commit 5d54cb1767 upstream.
Commit a97f8783a9 ("igb: unbreak I2C bit-banging on i350") introduced
code to change I2C settings to bit banging unconditionally.
However, this patch introduced a regression: On an Intel S2600CWR
Server Board with three NICs:
- 1x dual-port copper
Intel I350 Gigabit Network Connection [8086:1521] (rev 01)
fw 1.63, 0x80000dda
- 2x quad-port SFP+ with copper SFP Avago ABCU-5700RZ
Intel I350 Gigabit Fiber Network Connection [8086:1522] (rev 01)
fw 1.52.0
the SFP NICs no longer get link at all. Reverting commit a97f8783a9
or switching to the Intel out-of-tree driver both fix the problem.
Per the igb out-of-tree driver, I2C bit banging on i350 depends on
support for an external thermal sensor (ETS). However, commit
a97f8783a9 added bit banging unconditionally. Additionally, the
out-of-tree driver always calls init_thermal_sensor_thresh on probe,
while our driver only calls init_thermal_sensor_thresh only in
igb_reset(), and only if an ETS is present, ignoring the internal
thermal sensor. The affected SFPs don't provide an ETS. Per Intel,
the behaviour is a result of i350 firmware requirements.
This patch fixes the problem by aligning the behaviour to the
out-of-tree driver:
- split igb_init_i2c() into two functions:
- igb_init_i2c() only performs the basic I2C initialization.
- igb_set_i2c_bb() makes sure that E1000_CTRL_I2C_ENA is set
and enables bit-banging.
- igb_probe() only calls igb_set_i2c_bb() if an ETS is present.
- igb_probe() calls init_thermal_sensor_thresh() unconditionally.
- igb_reset() aligns its behaviour to igb_probe(), i. e., call
igb_set_i2c_bb() if an ETS is present and call
init_thermal_sensor_thresh() unconditionally.
Fixes: a97f8783a9 ("igb: unbreak I2C bit-banging on i350")
Tested-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Co-developed-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230214185549.1306522-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fda6c89fe3 upstream.
lianhui reports that when MPLS fails to register the sysctl table
under new location (during device rename) the old pointers won't
get overwritten and may be freed again (double free).
Handle this gracefully. The best option would be unregistering
the MPLS from the device completely on failure, but unfortunately
mpls_ifdown() can fail. So failing fully is also unreliable.
Another option is to register the new table first then only
remove old one if the new one succeeds. That requires more
code, changes order of notifications and two tables may be
visible at the same time.
sysctl point is not used in the rest of the code - set to NULL
on failures and skip unregister if already NULL.
Reported-by: lianhui tang <bluetlh@gmail.com>
Fixes: 0fae3bf018 ("mpls: handle device renames for per-device sysctls")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05d7623a89 upstream.
When setting 'snps,force_thresh_dma_mode' DT property, the following
warning is always emitted, regardless the status of force_sf_dma_mode:
dwmac-starfive 10020000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
Do not print the rather misleading message when DMA store and forward
mode is already disabled.
Fixes: e2a240c7d3 ("driver:net:stmmac: Disable DMA store and forward mode if platform data force_thresh_dma_mode is set.")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230210202126.877548-1-cristian.ciocaltea@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2038cc5928 upstream.
In bnxt_reserve_rings(), there is logic to check that the number of TX
rings reserved is enough to cover all the mqprio TCs, but it fails to
account for the TX XDP rings. So the check will always fail if there
are mqprio TCs and TX XDP rings. As a result, the driver always fails
to initialize after the XDP program is attached and the device will be
brought down. A subsequent ifconfig up will also fail because the
number of TX rings is set to an inconsistent number. Fix the check to
properly account for TX XDP rings. If the check fails, set the number
of TX rings back to a consistent number after calling netdev_reset_tc().
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4562c65ec8 upstream.
So far changing the period by just setting new period values while
running did not work.
The order as indicated by the publicly available reference manual of the i.MX8MP [1]
indicates a sequence:
* initiate the programming sequence
* set the values for PPS period and start time
* start the pulse train generation.
This is currently not used in dwmac5_flex_pps_config(), which instead does:
* initiate the programming sequence and immediately start the pulse train generation
* set the values for PPS period and start time
This caused the period values written not to take effect until the FlexPPS output was
disabled and re-enabled again.
