commit 93b8ddc54507a227087c60a0013ed833b6ae7d3c upstream.
The current implementation only calls chained_irq_enter() and
chained_irq_exit() if it detects pending interrupts.
```
for (i = 0; i < info->stride; i++) {
uregmap_read(info->map, id_reg + 4 * i, ®);
if (!reg)
continue;
chained_irq_enter(parent_chip, desc);
```
However, in case of GPIO pin configured in level mode and the parent
controller configured in edge mode, GPIO interrupt might be lowered by the
hardware. In the result, if the interrupt is short enough, the parent
interrupt is still pending while the GPIO interrupt is cleared;
chained_irq_enter() never gets called and the system hangs trying to
service the parent interrupt.
Moving chained_irq_enter() and chained_irq_exit() outside the for loop
ensures that they are called even when GPIO interrupt is lowered by the
hardware.
The similar code with chained_irq_enter() / chained_irq_exit() functions
wrapping interrupt checking loop may be found in many other drivers:
```
grep -r -A 10 chained_irq_enter drivers/pinctrl
```
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/20241012105743.12450-2-matsievskiysv@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d2102018542e3ae5e297bc6e229303abff8a0f upstream.
Robert Gill reported below #GP in 32-bit mode when dosemu software was
executing vm86() system call:
general protection fault: 0000 [#1] PREEMPT SMP
CPU: 4 PID: 4610 Comm: dosemu.bin Not tainted 6.6.21-gentoo-x86 #1
Hardware name: Dell Inc. PowerEdge 1950/0H723K, BIOS 2.7.0 10/30/2010
EIP: restore_all_switch_stack+0xbe/0xcf
EAX: 00000000 EBX: 00000000 ECX: 00000000 EDX: 00000000
ESI: 00000000 EDI: 00000000 EBP: 00000000 ESP: ff8affdc
DS: 0000 ES: 0000 FS: 0000 GS: 0033 SS: 0068 EFLAGS: 00010046
CR0: 80050033 CR2: 00c2101c CR3: 04b6d000 CR4: 000406d0
Call Trace:
show_regs+0x70/0x78
die_addr+0x29/0x70
exc_general_protection+0x13c/0x348
exc_bounds+0x98/0x98
handle_exception+0x14d/0x14d
exc_bounds+0x98/0x98
restore_all_switch_stack+0xbe/0xcf
exc_bounds+0x98/0x98
restore_all_switch_stack+0xbe/0xcf
This only happens in 32-bit mode when VERW based mitigations like MDS/RFDS
are enabled. This is because segment registers with an arbitrary user value
can result in #GP when executing VERW. Intel SDM vol. 2C documents the
following behavior for VERW instruction:
#GP(0) - If a memory operand effective address is outside the CS, DS, ES,
FS, or GS segment limit.
CLEAR_CPU_BUFFERS macro executes VERW instruction before returning to user
space. Use %cs selector to reference VERW operand. This ensures VERW will
not #GP for an arbitrary user %ds.
[ mingo: Fixed the SOB chain. ]
Fixes: a0e2dab44d22 ("x86/entry_32: Add VERW just before userspace transition")
Reported-by: Robert Gill <rtgill82@gmail.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com
Cc: stable@vger.kernel.org # 5.10+
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218707
Closes: https://lore.kernel.org/all/8c77ccfd-d561-45a1-8ed5-6b75212c7a58@leemhuis.info/
Suggested-by: Dave Hansen <dave.hansen@linux.intel.com>
Suggested-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee4d4e8d2c3bec6ee652599ab31991055a72c322 upstream.
Commit
f69759be251d ("x86/CPU/AMD: Move Zenbleed check to the Zen2 init function")
causes a bit in the DE_CFG MSR to get set erroneously after a microcode late
load.
The microcode late load path calls into amd_check_microcode() and subsequently
zen2_zenbleed_check(). Since the above commit removes the cpu_has_amd_erratum()
call from zen2_zenbleed_check(), this will cause all non-Zen2 CPUs to go
through the function and set the bit in the DE_CFG MSR.
Call into the Zenbleed fix path on Zen2 CPUs only.
