[ Upstream commit 90c6cb4a35 ]
Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.
In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.
Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2361ae5953 ]
SCSI LUN passthrough code such as qemu's "scsi-block" device model
pass every IO to the host via SG_IO ioctls. Currently, dm-multipath
calls choose_pgpath() only in the block IO code path, not in the ioctl
code path (unless current_pgpath is NULL). This has the effect that no
path switching and thus no load balancing is done for SCSI-passthrough
IO, unless the active path fails.
Fix this by using the same logic in multipath_prepare_ioctl() as in
multipath_clone_and_map().
Note: The allegedly best path selection algorithm, service-time,
still wouldn't work perfectly, because the io size of the current
request is always set to 0. Changing that for the IO passthrough
case would require the ioctl cmd and arg to be passed to dm's
prepare_ioctl() method.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b668c064e ]
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e47bd937e6 ]
The TOP 'aclk*_isp', 'aclk550_cam', 'gscl_wa' and 'gscl_wb' clocks must
be kept enabled all the time to allow proper access to power management
control for the ISP and CAM power domains. The last two clocks, although
related to GScaler device and GSCL power domain, provides also the
I_WRAP_CLK signal to MIPI CSIS0/1 devices, which are a part of CAM power
domain and are needed for proper power on/off sequence.
Currently there are no drivers for the devices, which are part of CAM and
ISP power domains yet. This patch only fixes the race between disabling
the unused power domains and disabling unused clocks, which randomly
resulted in the following error during boot:
Power domain CAM disable failed
Power domain ISP disable failed
Fixes: 318fa46cc6 ("clk/samsung: exynos542x: mark some clocks as critical")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e81c979f4e ]
If we timeout during a message transfer, the control register may
contain bits that cause an action to be set. Read-modify-writing the
register leaving these bits set may trigger the hardware to attempt
one of these actions unintentionally.
Always clear these bits when cleaning up after a message or after
a timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baaa7ebf25 ]
This reserved space isn't committed yet but cannot be used for
allocations. For userspace it has no difference from used space.
See the same fix in ext4 commit f06925c739 ("ext4: report delalloc
reserve as non-free in statfs for project quota").
Fixes: ddc34e328d ("f2fs: introduce f2fs_statfs_project")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dee2dabc0e ]
Limit the output of humidity compensation to the range between 0 and 100
percent.
Depending on the calibration parameters of the individual sensor it
happens, that a humidity above 100 percent or below 0 percent is
calculated, which don't make sense in terms of relative humidity.
Add a clamp to the compensation formula as described in the datasheet of
the sensor in chapter 4.2.3.
Although this clamp is documented, it was never in the driver of the
kernel.
It depends on the circumstances (calibration parameters, temperature,
humidity) if one can see a value above 100 percent without the clamp.
The writer of this patch was working with this type of sensor without
noting this error. So it seems to be a rare event when this bug occures.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d09ddd8190 ]
When resizing a BAR, pci_reassign_bridge_resources() is invoked to bring
the bridge windows of parent bridges in line with the new BAR assignment.
This assumes the device whose BAR is being resized lives on a subordinate
bus, but this is not necessarily the case. A device may live on the root
bus, in which case dev->bus->self is NULL, and passing a NULL pci_dev
pointer to pci_reassign_bridge_resources() will cause it to crash.
So let's make the call to pci_reassign_bridge_resources() conditional on
whether dev->bus->self is non-NULL in the first place.
Fixes: 8bb705e3e7 ("PCI: Add pci_resize_resource() for resizing BARs")
Link: https://lore.kernel.org/r/20200421162256.26887-1-ardb@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a4c0cfb4b ]
Smatch complains that the "path_data->handle" variable is user controlled.
It comes from iscsi_set_path() so that seems possible. It's harmless to
add a limit check.
The qedi->ep_tbl[] array has qedi->max_active_conns elements (which is
always ISCSI_MAX_SESS_PER_HBA (4096) elements). The array is allocated in
the qedi_cm_alloc_mem() function.
