[ Upstream commit 5ab99cf7d5 ]
The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused. However they supply critical parts of
SoC so they should be always on:
1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
VDDQ_GPIO (gpm7, gpy7).
The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
marking it "always-on" only reflects its real status.
2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
memory and Mali (G3D).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b00ef53053 ]
It must be made sure that immediate mode is not already set, when
modifying shadow register value in ehrpwm_pwm_disable(). Otherwise
modifications to the action-qualifier continuous S/W force
register(AQSFRC) will be done in the active register.
This may happen when both channels are being disabled. In this case,
only the first channel state will be recorded as disabled in the shadow
register. Later, when enabling the first channel again, the second
channel would be enabled as well. Setting RLDCSF to zero, first, ensures
that the shadow register is updated as desired.
Fixes: 38dabd91ff ("pwm: tiehrpwm: Fix disabling of output of PWMs")
Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
[vigneshr@ti.com: Improve commit message]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ba846b1ee ]
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 203a068ac9 ]
Currently we aren't checking for the ICE_FC_NONE case for the current
flow control mode. This is causing "Unknown" to be printed for the
current flow control method if flow control is disabled. Fix this by
adding the case for ICE_FC_NONE to print "None".
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 778c02a236 ]
If a sync bfq_queue has a higher weight than some other queue, and
remains temporarily empty while in service, then, to preserve the
bandwidth share of the queue, it is necessary to plug I/O dispatching
until a new request arrives for the queue. In addition, a timeout
needs to be set, to avoid waiting for ever if the process associated
with the queue has actually finished its I/O.
Even with the above timeout, the device is however not fed with new
I/O for a while, if the process has finished its I/O. If this happens
often, then throughput drops and latencies grow. For this reason, the
timeout is kept rather low: 8 ms is the current default.
Unfortunately, such a low value may cause, on the opposite end, a
violation of bandwidth guarantees for a process that happens to issue
new I/O too late. The higher the system load, the higher the
probability that this happens to some process. This is a problem in
scenarios where service guarantees matter more than throughput. One
important case are weight-raised queues, which need to be granted a
very high fraction of the bandwidth.
To address this issue, this commit lower-bounds the plugging timeout
for weight-raised queues to 20 ms. This simple change provides
relevant benefits. For example, on a PLEXTOR PX-256M5S, with which
gnome-terminal starts in 0.6 seconds if there is no other I/O in
progress, the same applications starts in
- 0.8 seconds, instead of 1.2 seconds, if ten files are being read
sequentially in parallel
- 1 second, instead of 2 seconds, if, in parallel, five files are
being read sequentially, and five more files are being written
sequentially
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec7f6aad57 ]
When ioremap fails, hga_vram should not be dereferenced. The fix
check the failure to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: Ferenc Bakonyi <fero@drama.obuda.kando.hu>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0257eda08e ]
Driver maintains state machine for processing and completing switch
commands. This patch resets FCF_ASYNC_{SENT|ACTIVE} flag to indicate if the
previous command is active or sent, in order for next GPSC command to
advance the state machine.
[mkp: commit desc typo]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 954b4b752a ]
The MSI message address in the RC address space can be 64 bit. The
R-Car PCIe RC supports such a 64bit MSI message address as well.
The code currently uses virt_to_phys(__get_free_pages()) to obtain
a reserved page for the MSI message address, and the return value
of which can be a 64 bit physical address on 64 bit system.
However, the driver only programs PCIEMSIALR register with the bottom
32 bits of the virt_to_phys(__get_free_pages()) return value and does
not program the top 32 bits into PCIEMSIAUR, but rather programs the
PCIEMSIAUR register with 0x0. This worked fine on older 32 bit R-Car
SoCs, however may fail on new 64 bit R-Car SoCs.
Since from a PCIe controller perspective, an inbound MSI is a memory
write to a special address (in case of this controller, defined by
the value in PCIEMSIAUR:PCIEMSIALR), which triggers an interrupt, but
never hits the DRAM _and_ because allocation of an MSI by a PCIe card
driver obtains the MSI message address by reading PCIEMSIAUR:PCIEMSIALR
in rcar_msi_setup_irqs(), incorrectly programmed PCIEMSIAUR cannot
cause memory corruption or other issues.
