[ Upstream commit df4393424a ]
There is an issue with threaded interrupts which are marked ONESHOT
and using the fasteoi handler:
if (IS_ONESHOT())
mask_irq();
....
cond_unmask_eoi_irq()
chip->irq_eoi();
if (setaffinity_pending) {
mask_ioapic();
...
move_affinity();
unmask_ioapic();
}
So if setaffinity is pending the interrupt will be moved and then
unconditionally unmasked at the ioapic level, which is wrong in two
aspects:
1) It should be kept masked up to the point where the threaded handler
finished.
2) The physical chip state and the software masked state are inconsistent
Guard both the mask and the unmask with a check for the software masked
state. If the line is marked masked then the ioapic line is also masked, so
both mask_ioapic() and unmask_ioapic() can be skipped safely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Fixes: 3aa551c9b4 ("genirq: add threaded interrupt handler support")
Link: https://lkml.kernel.org/r/20191017101938.321393687@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eeb91ade9 ]
The RTL8723BU has problems connecting to AP after each warm reboot.
Sometimes it returns no scan result, and in most cases, it fails
the authentication for unknown reason. However, it works totally
fine after cold reboot.
Compare the value of register SYS_CR and SYS_CLK_MAC_CLK_ENABLE
for cold reboot and warm reboot, the registers imply that the MAC
is already powered and thus some procedures are skipped during
driver initialization. Double checked the vendor driver, it reads
the SYS_CR and SYS_CLK_MAC_CLK_ENABLE also but doesn't skip any
during initialization based on them. This commit only tells the
RTL8723BU to do full initialization without checking MAC status.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c3bafaa1f ]
On modern CPUs it is quite normal that the temperature limits are
reached and the CPU is throttled. In fact, often the thermal design is
not sufficient to cool the CPU at full load and limits can quickly be
reached when a burst in load happens. This will even happen with
technologies like RAPL limitting the long term power consumption of
the package.
Also, these limits are "softer", as Srinivas explains:
"CPU temperature doesn't have to hit max(TjMax) to get these warnings.
OEMs ha[ve] an ability to program a threshold where a thermal interrupt
can be generated. In some systems the offset is 20C+ (Read only value).
In recent systems, there is another offset on top of it which can be
programmed by OS, once some agent can adjust power limits dynamically.
By default this is set to low by the firmware, which I guess the
prime motivation of Benjamin to submit the patch."
So these messages do not usually indicate a hardware issue (e.g.
insufficient cooling). Log them as warnings to avoid confusion about
their severity.
[ bp: Massage commit mesage. ]
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Christian Kellner <ckellner@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191009155424.249277-1-bberg@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8c101e28 ]
During the setup() stage, HCI device drivers expect the chip to
acknowledge its setup() completion via vendor specific frames.
If userspace opens() such HCI device in HCI_USER_CHANNEL [1] mode,
the vendor specific frames are never tranmitted to the driver, as
they are filtered in hci_rx_work().
Allow HCI devices which operate in HCI_USER_CHANNEL mode to receive
frames if the HCI device is is HCI_INIT state.
[1] https://www.spinics.net/lists/linux-bluetooth/msg37345.html
Fixes: 23500189d7 ("Bluetooth: Introduce new HCI socket channel for user operation")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db033831b4 ]
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abb0b3d96a ]
commit 1455cf8dbf ("driver core: emit uevents when device is bound
to a driver") added bind and unbind uevents when a driver is bound or
unbound to a physical device.
For USB devices which are handled via the generic usbfs layer (via
libusb for example), this is problematic:
Each time a user space program calls
ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr);
and then later
ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr);
The kernel will now produce a bind or unbind event, which does not
really contain any useful information.
This allows a user space program to run a DoS attack against programs
which listen to uevents (in particular systemd/eudev/upowerd):
A malicious user space program just has to call in a tight loop
ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr);
ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr);
With this loop the malicious user space program floods the kernel and
all programs listening to uevents with tons of bind and unbind
events.