Link: https://lore.kernel.org/r/20200428131939.GA696531@mwanda
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2854bbe5f ]
The CMA and DMA_CMA Kconfig options need to be selected
by the Integrator in order to produce boot console on some
Integrator systems.
The REGULATOR and REGULATOR_FIXED_VOLTAGE need to be
selected in order to boot the system from an external
MMC card when using MMCI/PL181 from the device tree
probe path.
Select these things directly from the Kconfig so we are
sure to be able to bring the systems up with console
from any device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a697ae6ea5 ]
davinci_mcasp_get_dma_type() invokes dma_request_chan(), which returns a
reference of the specified dma_chan object to "chan" with increased
refcnt.
When davinci_mcasp_get_dma_type() returns, local variable "chan" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
davinci_mcasp_get_dma_type(). When chan device is NULL, the function
forgets to decrease the refcnt increased by dma_request_chan(), causing
a refcnt leak.
Fix this issue by calling dma_release_channel() when chan device is
NULL.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/1587818916-38730-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8207c155a ]
If probing the LP885x backlight fails after the regulators have been
enabled, then the following warning is seen when releasing the
regulators ...
WARNING: CPU: 1 PID: 289 at drivers/regulator/core.c:2051 _regulator_put.part.28+0x158/0x160
Modules linked in: tegra_xudc lp855x_bl(+) host1x pwm_tegra ip_tables x_tables ipv6 nf_defrag_ipv6
CPU: 1 PID: 289 Comm: systemd-udevd Not tainted 5.6.0-rc2-next-20200224 #1
Hardware name: NVIDIA Jetson TX1 Developer Kit (DT)
...
Call trace:
_regulator_put.part.28+0x158/0x160
regulator_put+0x34/0x50
devm_regulator_release+0x10/0x18
release_nodes+0x12c/0x230
devres_release_all+0x34/0x50
really_probe+0x1c0/0x370
driver_probe_device+0x58/0x100
device_driver_attach+0x6c/0x78
__driver_attach+0xb0/0xf0
bus_for_each_dev+0x68/0xc8
driver_attach+0x20/0x28
bus_add_driver+0x160/0x1f0
driver_register+0x60/0x110
i2c_register_driver+0x40/0x80
lp855x_driver_init+0x20/0x1000 [lp855x_bl]
do_one_initcall+0x58/0x1a0
do_init_module+0x54/0x1d0
load_module+0x1d80/0x21c8
__do_sys_finit_module+0xe8/0x100
__arm64_sys_finit_module+0x18/0x20
el0_svc_common.constprop.3+0xb0/0x168
do_el0_svc+0x20/0x98
el0_sync_handler+0xf4/0x1b0
el0_sync+0x140/0x180
Fix this by ensuring that the regulators are disabled, if enabled, on
probe failure.
Finally, ensure that the vddio regulator is disabled in the driver
remove handler.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f47ab3c2f5 ]
During the process of debugging a processor derived from the msm8916 which
we found the new processor was not starting one of its PLLs.
After tracing the addresses and writes that downstream was doing and
comparing to upstream it became obvious that we were writing to a different
register location than downstream when trying to configure the PLL.
This error is also present in upstream msm8916.
As an example clk-pll.c::clk_pll_recalc_rate wants to write to
pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
example
lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf
0x01823010 GCC_BIMC_PLL_USER_CTL
0x01823014 GCC_BIMC_PLL_CONFIG_CTL
This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.
This error is likely not apparent since the bootloader will already have
initialized these PLLs.
This patch corrects the location of config_reg from PLL_CONFIG_CTL to
PLL_USER_CTL for all relevant PLLs on msm8916.
Fixes commit 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6442df4940 ]
If ida_simple_get() returns an error when called in rproc_alloc(),
put_device() is called to clean things up. By this time the rproc
device type has been assigned, with rproc_type_release() as the
release function.
The first thing rproc_type_release() does is call:
idr_destroy(&rproc->notifyids);
But at the time the ida_simple_get() call is made, the notifyids
field in the remoteproc structure has not been initialized.
