commit fd70466d37 upstream.
Commit 52cf93e63e ("HID: i2c-hid: Don't reset device upon system
resume") fixes many touchpads and touchscreens, however ALPS touchpads
start to trigger IRQ storm after system resume.
Since it's total silence from ALPS, let's bring the old behavior back
to ALPS touchpads.
Fixes: 52cf93e63e ("HID: i2c-hid: Don't reset device upon system resume")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 076265907c upstream.
When presented with large amounts of memory being hotplugged
(in my test case, ~890GB), the call to flush_dcache_range takes
a while (~50 seconds), triggering RCU stalls.
This patch breaks up the call into 1GB chunks, calling
cond_resched() inbetween to allow the scheduler to run.
Fixes: fb5924fddf ("powerpc/mm: Flush cache on memory hot(un)plug")
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191104023305.9581-6-alastair@au1.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e73e92b15 upstream.
When running an nfs stress test, I see quite a few cached replies that
don't match up with the actual request. The first comment in
replay_matches_cache() makes sense, but the code doesn't seem to
match... fix it.
This isn't exactly a bugfix, as the server isn't required to catch every
case of a false retry. So, we may as well do this, but if this is
fixing a problem then that suggests there's a client bug.
Fixes: 53da6a53e1 ("nfsd4: catch some false session retries")
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40dd23f9a upstream.
The retention idle state does not appear to be supported by the firmware
present on the msm8998 laptops since the state is advertised as disabled
in ACPI, and attempting to enable the state in DT is observed to result
in boot hangs. Therefore, remove the state from use to address the
observed issues.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: 2c6d2d3a58 (arm64: dts: qcom: Add Lenovo Miix 630)
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fcaf6982d upstream.
I was investigating a crash in our Virtuozzo7 kernel which happened in
in svcauth_unix_set_client. I found out that we access m_client field
in ip_map structure, which was received from sunrpc_cache_lookup (we
have a bit older kernel, now the code is in sunrpc_cache_add_entry), and
these field looks uninitialized (m_client == 0x74 don't look like a
pointer) but in the cache_head in flags we see 0x1 which is CACHE_VALID.
It looks like the problem appeared from our previous fix to sunrpc (1):
commit 4ecd55ea07 ("sunrpc: fix cache_head leak due to queued
request")
And we've also found a patch already fixing our patch (2):
commit d58431eacb ("sunrpc: don't mark uninitialised items as VALID.")
Though the crash is eliminated, I think the core of the problem is not
completely fixed:
Neil in the patch (2) makes cache_head CACHE_NEGATIVE, before
cache_fresh_locked which was added in (1) to fix crash. These way
cache_is_valid won't say the cache is valid anymore and in
svcauth_unix_set_client the function cache_check will return error
instead of 0, and we don't count entry as initialized.
But it looks like we need to remove cache_fresh_locked completely in
sunrpc_cache_lookup:
In (1) we've only wanted to make cache_fresh_unlocked->cache_dequeue so
that cache_requests with no readers also release corresponding
cache_head, to fix their leak. We with Vasily were not sure if
cache_fresh_locked and cache_fresh_unlocked should be used in pair or
not, so we've guessed to use them in pair.
Now we see that we don't want the CACHE_VALID bit set here by
cache_fresh_locked, as "valid" means "initialized" and there is no
initialization in sunrpc_cache_add_entry. Both expiry_time and
last_refresh are not used in cache_fresh_unlocked code-path and also not
required for the initial fix.
So to conclude cache_fresh_locked was called by mistake, and we can just
safely remove it instead of crutching it with CACHE_NEGATIVE. It looks
ideologically better for me. Hope I don't miss something here.