This patch suppresses uevents for ioctls USBDEVFS_CLAIMINTERFACE and
USBDEVFS_RELEASEINTERFACE.
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20191011115518.2801-1-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6942635032 ]
On some devices (e.g. Samsung Galaxy A5 (2015)), the bootloader
seems to keep interrupts enabled for SM5502 when booting Linux.
Changing the cable state (i.e. plugging in a cable) - until the driver
is loaded - will therefore produce an interrupt that is never read.
In this situation, the cable state will be stuck forever on the
initial state because SM5502 stops sending interrupts.
This can be avoided by clearing those pending interrupts after
the driver has been loaded.
One way to do this is to reset all registers to default state
by writing to SM5502_REG_RESET. This ensures that we start from
a clean state, with all interrupts disabled.
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e20b248051 ]
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2444846c0d ]
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06bec72b25 ]
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10dcb615c ]
In mwifiex_pcie_init_evt_ring, a new skb is allocated which should be
released if mwifiex_map_pci_memory() fails. The release for skb and
card->evtbd_ring_vbase is added.
Fixes: 0732484b47 ("mwifiex: separate ring initialization and ring creation routines")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cad8f9115 ]
Currently, proc_cmd is used to dispatch command to 'pg_ctrl', 'pg_thread',
'pg_set'. proc_cmd is designed to check command result with grep the
"Result:", but this might fail since this string is only shown in
'pg_thread' and 'pg_set'.
This commit fixes this logic by grep-ing the "Result:" string only when
the command is not for 'pg_ctrl'.
For clarity of an execution flow, 'errexit' flag has been set.
To cleanup pktgen on exit, trap has been added for EXIT signal.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b211f9c5a ]
The CEC_MSG_GIVE_DECK_STATUS and CEC_MSG_GIVE_TUNER_DEVICE_STATUS commands
both have a status_req argument: ON, OFF, ONCE. If ON or ONCE, then the
follower will reply with a STATUS message. Either once or whenever the
status changes (status_req == ON).
If status_req == OFF, then it will stop sending continuous status updates,
but the follower will *not* send a STATUS message in that case.
This means that if status_req == OFF, then msg->reply should be 0 as well
since no reply is expected in that case.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 649cd16c43 ]
If usb_set_interface() failed, iface->cur_altsetting will
not be assigned and it will be used in flexcop_usb_transfer_init()
It may lead a NULL pointer dereference.
Check usb_set_interface() return value in flexcop_usb_init()
and return failed to avoid using this NULL pointer.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaecce12f5 ]
When unloading omap3-rom-rng, we'll get the following:
WARNING: CPU: 0 PID: 100 at drivers/clk/clk.c:948 clk_core_disable
This is because the clock may be already disabled by omap3_rom_rng_idle().
Let's fix the issue by checking for rng_idle on exit.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 1c6b7c2108 ("hwrng: OMAP3 ROM Random Number Generator support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39abcc8484 ]
When R-Car Gen3 USB 2.0 is in Gadget mode, if host is detached an interrupt
will be generated and Suspended state bit is set in interrupt status
register. Interrupt handler will call driver->suspend(composite_suspend)
if suspended state bit is set. composite_suspend will call
ffs_func_suspend which will post FUNCTIONFS_SUSPEND and will be consumed
by user space application via /dev/ep0.
To be able to detect host detach, extend the DVSQ_MASK to cover the
Suspended bit of the DVSQ[2:0] bitfield from the Interrupt Status
Register 0 (INTSTS0) register and perform appropriate action in the
DVST interrupt handler (usbhsg_irq_dev_state).
Without this commit, disconnection of the phone from R-Car-H3 ES2.0
Salvator-X CN9 port is not recognized and reverse role switch does
not happen. If phone is connected again it does not enumerate.