[ bp: Massage commit message, use cpu_feature_enabled(). ]
Fixes: f69759be251d ("x86/CPU/AMD: Move Zenbleed check to the Zen2 init function")
Signed-off-by: John Allen <john.allen@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240923164404.27227-1-john.allen@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffd95846c6ec6cf1f93da411ea10d504036cab42 upstream.
New processors have become pickier about the local APIC timer state
before entering low power modes. These low power modes are used (for
example) when you close your laptop lid and suspend. If you put your
laptop in a bag and it is not in this low power mode, it is likely
to get quite toasty while it quickly sucks the battery dry.
The problem boils down to some CPUs' inability to power down until the
CPU recognizes that the local APIC timer is shut down. The current
kernel code works in one-shot and periodic modes but does not work for
deadline mode. Deadline mode has been the supported and preferred mode
on Intel CPUs for over a decade and uses an MSR to drive the timer
instead of an APIC register.
Disable the TSC Deadline timer in lapic_timer_shutdown() by writing to
MSR_IA32_TSC_DEADLINE when in TSC-deadline mode. Also avoid writing
to the initial-count register (APIC_TMICT) which is ignored in
TSC-deadline mode.
Note: The APIC_LVTT|=APIC_LVT_MASKED operation should theoretically be
enough to tell the hardware that the timer will not fire in any of the
timer modes. But mitigating AMD erratum 411[1] also requires clearing
out APIC_TMICT. Solely setting APIC_LVT_MASKED is also ineffective in
practice on Intel Lunar Lake systems, which is the motivation for this
change.
1. 411 Processor May Exit Message-Triggered C1E State Without an Interrupt if Local APIC Timer Reaches Zero - https://www.amd.com/content/dam/amd/en/documents/archived-tech-docs/revision-guides/41322_10h_Rev_Gd.pdf
Fixes: 279f146143 ("x86: apic: Use tsc deadline for oneshot when available")
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Todd Brandt <todd.e.brandt@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241015061522.25288-1-rui.zhang%40intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5fd042bf4cfb557981d65628e1779a492cd8cfa upstream.
After a recent LLVM change [1] that deduces __cold on functions that only call
cold code (such as __init functions), there is a section mismatch warning from
__get_mem_config_intel(), which got moved to .text.unlikely. as a result of
that optimization:
WARNING: modpost: vmlinux: section mismatch in reference: \
__get_mem_config_intel+0x77 (section: .text.unlikely.) -> thread_throttle_mode_init (section: .init.text)
Mark __get_mem_config_intel() as __init as well since it is only called
from __init code, which clears up the warning.
While __rdt_get_mem_config_amd() does not exhibit a warning because it
does not call any __init code, it is a similar function that is only
called from __init code like __get_mem_config_intel(), so mark it __init
as well to keep the code symmetrical.
CONFIG_SECTION_MISMATCH_WARN_ONLY=n would turn this into a fatal error.
Fixes: 05b93417ce ("x86/intel_rdt/mba: Add primary support for Memory Bandwidth Allocation (MBA)")
Fixes: 4d05bf71f1 ("x86/resctrl: Introduce AMD QOS feature")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: <stable@kernel.org>
Link: 6b11573b8c [1]
Link: https://lore.kernel.org/r/20240917-x86-restctrl-get_mem_config_intel-init-v3-1-10d521256284@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02ac3a9ef3a18b58d8f3ea2b6e46de657bf6c4f9 upstream.
The recent fix for array out-of-bounds accesses replaced sprintf()
calls blindly with snprintf(). However, since snprintf() returns the
would-be-printed size, not the actually output size, the length
calculation can still go over the given limit.
Use scnprintf() instead of snprintf(), which returns the actually
output letters, for addressing the potential out-of-bounds access
properly.
Fixes: ab11dac93d2d ("dev/parport: fix the array out-of-bounds risk")
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20240920103318.19271-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40d7903386df4d18f04d90510ba90eedee260085 upstream.
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c96e31252110a84dcc44412e8a7b456b33c3e298 upstream.