Here is our crash backtrace:
[13108726.326291] BUG: unable to handle kernel NULL pointer dereference at 0000000000000074
[13108726.326365] IP: [<ffffffffc01f79eb>] svcauth_unix_set_client+0x2ab/0x520 [sunrpc]
[13108726.326448] PGD 0
[13108726.326468] Oops: 0002 [#1] SMP
[13108726.326497] Modules linked in: nbd isofs xfs loop kpatch_cumulative_81_0_r1(O) xt_physdev nfnetlink_queue bluetooth rfkill ip6table_nat nf_nat_ipv6 ip_vs_wrr ip_vs_wlc ip_vs_sh nf_conntrack_netlink ip_vs_sed ip_vs_pe_sip nf_conntrack_sip ip_vs_nq ip_vs_lc ip_vs_lblcr ip_vs_lblc ip_vs_ftp ip_vs_dh nf_nat_ftp nf_conntrack_ftp iptable_raw xt_recent nf_log_ipv6 xt_hl ip6t_rt nf_log_ipv4 nf_log_common xt_LOG xt_limit xt_TCPMSS xt_tcpmss vxlan ip6_udp_tunnel udp_tunnel xt_statistic xt_NFLOG nfnetlink_log dummy xt_mark xt_REDIRECT nf_nat_redirect raw_diag udp_diag tcp_diag inet_diag netlink_diag af_packet_diag unix_diag rpcsec_gss_krb5 xt_addrtype ip6t_rpfilter ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 ebtable_nat ebtable_broute nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_mangle ip6table_raw nfsv4
[13108726.327173] dns_resolver cls_u32 binfmt_misc arptable_filter arp_tables ip6table_filter ip6_tables devlink fuse_kio_pcs ipt_MASQUERADE nf_nat_masquerade_ipv4 xt_nat iptable_nat nf_nat_ipv4 xt_comment nf_conntrack_ipv4 nf_defrag_ipv4 xt_wdog_tmo xt_multiport bonding xt_set xt_conntrack iptable_filter iptable_mangle kpatch(O) ebtable_filter ebt_among ebtables ip_set_hash_ip ip_set nfnetlink vfat fat skx_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass fuse pcspkr ses enclosure joydev sg mei_me hpwdt hpilo lpc_ich mei ipmi_si shpchp ipmi_devintf ipmi_msghandler xt_ipvs acpi_power_meter ip_vs_rr nfsv3 nfsd auth_rpcgss nfs_acl nfs lockd grace fscache nf_nat cls_fw sch_htb sch_cbq sch_sfq ip_vs em_u32 nf_conntrack tun br_netfilter veth overlay ip6_vzprivnet ip6_vznetstat ip_vznetstat
[13108726.327817] ip_vzprivnet vziolimit vzevent vzlist vzstat vznetstat vznetdev vzmon vzdev bridge pio_kaio pio_nfs pio_direct pfmt_raw pfmt_ploop1 ploop ip_tables ext4 mbcache jbd2 sd_mod crc_t10dif crct10dif_generic mgag200 i2c_algo_bit drm_kms_helper scsi_transport_iscsi 8021q syscopyarea sysfillrect garp sysimgblt fb_sys_fops mrp stp ttm llc bnx2x crct10dif_pclmul crct10dif_common crc32_pclmul crc32c_intel drm dm_multipath ghash_clmulni_intel uas aesni_intel lrw gf128mul glue_helper ablk_helper cryptd tg3 smartpqi scsi_transport_sas mdio libcrc32c i2c_core usb_storage ptp pps_core wmi sunrpc dm_mirror dm_region_hash dm_log dm_mod [last unloaded: kpatch_cumulative_82_0_r1]
[13108726.328403] CPU: 35 PID: 63742 Comm: nfsd ve: 51332 Kdump: loaded Tainted: G W O ------------ 3.10.0-862.20.2.vz7.73.29 #1 73.29
[13108726.328491] Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 10/02/2018
[13108726.328554] task: ffffa0a6a41b1160 ti: ffffa0c2a74bc000 task.ti: ffffa0c2a74bc000
[13108726.328610] RIP: 0010:[<ffffffffc01f79eb>] [<ffffffffc01f79eb>] svcauth_unix_set_client+0x2ab/0x520 [sunrpc]
[13108726.328706] RSP: 0018:ffffa0c2a74bfd80 EFLAGS: 00010246
[13108726.328750] RAX: 0000000000000001 RBX: ffffa0a6183ae000 RCX: 0000000000000000
[13108726.328811] RDX: 0000000000000074 RSI: 0000000000000286 RDI: ffffa0c2a74bfcf0
[13108726.328864] RBP: ffffa0c2a74bfe00 R08: ffffa0bab8c22960 R09: 0000000000000001
[13108726.328916] R10: 0000000000000001 R11: 0000000000000001 R12: ffffa0a32aa7f000
[13108726.328969] R13: ffffa0a6183afac0 R14: ffffa0c233d88d00 R15: ffffa0c2a74bfdb4
[13108726.329022] FS: 0000000000000000(0000) GS:ffffa0e17f9c0000(0000) knlGS:0000000000000000
[13108726.329081] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[13108726.332311] CR2: 0000000000000074 CR3: 00000026a1b28000 CR4: 00000000007607e0