This patch fix the order and allows the period to be set immediately.
[1] https://www.nxp.com/webapp/Download?colCode=IMX8MPRM
Fixes: 9a8a02c9d4 ("net: stmmac: Add Flexible PPS support")
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230210143937.3427483-1-j.zink@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21c167aa0b upstream.
The tc action act_ctinfo was using shared stats, fix it to use percpu stats
since bstats_update() must be called with locks or with a percpu pointer argument.
tdc results:
1..12
ok 1 c826 - Add ctinfo action with default setting
ok 2 0286 - Add ctinfo action with dscp
ok 3 4938 - Add ctinfo action with valid cpmark and zone
ok 4 7593 - Add ctinfo action with drop control
ok 5 2961 - Replace ctinfo action zone and action control
ok 6 e567 - Delete ctinfo action with valid index
ok 7 6a91 - Delete ctinfo action with invalid index
ok 8 5232 - List ctinfo actions
ok 9 7702 - Flush ctinfo actions
ok 10 3201 - Add ctinfo action with duplicate index
ok 11 8295 - Add ctinfo action with invalid index
ok 12 3964 - Replace ctinfo action with invalid goto_chain control
Fixes: 24ec483cec ("net: sched: Introduce act_ctinfo action")
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20230210200824.444856-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c68f345b7c upstream.
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
1: https://lore.kernel.org/lkml/Y9pY61y1nwTuzMOa@nanopsycho/
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Reported-and-tested-by: syzbot+cd80c5ef5121bfe85b55@syzkaller.appspotmail.com
Signed-off-by: Miko Larsson <mikoxyzzz@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca43ccf412 upstream.
Eric Dumazet pointed out [0] that when we call skb_set_owner_r()
for ipv6_pinfo.pktoptions, sk_rmem_schedule() has not been called,
resulting in a negative sk_forward_alloc.
We add a new helper which clones a skb and sets its owner only
when sk_rmem_schedule() succeeds.
Note that we move skb_set_owner_r() forward in (dccp|tcp)_v6_do_rcv()
because tcp_send_synack() can make sk_forward_alloc negative before
ipv6_opt_accepted() in the crossed SYN-ACK or self-connect() cases.
[0]: https://lore.kernel.org/netdev/CANn89iK9oc20Jdi_41jb9URdF210r7d1Y-+uypbMSbOfY6jqrg@mail.gmail.com/
Fixes: 323fbd0edf ("net: dccp: Add handling of IPV6_PKTOPTIONS to dccp_v6_do_rcv()")
Fixes: 3df80d9320 ("[DCCP]: Introduce DCCPv6")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee059170b1 upstream.
The imperfect hash area can be updated while packets are traversing,
which will cause a use-after-free when 'tcf_exts_exec()' is called
with the destroyed tcf_ext.
CPU 0: CPU 1:
tcindex_set_parms tcindex_classify
tcindex_lookup
tcindex_lookup
tcf_exts_change
tcf_exts_exec [UAF]
Stop operating on the shared area directly, by using a local copy,
and update the filter with 'rcu_replace_pointer()'. Delete the old
filter version only after a rcu grace period elapsed.
Fixes: 9b0d4446b5 ("net: sched: avoid atomic swap in tcf_exts_change")
Reported-by: valis <sec@valis.email>
Suggested-by: valis <sec@valis.email>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Link: https://lore.kernel.org/r/20230209143739.279867-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ed577e7e8 upstream.
In TI's AM62x/AM64x SoCs, successful teardown of RX DMA Channel raises an
interrupt. The process of servicing this interrupt involves flushing all
pending RX DMA descriptors and clearing the teardown completion marker
(TDCM). The am65_cpsw_nuss_rx_packets() function invoked from the RX
NAPI callback services the interrupt. Thus, it is necessary to wait for
this handler to run, drain all packets and clear TDCM, before calling
napi_disable() in am65_cpsw_nuss_common_stop() function post channel
teardown. If napi_disable() executes before ensuring that TDCM is
cleared, the TDCM remains set when the interfaces are down, resulting in
an interrupt storm when the interfaces are brought up again.
Since the interrupt raised to indicate the RX DMA Channel teardown is
specific to the AM62x and AM64x SoCs, add a quirk for it.