With this commit, disconnection will be recognized and reverse role
switch will happen by a user space application. If phone is connected
again it will enumerate properly and will become visible in the output
of 'lsusb'.
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1568207756-22325-3-git-send-email-external.veeraiyan.c@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e5705c635 ]
When building cpupower with clang, the following warning appears:
utils/idle_monitor/hsw_ext_idle.c:42:16: warning: initializer overrides
prior initialization of this subobject [-Winitializer-overrides]
.desc = N_("Processor Package C2"),
^~~~~~~~~~~~~~~~~~~~~~
./utils/helpers/helpers.h:25:33: note: expanded from macro 'N_'
#define N_(String) gettext_noop(String)
^~~~~~
./utils/helpers/helpers.h:23:30: note: expanded from macro
'gettext_noop'
#define gettext_noop(String) String
^~~~~~
utils/idle_monitor/hsw_ext_idle.c:41:16: note: previous initialization
is here
.desc = N_("Processor Package C9"),
^~~~~~~~~~~~~~~~~~~~~~
./utils/helpers/helpers.h:25:33: note: expanded from macro 'N_'
#define N_(String) gettext_noop(String)
^~~~~~
./utils/helpers/helpers.h:23:30: note: expanded from macro
'gettext_noop'
#define gettext_noop(String) String
^~~~~~
1 warning generated.
This appears to be a copy and paste or merge mistake because the name
and id fields both have PC9 in them, not PC2. Remove the second
assignment to fix the warning.
Fixes: 7ee767b69b ("cpupower: Add Haswell family 0x45 specific idle monitor to show PC8,9,10 states")
Link: https://github.com/ClangBuiltLinux/linux/issues/718
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3143b459de ]
The driver stores frame format settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, those settings are updated before they are actually applied
on hardware. If an error occurs on device update, the stored settings
my not reflect hardware state anymore and consecutive calls to
.get_fmt() may return incorrect information. That in turn may affect
ability of a bridge device to use correct DMA transfer settings if such
incorrect informmation on active frame format returned by .get_fmt() is
used.
Assuming a failed device update means its state hasn't changed, update
frame format related settings stored in the device private structure
only after they are successfully applied so the stored values always
reflect hardware state as closely as possible.
Fixes: 2f6e240479 ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d669fbfca ]
The initial registers sequence is only loaded at probe
time. Afterward only the resolution and format specific
register are modified. Care must be taken to make sure
registers modified by one resolution setting are reverted
back when another resolution is programmed.
This was not done properly for the 720p case.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7718cf03c3 ]
In case we don't set the sg_prot_tablesize, the scsi layer assign the
default size (65535 entries). We should limit this size since we should
take into consideration the underlaying device capability. This cap is
considered when calculating the sg_tablesize. Otherwise, for example,
we can get that /sys/block/sdb/queue/max_segments is 128 and
/sys/block/sdb/queue/max_integrity_segments is 65535.
Link: https://lore.kernel.org/r/1569359027-10987-1-git-send-email-maxg@mellanox.com
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7da413a185 ]
alloc_workqueue is not checked for errors and as a result,
a potential NULL dereference could occur.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f93616951 ]
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 228241944a ]
Inside a nested 'else' block at the beginning of this function is a
call that assigns 'psta' to the return value of 'rtw_get_stainfo()'.
If 'rtw_get_stainfo()' returns NULL and the flow of control reaches
the 'else if' where 'psta' is dereferenced, then we will dereference
a NULL pointer.
Fix this by checking if 'psta' is not NULL before reading its
'psta->qos_option' data member.
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20190926150317.5894-1-connor.kuehl@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f918a728c ]
This change is necessary for spidev devices (e.g. /dev/spidev3.0) working
in the slave mode (like NXP's dspi driver for Vybrid SoC).
When SPI HW works in this mode - the master is responsible for providing
CS and CLK signals. However, when some fault happens - like for example
distortion on SPI lines - the SPI Linux driver needs a chance to recover
from this abnormal situation and prepare itself for next (correct)
transmission.
