commit 56c1723426 upstream.
The IRQ handler bcm2835_spi_interrupt() first reads as much as possible
from the RX FIFO, then writes as much as possible to the TX FIFO.
Afterwards it decides whether the transfer is finished by checking if
the TX FIFO is empty.
If very few bytes were written to the TX FIFO, they may already have
been transmitted by the time the FIFO's emptiness is checked. As a
result, the transfer will be declared finished and the chip will be
reset without reading the corresponding received bytes from the RX FIFO.
The odds of this happening increase with a high clock frequency (such
that the TX FIFO drains quickly) and either passing "threadirqs" on the
command line or enabling CONFIG_PREEMPT_RT_BASE (such that the IRQ
handler may be preempted between filling the TX FIFO and checking its
emptiness).
Fix by instead checking whether rx_len has reached zero, which means
that the transfer has been received in full. This is also more
efficient as it avoids one bus read access per interrupt. Note that
bcm2835_spi_transfer_one_poll() likewise uses rx_len to determine
whether the transfer has finished.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: e34ff011c7 ("spi: bcm2835: move to the transfer_one driver model")
Cc: stable@vger.kernel.org # v4.1+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbc944115e upstream.
If submission of a DMA TX transfer succeeds but submission of the
corresponding RX transfer does not, the BCM2835 SPI driver terminates
the TX transfer but neglects to reset the dma_pending flag to false.
Thus, if the next transfer uses interrupt mode (because it is shorter
than BCM2835_SPI_DMA_MIN_LENGTH) and runs into a timeout,
dmaengine_terminate_all() will be called both for TX (once more) and
for RX (which was never started in the first place). Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: 3ecd37edaa ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: stable@vger.kernel.org # v4.2+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e82b0b3828 upstream.
If a DMA transfer finishes orderly right when spi_transfer_one_message()
determines that it has timed out, the callbacks bcm2835_spi_dma_done()
and bcm2835_spi_handle_err() race to call dmaengine_terminate_all(),
potentially leading to double termination.
Prevent by atomically changing the dma_pending flag before calling
dmaengine_terminate_all().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: 3ecd37edaa ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: stable@vger.kernel.org # v4.2+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18f2c4fceb upstream.
If the file system has been shut down or is read-only, then
ext4_write_inode() needs to bail out early.
Also use jbd2_complete_transaction() instead of ext4_force_commit() so
we only force a commit if it is needed.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fde872682e upstream.
Some time back, nfsd switched from calling vfs_fsync() to using a new
commit_metadata() hook in export_operations(). If the file system did
not provide a commit_metadata() hook, it fell back to using
sync_inode_metadata(). Unfortunately doesn't work on all file
systems. In particular, it doesn't work on ext4 due to how the inode
gets journalled --- the VFS writeback code will not always call
ext4_write_inode().
So we need to provide our own ext4_nfs_commit_metdata() method which
calls ext4_write_inode() directly.
Google-Bug-Id: 121195940
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a363970d1 upstream.
If we receive a file handle, either from NFS or open_by_handle_at(2),
and it points at an inode which has not been initialized, and the file
system has metadata checksums enabled, we shouldn't try to get the
inode, discover the checksum is invalid, and then declare the file
system as being inconsistent.
This can be reproduced by creating a test file system via "mke2fs -t
ext4 -O metadata_csum /tmp/foo.img 8M", mounting it, cd'ing into that
directory, and then running the following program.
#define _GNU_SOURCE
#include <fcntl.h>
struct handle {
struct file_handle fh;
unsigned char fid[MAX_HANDLE_SZ];
};
int main(int argc, char **argv)
{
struct handle h = {{8, 1 }, { 12, }};
open_by_handle_at(AT_FDCWD, &h.fh, O_RDONLY);
return 0;
}
Google-Bug-Id: 120690101
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a805622a75 upstream.
In ext4_expand_extra_isize_ea(), we calculate the total size of the
xattr header, plus the xattr entries so we know how much of the
beginning part of the xattrs to move when expanding the inode extra
size. We need to include the terminating u32 at the end of the xattr
entries, or else if there is uninitialized, non-zero bytes after the
xattr entries and before the xattr values, the list of xattr entries
won't be properly terminated.
Reported-by: Steve Graham <stgraham2000@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e647e29196 upstream.
Commit e2b911c535 ("ext4: clean up feature test macros with
predicate functions") broke the EXT4_IOC_GROUP_ADD ioctl. This was
not noticed since only very old versions of resize2fs (before
e2fsprogs 1.42) use this ioctl. However, using a new kernel with an
enterprise Linux userspace will cause attempts to use online resize to
fail with "No reserved GDT blocks".
