single
Ethernet port and BCM54210E PHY connected to the Ethernet controller's
MDIO bus.
Support for those devices regressed due to two changes:
1. Describing MDIO bus with switch
After commit 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125
rev 4 switch") Linux stopped probing for MDIO devices.
2. Dropping hardcoded BCM54210E delays
In commit fea7fda7f5 ("net: phy: broadcom: Fix RGMII delays
configuration for BCM54210E") support for other PHY modes was added but
that requires a proper "phy-mode" value in DT.
Both above changes are correct (they don't need to be reverted or
anything) but they need this fix for DT data to be correct and for Linux
to work properly.
Fixes: 9fb90ae6ca ("ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230713111145.14864-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04544ac0d ]
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-10-krzk@kernel.org
Stable-dep-of: 982655cb0e ("ARM: dts: samsung: s5pv210-smdkv210: correct ethernet reg addresses (split)")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548cb93205 ]
Visible glitches have been observed when running graphics applications on
Linux under Xen hypervisor. Those observations have been confirmed with
failures from kms_pwrite_crc Intel GPU test that verifies data coherency
of DRM frame buffer objects using hardware CRC checksums calculated by
display controllers, exposed to userspace via debugfs. Affected
processing paths have then been identified with new IGT test variants that
mmap the objects using different methods and caching modes [1].
When running as a Xen PV guest, Linux uses Xen provided PAT configuration
which is different from its native one. In particular, Xen specific PTE
encoding of write-combining caching, likely used by graphics applications,
differs from the Linux default one found among statically defined minimal
set of supported modes. Since Xen defines PTE encoding of the WC mode as
_PAGE_PAT, it no longer belongs to the minimal set, depends on correct
handling of _PAGE_PAT bit, and can be mismatched with write-back caching.
When a user calls mmap() for a DRM buffer object, DRM device specific
.mmap file operation, called from mmap_region(), takes care of setting PTE
encoding bits in a vm_page_prot field of an associated virtual memory area
structure. Unfortunately, _PAGE_PAT bit is not preserved when the vma's
.vm_flags are then applied to .vm_page_prot via vm_set_page_prot(). Bits
to be preserved are determined with _PAGE_CHG_MASK symbol that doesn't
cover _PAGE_PAT. As a consequence, WB caching is requested instead of WC
when running under Xen (also, WP is silently changed to WT, and UC
downgraded to UC_MINUS). When running on bare metal, WC is not affected,
but WP and WT extra modes are unintentionally replaced with WC and UC,
respectively.
WP and WT modes, encoded with _PAGE_PAT bit set, were introduced by commit
281d4078be ("x86: Make page cache mode a real type"). Care was taken
to extend _PAGE_CACHE_MASK symbol with that additional bit, but that
symbol has never been used for identification of bits preserved when
applying page protection flags. Support for all cache modes under Xen,
including the problematic WC mode, was then introduced by commit
47591df505 ("xen: Support Xen pv-domains using PAT").
The issue needs to be fixed by including _PAGE_PAT bit into a bitmask used
by pgprot_modify() for selecting bits to be preserved. We can do that
either internally to pgprot_modify() (as initially proposed), or by making
_PAGE_PAT a part of _PAGE_CHG_MASK. If we go for the latter then, since
_PAGE_PAT is the same as _PAGE_PSE, we need to note that _HPAGE_CHG_MASK
-- a huge pmds' counterpart of _PAGE_CHG_MASK, introduced by commit
c489f1257b ("thp: add pmd_modify"), defined as (_PAGE_CHG_MASK |
_PAGE_PSE) -- will no longer differ from _PAGE_CHG_MASK. If such
modification of _PAGE_CHG_MASK was irrelevant to its users then one might
wonder why that new _HPAGE_CHG_MASK symbol was introduced instead of
reusing the existing one with that otherwise irrelevant bit (_PAGE_PSE in
that case) added.
Add _PAGE_PAT to _PAGE_CHG_MASK and _PAGE_PAT_LARGE to _HPAGE_CHG_MASK for
symmetry. Split out common bits from both symbols to a common symbol for
clarity.
[ dhansen: tweak the solution changelog description ]
[1] https://gitlab.freedesktop.org/drm/igt-gpu-tools/-/commit/0f0754413f14
Fixes: 281d4078be ("x86: Make page cache mode a real type")
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/7648
Link: https://lore.kernel.org/all/20230710073613.8006-2-janusz.krzysztofik%40linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20faf2005e ]
gpu->mmu_context is the MMU context of the last job in the HW queue, which
isn't necessarily the same as the context from the bad job. Dump the MMU
context from the scheduler determined bad submit to make it work as intended.