Fixes: 4f7cce2724 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g")
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230209084432.189222-1-s-vadapalli@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9cd6a4418 upstream.
Recently I encountered one case where I cannot increase the MTU size
directly from 1500 to a much bigger value with XDP enabled if the
server is equipped with IXGBE card, which happened on thousands of
servers in production environment. After applying the current patch,
we can set the maximum MTU size to 3K.
This patch follows the behavior of changing MTU as i40e/ice does.
References:
[1] commit 23b44513c3 ("ice: allow 3k MTU for XDP")
[2] commit 0c8493d90b ("i40e: add XDP support for pass and drop actions")
Fixes: fabf1bce10 ("ixgbe: Prevent unsupported configurations with XDP")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43fbca02c2 upstream.
There was a problem reported to us where the addition of a VF with an IPv6
address ending with a particular sequence would cause the parent device on
the PF to no longer be able to respond to neighbor discovery packets.
In this case, we had an ovs-bridge device living on top of a VLAN, which
was on top of a PF, and it would not be able to talk anymore (the neighbor
entry would expire and couldn't be restored).
The root cause of the issue is that if the PF is asked to be in IFF_PROMISC
mode (promiscuous mode) and it had an ipv6 address that needed the
33:33:ff:00:00:04 multicast address to work, then when the VF was added
with the need for the same multicast address, the VF would steal all the
traffic destined for that address.
The ice driver didn't auto-subscribe a request of IFF_PROMISC to the
"multicast replication from other port's traffic" meaning that it won't get
for instance, packets with an exact destination in the VF, as above.
The VF's IPv6 address, which adds a "perfect filter" for 33:33:ff:00:00:04,
results in no packets for that multicast address making it to the PF (which
is in promisc but NOT "multicast replication").
The fix is to enable "multicast promiscuous" whenever the driver is asked
to enable IFF_PROMISC, and make sure to disable it when appropriate.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b77b16de7 upstream.
YUV images can either be presented as one allocation with offsets
for the different planes, or multiple allocations with 0 offsets.
The driver only ever calls drm_fb_[dma|cma]_get_gem_obj with plane
index 0, therefore any application using the second approach was
incorrectly rendered.
Correctly determine the address for each plane, removing the
assumption that the base address is the same for each.
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127155708.454704-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 247a631f9c upstream.
The formula that determines the core clock requirement based on pixel
clock and blanking has been determined experimentally to minimise the
clock while supporting all modes we've seen.
A new reduced blanking mode (4kp60 at 533MHz rather than the standard
594MHz) has been seen that doesn't produce a high enough clock and
results in "flip_done timed out" error.
Increase the setup cost in the formula to make this work. The result is
a reduced blanking mode increases by up to 7MHz while leaving the
standard timing
mode untouched
Link: https://github.com/raspberrypi/linux/issues/4446
Fixes: 16e101051f ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127145558.446123-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b55d3f0a6 upstream.
When converting net_device_stats to rtnl_link_stats64 sign extension
is triggered on ILP32 machines as 6c1c509778 changed the previous
"ulong -> u64" conversion to "long -> u64" by accessing the
net_device_stats fields through a (signed) atomic_long_t.
This causes for example the received bytes counter to jump to 16EiB after
having received 2^31 bytes. Casting the atomic value to "unsigned long"
beforehand converting it into u64 avoids this.
Fixes: 6c1c509778 ("net: add atomic_long_t to net_device_stats fields")
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 647037adca upstream.
This reverts commit 115d9d77bb.
The pages being freed by memblock_free_late() have already been
initialized, but if they are in the deferred init range,
__free_one_page() might access nearby uninitialized pages when trying to
coalesce buddies. This can, for example, trigger this BUG:
BUG: unable to handle page fault for address: ffffe964c02580c8
RIP: 0010:__list_del_entry_valid+0x3f/0x70
<TASK>
__free_one_page+0x139/0x410
__free_pages_ok+0x21d/0x450
memblock_free_late+0x8c/0xb9
efi_free_boot_services+0x16b/0x25c
efi_enter_virtual_mode+0x403/0x446
start_kernel+0x678/0x714
secondary_startup_64_no_verify+0xd2/0xdb
</TASK>
A proper fix will be more involved so revert this change for the time
being.