Fixes: e2b911c535 ("ext4: clean up feature test macros with predicate...")
Cc: stable@kernel.org # v4.4
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: ruippan (潘睿) <ruippan@tencent.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 132d00becb upstream.
In case of error, ext4_try_to_write_inline_data() should unlock
and release the page it holds.
Fixes: f19d5870cb ("ext4: add normal write support for inline data")
Cc: stable@kernel.org # 3.8
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61157b24e6 upstream.
The function frees qf_inode via iput but then pass qf_inode to
lockdep_set_quota_inode on the failure path. This may result in a
use-after-free bug. The patch frees df_inode only when it is never used.
Fixes: daf647d2dd ("ext4: add lockdep annotations for i_data_sem")
Cc: stable@kernel.org # 4.6
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb265c9cb4 upstream.
Today, when sb_bread() returns NULL, this can either be because of an
I/O error or because the system failed to allocate the buffer. Since
it's an old interface, changing would require changing many call
sites.
So instead we create our own ext4_sb_bread(), which also allows us to
set the REQ_META flag.
Also fixed a problem in the xattr code where a NULL return in a
function could also mean that the xattr was not found, which could
lead to the wrong error getting returned to userspace.
Fixes: ac27a0ec11 ("ext4: initial copy of files from ext3")
Cc: stable@kernel.org # 2.6.19
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f07229f02 upstream.
The AFU Descriptor Template in the PCI config space has a Name Space
field which is a 24 Byte ASCII character string of descriptive name
space for the AFU. The OCXL driver read the string four characters at
a time with pci_read_config_dword().
This optimization is valid on a little-endian system since this is PCI,
but a big-endian system ends up with each subset of four characters in
reverse order.
This could be fixed by switching to read characters one by one. Another
option is to swap the bytes if we're big-endian.
Go for the latter with le32_to_cpu().
Cc: stable@vger.kernel.org # v4.16
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1e71e2017 upstream.
All fields in the PE are big-endian. Use cpu_to_be32() like everywhere
else something is written to the PE. Otherwise a wrong TID will be used
by the NPU. If this TID happens to point to an existing thread sharing
the same mm, it could be woken up by error. This is highly improbable
though. The likely outcome of this is the NPU not finding the target
thread and forcing the AFU into sending an interrupt, which userspace
is supposed to handle anyway.
Fixes: e948e06fc6 ("ocxl: Expose the thread_id needed for wait on POWER9")
Cc: stable@vger.kernel.org # v4.18
Signed-off-by: Greg Kurz <groug@kaod.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11a64a05dc upstream.
Depending on which functions are inlined in util/pmu.c, the snprintf()
calls in perf_pmu__parse_{scale,unit,per_pkg,snapshot}() might trigger a
warning:
util/pmu.c: In function 'pmu_aliases':
util/pmu.c:178:31: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 4095 [-Werror=format-truncation=]
snprintf(path, PATH_MAX, "%s/%s.unit", dir, name);
^~
I found this when trying to build perf from Linux 3.16 with gcc 8.
However I can reproduce the problem in mainline if I force
__perf_pmu__new_alias() to be inlined.
Suppress this by using scnprintf() as has been done elsewhere in perf.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20181111184524.fux4taownc6ndbx6@decadent.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf287607c8 upstream.
It turned out we used to use default implementation of sched_clock()
from kernel/sched/clock.c which was as precise as 1/HZ, i.e.
by default we had 10 msec granularity of time measurement.
Now given ARC built-in timers are clocked with the same frequency as
CPU cores we may get much higher precision of time tracking.
Thus we switch to generic sched_clock which really reads ARC hardware
counters.
This is especially helpful for measuring short events.
That's what we used to have:
------------------------------>8------------------------
$ perf stat /bin/sh -c /root/lmbench-master/bin/arc/hello > /dev/null
Performance counter stats for '/bin/sh -c /root/lmbench-master/bin/arc/hello':
10.000000 task-clock (msec) # 2.832 CPUs utilized
1 context-switches # 0.100 K/sec
1 cpu-migrations # 0.100 K/sec
63 page-faults # 0.006 M/sec
3049480 cycles # 0.305 GHz
1091259 instructions # 0.36 insn per cycle
256828 branches # 25.683 M/sec
27026 branch-misses # 10.52% of all branches
0.003530687 seconds time elapsed
0.000000000 seconds user
0.010000000 seconds sys
------------------------------>8------------------------
And now we'll see:
------------------------------>8------------------------
$ perf stat /bin/sh -c /root/lmbench-master/bin/arc/hello > /dev/null
Performance counter stats for '/bin/sh -c /root/lmbench-master/bin/arc/hello':
3.004322 task-clock (msec) # 0.865 CPUs utilized
1 context-switches # 0.333 K/sec
1 cpu-migrations # 0.333 K/sec
63 page-faults # 0.021 M/sec
2986734 cycles # 0.994 GHz
1087466 instructions # 0.36 insn per cycle
255209 branches # 84.947 M/sec
26002 branch-misses # 10.19% of all branches
0.003474829 seconds time elapsed
0.003519000 seconds user
0.000000000 seconds sys
------------------------------>8------------------------
Note how much more meaningful is the second output - time spent for
execution pretty much matches number of cycles spent (we're runnign
@ 1GHz here).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81b1e6e6a8 upstream.