[13108726.334606] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[13108726.336754] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[13108726.338908] PKRU: 00000000
[13108726.341047] Call Trace:
[13108726.343074] [<ffffffff8a2c78b4>] ? groups_alloc+0x34/0x110
[13108726.344837] [<ffffffffc01f5eb4>] svc_set_client+0x24/0x30 [sunrpc]
[13108726.346631] [<ffffffffc01f2ac1>] svc_process_common+0x241/0x710 [sunrpc]
[13108726.348332] [<ffffffffc01f3093>] svc_process+0x103/0x190 [sunrpc]
[13108726.350016] [<ffffffffc07d605f>] nfsd+0xdf/0x150 [nfsd]
[13108726.351735] [<ffffffffc07d5f80>] ? nfsd_destroy+0x80/0x80 [nfsd]
[13108726.353459] [<ffffffff8a2bf741>] kthread+0xd1/0xe0
[13108726.355195] [<ffffffff8a2bf670>] ? create_kthread+0x60/0x60
[13108726.356896] [<ffffffff8a9556dd>] ret_from_fork_nospec_begin+0x7/0x21
[13108726.358577] [<ffffffff8a2bf670>] ? create_kthread+0x60/0x60
[13108726.360240] Code: 4c 8b 45 98 0f 8e 2e 01 00 00 83 f8 fe 0f 84 76 fe ff ff 85 c0 0f 85 2b 01 00 00 49 8b 50 40 b8 01 00 00 00 48 89 93 d0 1a 00 00 <f0> 0f c1 02 83 c0 01 83 f8 01 0f 8e 53 02 00 00 49 8b 44 24 38
[13108726.363769] RIP [<ffffffffc01f79eb>] svcauth_unix_set_client+0x2ab/0x520 [sunrpc]
[13108726.365530] RSP <ffffa0c2a74bfd80>
[13108726.367179] CR2: 0000000000000074
Fixes: d58431eacb ("sunrpc: don't mark uninitialised items as VALID.")
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70082a52f9 upstream.
Without this header file, compile-testing may run into a missing
declaration:
drivers/gpu/drm/msm/msm_gpu.c:444:4: error: implicit declaration of function 'put_task_struct' [-Werror,-Wimplicit-function-declaration]
Fixes: 482f96324a ("drm/msm: Fix task dump in gpu recovery")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca59d5a516 upstream.
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24cecc3774 upstream.
The ARMv8 64-bit architecture supports execute-only user permissions by
clearing the PTE_USER and PTE_UXN bits, practically making it a mostly
privileged mapping but from which user running at EL0 can still execute.
The downside, however, is that the kernel at EL1 inadvertently reading
such mapping would not trip over the PAN (privileged access never)
protection.
Revert the relevant bits from commit cab15ce604 ("arm64: Introduce
execute-only page access permissions") so that PROT_EXEC implies
PROT_READ (and therefore PTE_USER) until the architecture gains proper
support for execute-only user mappings.
Fixes: cab15ce604 ("arm64: Introduce execute-only page access permissions")
Cc: <stable@vger.kernel.org> # 4.9.x-
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43cf75d964 upstream.
Currently, when global init and all threads in its thread-group have exited
we panic via:
do_exit()
-> exit_notify()
-> forget_original_parent()
-> find_child_reaper()
This makes it hard to extract a useable coredump for global init from a
kernel crashdump because by the time we panic exit_mm() will have already
released global init's mm.
This patch moves the panic futher up before exit_mm() is called. As was the
case previously, we only panic when global init and all its threads in the
thread-group have exited.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
[christian.brauner@ubuntu.com: fix typo, rewrite commit message]
Link: https://lore.kernel.org/r/1576736993-10121-1-git-send-email-qiwuchen55@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97acd0019d upstream.
A prior use-after-free mailbox fix solved it's problem by null'ing a ndlp
pointer. However, further testing has shown that this change causes a
later state change to occasionally be skipped, which results in a reference
count never being decremented thus the rpi is never released, which causes
a vport delete to never succeed.
Revise the fix in the prior patch to no longer null the ndlp. Instead the
RELEASE_RPI flag is set which will drive the release of the rpi.