Fixes: 17e4660ae3 ("drm/etnaviv: implement per-process address spaces on MMUv2")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3392ef368d ]
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#address-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: pcie@2000: '#size-cells' is a required property
From schema: /lib/python3.10/site-packages/dtschema/schemas/pci/pci-bus.yaml
Two properties that need to be added later are "device_type" and
"ranges". Adding "device_type" on its own causes a new warning and the
value of "ranges" needs to be determined yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-3-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05d2c3d552 ]
Such property simply doesn't exist (is not documented or used anywhere).
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: usb@d000: Unevaluated properties are not allowed ('#usb-cells' was unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20230707114004.2740-2-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74abbfe99f ]
In accordance with the Generic EHCI/OHCI bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "generic-ehci" and "generic-ohci"-compatible
nodes are correctly named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Stable-dep-of: 05d2c3d552 ("ARM: dts: BCM53573: Drop nonexistent #usb-cells")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 822130b5e8 ]
On 32-bit architectures comparing a resource against a value larger than
U32_MAX can cause a warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1344:18: error: result of comparison of constant 4294967296 with expression of type 'resource_size_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
res->start > 0x100000000ull)
~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
As gcc does not warn about this in dead code, add an IS_ENABLED() check at
the start of the function. This will always return success but not actually resize
the BAR on 32-bit architectures without high memory, which is exactly what
we want here, as the driver can fall back to bank switching the VRAM
access.
Fixes: 31b8adab32 ("drm/amdgpu: require a root bus window above 4GB for BAR resize")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b484b1c9 ]
Since we're using these two macros to read a value from a register, we
need to use the FIELD_GET instead of the FIELD_PREP macro, otherwise
we're getting wrong values.
So instead of:
[ 3.111779] ocmem fdd00000.sram: 2 ports, 1 regions, 512 macros, not interleaved
we now get the correct value of:
[ 3.129672] ocmem fdd00000.sram: 2 ports, 1 regions, 2 macros, not interleaved
Fixes: 88c1e9404f ("soc: qcom: add OCMEM driver")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20230506-msm8226-ocmem-v3-1-79da95a2581f@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dabc8b2075 ]
The dquot_mark_dquot_dirty() using dquot references from the inode
should be protected by dquot_srcu. quota_off code takes care to call
synchronize_srcu(&dquot_srcu) to not drop dquot references while they
are used by other users. But dquot_transfer() breaks this assumption.
We call dquot_transfer() to drop the last reference of dquot and add
it to free_dquots, but there may still be other users using the dquot
at this time, as shown in the function graph below:
cpu1 cpu2
_________________|_________________
wb_do_writeback CHOWN(1)
...
ext4_da_update_reserve_space
dquot_claim_block
...
dquot_mark_dquot_dirty // try to dirty old quota
test_bit(DQ_ACTIVE_B, &dquot->dq_flags) // still ACTIVE
if (test_bit(DQ_MOD_B, &dquot->dq_flags))
// test no dirty, wait dq_list_lock
...
dquot_transfer
__dquot_transfer
dqput_all(transfer_from) // rls old dquot
dqput // last dqput
dquot_release
clear_bit(DQ_ACTIVE_B, &dquot->dq_flags)
atomic_dec(&dquot->dq_count)
put_dquot_last(dquot)
list_add_tail(&dquot->dq_free, &free_dquots)
// add the dquot to free_dquots
if (!test_and_set_bit(DQ_MOD_B, &dquot->dq_flags))
add dqi_dirty_list // add released dquot to dirty_list
This can cause various issues, such as dquot being destroyed by
dqcache_shrink_scan() after being added to free_dquots, which can trigger
a UAF in dquot_mark_dquot_dirty(); or after dquot is added to free_dquots
and then to dirty_list, it is added to free_dquots again after
dquot_writeback_dquots() is executed, which causes the free_dquots list to
be corrupted and triggers a UAF when dqcache_shrink_scan() is called for
freeing dquot twice.
As Honza said, we need to fix dquot_transfer() to follow the guarantees
dquot_srcu should provide. But calling synchronize_srcu() directly from
dquot_transfer() is too expensive (and mostly unnecessary). So we add
dquot whose last reference should be dropped to the new global dquot
list releasing_dquots, and then queue work item which would call
synchronize_srcu() and after that perform the final cleanup of all the
dquots on releasing_dquots.
Fixes: 4580b30ea8 ("quota: Do not dirty bad dquots")
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-5-libaokun1@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b9bdfa165 ]
Now we have a helper function dquot_dirty() to determine if dquot has
DQ_MOD_B bit. dquot_active() can easily be misunderstood as a helper
function to determine if dquot has DQ_ACTIVE_B bit. So we avoid this by
renaming it to inode_quota_active() and later on we will add the helper
function dquot_active() to determine if dquot has DQ_ACTIVE_B bit.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-3-libaokun1@huawei.com>
Stable-dep-of: dabc8b2075 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7248f1cc8 ]
Maximum size of buffer is obtained from underlying I2C adapter and in
case adapter allows I2C transaction buffer size greater than 100 bytes,
transaction will fail due to firmware limitation.