Since the addition of platform MSI support, there were two helpers
supposed to allocate/free IRQs for a device:
platform_msi_domain_alloc_irqs()
platform_msi_domain_free_irqs()
In these helpers, IRQ descriptors are allocated in the "alloc" routine
while they are freed in the "free" one.
Later, two other helpers have been added to handle IRQ domains on top
of MSI domains:
platform_msi_domain_alloc()
platform_msi_domain_free()
Seen from the outside, the logic is pretty close with the former
helpers and people used it with the same logic as before: a
platform_msi_domain_alloc() call should be balanced with a
platform_msi_domain_free() call. While this is probably what was
intended to do, the platform_msi_domain_free() does not remove/free
the IRQ descriptor(s) created/inserted in
platform_msi_domain_alloc().
One effect of such situation is that removing a module that requested
an IRQ will let one orphaned IRQ descriptor (with an allocated MSI
entry) in the device descriptors list. Next time the module will be
inserted back, one will observe that the allocation will happen twice
in the MSI domain, one time for the remaining descriptor, one time for
the new one. It also has the side effect to quickly overshoot the
maximum number of allocated MSI and then prevent any module requesting
an interrupt in the same domain to be inserted anymore.
This situation has been met with loops of insertion/removal of the
mvpp2.ko module (requesting 15 MSIs each time).
Fixes: 552c494a76 ("platform-msi: Allow creation of a MSI-based stacked irq domain")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c987876a80 upstream.
Contrary to the non-VHE version of the TLB invalidation helpers, the VHE
code has interrupts enabled, meaning that we can take an interrupt in
the middle of such a sequence, and start running something else with
HCR_EL2.TGE cleared.
That's really not a good idea.
Take the heavy-handed option and disable interrupts in
__tlb_switch_to_guest_vhe, restoring them in __tlb_switch_to_host_vhe.
The latter also gain an ISB in order to make sure that TGE really has
taken effect.
Cc: stable@vger.kernel.org
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e814349950 upstream.
____kvm_handle_fault_on_reboot() provides a generic exception fixup
handler that is used to cleanly handle faults on VMX/SVM instructions
during reboot (or at least try to). If there isn't a reboot in
progress, ____kvm_handle_fault_on_reboot() treats any exception as
fatal to KVM and invokes kvm_spurious_fault(), which in turn generates
a BUG() to get a stack trace and die.
When it was originally added by commit 4ecac3fd6d ("KVM: Handle
virtualization instruction #UD faults during reboot"), the "call" to
kvm_spurious_fault() was handcoded as PUSH+JMP, where the PUSH'd value
is the RIP of the faulting instructing.
The PUSH+JMP trickery is necessary because the exception fixup handler
code lies outside of its associated function, e.g. right after the
function. An actual CALL from the .fixup code would show a slightly
bogus stack trace, e.g. an extra "random" function would be inserted
into the trace, as the return RIP on the stack would point to no known
function (and the unwinder will likely try to guess who owns the RIP).
Unfortunately, the JMP was replaced with a CALL when the macro was
reworked to not spin indefinitely during reboot (commit b7c4145ba2
"KVM: Don't spin on virt instruction faults during reboot"). This
causes the aforementioned behavior where a bogus function is inserted
into the stack trace, e.g. my builds like to blame free_kvm_area().
Revert the CALL back to a JMP. The changelog for commit b7c4145ba2
("KVM: Don't spin on virt instruction faults during reboot") contains
nothing that indicates the switch to CALL was deliberate. This is
backed up by the fact that the PUSH <insn RIP> was left intact.
Note that an alternative to the PUSH+JMP magic would be to JMP back
to the "real" code and CALL from there, but that would require adding
a JMP in the non-faulting path to avoid calling kvm_spurious_fault()
and would add no value, i.e. the stack trace would be the same.