There is however the possibility that if virt_to_phys(__get_free_pages())
returned address above the 32bit boundary _and_ PCIEMSIAUR was programmed
to 0x0 _and_ if the system had physical RAM at the address matching the
value of PCIEMSIALR, a PCIe card driver could allocate a buffer with a
physical address matching the value of PCIEMSIALR and a remote write to
such a buffer by a PCIe card would trigger a spurious MSI.
Fixes: e015f88c36 ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72110b5674 ]
When set 2 same MAC to different function of one port, IMP
will return error as the later one may modify the origin one.
This will cause bond fail for 2 VFs of one port.
Driver just print warning and return 0 with this patch, so
if set same MAC address, it will return 0 but do not really
configure HW.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cd0e49711 ]
Call order on probe():
- max14656_hw_init() enables interrupts on the chip
- devm_request_irq() starts processing interrupts, isr
could be called immediately
- isr: schedules delayed work (irq_work)
- irq_work: calls power_supply_changed()
- devm_power_supply_register() registers the power supply
Depending on timing, it's possible that power_supply_changed()
is called on an unregistered power supply structure.
Fix by registering the power supply before requesting the irq.
Cc: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72aff4ecf1 ]
This area is used to store keys by HSPPA in case of AM438x SOC. Leave it
active.
Signed-off-by: Kabir Sahane <x0153567@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1e07ba89d ]
[Why]
The input color space for the plane was previously ignored even if it
was set.
If a limited range YUV format was given to DC then the
wrong color transformation matrix was being used since DC assumed that
it was full range instead.
[How]
Respect the given color_space format for the plane if it isn't
COLOR_SPACE_UNKNOWN. Otherwise, use the implicit default since DM
didn't specify.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb26228bfc ]
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbdc00a7de ]
The rk3288 SoC has two PWM implementations available, the "old"
implementation and the "new" one. You can switch between the two of
them by flipping a bit in the grf.
The "old" implementation is the default at chip power up but isn't the
one that's officially supposed to be used. ...and, in fact, the
driver that gets selected in Linux using the rk3288 device tree only
supports the "new" implementation.
Long ago I tried to get a switch to the right IP block landed in the
PWM driver (search for "rk3288: Switch to use the proper PWM IP") but
that got rejected. In the mean time the grf has grown a full-fledged
driver that already sets other random bits like this. That means we
can now get the fix landed.
For those wondering how things could have possibly worked for the last
4.5 years, folks have mostly been relying on the bootloader to set
this bit. ...but occasionally folks have pointed back to my old patch
series [1] in downstream kernels.
[1] https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1391597.html
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57a20248ef ]
Experimentally it can be seen that going into deep sleep (specifically
setting PMU_CLR_DMA and PMU_CLR_BUS in RK3288_PMU_PWRMODE_CON1)
appears to fail unless "aclk_dmac1" is on. The failure is that the
system never signals that it made it into suspend on the GLOBAL_PWROFF
pin and it just hangs.
NOTE that it's confirmed that it's the actual suspend that fails, not
one of the earlier calls to read/write registers. Specifically if you
comment out the "PMU_GLOBAL_INT_DISABLE" setting in
rk3288_slp_mode_set() and then comment out the "cpu_do_idle()" call in
rockchip_lpmode_enter() then you can exercise the whole suspend path
without any crashing.
This is currently not a problem with suspend upstream because there is
no current way to exercise the deep suspend code. However, anyone
trying to make it work will run into this issue.
This was not a problem on shipping rk3288-based Chromebooks because
those devices all ran on an old kernel based on 3.14. On that kernel
"aclk_dmac1" appears to be left on all the time.
There are several ways to skin this problem.
A) We could add "aclk_dmac1" to the list of critical clocks and that
apperas to work, but presumably that wastes power.
B) We could keep a list of "struct clk" objects to enable at suspend
time in clk-rk3288.c and use the standard clock APIs.
C) We could make the rk3288-pmu driver keep a list of clocks to enable
at suspend time. Presumably this would require a dts and bindings
change.
D) We could just whack the clock on in the existing syscore suspend
function where we whack a bunch of other clocks. This is particularly
easy because we know for sure that the clock's only parent
("aclk_cpu") is a critical clock so we don't need to do anything more
than ungate it.
In this case I have chosen D) because it seemed like the least work,
but any of the other options would presumably also work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89e28da828 ]
When building with -Wsometimes-uninitialized, Clang warns:
drivers/soc/mediatek/mtk-pmic-wrap.c:1358:6: error: variable 'rdata' is
used uninitialized whenever '||' condition is true
[-Werror,-Wsometimes-uninitialized]
If pwrap_write returns non-zero, pwrap_read will not be called to
initialize rdata, meaning that we will use some random uninitialized
stack value in our print statement. Zero initialize rdata in case this
happens.