Fixes: 115d9d77bb ("mm: Always release pages to the buddy allocator in memblock_free_late().")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Link: https://lore.kernel.org/r/20230207082151.1303-1-dev@aaront.org
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c7417b5ec upstream.
If CONFIG_ELF_CORE is not set:
fs/coredump.c:835:12: error: ‘dump_emit_page’ defined but not used [-Werror=unused-function]
835 | static int dump_emit_page(struct coredump_params *cprm, struct page *page)
| ^~~~~~~~~~~~~~
Fix this by moving dump_emit_page() inside the existing section
protected by #ifdef CONFIG_ELF_CORE.
Fixes: 06bbaa6dc5 ("[coredump] don't use __kernel_write() on kmap_local_page()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5956592ce3 upstream.
I was running traces of the read code against an RAID storage system to
understand why read requests were being misaligned against the underlying
RAID strips. I found that the page end offset calculation in
filemap_get_read_batch() was off by one.
When a read is submitted with end offset 1048575, then it calculates the
end page for read of 256 when it should be 255. "last_index" is the index
of the page beyond the end of the read and it should be skipped when get a
batch of pages for read in @filemap_get_read_batch().
The below simple patch fixes the problem. This code was introduced in
kernel 5.12.
Link: https://lkml.kernel.org/r/20230208022400.28962-1-coolqyj@163.com
Fixes: cbd59c48ae ("mm/filemap: use head pages in generic_file_buffered_read")
Signed-off-by: Qian Yingjin <qian@ddn.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae63c898f4 upstream.
During collapse, in a few places we check to see if a given small page has
any unaccounted references. If the refcount on the page doesn't match our
expectations, it must be there is an unknown user concurrently interested
in the page, and so it's not safe to move the contents elsewhere.
However, the unaccounted pins are likely an ephemeral state.
In this situation, MADV_COLLAPSE returns -EINVAL when it should return
-EAGAIN. This could cause userspace to conclude that the syscall
failed, when it in fact could succeed by retrying.
Link: https://lkml.kernel.org/r/20230125015738.912924-1-zokeefe@google.com
Fixes: 7d8faaf155 ("mm/madvise: introduce MADV_COLLAPSE sync hugepage collapse")
Signed-off-by: Zach O'Keefe <zokeefe@google.com>
Reported-by: Hugh Dickins <hughd@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99b9402a36 upstream.
Macro NILFS_SB2_OFFSET_BYTES, which computes the position of the second
superblock, underflows when the argument device size is less than 4096
bytes. Therefore, when using this macro, it is necessary to check in
advance that the device size is not less than a lower limit, or at least
that underflow does not occur.
The current nilfs2 implementation lacks this check, causing out-of-bound
block access when mounting devices smaller than 4096 bytes:
I/O error, dev loop0, sector 36028797018963960 op 0x0:(READ) flags 0x0
phys_seg 1 prio class 2
NILFS (loop0): unable to read secondary superblock (blocksize = 1024)
In addition, when trying to resize the filesystem to a size below 4096
bytes, this underflow occurs in nilfs_resize_fs(), passing a huge number
of segments to nilfs_sufile_resize(), corrupting parameters such as the
number of segments in superblocks. This causes excessive loop iterations
in nilfs_sufile_resize() during a subsequent resize ioctl, causing
semaphore ns_segctor_sem to block for a long time and hang the writer
thread:
INFO: task segctord:5067 blocked for more than 143 seconds.
Not tainted 6.2.0-rc8-syzkaller-00015-gf6feea56f66d #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:segctord state:D stack:23456 pid:5067 ppid:2
flags:0x00004000
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5293 [inline]
__schedule+0x1409/0x43f0 kernel/sched/core.c:6606
schedule+0xc3/0x190 kernel/sched/core.c:6682
rwsem_down_write_slowpath+0xfcf/0x14a0 kernel/locking/rwsem.c:1190
nilfs_transaction_lock+0x25c/0x4f0 fs/nilfs2/segment.c:357
nilfs_segctor_thread_construct fs/nilfs2/segment.c:2486 [inline]
nilfs_segctor_thread+0x52f/0x1140 fs/nilfs2/segment.c:2570
kthread+0x270/0x300 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
</TASK>
...