Given the new code was added at a deep indentation level, refactor the code
block using a new routine that avoids the indentation issues.
Fixes: 9b16406864 ("scsi: lpfc: Fix use-after-free mailbox cmd completion")
Link: https://lore.kernel.org/r/20190922035906.10977-6-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2406ff9b86 upstream.
For non-x86 architectures, SNDRV_DMA_TYPE_DEV_UC should be treated
equivalent with SNDRV_DMA_TYPE_DEV, where the default mmap handler
still checks only about SNDRV_DMA_TYPE_DEV. Make the check more
proper.
Note that all existing users of *_UC buffer types are x86-only, so
this doesn't fix any bug, but just for consistency.
Fixes: 42e748a0b3 ("ALSA: memalloc: Add non-cached buffer type")
Link: https://lore.kernel.org/r/20191108165626.5947-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d60229d848 upstream.
The return from pnp_irq is an unsigned integer type resource_size_t
and hence the error check for a positive non-error code is always
going to be true. A check for a non-failure return from pnp_irq
should in fact be for (resource_size_t)-1 rather than >= 0.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: a9824c868a ("[ALSA] Add CS4232 PnP BIOS support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191122131354.58042-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc976614f5 upstream.
Prior to commit 858805b336 ("kbuild: add $(BASH) to run scripts with
bash-extension"), this shell script was almost always run by bash since
bash is usually installed on the system by default.
Now, this script is run by sh, which might be a symlink to dash. On such
distributions, the following code emits an error:
local dev=`LC_ALL=C ls -l "${location}"`
You can reproduce the build error, for example by setting
CONFIG_INITRAMFS_SOURCE="/dev".
GEN usr/initramfs_data.cpio.gz
./usr/gen_initramfs_list.sh: 131: local: 1: bad variable name
make[1]: *** [usr/Makefile:61: usr/initramfs_data.cpio.gz] Error 2
This is because `LC_ALL=C ls -l "${location}"` contains spaces.
Surrounding it with double-quotes fixes the error.
Fixes: 858805b336 ("kbuild: add $(BASH) to run scripts with bash-extension")
Reported-by: Jory A. Pratt <anarchy@gentoo.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c62ed27a1 upstream.
aa_xattrs_match() is unfortunately calling vfs_getxattr_alloc() from a
context protected by an rcu_read_lock. This can not be done as
vfs_getxattr_alloc() may sleep regardles of the gfp_t value being
passed to it.
Fix this by breaking the rcu_read_lock on the policy search when the
xattr match feature is requested and restarting the search if a policy
changes occur.
Fixes: 8e51f9087f ("apparmor: Add support for attaching profiles via xattr, presence and value")
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01f36a554e upstream.
trace_printk schedules work via irq_work_queue(), but doesn't
wait until it was processed. The kprobe_module.tc testcase does:
:;: "Load module again, which means the event1 should be recorded";:
modprobe trace-printk
grep "event1:" trace
so the grep which checks the trace file might run before the irq work
was processed. Fix this by adding a irq_work_sync().
Link: http://lore.kernel.org/linux-trace-devel/20191218074427.96184-3-svens@linux.ibm.com
Cc: stable@vger.kernel.org
Fixes: af2a0750f3 ("selftests/ftrace: Improve kprobe on module testcase to load/unload module")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 106f41f5a3 upstream.
The compare functions of the histogram code would be specific for the size
of the value being compared (byte, short, int, long long). It would
reference the value from the array via the type of the compare, but the
value was stored in a 64 bit number. This is fine for little endian
machines, but for big endian machines, it would end up comparing zeros or
all ones (depending on the sign) for anything but 64 bit numbers.
To fix this, first derference the value as a u64 then convert it to the type
being compared.
Link: http://lkml.kernel.org/r/20191211103557.7bed6928@gandalf.local.home
Cc: stable@vger.kernel.org
Fixes: 08d43a5fa0 ("tracing: Add lock-free tracing_map")
Acked-by: Tom Zanussi <zanussi@kernel.org>
Reported-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 256efaea1f upstream.
gpiolib has a corner case with open drain outputs that are emulated.
When such outputs are outputting a logic 1, emulation will set the
hardware to input mode, which will cause gpiod_get_direction() to
report that it is in input mode. This is different from the behaviour
with a true open-drain output.
Unify the semantics here.
Cc: <stable@vger.kernel.org>
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 634f0348fe upstream.