Link: https://github.com/ClangBuiltLinux/linux/issues/401
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f316a2b53c ]
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94d4e7af14 ]
As new transfer mechanisms are added to the EC codebase, they may
not support v2 of the EC protocol.
If the v3 initial handshake transfer fails, the kernel will try
and call cmd_xfer as a fallback. If v2 is not supported, cmd_xfer
will be NULL, and the code will end up causing a kernel panic.
Add a check for NULL before calling the transfer function, along
with a helpful comment explaining how one might end up in this
situation.
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e957b377b ]
Added a new local variable in the i40e_setup_tc function named
old_queue_pairs so num_queue_pairs can be restored to the correct
value in case configuring queue channels fails. Additionally, moved
the exit label in the i40e_setup_tc function so the if (need_reset)
block can be executed.
Also, fixed data packing in the i40e_setup_tc function.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea094d5358 ]
In pcibios_irq_init(), the PCI IRQ routing table 'pirq_table' is first
found through pirq_find_routing_table(). If the table is not found and
CONFIG_PCI_BIOS is defined, the table is then allocated in
pcibios_get_irq_routing_table() using kmalloc(). Later, if the I/O APIC is
used, this table is actually not used. In that case, the allocated table
is not freed, which is a memory leak.
Free the allocated table if it is not used.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
[bhelgaas: added Ingo's reviewed-by, since the only change since v1 was to
use the irq_routing_table local variable name he suggested]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9872760eb7 ]
The XDomain protocol messages may start as soon as Thunderbolt control
channel is started. This means that if the other host starts sending
ThunderboltIP packets early enough they will be passed to the network
driver which then gets confused because its resume hook is not called
yet.
Fix this by unregistering the ThunderboltIP protocol handler when
suspending and registering it back on resume.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 083c1b5e50 ]
When running application tool switchtec-user's `firmware update` and `event
wait` commands concurrently, sometimes the firmware update speed reduced
significantly.
It is because when the MRPC event happened after MRPC event occurrence
check but before the event mask loop reaches its header register in event
ISR, the MRPC event would be masked unintentionally. Since there's no
chance to enable it again except for a module reload, all the following
MRPC execution completion checks time out.
Fix this bug by skipping the mask operation for MRPC event in event ISR,
same as what we already do for LINK event.
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f54c447df ]
Disabling the SMMU when probing from within a kdump kernel so that all
incoming transactions are terminated can prevent the core of the crashed
kernel from being transferred off the machine if all I/O devices are
behind the SMMU.
Instead, continue to probe the SMMU after it is disabled so that we can
reinitialise it entirely and re-attach the DMA masters as they are reset.
Since the kdump kernel may not have drivers for all of the active DMA
masters, we suppress fault reporting to avoid spamming the console and
swamping the IRQ threads.
Reported-by: "Leizhen (ThunderTown)" <thunder.leizhen@huawei.com>
Tested-by: "Leizhen (ThunderTown)" <thunder.leizhen@huawei.com>
Tested-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41be3e2618 ]
vfio_dev_present() which is the condition to
wait_event_interruptible_timeout(), will call vfio_group_get_device
and try to acquire the mutex group->device_lock.
wait_event_interruptible_timeout() will set the state of the current
task to TASK_INTERRUPTIBLE, before doing the condition check. This
means that we will try to acquire the mutex while already in a
sleeping state. The scheduler warns us by giving the following
warning:
[ 4050.264464] ------------[ cut here ]------------
[ 4050.264508] do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000b33c00e2>] prepare_to_wait_event+0x14a/0x188
[ 4050.264529] WARNING: CPU: 12 PID: 35924 at kernel/sched/core.c:6112 __might_sleep+0x76/0x90
....