As a result driver will fail initialization.
Limit the maximum size of transaction buffer by 100 bytes to fit to
firmware.
Remove unnecessary calculation:
max_t(u16, MLXSW_I2C_BLK_DEF, quirk_size).
This condition can not happened.
Fixes: 3029a693be ("mlxsw: i2c: Allow flexible setting of I2C transactions size")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 146c7c3305 ]
The driver reads commands output from the output mailbox. If the size
of the output mailbox is not a multiple of the transaction /
block size, then the driver will not issue enough read transactions
to read the entire output, which can result in driver initialization
errors.
Fix by determining the number of transactions using DIV_ROUND_UP().
Fixes: 3029a693be ("mlxsw: i2c: Allow flexible setting of I2C transactions size")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 786c96e92f ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
local_irq_disable(). Compile tested only.
Fixes: 05fcd31cc4 ("arcnet: add err_skb package for package status feedback")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a05334d7f ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
spin_lock_irqsave(). Compile tested only.
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 454994cfa9 ]
If ath9k_wmi_cmd() has exited with a timeout, it is possible that during
next ath9k_wmi_cmd() call the wmi_rsp callback for previous wmi command
writes to new wmi->cmd_rsp_buf and makes a completion. This results in an
invalid ath9k_wmi_cmd() return value.
Move the replacement of WMI command response buffer and length under
wmi_lock. Note that last_seq_id value is updated there, too.
Thus, the buffer cannot be written to by a belated wmi_rsp callback
because that path is properly rejected by the last_seq_id check.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230425192607.18015-2-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b674fb513e ]
Currently, the synchronization between ath9k_wmi_cmd() and
ath9k_wmi_ctrl_rx() is exposed to a race condition which, although being
rather unlikely, can lead to invalid behaviour of ath9k_wmi_cmd().
Consider the following scenario:
CPU0 CPU1
ath9k_wmi_cmd(...)
mutex_lock(&wmi->op_mutex)
ath9k_wmi_cmd_issue(...)
wait_for_completion_timeout(...)
---
timeout
---
/* the callback is being processed
* before last_seq_id became zero
*/
ath9k_wmi_ctrl_rx(...)
spin_lock_irqsave(...)
/* wmi->last_seq_id check here
* doesn't detect timeout yet
*/
spin_unlock_irqrestore(...)
/* last_seq_id is zeroed to
* indicate there was a timeout
*/
wmi->last_seq_id = 0
mutex_unlock(&wmi->op_mutex)
return -ETIMEDOUT
ath9k_wmi_cmd(...)
mutex_lock(&wmi->op_mutex)
/* the buffer is replaced with
* another one
*/
wmi->cmd_rsp_buf = rsp_buf
wmi->cmd_rsp_len = rsp_len
ath9k_wmi_cmd_issue(...)
spin_lock_irqsave(...)
spin_unlock_irqrestore(...)
wait_for_completion_timeout(...)
/* the continuation of the
* callback left after the first
* ath9k_wmi_cmd call
*/
ath9k_wmi_rsp_callback(...)
/* copying data designated
* to already timeouted
* WMI command into an
* inappropriate wmi_cmd_buf
*/
memcpy(...)
complete(&wmi->cmd_wait)
/* awakened by the bogus callback
* => invalid return result
*/
mutex_unlock(&wmi->op_mutex)
return 0
To fix this, update last_seq_id on timeout path inside ath9k_wmi_cmd()
under the wmi_lock. Move ath9k_wmi_rsp_callback() under wmi_lock inside
ath9k_wmi_ctrl_rx() so that the wmi->cmd_wait can be completed only for
initially designated wmi_cmd call, otherwise the path would be rejected
with last_seq_id check.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230425192607.18015-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d93a7cf6ca ]
In the commit 7c4cd051ad ("bpf: Fix syscall's stackmap lookup
potential deadlock"), a potential deadlock issue was addressed, which
resulted in *_map_lookup_elem not triggering BPF programs.