Commit cad6fade6e ("xtensa: clean up WSR*/RSR*/get_sr/set_sr") removed
{RSR,WSR}_CPENABLE from xtensa code, but did not fix up all users,
breaking gpio-xtensa driver build. Update gpio-xtensa to use
new xtensa_{get,set}_sr API.
Cc: stable@vger.kernel.org # v5.0+
Fixes: cad6fade6e ("xtensa: clean up WSR*/RSR*/get_sr/set_sr")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8385d756e1 upstream.
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c4036 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit 1a3d78cb6e upstream.
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf0e5013bc upstream.
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae2 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0cdf2ac4b upstream.
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f8297 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84b032dbfd upstream.
This reverts commit 6bb86fefa0
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f54c7898ed upstream.
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes. Upon closer analysis, it turns out that precise scalar
value tracking is missing a few precision markings for unknown scalars:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 0
1: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (35) if r0 >= 0xf72e goto pc+0
--> only follow fallthrough
2: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
2: (35) if r0 >= 0x80fe0000 goto pc+0
--> only follow fallthrough
3: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
3: (14) w0 -= -536870912
4: R0_w=invP536870912 R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (0f) r1 += r0
5: R0_w=invP536870912 R1_w=inv(id=0) R10=fp0
5: (55) if r1 != 0x104c1500 goto pc+0
--> push other branch for later analysis
R0_w=invP536870912 R1_w=inv273421568 R10=fp0
6: R0_w=invP536870912 R1_w=inv273421568 R10=fp0
6: (b7) r0 = 0
7: R0=invP0 R1=inv273421568 R10=fp0
7: (76) if w1 s>= 0xffffff00 goto pc+3
--> only follow goto
11: R0=invP0 R1=inv273421568 R10=fp0
11: (95) exit
6: R0_w=invP536870912 R1_w=inv(id=0) R10=fp0
6: (b7) r0 = 0
propagating r0
7: safe
processed 11 insns [...]
In the analysis of the second path coming after the successful exit above,
the path is being pruned at line 7. Pruning analysis found that both r0 are
precise P0 and both R1 are non-precise scalars and given prior path with
R1 as non-precise scalar succeeded, this one is therefore safe as well.
However, problem is that given condition at insn 7 in the first run, we only
followed goto and didn't push the other branch for later analysis, we've
never walked the few insns in there and therefore dead-code sanitation
rewrites it as goto pc-1, causing the hang depending on the skb address
hitting these conditions. The issue is that R1 should have been marked as
precise as well such that pruning enforces range check and conluded that new
R1 is not in range of old R1. In insn 4, we mark R1 (skb) as unknown scalar
via __mark_reg_unbounded() but not mark_reg_unbounded() and therefore
regs->precise remains as false.
Back in b5dc0163d8 ("bpf: precise scalar_value tracking"), this was not
the case since marking out of __mark_reg_unbounded() had this covered as well.
Once in both are set as precise in 4 as they should have been, we conclude
that given R1 was in prior fall-through path 0x104c1500 and now is completely
unknown, the check at insn 7 concludes that we need to continue walking.
Analysis after the fix:
0: R1=ctx(id=0,off=0,imm=0) R10=fp0
0: (b7) r0 = 0
1: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
1: (35) if r0 >= 0xf72e goto pc+0
2: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
2: (35) if r0 >= 0x80fe0000 goto pc+0
3: R0_w=invP0 R1=ctx(id=0,off=0,imm=0) R10=fp0
3: (14) w0 -= -536870912
4: R0_w=invP536870912 R1=ctx(id=0,off=0,imm=0) R10=fp0
4: (0f) r1 += r0
5: R0_w=invP536870912 R1_w=invP(id=0) R10=fp0
5: (55) if r1 != 0x104c1500 goto pc+0
R0_w=invP536870912 R1_w=invP273421568 R10=fp0
6: R0_w=invP536870912 R1_w=invP273421568 R10=fp0
6: (b7) r0 = 0
7: R0=invP0 R1=invP273421568 R10=fp0
7: (76) if w1 s>= 0xffffff00 goto pc+3
11: R0=invP0 R1=invP273421568 R10=fp0
11: (95) exit
6: R0_w=invP536870912 R1_w=invP(id=0) R10=fp0
6: (b7) r0 = 0
7: R0_w=invP0 R1_w=invP(id=0) R10=fp0
7: (76) if w1 s>= 0xffffff00 goto pc+3
R0_w=invP0 R1_w=invP(id=0) R10=fp0
8: R0_w=invP0 R1_w=invP(id=0) R10=fp0
8: (a5) if r0 < 0x2007002a goto pc+0
9: R0_w=invP0 R1_w=invP(id=0) R10=fp0
9: (57) r0 &= -16316416
10: R0_w=invP0 R1_w=invP(id=0) R10=fp0
10: (a6) if w0 < 0x1201 goto pc+0
11: R0_w=invP0 R1_w=invP(id=0) R10=fp0
11: (95) exit
11: R0=invP0 R1=invP(id=0) R10=fp0
11: (95) exit
processed 16 insns [...]
