create_bulk_endpoints should not be __init since it is called when
accessory is enabled
Change-Id: If827a4531f0f6c15af938345163923186368e2a5
Signed-off-by: Benoit Goby <benoit@android.com>
Add support for FunctionFS (ffs) to implement usb functions in userspace.
The aliases property stores the list of functions that are implemented
using functionfs.
For example:
echo "adb,mtp" > /sys/class/android_usb/android0/f_ffs/aliases
Then when the function are enabled:
echo "adb,acm" > /sys/class/android_usb/android0/functions
Internally, ffs and acm will be used.
Change-Id: I44117b183d48a5a99ddbee3ef2cf8998be74598e
Signed-off-by: Benoit Goby <benoit@android.com>
Product names may contain spaces and scanf %s only matches the 1st word.
Use strlcpy instead.
Change-Id: Ie8703fea9775f7fc17fe615a42597ca3816d36b0
Signed-off-by: Benoit Goby <benoit@android.com>
Remove the config from the configs list before releasing the spinlock.
Otherwise the other cpu might be processing a SET_CONFIGURATION that
will switch to the configuration that is being released.
Change-Id: Id4da0d0e18ead63e20cb236cd1d3e8e6d116acce
Signed-off-by: Benoit Goby <benoit@android.com>
On non-developer devices kgdb prevents CONFIG_PANIC_TIMEOUT from
rebooting the device after a panic. Add module parameters
debug_core.break_on_exception and debug_core.break_on_panic to
allow skipping debug on panics and exceptions respectively. Both
default to true to preserve existing behavior.
Change-Id: I75dce7263e96cee069a9750920cce83dc6f98e8c
Signed-off-by: Colin Cross <ccross@android.com>
Adds a new trace event to be called from clk_set_parent. Some
cpufreq drivers, including Tegra, reparent the cpu clock to a
slower clock while the main pll is relocking, tracing
clk_set_parent allows traces to show how for long the cpu is
running slower.
Uses a separate TRACE_EVENT instead of the clock event class to
allow the event to contain string names for the child and the
parent.
Signed-off-by: Colin Cross <ccross@android.com>
qtaguid tracks the device stats by monitoring when it goes up and down,
then it gets the dev_stats().
But devs don't correctly report stats (either they don't count headers
symmetrically between rx/tx, or they count internal control messages).
Now qtaguid counts the rx/tx bytes/packets during raw:prerouting and
mangle:postrouting (nat is not available in ipv6).
The results are in
/proc/net/xt_qtaguid/iface_stat_fmt
which outputs a format line (bash expansion):
ifname total_skb_{rx,tx}_{bytes,packets}
Added event counters for pre/post handling.
Added extra ctrl_*() pid/uid debugging.
Change-Id: Id84345d544ad1dd5f63e3842cab229e71d339297
Signed-off-by: JP Abgrall <jpa@google.com>
Send notifications when the label becomes active after an idle period.
Send netlink message notifications in addition to sysfs notifications.
Using a uevent with
subsystem=xt_idletimer
INTERFACE=...
STATE={active,inactive}
This is backport from common android-3.0
commit: beb914e987
with uevent support instead of a new netlink message type.
Change-Id: I31677ef00c94b5f82c8457e5bf9e5e584c23c523
Signed-off-by: Ashish Sharma <ashishsharma@google.com>
Signed-off-by: JP Abgrall <jpa@google.com>
This is required to pass the headers_check
Change-Id: Ic4c773973278cbdf1cb4eb66473826cb96ccbfb3
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Commit b641072 ("security: Add AID_NET_RAW and AID_NET_ADMIN capability
check in cap_capable().") introduces additional checks for AID_NET_xxx
macros. Since the header file including those macros are conditionally
included, the checks should also be conditionally executed.
Change-Id: Iaec5208d5b95a46b1ac3f2db8449c661e803fa5b
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Allow speed to drop to flooor frequency but not below, don't pin
to speed at last boost.
Change-Id: I0147c2b7a2e61ba16820605af6baaf09570be787
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Allow speed drop after min_sample_time elapses from last time
the current speed was last re-validated as appropriate for
current load / input boost.
Allow speed bump after min_sample_time (or above_hispeed_delay)
elapses from the time the current speed was originally set.
Change-Id: Ic25687a7a53d25e6544c30c47d7ab6f27a47bee8
Signed-off-by: Todd Poynor <toddpoynor@google.com>
For systems that set a common speed for all CPUs, checking current
speed here could bypass the intermediate hispeed bump decision for
this CPU when another CPU was already at hispeed. This could
result in an overly high setting (for all CPUs) in situations
where all CPUs were about to drop to load levels that map to
hispeed or below.
Change-Id: I186f23dcfc5e2b6336cab8b0327f0c8a9a4482bc
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Apply min_sample_time to the last time the current target speed
was originally requested or re-validated as appropriate for the
current load, not to the time since the current speed was
originally set. Avoids periodic dips in speed during bursty
loads.
Change-Id: I250bda657985de60373f9897cc41f480664d51a1
Signed-off-by: Todd Poynor <toddpoynor@google.com>
If load is above go_hispeed_load, always go to at least hispeed_freq,
even when reducing speed from a higher speed, not just when jumping
up from minimum speed. Avoids running at a lower than intended
speed after a burst of even higher load.