(prior to lookup, bpf_disable_instrumentation() is used)
To resolve the broken map lookup probe using "htab_map_lookup_elem",
this commit introduces an alternative approach. Instead, it utilize
"bpf_map_copy_value" and apply a filter specifically for the hash table
with map_type.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Fixes: 7c4cd051ad ("bpf: Fix syscall's stackmap lookup potential deadlock")
Link: https://lore.kernel.org/r/20230818090119.477441-8-danieltimlee@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a171fbec88 ]
LWTUNNEL_XMIT_CONTINUE is implicitly assumed in ip(6)_finish_output2,
such that any positive return value from a xmit hook could cause
unexpected continue behavior, despite that related skb may have been
freed. This could be error-prone for future xmit hook ops. One of the
possible errors is to return statuses of dst_output directly.
To make the code safer, redefine LWTUNNEL_XMIT_CONTINUE value to
distinguish from dst_output statuses and check the continue
condition explicitly.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/96b939b85eda00e8df4f7c080f770970a4c5f698.1692326837.git.yan@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29b22badb7 ]
BPF encap ops can return different types of positive values, such like
NET_RX_DROP, NET_XMIT_CN, NETDEV_TX_BUSY, and so on, from function
skb_do_redirect and bpf_lwt_xmit_reroute. At the xmit hook, such return
values would be treated implicitly as LWTUNNEL_XMIT_CONTINUE in
ip(6)_finish_output2. When this happens, skbs that have been freed would
continue to the neighbor subsystem, causing use-after-free bug and
kernel crashes.
To fix the incorrect behavior, skb_do_redirect return values can be
simply discarded, the same as tc-egress behavior. On the other hand,
bpf_lwt_xmit_reroute returns useful errors to local senders, e.g. PMTU
information. Thus convert its return values to avoid the conflict with
LWTUNNEL_XMIT_CONTINUE.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: Jordan Griege <jgriege@cloudflare.com>
Suggested-by: Martin KaFai Lau <martin.lau@linux.dev>
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Yan Zhai <yan@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/0d2b878186cfe215fec6b45769c1cd0591d3628d.1692326837.git.yan@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e03dd62e5 ]
Chips such as BCM7278 support system wide suspend/resume which will
cause the HWRNG block to lose its state and reset to its power on reset
register values. We need to cleanup and re-initialize the HWRNG for it
to be functional coming out of a system suspend cycle.
Fixes: c3577f6100 ("hwrng: iproc-rng200 - Add support for BCM7278")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83a89c4b6a ]
Running the bench_rename test script, the following error occurs:
# ./benchs/run_bench_rename.sh
base : 0.819 ± 0.012M/s
kprobe : 0.538 ± 0.009M/s
kretprobe : 0.503 ± 0.004M/s
rawtp : 0.779 ± 0.020M/s
fentry : 0.726 ± 0.007M/s
fexit : 0.691 ± 0.007M/s
benchmark 'rename-fmodret' not found
The bench_rename_fmodret has been removed in commit b000def2e0
("selftests: Remove fmod_ret from test_overhead"), thus remove it
from the runners in the test script.
Fixes: b000def2e0 ("selftests: Remove fmod_ret from test_overhead")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230814030727.3010390-1-zouyipeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89688e3e9 ]
In tcp_retransmit_timer(), a window shrunk connection will be regarded
as timeout if 'tcp_jiffies32 - tp->rcv_tstamp > TCP_RTO_MAX'. This is not
right all the time.
The retransmits will become zero-window probes in tcp_retransmit_timer()
if the 'snd_wnd==0'. Therefore, the icsk->icsk_rto will come up to
TCP_RTO_MAX sooner or later.
However, the timer can be delayed and be triggered after 122877ms, not
TCP_RTO_MAX, as I tested.
Therefore, 'tcp_jiffies32 - tp->rcv_tstamp > TCP_RTO_MAX' is always true
once the RTO come up to TCP_RTO_MAX, and the socket will die.
Fix this by replacing the 'tcp_jiffies32' with '(u32)icsk->icsk_timeout',
which is exact the timestamp of the timeout.
However, "tp->rcv_tstamp" can restart from idle, then tp->rcv_tstamp
could already be a long time (minutes or hours) in the past even on the
first RTO. So we double check the timeout with the duration of the
retransmission.
Meanwhile, making "2 * TCP_RTO_MAX" as the timeout to avoid the socket
dying too soon.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/netdev/CADxym3YyMiO+zMD4zj03YPM3FBi-1LHi6gSD2XT8pyAMM096pg@mail.gmail.com/
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3673952cf0 ]
Similar to commit c5d2b6fa26 ("Bluetooth: Fix use-after-free in
hci_remove_ltk/hci_remove_irk"). We can not access k after kfree_rcu()
call.
Fixes: d7d41682ef ("Bluetooth: Fix Suspicious RCU usage warnings")
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b5aed313 ]
in nokia_bluetooth_serdev_probe(), check the return value of
clk_prepare_enable() and return the error code if
clk_prepare_enable() returns an unexpected value.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