4050.264756] Call Trace:
[ 4050.264765] ([<000000000017bbaa>] __might_sleep+0x72/0x90)
[ 4050.264774] [<0000000000b97edc>] __mutex_lock+0x44/0x8c0
[ 4050.264782] [<0000000000b9878a>] mutex_lock_nested+0x32/0x40
[ 4050.264793] [<000003ff800d7abe>] vfio_group_get_device+0x36/0xa8 [vfio]
[ 4050.264803] [<000003ff800d87c0>] vfio_del_group_dev+0x238/0x378 [vfio]
[ 4050.264813] [<000003ff8015f67c>] mdev_remove+0x3c/0x68 [mdev]
[ 4050.264825] [<00000000008e01b0>] device_release_driver_internal+0x168/0x268
[ 4050.264834] [<00000000008de692>] bus_remove_device+0x162/0x190
[ 4050.264843] [<00000000008daf42>] device_del+0x1e2/0x368
[ 4050.264851] [<00000000008db12c>] device_unregister+0x64/0x88
[ 4050.264862] [<000003ff8015ed84>] mdev_device_remove+0xec/0x130 [mdev]
[ 4050.264872] [<000003ff8015f074>] remove_store+0x6c/0xa8 [mdev]
[ 4050.264881] [<000000000046f494>] kernfs_fop_write+0x14c/0x1f8
[ 4050.264890] [<00000000003c1530>] __vfs_write+0x38/0x1a8
[ 4050.264899] [<00000000003c187c>] vfs_write+0xb4/0x198
[ 4050.264908] [<00000000003c1af2>] ksys_write+0x5a/0xb0
[ 4050.264916] [<0000000000b9e270>] system_call+0xdc/0x2d8
[ 4050.264925] 4 locks held by sh/35924:
[ 4050.264933] #0: 000000001ef90325 (sb_writers#4){.+.+}, at: vfs_write+0x9e/0x198
[ 4050.264948] #1: 000000005c1ab0b3 (&of->mutex){+.+.}, at: kernfs_fop_write+0x1cc/0x1f8
[ 4050.264963] #2: 0000000034831ab8 (kn->count#297){++++}, at: kernfs_remove_self+0x12e/0x150
[ 4050.264979] #3: 00000000e152484f (&dev->mutex){....}, at: device_release_driver_internal+0x5c/0x268
[ 4050.264993] Last Breaking-Event-Address:
[ 4050.265002] [<000000000017bbaa>] __might_sleep+0x72/0x90
[ 4050.265010] irq event stamp: 7039
[ 4050.265020] hardirqs last enabled at (7047): [<00000000001cee7a>] console_unlock+0x6d2/0x740
[ 4050.265029] hardirqs last disabled at (7054): [<00000000001ce87e>] console_unlock+0xd6/0x740
[ 4050.265040] softirqs last enabled at (6416): [<0000000000b8fe26>] __udelay+0xb6/0x100
[ 4050.265049] softirqs last disabled at (6415): [<0000000000b8fe06>] __udelay+0x96/0x100
[ 4050.265057] ---[ end trace d04a07d39d99a9f9 ]---
Let's fix this as described in the article
https://lwn.net/Articles/628628/.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
[remove now redundant vfio_dev_present()]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ab88ca4bc ]
clang warns that 'contextlen' may be accessed without an initialization:
fs/nfsd/nfs4xdr.c:2911:9: error: variable 'contextlen' is uninitialized when used here [-Werror,-Wuninitialized]
contextlen);
^~~~~~~~~~
fs/nfsd/nfs4xdr.c:2424:16: note: initialize the variable 'contextlen' to silence this warning
int contextlen;
^
= 0
Presumably this cannot happen, as FATTR4_WORD2_SECURITY_LABEL is
set if CONFIG_NFSD_V4_SECURITY_LABEL is enabled.
Adding another #ifdef like the other two in this function
avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b8f62625d ]
A fuzzer recently triggered lockdep warnings about potential sb_writers
deadlocks caused by fh_want_write().
Looks like we aren't careful to pair each fh_want_write() with an
fh_drop_write().
It's not normally a problem since fh_put() will call fh_drop_write() for
us. And was OK for NFSv3 where we'd do one operation that might call
fh_want_write(), and then put the filehandle.
But an NFSv4 protocol fuzzer can do weird things like call unlink twice
in a compound, and then we get into trouble.
I'm a little worried about this approach of just leaving everything to
fh_put(). But I think there are probably a lot of
fh_want_write()/fh_drop_write() imbalances so for now I think we need it
to be more forgiving.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7640682e67 ]
FUSE filesystem server and kernel client negotiate during initialization
phase, what should be the maximum write size the client will ever issue.