I'm not actually sure this case causes an observable problem, but
it's incorrect. Fix this by initializing the notifyids field before
calling ida_simple_get() in rproc_alloc().
Fixes: b5ab5e24e9 ("remoteproc: maintain a generic child device for each rproc")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200415204858.2448-2-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97b31a6f5f ]
With DEBUG_SHIRQ enabled we have a kernel crash
[ 116.482696] BUG: kernel NULL pointer dereference, address: 0000000000000000
...
[ 116.606571] Call Trace:
[ 116.609023] <IRQ>
[ 116.611047] complete+0x34/0x50
[ 116.614206] bmp085_eoc_irq+0x9/0x10 [bmp280]
because DEBUG_SHIRQ mechanism fires an IRQ before registration and drivers
ought to be able to handle an interrupt happening before request_irq() returns.
Fixes: aae9539496 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f27237c174 ]
The AMD X370 and other AM4 chipsets (A/B/X 3/4/5 parts) and Threadripper
equivalents have a secondary SMBus controller at I/O port address
0x0B20. This bus is used by several manufacturers to control
motherboard RGB lighting via embedded controllers. I have been using
this bus in my OpenRGB project to control the Aura RGB on many
motherboards and ASRock also uses this bus for their Polychrome RGB
controller.
I am not aware of any CZ-compatible platforms which do not have the
second SMBus channel. All of AMD's AM4- and Threadripper- series
chipsets that OpenRGB users have tested appear to have this secondary
bus. I also noticed this secondary bus is present on older AMD
platforms including my FM1 home server.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202587
Signed-off-by: Adam Honse <calcprogrammer1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ef9d5073b ]
The microphone-jack state needs to be masked in a case of a 4-pin jack
when microphone and ground pins are shorted. Presence of nvidia,headset
tells that WM8903 CODEC driver should mask microphone's status if short
circuit is detected, i.e headphones are inserted.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200330204011.18465-3-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee25d9742d ]
round_down() can only round to powers of 2. If round_down() is asked
to round to something that is not a power of 2, incorrect results are
produced. The incorrect results can be both too large and too small.
Instead, use rounddown() which can round to any number.
Fixes: 6a721db180 ("clk: sunxi: Add A31 clocks support")
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c3d579c8 ]
regmap is a library function that gets selected by drivers that need
it. No driver modules should depend on it. Depending on REGMAP_I2C makes
this driver only build if another driver already selected REGMAP_I2C,
as the symbol can't be selected through the menu kernel configuration.
Fixes: 2219a93596 ("power_supply: Add TI BQ24257 charger driver")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ae5d0d7d8 upstream.
Since commit 03db8b583d ("perf tools: Fix
maps__find_symbol_by_name()") introduced map address range check in
maps__find_symbol_by_name(), we can not get "_etext" from kernel map
because _etext is placed on the edge of the kernel .text section (=
kernel map in perf.)
To fix this issue, this checks the address correctness by map address
range information (map->start and map->end) instead of using _etext
address.
This can cause an error if the target inlined function is embedded in
both __init function and normal function.
For exaample, request_resource() is a normal function but also embedded
in __init reserve_setup(). In this case, the probe point in
reserve_setup() must be skipped.
However, without this fix, it failes to setup all probe points:
# ./perf probe -v request_resource
probe-definition(0): request_resource
symbol:request_resource file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /usr/lib/debug/lib/modules/5.5.17-200.fc31.x86_64/vmlinux for symbols
Open Debuginfo file: /usr/lib/debug/lib/modules/5.5.17-200.fc31.x86_64/vmlinux
Try to find probe point from debuginfo.
Matched function: request_resource [15e29ad]
found inline addr: 0xffffffff82fbf892
Probe point found: reserve_setup+204
found inline addr: 0xffffffff810e9790
Probe point found: request_resource+0
Found 2 probe_trace_events.
Opening /sys/kernel/debug/tracing//kprobe_events write=1
Opening /sys/kernel/debug/tracing//README write=0
Writing event: p:probe/request_resource _text+33290386
Failed to write event: Invalid argument
Error: Failed to add events. Reason: Invalid argument (Code: -22)
#
With this fix,
# ./perf probe request_resource
reserve_setup is out of .text, skip it.