DWC3 programming guide mentions that when operating in USB2.0 speeds,
if GUSB2PHYCFG[6] or GUSB2PHYCFG[8] is set, it must be cleared prior
to issuing commands and may be set again after the command completes.
But currently while issuing EndXfer command without CmdIOC set, we
wait for 1ms after GUSB2PHYCFG is restored. This results in cases
where EndXfer command doesn't get completed and causes SMMU faults
since requests are unmapped afterwards. Hence restore GUSB2PHYCFG
after waiting for EndXfer command completion.
Cc: stable@vger.kernel.org
Fixes: 1d26ba0944d3 ("usb: dwc3: Wait unconditionally after issuing EndXfer command")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240924093208.2524531-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe49df60cdb7c2975aa743dc295f8786e4b7db10 upstream.
Avoid xHC host from processing a cancelled URB by always turning
cancelled URB TDs into no-op TRBs before queuing a 'Set TR Deq' command.
If the command fails then xHC will start processing the cancelled TD
instead of skipping it once endpoint is restarted, causing issues like
Babble error.
This is not a complete solution as a failed 'Set TR Deq' command does not
guarantee xHC TRB caches are cleared.
Fixes: 4db356924a ("xhci: turn cancelled td cleanup to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6599b6a6fa8060145046d0744456b6abdb3122a7 upstream.
The stream contex type (SCT) bitfield is used both in the stream context
data structure, and in the 'Set TR Dequeue pointer' command TRB.
In both cases it uses bits 3:1
The SCT_FOR_TRB(p) macro used to set the stream context type (SCT) field
for the 'Set TR Dequeue pointer' command TRB incorrectly shifts the value
1 bit left before masking the three bits.
Fix this by first masking and rshifting, just like the similar
SCT_FOR_CTX(p) macro does
This issue has not been visibile as the lost bit 3 is only used with
secondary stream arrays (SSA). Xhci driver currently only supports using
a primary stream array with Linear stream addressing.
Fixes: 95241dbdf8 ("xhci: Set SCT field for Set TR dequeue on streams")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241016140000.783905-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d381137cb6ecf558ef6698c7730ddd482d4c8f2 upstream.
If USB virtualizatoin is enabled, USB2 ports are shared between all
Virtual Functions. The USB2 port number owned by an USB2 root hub in
a Virtual Function may be less than total USB2 phy number supported
by the Tegra XUSB controller.
Using total USB2 phy number as port number to check all PORTSC values
would cause invalid memory access.
[ 116.923438] Unable to handle kernel paging request at virtual address 006c622f7665642f
...
[ 117.213640] Call trace:
[ 117.216783] tegra_xusb_enter_elpg+0x23c/0x658
[ 117.222021] tegra_xusb_runtime_suspend+0x40/0x68
[ 117.227260] pm_generic_runtime_suspend+0x30/0x50
[ 117.232847] __rpm_callback+0x84/0x3c0
[ 117.237038] rpm_suspend+0x2dc/0x740
[ 117.241229] pm_runtime_work+0xa0/0xb8
[ 117.245769] process_scheduled_works+0x24c/0x478
[ 117.251007] worker_thread+0x23c/0x328
[ 117.255547] kthread+0x104/0x1b0
[ 117.259389] ret_from_fork+0x10/0x20
[ 117.263582] Code: 54000222 f9461ae8 f8747908 b4ffff48 (f9400100)
Cc: stable@vger.kernel.org # v6.3+
Fixes: a30951d31b ("xhci: tegra: USB2 pad power controls")
Signed-off-by: Henry Lin <henryl@nvidia.com>
Link: https://lore.kernel.org/r/20241014042134.27664-1-henryl@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1dda2acc4192d826e84008d963b528e24d12bc upstream.
Fake CSR controllers don't seem to handle short-transfer properly which
cause command to time out:
kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd
kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91
kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
kernel: usb 1-1: Product: BT DONGLE10
...