Using CALL:
------------[ cut here ]------------
kernel BUG at /home/sean/go/src/kernel.org/linux/arch/x86/kvm/x86.c:356!
invalid opcode: 0000 [#1] SMP
CPU: 4 PID: 1057 Comm: qemu-system-x86 Not tainted 4.20.0-rc6+ #75
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_spurious_fault+0x5/0x10 [kvm]
Code: <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 49 89 fd 41
RSP: 0018:ffffc900004bbcc8 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffffffffff
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff888273fd8000 R08: 00000000000003e8 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000784 R12: ffffc90000371fb0
R13: 0000000000000000 R14: 000000026d763cf4 R15: ffff888273fd8000
FS: 00007f3d69691700(0000) GS:ffff888277800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f89bc56fe0 CR3: 0000000271a5a001 CR4: 0000000000362ee0
Call Trace:
free_kvm_area+0x1044/0x43ea [kvm_intel]
? vmx_vcpu_run+0x156/0x630 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0x447/0x1a40 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? __set_task_blocked+0x38/0x90
? __set_current_blocked+0x50/0x60
? __fpu__restore_sig+0x97/0x490
? do_vfs_ioctl+0xa1/0x620
? __x64_sys_futex+0x89/0x180
? ksys_ioctl+0x66/0x70
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x4f/0x100
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Modules linked in: vhost_net vhost tap kvm_intel kvm irqbypass bridge stp llc
---[ end trace 9775b14b123b1713 ]---
Using JMP:
------------[ cut here ]------------
kernel BUG at /home/sean/go/src/kernel.org/linux/arch/x86/kvm/x86.c:356!
invalid opcode: 0000 [#1] SMP
CPU: 6 PID: 1067 Comm: qemu-system-x86 Not tainted 4.20.0-rc6+ #75
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_spurious_fault+0x5/0x10 [kvm]
Code: <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 49 89 fd 41
RSP: 0018:ffffc90000497cd0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffffffffff
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88827058bd40 R08: 00000000000003e8 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000784 R12: ffffc90000369fb0
R13: 0000000000000000 R14: 00000003c8fc6642 R15: ffff88827058bd40
FS: 00007f3d7219e700(0000) GS:ffff888277900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3d64001000 CR3: 0000000271c6b004 CR4: 0000000000362ee0
Call Trace:
vmx_vcpu_run+0x156/0x630 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0x447/0x1a40 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? kvm_vcpu_ioctl+0x368/0x5c0 [kvm]
? __set_task_blocked+0x38/0x90
? __set_current_blocked+0x50/0x60
? __fpu__restore_sig+0x97/0x490
? do_vfs_ioctl+0xa1/0x620
? __x64_sys_futex+0x89/0x180
? ksys_ioctl+0x66/0x70
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x4f/0x100
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Modules linked in: vhost_net vhost tap kvm_intel kvm irqbypass bridge stp llc
---[ end trace f9daedb85ab3ddba ]---
Fixes: b7c4145ba2 ("KVM: Don't spin on virt instruction faults during reboot")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b5e4d623e upstream.
Swap storage is restricted to max_swapfile_size (~16TB on x86_64) whenever
the system is deemed affected by L1TF vulnerability. Even though the limit
is quite high for most deployments it seems to be too restrictive for
deployments which are willing to live with the mitigation disabled.
We have a customer to deploy 8x 6,4TB PCIe/NVMe SSD swap devices which is
clearly out of the limit.
Drop the swap restriction when l1tf=off is specified. It also doesn't make
much sense to warn about too much memory for the l1tf mitigation when it is
forcefully disabled by the administrator.
[ tglx: Folded the documentation delta change ]
Fixes: 377eeaa8e1 ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: <linux-mm@kvack.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181113184910.26697-1-mhocko@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e3c336ad8 upstream.
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98dfd32620 upstream.
When triggered by pci hotplug (PEC 0x306) clp_get_state is called
with spinlocks held resulting in the following warning:
zpci: n/a: Event 0x306 reconfigured PCI function 0x0
BUG: sleeping function called from invalid context at mm/page_alloc.c:4324
in_atomic(): 1, irqs_disabled(): 0, pid: 98, name: kmcheck
2 locks held by kmcheck/98:
Change the allocation to use GFP_ATOMIC.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ea56cff5 upstream.
The Gnawty model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Clapper and Swanky models.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Gnawty that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201787
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Jaime Pérez <19.jaime.91@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 984bfb398a upstream.
The Clapper model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Swanky model.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Clapper that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c58eef061d upstream.
Currently the cmd.read_write setting is not initialized so it contains
garbage from the stack. Fix this by setting it to 0 to indicate a
read is required.