Call Trace:
<TASK>
folio_mark_accessed+0x51c/0xf00 mm/swap.c:515
__nilfs_get_page_block fs/nilfs2/page.c:42 [inline]
nilfs_grab_buffer+0x3d3/0x540 fs/nilfs2/page.c:61
nilfs_mdt_submit_block+0xd7/0x8f0 fs/nilfs2/mdt.c:121
nilfs_mdt_read_block+0xeb/0x430 fs/nilfs2/mdt.c:176
nilfs_mdt_get_block+0x12d/0xbb0 fs/nilfs2/mdt.c:251
nilfs_sufile_get_segment_usage_block fs/nilfs2/sufile.c:92 [inline]
nilfs_sufile_truncate_range fs/nilfs2/sufile.c:679 [inline]
nilfs_sufile_resize+0x7a3/0x12b0 fs/nilfs2/sufile.c:777
nilfs_resize_fs+0x20c/0xed0 fs/nilfs2/super.c:422
nilfs_ioctl_resize fs/nilfs2/ioctl.c:1033 [inline]
nilfs_ioctl+0x137c/0x2440 fs/nilfs2/ioctl.c:1301
...
This fixes these issues by inserting appropriate minimum device size
checks or anti-underflow checks, depending on where the macro is used.
Link: https://lkml.kernel.org/r/0000000000004e1dfa05f4a48e6b@google.com
Link: https://lkml.kernel.org/r/20230214224043.24141-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: <syzbot+f0c4082ce5ebebdac63b@syzkaller.appspotmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec4288fe63 upstream.
Users can specify the hugetlb page size in the mmap, shmget and
memfd_create system calls. This is done by using 6 bits within the flags
argument to encode the base-2 logarithm of the desired page size. The
routine hstate_sizelog() uses the log2 value to find the corresponding
hugetlb hstate structure. Converting the log2 value (page_size_log) to
potential hugetlb page size is the simple statement:
1UL << page_size_log
Because only 6 bits are used for page_size_log, the left shift can not be
greater than 63. This is fine on 64 bit architectures where a long is 64
bits. However, if a value greater than 31 is passed on a 32 bit
architecture (where long is 32 bits) the shift will result in undefined
behavior. This was generally not an issue as the result of the undefined
shift had to exactly match hugetlb page size to proceed.
Recent improvements in runtime checking have resulted in this undefined
behavior throwing errors such as reported below.
Fix by comparing page_size_log to BITS_PER_LONG before doing shift.
Link: https://lkml.kernel.org/r/20230216013542.138708-1-mike.kravetz@oracle.com
Link: https://lore.kernel.org/lkml/CA+G9fYuei_Tr-vN9GS7SfFyU1y9hNysnf=PB7kT0=yv4MiPgVg@mail.gmail.com/
Fixes: 42d7395feb ("mm: support more pagesizes for MAP_HUGETLB/SHM_HUGETLB")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Jesper Juhl <jesperjuhl76@gmail.com>
Acked-by: Muchun Song <songmuchun@bytedance.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2dbe32d5d upstream.
If a non-root cgroup gets removed when there is a thread that registered
trigger and is polling on a pressure file within the cgroup, the polling
waitqueue gets freed in the following path:
do_rmdir
cgroup_rmdir
kernfs_drain_open_files
cgroup_file_release
cgroup_pressure_release
psi_trigger_destroy
However, the polling thread still has a reference to the pressure file and
will access the freed waitqueue when the file is closed or upon exit:
fput
ep_eventpoll_release
ep_free
ep_remove_wait_queue
remove_wait_queue
This results in use-after-free as pasted below.
The fundamental problem here is that cgroup_file_release() (and
consequently waitqueue's lifetime) is not tied to the file's real lifetime.
Using wake_up_pollfree() here might be less than ideal, but it is in line
with the comment at commit 42288cb44c ("wait: add wake_up_pollfree()")
since the waitqueue's lifetime is not tied to file's one and can be
considered as another special case. While this would be fixable by somehow
making cgroup_file_release() be tied to the fput(), it would require
sizable refactoring at cgroups or higher layer which might be more
justifiable if we identify more cases like this.