Bluetooth: hci1: Opcode 0x1004 failed: -110
kernel: Bluetooth: hci1: command 0x1004 tx timeout
According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size
Constraints a interrupt transfer is considered complete when the size is 0
(ZPL) or < wMaxPacketSize:
'When an interrupt transfer involves more data than can fit in one
data payload of the currently established maximum size, all data
payloads are required to be maximum-sized except for the last data
payload, which will contain the remaining data. An interrupt transfer
is complete when the endpoint does one of the following:
• Has transferred exactly the amount of data expected
• Transfers a packet with a payload size less than wMaxPacketSize or
transfers a zero-length packet'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365
Fixes: 7b05933340f4 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9b7b535ba192c6b77e6c15a4c82d853163eab8c upstream.
If bt_debugfs is not created successfully, which happens if either
CONFIG_DEBUG_FS or CONFIG_DEBUG_FS_ALLOW_ALL is unset, then iso_init()
returns early and does not set iso_inited to true. This means that a
subsequent call to iso_init() will result in duplicate calls to
proto_register(), bt_sock_register(), etc.
With CONFIG_LIST_HARDENED and CONFIG_BUG_ON_DATA_CORRUPTION enabled, the
duplicate call to proto_register() triggers this BUG():
list_add double add: new=ffffffffc0b280d0, prev=ffffffffbab56250,
next=ffffffffc0b280d0.
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:35!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 2 PID: 887 Comm: bluetoothd Not tainted 6.10.11-1-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x9a/0xa0
...
__list_add_valid_or_report+0x9a/0xa0
proto_register+0x2b5/0x340
iso_init+0x23/0x150 [bluetooth]
set_iso_socket_func+0x68/0x1b0 [bluetooth]
kmem_cache_free+0x308/0x330
hci_sock_sendmsg+0x990/0x9e0 [bluetooth]
__sock_sendmsg+0x7b/0x80
sock_write_iter+0x9a/0x110
do_iter_readv_writev+0x11d/0x220
vfs_writev+0x180/0x3e0
do_writev+0xca/0x100
...
This change removes the early return. The check for iso_debugfs being
NULL was unnecessary, it is always NULL when iso_inited is false.
Cc: stable@vger.kernel.org
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d458cd1221e9e56da3b2cc5518ad3225caa91f20 upstream.
If iso_init() has been called, iso_exit() must be called on module
unload. Without that, the struct proto that iso_init() registered with
proto_register() becomes invalid, which could cause unpredictable
problems later. In my case, with CONFIG_LIST_HARDENED and
CONFIG_BUG_ON_DATA_CORRUPTION enabled, loading the module again usually
triggers this BUG():
list_add corruption. next->prev should be prev (ffffffffb5355fd0),
but was 0000000000000068. (next=ffffffffc0a010d0).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:29!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 4159 Comm: modprobe Not tainted 6.10.11-4+bt2-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x61/0xa0
...
__list_add_valid_or_report+0x61/0xa0
proto_register+0x299/0x320
hci_sock_init+0x16/0xc0 [bluetooth]
bt_init+0x68/0xd0 [bluetooth]
__pfx_bt_init+0x10/0x10 [bluetooth]
do_one_initcall+0x80/0x2f0
do_init_module+0x8b/0x230
__do_sys_init_module+0x15f/0x190
do_syscall_64+0x68/0x110
...
Cc: stable@vger.kernel.org
Fixes: ccf74f2390 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 530688e39c644543b71bdd9cb45fdfb458a28eaa upstream.
The opt3001 driver uses predetermined full-scale range values to
determine what exponent to use for event trigger threshold values.
The problem is that one of the values specified in the datasheet is
missing from the implementation. This causes larger values to be
scaled down to an incorrect exponent, effectively reducing the
maximum settable threshold value by a factor of 2.
Add missing full-scale range array value.
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Signed-off-by: Emil Gedenryd <emil.gedenryd@axis.com>
Cc: <Stable@vger.kernel.org>
Link: https://patch.msgid.link/20240913-add_opt3002-v2-1-69e04f840360@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7c44e57750c31de43906d97813273fdffcf7d02 upstream.
The dev pointer that is received as an argument in the
in_illuminance_period_available_show function references the device
embedded in the IIO device, not in the i2c client.
dev_to_iio_dev() must be used to accessthe right data. The current
implementation leads to a segmentation fault on every attempt to read
the attribute because indio_dev gets a NULL assignment.