Fixes: 6754172c20 ("bpf: fix precision tracking in presence of bpf2bpf calls")
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191222223740.25297-1-daniel@iogearbox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2c0fcd287 upstream.
These were added to blkdev_ioctl() in linux-5.5 but not
blkdev_compat_ioctl, so add them now.
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: bbd3e06436 ("block: add an API for Persistent Reservations")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fold in followup patch from Arnd with missing pr.h header include.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit de7999afed upstream.
When starting writeback for a range that covers part of a preallocated
extent, due to a race with writeback for another range that also covers
another part of the same preallocated extent, we can end up in an infinite
loop.
Consider the following example where for inode 280 we have two dirty
ranges:
range A, from 294912 to 303103, 8192 bytes
range B, from 348160 to 438271, 90112 bytes
and we have the following file extent item layout for our inode:
leaf 38895616 gen 24544 total ptrs 29 free space 13820 owner 5
(...)
item 27 key (280 108 200704) itemoff 14598 itemsize 53
extent data disk bytenr 0 nr 0 type 1 (regular)
extent data offset 0 nr 94208 ram 94208
item 28 key (280 108 294912) itemoff 14545 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 2 (prealloc)
extent data offset 0 nr 81920 ram 81920
Then the following happens:
1) Writeback starts for range B (from 348160 to 438271), execution of
run_delalloc_nocow() starts;
2) The first iteration of run_delalloc_nocow()'s whil loop leaves us at
the extent item at slot 28, pointing to the prealloc extent item
covering the range from 294912 to 376831. This extent covers part of
our range;
3) An ordered extent is created against that extent, covering the file
range from 348160 to 376831 (28672 bytes);
4) We adjust 'cur_offset' to 376832 and move on to the next iteration of
the while loop;
5) The call to btrfs_lookup_file_extent() leaves us at the same leaf,
pointing to slot 29, 1 slot after the last item (the extent item
we processed in the previous iteration);
6) Because we are a slot beyond the last item, we call btrfs_next_leaf(),
which releases the search path before doing a another search for the
last key of the leaf (280 108 294912);
7) Right after btrfs_next_leaf() released the path, and before it did
another search for the last key of the leaf, writeback for the range
A (from 294912 to 303103) completes (it was previously started at
some point);
8) Upon completion of the ordered extent for range A, the prealloc extent
we previously found got split into two extent items, one covering the
range from 294912 to 303103 (8192 bytes), with a type of regular extent
(and no longer prealloc) and another covering the range from 303104 to
376831 (73728 bytes), with a type of prealloc and an offset of 8192
bytes. So our leaf now has the following layout:
leaf 38895616 gen 24544 total ptrs 31 free space 13664 owner 5
(...)