BUG: KASAN: use-after-free in _raw_spin_lock_irqsave+0x60/0xc0
Write of size 4 at addr ffff88810e625328 by task a.out/4404
CPU: 19 PID: 4404 Comm: a.out Not tainted 6.2.0-rc6 #38
Hardware name: Amazon EC2 c5a.8xlarge/, BIOS 1.0 10/16/2017
Call Trace:
<TASK>
dump_stack_lvl+0x73/0xa0
print_report+0x16c/0x4e0
kasan_report+0xc3/0xf0
kasan_check_range+0x2d2/0x310
_raw_spin_lock_irqsave+0x60/0xc0
remove_wait_queue+0x1a/0xa0
ep_free+0x12c/0x170
ep_eventpoll_release+0x26/0x30
__fput+0x202/0x400
task_work_run+0x11d/0x170
do_exit+0x495/0x1130
do_group_exit+0x100/0x100
get_signal+0xd67/0xde0
arch_do_signal_or_restart+0x2a/0x2b0
exit_to_user_mode_prepare+0x94/0x100
syscall_exit_to_user_mode+0x20/0x40
do_syscall_64+0x52/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Allocated by task 4404:
kasan_set_track+0x3d/0x60
__kasan_kmalloc+0x85/0x90
psi_trigger_create+0x113/0x3e0
pressure_write+0x146/0x2e0
cgroup_file_write+0x11c/0x250
kernfs_fop_write_iter+0x186/0x220
vfs_write+0x3d8/0x5c0
ksys_write+0x90/0x110
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 4407:
kasan_set_track+0x3d/0x60
kasan_save_free_info+0x27/0x40
____kasan_slab_free+0x11d/0x170
slab_free_freelist_hook+0x87/0x150
__kmem_cache_free+0xcb/0x180
psi_trigger_destroy+0x2e8/0x310
cgroup_file_release+0x4f/0xb0
kernfs_drain_open_files+0x165/0x1f0
kernfs_drain+0x162/0x1a0
__kernfs_remove+0x1fb/0x310
kernfs_remove_by_name_ns+0x95/0xe0
cgroup_addrm_files+0x67f/0x700
cgroup_destroy_locked+0x283/0x3c0
cgroup_rmdir+0x29/0x100
kernfs_iop_rmdir+0xd1/0x140
vfs_rmdir+0xfe/0x240
do_rmdir+0x13d/0x280
__x64_sys_rmdir+0x2c/0x30
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: 0e94682b73 ("psi: introduce psi monitor")
Signed-off-by: Munehisa Kamata <kamatam@amazon.com>
Signed-off-by: Mengchi Cheng <mengcc@amazon.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/20230106224859.4123476-1-kamatam@amazon.com/
Link: https://lore.kernel.org/r/20230214212705.4058045-1-kamatam@amazon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ead089577e upstream.
Samsung MZ7LH drives are spewing messages like this in to dmesg with AMD
SATA controllers:
ata1.00: exception Emask 0x0 SAct 0x7e0000 SErr 0x0 action 0x6 frozen
ata1.00: failed command: SEND FPDMA QUEUED
ata1.00: cmd 64/01:88:00:00:00/00:00:00:00:00/a0 tag 17 ncq dma 512 out
res 40/00:01:01:4f:c2/00:00:00:00:00/00 Emask
0x4 (timeout)
Since this was seen previously with SSD 840 EVO drives in
https://bugzilla.kernel.org/show_bug.cgi?id=203475 let's add the same
fix for these drives as the EVOs have, since they likely have very
similar firmwares.
Signed-off-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3af4a4f7a2 upstream.
Commit f2bd1c5ae2 ("ALSA: hda: Fix page fault in
snd_hda_codec_shutdown()") relocated initialization of several codec
device fields. Due to differences between codec_exec_verb() and
snd_hdac_bus_exec_bus() in how they handle VERB execution - the latter
does not touch PM - assigning ->exec_verb to codec_exec_verb() causes PM
to be engaged before it is configured for the device. Configuration of
PM for the ASoC HDAudio sound card is done with snd_hda_set_power_save()
during skl_hda_audio_probe() whereas the assignment happens early, in
snd_hda_codec_device_init().
Revert to previous behavior to avoid problems caused by too early PM
manipulation.
Suggested-by: Jason Montleon <jmontleo@redhat.com>
Link: https://lore.kernel.org/regressions/CALFERdzKUodLsm6=Ub3g2+PxpNpPtPq3bGBLbff=eZr9_S=YVA@mail.gmail.com
Fixes: f2bd1c5ae2 ("ALSA: hda: Fix page fault in snd_hda_codec_shutdown()")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230210165541.3543604-1-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 605d9fb955 upstream.