Correspondingly the filesystem server then queues sys_read calls to read
requests with buffer capacity large enough to carry request header + that
max_write bytes. A filesystem server is free to set its max_write in
anywhere in the range between [1*page, fc->max_pages*page]. In particular
go-fuse[2] sets max_write by default as 64K, wheres default fc->max_pages
corresponds to 128K. Libfuse also allows users to configure max_write, but
by default presets it to possible maximum.
If max_write is < fc->max_pages*page, and in NOTIFY_RETRIEVE handler we
allow to retrieve more than max_write bytes, corresponding prepared
NOTIFY_REPLY will be thrown away by fuse_dev_do_read, because the
filesystem server, in full correspondence with server/client contract, will
be only queuing sys_read with ~max_write buffer capacity, and
fuse_dev_do_read throws away requests that cannot fit into server request
buffer. In turn the filesystem server could get stuck waiting indefinitely
for NOTIFY_REPLY since NOTIFY_RETRIEVE handler returned OK which is
understood by clients as that NOTIFY_REPLY was queued and will be sent
back.
Cap requested size to negotiate max_write to avoid the problem. This
aligns with the way NOTIFY_RETRIEVE handler works, which already
unconditionally caps requested retrieve size to fuse_conn->max_pages. This
way it should not hurt NOTIFY_RETRIEVE semantic if we return less data than
was originally requested.
Please see [1] for context where the problem of stuck filesystem was hit
for real, how the situation was traced and for more involving patch that
did not make it into the tree.
[1] https://marc.info/?l=linux-fsdevel&m=155057023600853&w=2
[2] https://github.com/hanwen/go-fuse
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Cc: Jakob Unterwurzacher <jakobunt@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da75b89097 ]
The device tree binding already lists compatible strings for these two
SoCs. They don't have the defect as seen on the H3, and the size and
register layout is the same as the A64. Furthermore, the driver does
not include nvmem cell definitions.
Add support for these two compatible strings, re-using the config for
the A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fe518fecb ]
When the bit_offset in the cell is zero, the pointer to the msb will
not be properly initialized (ie, will still be pointing to the first
byte in the buffer).
This being the case, if there are bits to clear in the msb, those will
be left untouched while the mask will incorrectly clear bit positions
on the first byte.
This commit also makes sure that any byte unused in the cell is
cleared.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f495222e28 ]
Currently the IRQ handler in HD-audio controller driver is registered
before the chip initialization. That is, we have some window opened
between the azx_acquire_irq() call and the CORB/RIRB setup. If an
interrupt is triggered in this small window, the IRQ handler may
access to the uninitialized RIRB buffer, which leads to a NULL
dereference Oops.
This is usually no big problem since most of Intel chips do register
the IRQ via MSI, and we've already fixed the order of the IRQ
enablement and the CORB/RIRB setup in the former commit b61749a89f
("sound: enable interrupt after dma buffer initialization"), hence the
IRQ won't be triggered in that room. However, some platforms use a
shared IRQ, and this may allow the IRQ trigger by another source.
Another possibility is the kdump environment: a stale interrupt might
be present in there, the IRQ handler can be falsely triggered as well.
For covering this small race, let's move the azx_acquire_irq() call
after hda_intel_init_chip() call. Although this is a bit radical
change, it can cover more widely than checking the CORB/RIRB setup
locally in the callee side.
Reported-by: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a302afbe ]
flow_offload_alloc() calls nf_route() to get a dst_entry. Internally,
nf_route() calls ip_route_output_key() that allocates a dst_entry and
holds it. So, a dst_entry should be released by dst_release() if
nf_route() is successful.
Otherwise, netns exit routine cannot be finished and the following
message is printed:
[ 257.490952] unregister_netdevice: waiting for lo to become free. Usage count = 1
Fixes: ac2a66665e ("netfilter: add generic flow table infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33cc3c0cfa ]
nf_flow_offload_ip_hook() and nf_flow_offload_ipv6_hook() do not check
ttl value. So, ttl value overflow may occur.
Fixes: 97add9f0d6 ("netfilter: flow table support for IPv4")
Fixes: 0995210753 ("netfilter: flow table support for IPv6")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dc1a38ef1 ]
We do not restart a controller in a deleting state for timeout errors.
When in this state, unblock potential request dispatchers with failed
completions by shutting down the controller on timeout detection.
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8e9e9b764 ]
Just like IO queues, the admin queue also will not be restarted after a
controller shutdown. Unquiesce this queue so that we do not block
request dispatch on a permanently disabled controller.
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b7330303a ]
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