This bug has been present since the first appearance of the driver,
apparently since the last version (V6) before getting applied. A
constant attribute was used until then, and the last modifications might
have not been tested again.
Cc: stable@vger.kernel.org
Fixes: 7b779f573c ("iio: light: add driver for veml6030 ambient light sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240913-veml6035-v1-3-0b09c0c90418@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9e9746f275c45108f2b0633a4855d65d9ae0736 upstream.
The driver still uses the sensor resolution provided in the datasheet
until Rev. 1.6, 28-Apr-2022, which was updated with Rev 1.7,
28-Nov-2023. The original ambient light resolution has been updated from
0.0036 lx/ct to 0.0042 lx/ct, which is the value that can be found in
the current device datasheet.
Update the default resolution for IT = 100 ms and GAIN = 1/8 from the
original 4608 mlux/cnt to the current value from the "Resolution and
maximum detection range" table (Application Note 84367, page 5), 5376
mlux/cnt.
Cc: <stable@vger.kernel.org>
Fixes: 7b779f573c ("iio: light: add driver for veml6030 ambient light sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20240923-veml6035-v2-1-58c72a0df31c@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0ec082f10b7a1fd25e8c1e2a686440da913b7a3 upstream.
Before this patch, if multiple BO_HANDLES chunks were submitted,
the error -EINVAL would be correctly set but could be overwritten
by the return value from amdgpu_cs_p1_bo_handles(). This patch
ensures that if there are multiple BO_HANDLES, we stop.
Fixes: fec5f8e8c6bc ("drm/amdgpu: disallow multiple BO_HANDLES chunks in one submit")
Signed-off-by: Mohammed Anees <pvmohammedanees2003@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 40f2cd98828f454bdc5006ad3d94330a5ea164b7)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28127dba64d8ae1a0b737b973d6d029908599611 upstream.
Include the encoder itself in its possible_clones bitmask.
In the past nothing validated that drivers were populating
possible_clones correctly, but that changed in commit
74d2aacbe8 ("drm: Validate encoder->possible_clones").
Looks like radeon never got the memo and is still not
following the rules 100% correctly.
This results in some warnings during driver initialization:
Bogus possible_clones: [ENCODER:46:TV-46] possible_clones=0x4 (full encoder mask=0x7)
WARNING: CPU: 0 PID: 170 at drivers/gpu/drm/drm_mode_config.c:615 drm_mode_config_validate+0x113/0x39c
...
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Fixes: 74d2aacbe8 ("drm: Validate encoder->possible_clones")
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Closes: https://lore.kernel.org/dri-devel/20241009000321.418e4294@yea/
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3b6e7d40649c0d75572039aff9d0911864c689db)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe05c40ca9c18cfdb003f639a30fc78a7ab49519 upstream.
Commit 160c826b4dd0 ("selftest: hid: add missing run-hid-tools-tests.sh")
has added the run-hid-tools-tests.sh script for it to be installed, but
I forgot to add the tests directory together.
If running the test case without the tests directory, will results in
the following error message:
make -C tools/testing/selftests/ TARGETS=hid install \
INSTALL_PATH=$KSFT_INSTALL_PATH
cd $KSFT_INSTALL_PATH
./run_kselftest.sh -t hid:hid-core.sh
/usr/lib/python3.11/site-packages/_pytest/config/__init__.py:331: PluggyTeardownRaisedWarning: A plugin raised an exception during an old-style hookwrapper teardown.
Plugin: helpconfig, Hook: pytest_cmdline_parse
UsageError: usage: __main__.py [options] [file_or_dir] [file_or_dir] [...]
__main__.py: error: unrecognized arguments: --udevd
inifile: None
rootdir: /root/linux/kselftest_install/hid
In fact, the run-hid-tools-tests.sh script uses the scripts in the tests
directory to run tests. The tests directory also needs to be added to be
installed.
Fixes: ffb85d5c9e ("selftests: hid: import hid-tools hid-core tests")
Cc: stable@vger.kernel.org
Signed-off-by: Yun Lu <luyun@kylinos.cn>
Acked-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