Added new events:
(null):(null) (on request_resource)
probe:request_resource (on request_resource)
You can now use it in all perf tools, such as:
perf record -e probe:request_resource -aR sleep 1
#
Fixes: 03db8b583d ("perf tools: Fix maps__find_symbol_by_name()")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158763967332.30755.4922496724365529088.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80526491c2 upstream.
Fix to check kprobe blacklist address correctly with relocated address
by adjusting debuginfo address.
Since the address in the debuginfo is same as objdump, it is different
from relocated kernel address with KASLR. Thus, 'perf probe' always
misses to catch the blacklisted addresses.
Without this patch, 'perf probe' can not detect the blacklist addresses
on a KASLR enabled kernel.
# perf probe kprobe_dispatcher
Failed to write event: Invalid argument
Error: Failed to add events.
#
With this patch, it correctly shows the error message.
# perf probe kprobe_dispatcher
kprobe_dispatcher is blacklisted function, skip it.
Probe point 'kprobe_dispatcher' not found.
Error: Failed to add events.
#
Fixes: 9aaf5a5f47 ("perf probe: Check kprobes blacklist when adding new events")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158763966411.30755.5882376357738273695.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f41ebe9def upstream.
When a probe point is expanded to several places (like inlined) and if
some of them are skipped because of blacklisted or __init function,
those trace_events has no event name. It must be skipped while showing
results.
Without this fix, you can see "(null):(null)" on the list,
# ./perf probe request_resource
reserve_setup is out of .text, skip it.
Added new events:
(null):(null) (on request_resource)
probe:request_resource (on request_resource)
You can now use it in all perf tools, such as:
perf record -e probe:request_resource -aR sleep 1
#
With this fix, it is ignored:
# ./perf probe request_resource
reserve_setup is out of .text, skip it.
Added new events:
probe:request_resource (on request_resource)
You can now use it in all perf tools, such as:
perf record -e probe:request_resource -aR sleep 1
#
Fixes: 5a51fcd1f3 ("perf probe: Skip kernel symbols which is out of .text")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/158763968263.30755.12800484151476026340.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f51466901c upstream.
nand_cleanup() is supposed to be called on error after a successful
call to nand_scan() to free all NAND resources.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible, hence pointing it as the commit to
fix for backporting purposes, even if this commit is not introducing
any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-41-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24c5efe41c upstream.
gss_mech_register() calls svcauth_gss_register_pseudoflavor() for each
flavour, but gss_mech_unregister() does not call auth_domain_put().
This is unbalanced and makes it impossible to reload the module.
Change svcauth_gss_register_pseudoflavor() to return the registered
auth_domain, and save it for later release.
Cc: stable@vger.kernel.org (v2.6.12+)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d47a5dc288 upstream.
There is no valid case for supporting duplicate pseudoflavor
registrations.
Currently the silent acceptance of such registrations is hiding a bug.
The rpcsec_gss_krb5 module registers 2 flavours but does not unregister
them, so if you load, unload, reload the module, it will happily
continue to use the old registration which now has pointers to the
memory were the module was originally loaded. This could lead to
unexpected results.
So disallow duplicate registrations.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206651
Cc: stable@vger.kernel.org (v2.6.12+)
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 912c0a7f2b upstream.
At boot the FSCR is initialised via one of two paths. On most systems
it's set to a hard coded value in __init_FSCR().
On newer skiboot systems we use the device tree CPU features binding,
where firmware can tell Linux what bits to set in FSCR (and HFSCR).
In both cases the value that's configured at boot is not propagated
into the init_task.thread.fscr value prior to the initial fork of init
(pid 1), which means the value is not used by any processes other than
swapper (the idle task).
For the __init_FSCR() case this is OK, because the value in
init_task.thread.fscr is initialised to something sensible. However it
does mean that the value set in __init_FSCR() is not used other than
for swapper, which is odd and confusing.