item 27 key (280 108 200704) itemoff 14598 itemsize 53
extent data disk bytenr 0 nr 0 type 1
extent data offset 0 nr 8192 ram 94208
item 28 key (280 108 208896) itemoff 14545 itemsize 53
extent data disk bytenr 10433142784 nr 86016 type 1
extent data offset 0 nr 86016 ram 86016
item 29 key (280 108 294912) itemoff 14492 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 1
extent data offset 0 nr 8192 ram 81920
item 30 key (280 108 303104) itemoff 14439 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 2
extent data offset 8192 nr 73728 ram 81920
9) After btrfs_next_leaf() returns, we have our path pointing to that same
leaf and at slot 30, since it has a key we didn't have before and it's
the first key greater then the key that was previously the last key of
the leaf (key (280 108 294912));
10) The extent item at slot 30 covers the range from 303104 to 376831
which is in our target range, so we process it, despite having already
created an ordered extent against this extent for the file range from
348160 to 376831. This is because we skip to the next extent item only
if its end is less than or equals to the start of our delalloc range,
and not less than or equals to the current offset ('cur_offset');
11) As a result we compute 'num_bytes' as:
num_bytes = min(end + 1, extent_end) - cur_offset;
= min(438271 + 1, 376832) - 376832 = 0
12) We then call create_io_em() for a 0 bytes range starting at offset
376832;
13) Then create_io_em() enters an infinite loop because its calls to
btrfs_drop_extent_cache() do nothing due to the 0 length range
passed to it. So no existing extent maps that cover the offset
376832 get removed, and therefore calls to add_extent_mapping()
return -EEXIST, resulting in an infinite loop. This loop from
create_io_em() is the following:
do {
btrfs_drop_extent_cache(BTRFS_I(inode), em->start,
em->start + em->len - 1, 0);
write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em, 1);
write_unlock(&em_tree->lock);
/*
* The caller has taken lock_extent(), who could race with us
* to add em?
*/
} while (ret == -EEXIST);
Also, each call to btrfs_drop_extent_cache() triggers a warning because
the start offset passed to it (376832) is smaller then the end offset
(376832 - 1) passed to it by -1, due to the 0 length:
[258532.052621] ------------[ cut here ]------------
[258532.052643] WARNING: CPU: 0 PID: 9987 at fs/btrfs/file.c:602 btrfs_drop_extent_cache+0x3f4/0x590 [btrfs]
(...)
[258532.052672] CPU: 0 PID: 9987 Comm: fsx Tainted: G W 5.4.0-rc7-btrfs-next-64 #1
[258532.052673] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
[258532.052691] RIP: 0010:btrfs_drop_extent_cache+0x3f4/0x590 [btrfs]
(...)
[258532.052695] RSP: 0018:ffffb4be0153f860 EFLAGS: 00010287
[258532.052700] RAX: ffff975b445ee360 RBX: ffff975b44eb3e08 RCX: 0000000000000000
[258532.052700] RDX: 0000000000038fff RSI: 0000000000039000 RDI: ffff975b445ee308
[258532.052700] RBP: 0000000000038fff R08: 0000000000000000 R09: 0000000000000001
[258532.052701] R10: ffff975b513c5c10 R11: 00000000e3c0cfa9 R12: 0000000000039000
[258532.052703] R13: ffff975b445ee360 R14: 00000000ffffffef R15: ffff975b445ee308
[258532.052705] FS: 00007f86a821de80(0000) GS:ffff975b76a00000(0000) knlGS:0000000000000000
[258532.052707] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[258532.052708] CR2: 00007fdacf0f3ab4 CR3: 00000001f9d26002 CR4: 00000000003606f0
[258532.052712] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[258532.052717] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[258532.052717] Call Trace:
[258532.052718] ? preempt_schedule_common+0x32/0x70
[258532.052722] ? ___preempt_schedule+0x16/0x20
[258532.052741] create_io_em+0xff/0x180 [btrfs]
[258532.052767] run_delalloc_nocow+0x942/0xb10 [btrfs]
[258532.052791] btrfs_run_delalloc_range+0x30b/0x520 [btrfs]
[258532.052812] ? find_lock_delalloc_range+0x221/0x250 [btrfs]
[258532.052834] writepage_delalloc+0xe4/0x140 [btrfs]
[258532.052855] __extent_writepage+0x110/0x4e0 [btrfs]
[258532.052876] extent_write_cache_pages+0x21c/0x480 [btrfs]
[258532.052906] extent_writepages+0x52/0xb0 [btrfs]
[258532.052911] do_writepages+0x23/0x80
[258532.052915] __filemap_fdatawrite_range+0xd2/0x110
[258532.052938] btrfs_fdatawrite_range+0x1b/0x50 [btrfs]
[258532.052954] start_ordered_ops+0x57/0xa0 [btrfs]
[258532.052973] ? btrfs_sync_file+0x225/0x490 [btrfs]
[258532.052988] btrfs_sync_file+0x225/0x490 [btrfs]
[258532.052997] __x64_sys_msync+0x199/0x200
[258532.053004] do_syscall_64+0x5c/0x250
[258532.053007] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[258532.053010] RIP: 0033:0x7f86a7dfd760
(...)