Detected by CoverityScan, CID#1357925 ("Uninitialized scalar variable")
Fixes: c5c77ba18e ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 255095fa7f upstream.
commit 1a0c10ed7b ("media: dvb-usb-v2: stop using coherent memory for
URBs") incorrectly adds URB_FREE_BUFFER after every urb transfer.
It cannot use this flag because it reconfigures the URBs accordingly
to suit connected devices. In doing a call to usb_free_urb is made and
invertedly frees the buffers.
The stream buffer should remain constant while driver is up.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
CC: stable@vger.kernel.org # v4.18+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3788cd996 upstream.
That makes the USB role switch support option visible and
selectable for the user. The class driver is also moved to
drivers/usb/roles/ directory.
This will fix an issue that we have with the Intel USB role
switch driver on systems that don't have USB Type-C connectors:
Intel USB role switch driver depends on the USB role switch
class as it should, but since there was no way for the user
to enable the USB role switch class, there was also no way
to select that driver. USB Type-C drivers select the USB
role switch class which makes the Intel USB role switch
driver available and therefore hides the problem.
So in practice Intel USB role switch driver was depending on
USB Type-C drivers.
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3004cfd620 upstream.
Commit 211f658b7b ("usb: dwc3: pci: Use devm functions to get
the phy GPIOs") changed the code to claim the PHY GPIOs permanently
for Intel Baytrail devices.
This causes issues when the actual PHY driver attempts to claim the
same GPIO descriptors. For example, tusb1210 now fails to probe with:
tusb1210: probe of dwc3.0.auto.ulpi failed with error -16 (EBUSY)
dwc3-pci needs to turn on the PHY once before dwc3 is loaded, but
usually the PHY driver will then hold the GPIOs to turn off the
PHY when requested (e.g. during suspend).
To fix the problem, this reverts the commit to restore the old
behavior to put the GPIOs immediately after usage.
Link: https://www.spinics.net/lists/linux-usb/msg174681.html
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc10ce0c51 upstream.
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).
A similar fix was implemented for Rockchip SoCs in commit c216765d3a
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").
Cc: <stable@vger.kernel.org> # 4.19
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c85400f886 upstream.
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ed30a7d8e upstream.
Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.
A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.
This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.
Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).
<idle>-0 [000] ..s. 1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
<idle>-0 [000] ..s. 1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977
After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.
<idle>-0 [000] d.h. 1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
<idle>-0 [000] d.h. 1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002
The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Terin Stock <terin@terinstock.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63d2a9ec31 upstream.
Even after disabling interrupts on the module, it could be possible
that irq handlers are still running. System hang is seen during
suspend path. It was found that, there were pending writes on the
HDA bus and clock was disabled by that time.
Above mentioned issue is fixed by clearing any pending irq handlers
before disabling clocks and returning from hda suspend.
Suggested-by: Mohan Kumar <mkumard@nvidia.com>
Suggested-by: Dara Ramesh <dramesh@nvidia.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82b01149ec upstream.
The headset mic of ASUS laptops like UX533FD, UX433FN and UX333FA, whose
CODEC is Realtek ALC294 has jack auto detection feature. This patch
enables the feature.
Fixes: 4e05110673 ("ALSA: hda/realtek: Enable audio jacks of ASUS UX533FD with ALC294")
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ef108c53e upstream.
An initial commit to add tracepoints for packets without CIP headers
uses different print formats for added tracepoints. However this is not
convenient for users/developers to prepare debug tools.
This commit uses the same format for the two tracepoints.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: b164d2fd6e ('ALSA: firewire_lib: add tracepoints for packets without CIP headers')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa9a9e39b4 upstream.
An initial commit to add tracepoints for packets without CIP headers
introduces a wrong assignment to 'data_blocks' value of
'out_packet_without_header' tracepoint.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: b164d2fd6e ('ALSA: firewire_lib: add tracepoints for packets without CIP headers')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ada79fa5a0 upstream.
In IEC 61883-1/6 engine of ALSA firewire stack, a packet handler has a
second argument for 'the number of bytes in payload of isochronous
packet'. However, an incoming packet handler without CIP header uses the
value as 'the number of quadlets in the payload'. This brings userspace
applications to receive the number of PCM frames as four times against
real time.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 3b196c394d ('ALSA: firewire-lib: add no-header packet processing')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d16200a3e upstream.
According to my memo at hand and saved records, writing 0x00000001 to
SND_FF_REG_FETCH_PCM_FRAMES disables fetching PCM frames in corresponding
channel, however current implement uses reversed logic. This results in
muted volume in device side during playback.
This commit corrects the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 76fdb3a9e1 ('ALSA: fireface: add support for Fireface 400')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