The bigger problem is for the device tree CPU features case it
prevents firmware from setting (or clearing) FSCR bits for use by user
space. This means all existing kernels can not have features
enabled/disabled by firmware if those features require
setting/clearing FSCR bits.
We can handle both cases by saving the FSCR value into
init_task.thread.fscr after we have initialised it at boot. This fixes
the bug for device tree CPU features, and will allow us to simplify
the initialisation for the __init_FSCR() case in a future patch.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-3-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 993e3d96fd upstream.
The device tree CPU features binding includes FSCR bit numbers which
Linux is instructed to set by firmware.
Whether that's a good idea or not, in the case of the DSCR the Linux
implementation has a hard requirement that the FSCR_DSCR bit not be
set by default. We use it to track when a process reads/writes to
DSCR, so it must be clear to begin with.
So if firmware tells us to set FSCR_DSCR we must ignore it.
Currently this does not cause a bug in our DSCR handling because the
value of FSCR that the device tree CPU features code establishes is
only used by swapper. All other tasks use the value hard coded in
init_task.thread.fscr.
However we'd like to fix that in a future commit, at which point this
will become necessary.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200527145843.2761782-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 869d42e6eb upstream.
SDHCI1 is connected to a BCM4329 WiFi/BT chip which requires
power to be kept over suspend. As the surrounding hardware supports
this, mark it as such. This fixes WiFi after a suspend/resume cycle.
Fixes: 170642468a ("ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8807d356bf upstream.
GPIO lines for the CM36651 sensor I2C bus use the normal not the inverted
polarity. This bug has been there since adding the CM36651 sensor by
commit 85cb4e0bd2 ("ARM: dts: add cm36651 light/proximity sensor node
for exynos4412-trats2"), but went unnoticed because the "i2c-gpio"
driver ignored the GPIO polarity specified in the device-tree.
The recent conversion of "i2c-gpio" driver to the new, descriptor based
GPIO API, automatically made it the DT-specified polarity aware, what
broke the CM36651 sensor operation.
Fixes: 85cb4e0bd2 ("ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35509737c8 upstream.
The PL310 Auxiliary Control Register shouldn't have the "Full line of
zero" optimization bit being set before L2 cache is enabled. The L2X0
driver takes care of enabling the optimization by itself.
This patch fixes a noisy error message on Tegra20 and Tegra30 telling
that cache optimization is erroneously enabled without enabling it for
the CPU:
L2C-310: enabling full line of zeros but not enabled in Cortex-A9
Cc: <stable@vger.kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54505a1e20 upstream.
The commits cd0e00c106 and 92d7223a74 broke boot on the Alpha Avanti
platform. The patches move memory barriers after a write before the write.
The result is that if there's iowrite followed by ioread, there is no
barrier between them.
The Alpha architecture allows reordering of the accesses to the I/O space,
and the missing barrier between write and read causes hang with serial
port and real time clock.
This patch makes barriers confiorm to the specification.
1. We add mb() before readX_relaxed and writeX_relaxed -
memory-barriers.txt claims that these functions must be ordered w.r.t.
each other. Alpha doesn't order them, so we need an explicit barrier.
2. We add mb() before reads from the I/O space - so that if there's a
write followed by a read, there should be a barrier between them.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: cd0e00c106 ("alpha: io: reorder barriers to guarantee writeX() and iowriteX() ordering")
Fixes: 92d7223a74 ("alpha: io: reorder barriers to guarantee writeX() and iowriteX() ordering #2")
Cc: stable@vger.kernel.org # v4.17+
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64611a15ca upstream.
queue_limits::logical_block_size got changed from unsigned short to
unsigned int, but it was forgotten to update crypt_io_hints() to use the
new type. Fix it.
Fixes: ad6bf88a6c ("block: fix an integer overflow in logical block size")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 142cd25293 upstream.
We do need access_process_vm() to access the target's reg_window.
However, access to caller's memory (storing the result in
genregs32_get(), fetching the new values in case of genregs32_set())
should be done by normal uaccess primitives.
Fixes: ad4f957640 ([SPARC64]: Fix user accesses in regset code.)
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