Change-Id: I5b9d2a15ba25ce609b21bac7c724265cf6838dee
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Evaluate spikes in load (below go_hispeed_load) against the maximum
speed supported by the device, not the current speed (which tends to
make it too difficult to raise speed to intermediate levels until
very busy).
Change-Id: Ib937006abf8bedb60891a739acd733e89b732ae0
Signed-off-by: Todd Poynor <toddpoynor@google.com>
When updating the stats for a given uid it would incorrectly assume
IPV4 and pick up the wrong protocol when IPV6.
Change-Id: Iea4a635012b4123bf7aa93809011b7b2040bb3d5
Signed-off-by: JP Abgrall <jpa@google.com>
There was a case that might have seemed like new_tag_stat was not
initialized and actually used.
Added comment explaining why it was impossible, and a BUG()
in case the logic gets changed.
Change-Id: I1eddd1b6f754c08a3bf89f7e9427e5dce1dfb081
Signed-off-by: JP Abgrall <jpa@google.com>
When PowerDown was requested at the same time as ProgBit, the
formatter flush command that follows could get stuck.
Change-Id: Iafb665f61f055819e64ca1dcb60398c656f593e4
Signed-off-by: Arve Hjønnevåg <arve@android.com>
When adb is enabled, only connect the gadget when adbd is ready. If adbd
dies or is restarted (e.g. "adb root"), the gadget is disconnected when
the adb device is close, and it is re-connected once adb re-open the
device.
- Add callbacks to adb, similar to FunctionFs callbacks, to notify the
gadget when the daemon is ready or closed.
- Refcount calls to android_enable/android_disable to enable the gadget
only once all the function daemons are ready.
- Add enable/disble to android_usb_function to notify the function when
it is added/removed from the list of enabled functions.
Change-Id: Id54ff85aec9cf8715c94b4f9bd6137a79ad58bfc
Signed-off-by: Benoit Goby <benoit@android.com>
Fix setting up consoles on multiple fiq debugger devices by
splitting the tty driver init into the initcall, and initializing
the single tty device during probe. Has the side effect of moving
the tty device node to /dev/ttyFIQx, where x is the platform device
id, which should normally match the serial port.
To avoid having to pass a different console=/dev/ttyFIQx for every
device, make the fiq debugger a preferred console that will be used
by default if no console was passed on the command line.
Change-Id: I6cc2670628a41e84615859bc96adba189966d647
Signed-off-by: Colin Cross <ccross@android.com>
kdb expects carriage returns through the serial port to terminate
commands. Modify it to accept the first seen carriage return or
new line as a terminator, but not treat \r\n as two terminators.
Change-Id: I06166017e7703d24310eefcb71c3a7d427088db7
Signed-off-by: Colin Cross <ccross@android.com>
Adds polling tty ops to the fiq debugger console tty, which allows
kgdb to run against an fiq debugger console.
Add a check in do_sysrq to prevent enabling kgdb from the fiq
debugger unless a flag (writable only by root) has been set. This
should make it safe to enable KGDB on a production device.
Also add a shortcut to enable the console and kgdb together, to
allow kgdb to be enabled when the shell on the console is not
responding.
Change-Id: Ifc65239ca96c9887431a6a36b9b44a539002f544
Signed-off-by: Colin Cross <ccross@android.com>
Convert all the calls to state->pdata->uart_putc to a debug_putc
helper.
Change-Id: Idc007bd170ff1b51d0325e238105ae0c86d23777
Signed-off-by: Colin Cross <ccross@android.com>
Pass the rest of the reboot command to kernel_restart to allow
reboot bootloader to work from FIQ debugger.
Change-Id: I4e7b366a69268dda17ffcf4c84f2373d15cb1271
Signed-off-by: Colin Cross <ccross@android.com>
Call kernel_restart instead of arch_reset, the ARM reset handling
has changed.
Remove localtimer irq printing, they now show up in the regular
irq stats.
Change-Id: I523da343b292c5711f3e1cbfd766d32eea2da84e
Signed-off-by: Colin Cross <ccross@android.com>
When an ep_out req is dequeued because of userspace freezing,
don't set the error flag.
Change-Id: I680f1a1059b8ac2244aaa069e7d42dc44abf98e9
Signed-off-by: Colin Cross <ccross@android.com>
wait_event_interruptible in adb_read might return -ERESTARTSYS if
userspace is frozen during adb_read or another signal is delivered
to adb. If so, don't set dev->error to avoid resetting the adb
connection.
Change-Id: I5a7baa013a9a3a3b5305de7e6a0d18546a560018
Signed-off-by: Colin Cross <ccross@android.com>
USB accessory mode allows users to connect USB host hardware
specifically designed for Android-powered devices. The accessories
must adhere to the Android accessory protocol outlined in the
http://accessories.android.com documentation. This allows
Android devices that cannot act as a USB host to still interact with
USB hardware. When an Android device is in USB accessory mode, the
attached Android USB accessory acts as the host, provides power
to the USB bus, and enumerates connected devices.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Android Debug Bridge (adb) is a command line tool that lets
users communicate with a Android-powered device. It is used
mainly to debug applications and tranfer files. f_adb implements
the transport layer between the ADB Server (on the host) and the
ADBD daemon (on the device).
Signed-off-by: Mike Lockwood <lockwood@android.com>