If sdio_add_func() or sdio_init_func() fails, sdio_remove_func() can
not release the resources, because the sdio function is not presented
in these two cases, it won't call of_node_put() or put_device().
To fix these leaks, make sdio_func_present() only control whether
device_del() needs to be called or not, then always call of_node_put()
and put_device().
In error case in sdio_init_func(), the reference of 'card->dev' is
not get, to avoid redundant put in sdio_free_func_cis(), move the
get_device() to sdio_alloc_func() and put_device() to sdio_release_func(),
it can keep the get/put function be balanced.
Without this patch, while doing fault inject test, it can get the
following leak reports, after this fix, the leak is gone.
unreferenced object 0xffff888112514000 (size 2048):
comm "kworker/3:2", pid 65, jiffies 4294741614 (age 124.774s)
hex dump (first 32 bytes):
00 e0 6f 12 81 88 ff ff 60 58 8d 06 81 88 ff ff ..o.....`X......
10 40 51 12 81 88 ff ff 10 40 51 12 81 88 ff ff .@Q......@Q.....
backtrace:
[<000000009e5931da>] kmalloc_trace+0x21/0x110
[<000000002f839ccb>] mmc_alloc_card+0x38/0xb0 [mmc_core]
[<0000000004adcbf6>] mmc_sdio_init_card+0xde/0x170 [mmc_core]
[<000000007538fea0>] mmc_attach_sdio+0xcb/0x1b0 [mmc_core]
[<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core]
unreferenced object 0xffff888112511000 (size 2048):
comm "kworker/3:2", pid 65, jiffies 4294741623 (age 124.766s)
hex dump (first 32 bytes):
00 40 51 12 81 88 ff ff e0 58 8d 06 81 88 ff ff .@Q......X......
10 10 51 12 81 88 ff ff 10 10 51 12 81 88 ff ff ..Q.......Q.....
backtrace:
[<000000009e5931da>] kmalloc_trace+0x21/0x110
[<00000000fcbe706c>] sdio_alloc_func+0x35/0x100 [mmc_core]
[<00000000c68f4b50>] mmc_attach_sdio.cold.18+0xb1/0x395 [mmc_core]
[<00000000d4fdeba7>] mmc_rescan+0x54a/0x640 [mmc_core]
Fixes: 3d10a1ba0d ("sdio: fix reference counting in sdio_remove_func()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230130125808.3471254-1-yangyingliang@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a950b989ea upstream.
v3: Fix vmw_user_bo_lookup which was also dropping the gem reference
before the kernel was done with buffer depending on userspace doing
the right thing. Same bug, different spot.
It is possible for userspace to predict the next buffer handle and
to destroy the buffer while it's still used by the kernel. Delay
dropping the internal reference on the buffers until kernel is done
with them.
Instead of immediately dropping the gem reference in vmw_user_bo_lookup
and vmw_gem_object_create_with_handle let the callers decide when they're
ready give the control back to userspace.
Also fixes the second usage of vmw_gem_object_create_with_handle in
vmwgfx_surface.c which wasn't grabbing an explicit reference
to the gem object which could have been destroyed by the userspace
on the owning surface at any point.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 8afa13a058 ("drm/vmwgfx: Implement DRIVER_GEM")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211050514.2431155-1-zack@kde.org
(cherry picked from commit 9ef8d83e8e)
Cc: <stable@vger.kernel.org> # v5.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a6897921f upstream.
ttm_bo_init_reserved on failure puts the buffer object back which
causes it to be deleted, but kfree was still being called on the same
buffer in vmw_bo_create leading to a double free.
After the double free the vmw_gem_object_create_with_handle was
setting the gem function objects before checking the return status
of vmw_bo_create leading to null pointer access.
Fix the entire path by relaying on ttm_bo_init_reserved to delete the
buffer objects on failure and making sure the return status is checked
before setting the gem function objects on the buffer object.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 8afa13a058 ("drm/vmwgfx: Implement DRIVER_GEM")
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208180050.2093426-1-zack@kde.org
(cherry picked from commit 36d421e632)
Cc: <stable@vger.kernel.org> # v5.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