[258532.053014] RSP: 002b:00007ffd99af0368 EFLAGS: 00000246 ORIG_RAX: 000000000000001a
[258532.053016] RAX: ffffffffffffffda RBX: 0000000000000ec9 RCX: 00007f86a7dfd760
[258532.053017] RDX: 0000000000000004 RSI: 000000000000836c RDI: 00007f86a8221000
[258532.053019] RBP: 0000000000021ec9 R08: 0000000000000003 R09: 00007f86a812037c
[258532.053020] R10: 0000000000000001 R11: 0000000000000246 R12: 00000000000074a3
[258532.053021] R13: 00007f86a8221000 R14: 000000000000836c R15: 0000000000000001
[258532.053032] irq event stamp: 1653450494
[258532.053035] hardirqs last enabled at (1653450493): [<ffffffff9dec69f9>] _raw_spin_unlock_irq+0x29/0x50
[258532.053037] hardirqs last disabled at (1653450494): [<ffffffff9d4048ea>] trace_hardirqs_off_thunk+0x1a/0x20
[258532.053039] softirqs last enabled at (1653449852): [<ffffffff9e200466>] __do_softirq+0x466/0x6bd
[258532.053042] softirqs last disabled at (1653449845): [<ffffffff9d4c8a0c>] irq_exit+0xec/0x120
[258532.053043] ---[ end trace 8476fce13d9ce20a ]---
Which results in flooding dmesg/syslog since btrfs_drop_extent_cache()
uses WARN_ON() and not WARN_ON_ONCE().
So fix this issue by changing run_delalloc_nocow()'s loop to move to the
next extent item when the current extent item ends at at offset less than
or equals to the current offset instead of the start offset.
Fixes: 80ff385665 ("Btrfs: update nodatacow code v2")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a256a9b9 upstream.
dmaengine_desc_set_reuse() allocates a struct dma_slave_caps on the
stack, populates it using dma_get_slave_caps() and then accesses one
of its members.
However dma_get_slave_caps() may fail and this isn't accounted for,
leading to a legitimate warning of gcc-4.9 (but not newer versions):
In file included from drivers/spi/spi-bcm2835.c:19:0:
drivers/spi/spi-bcm2835.c: In function 'dmaengine_desc_set_reuse':
>> include/linux/dmaengine.h:1370:10: warning: 'caps.descriptor_reuse' is used uninitialized in this function [-Wuninitialized]
if (caps.descriptor_reuse) {
Fix it, thereby also silencing the gcc-4.9 warning.
The issue has been present for 4 years but surfaces only now that
the first caller of dmaengine_desc_set_reuse() has been added in
spi-bcm2835.c. Another user of reusable DMA descriptors has existed
for a while in pxa_camera.c, but it sets the DMA_CTRL_REUSE flag
directly instead of calling dmaengine_desc_set_reuse(). Nevertheless,
tag this commit for stable in case there are out-of-tree users.
Fixes: 272420214d ("dmaengine: Add DMA_CTRL_REUSE")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.3+
Link: https://lore.kernel.org/r/ca92998ccc054b4f2bfd60ef3adbab2913171eac.1575546234.git.lukas@wunner.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771b894f2f upstream.
The sizes by which seccomp_notif and seccomp_notif_resp are allocated are
based on the SECCOMP_GET_NOTIF_SIZES ioctl. This allows for graceful
extension of these datastructures. If userspace zeroes out the
datastructure based on its version, and it is lagging behind the kernel's
version, it will end up sending trailing garbage. On the other hand,
if it is ahead of the kernel version, it will write extra zero space,
and potentially cause corruption.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20191230203503.4925-1-sargun@sargun.me
Fixes: fec7b66905 ("samples: add an example of seccomp user trap")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5b0dc5a46 upstream.
I noticed that randconfig builds with gcc no longer produce a lot of
ccache hits, unlike with clang, and traced this back to plugins
now being enabled unconditionally if they are supported.
I am now working around this by adding
export CCACHE_COMPILERCHECK=/usr/bin/size -A %compiler%
to my top-level Makefile. This changes the heuristic that ccache uses
to determine whether the plugins are the same after a 'make clean'.
However, it also seems that being able to just turn off the plugins is
generally useful, at least for build testing it adds noticeable overhead
but does not find a lot of bugs additional bugs, and may be easier for
ccache users than my workaround.
Fixes: 9f671e5815 ("security: Create "kernel hardening" config area")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20191211133951.401933-1-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