This change doesn't pose any threat on drivers working in master mode as
spi_slave_abort() function checks if SPI slave mode is supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20190924110547.14770-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190925091143.15468-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f552fde983 ]
Separate the declaration of struct bh1750_chip_info from definition
of bh1750_chip_info_tbl[] in a single statement as it makes the code
hard to read, and with the extra newline it makes it look as if the
bh1750_chip_info_tbl[] had no explicit type.
This change also resolves the following compiler warning about the
unusual position of the static keyword that can be seen when building
with warnings enabled (W=1):
drivers/iio/light/bh1750.c:64:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Related to commit 3a11fbb037 ("iio: light: add support for ROHM
BH1710/BH1715/BH1721/BH1750/BH1751 ambient light sensors").
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit add9d56d7b upstream.
The current PCM code doesn't initialize explicitly the buffers
allocated for PCM streams, hence it might leak some uninitialized
kernel data or previous stream contents by mmapping or reading the
buffer before actually starting the stream.
Since this is a common problem, this patch simply adds the clearance
of the buffer data at hw_params callback. Although this does only
zero-clear no matter which format is used, which doesn't mean the
silence for some formats, but it should be OK because the intention is
just to clear the previous data on the buffer.
Reported-by: Lionel Koenig <lionel.koenig@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191211155742.3213-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 714cd3e8cb upstream.
If we get an -ENOENT back from btrfs_uuid_iter_rem when iterating the
uuid tree we'll just continue and do btrfs_next_item(). However we've
done a btrfs_release_path() at this point and no longer have a valid
path. So increment the key and go back and do a normal search.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1aa2818a upstream.
If we fail to read the fs root corresponding with a reloc root we'll
just break out and free the reloc roots. But we remove our current
reloc_root from this list higher up, which means we'll leak this
reloc_root. Fix this by adding ourselves back to the reloc_roots list
so we are properly cleaned up.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bc574de59 upstream.
My fsstress modifications coupled with generic/475 uncovered a failure
to mount and replay the log if we hit a orphaned root. We do not want
to replay the log for an orphan root, but it's completely legitimate to
have an orphaned root with a log attached. Fix this by simply skipping
replaying the log. We still need to pin it's root node so that we do
not overwrite it while replaying other logs, as we re-read the log root
at every stage of the replay.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 583e636141 upstream.
We always program the maximum DMA buffer size into the receive descriptor,
although the allocated size may be less. E.g. with the default MTU size
we allocate only 1536 bytes. If somebody sends us a bigger frame, then
memory may get corrupted.
Fix by using exact buffer sizes.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[acj: backport to v4.9 -stable :
- adjust context
- skipped the section modifying non-existent functions in dwxgmac2_descs.c and
hwif.h ]
Signed-off-by: Aviraj CJ <acj@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 057d476fff upstream.
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5480e299b5 upstream.
Some time ago the block layer was modified such that timeout handlers are
called from thread context instead of interrupt context. Make it safe to
run the iSCSI timeout handler in thread context. This patch fixes the
following lockdep complaint:
================================
WARNING: inconsistent lock state
5.5.1-dbg+ #11 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/7:1H/206 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff88802d9827e8 (&(&session->frwd_lock)->rlock){+.?.}, at: iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_check_transport_timeouts+0x3e/0x210 [libiscsi]
call_timer_fn+0x132/0x470
__run_timers.part.0+0x39f/0x5b0
run_timer_softirq+0x63/0xc0
__do_softirq+0x12d/0x5fd
irq_exit+0xb3/0x110
smp_apic_timer_interrupt+0x131/0x3d0
apic_timer_interrupt+0xf/0x20
default_idle+0x31/0x230
arch_cpu_idle+0x13/0x20
default_idle_call+0x53/0x60
do_idle+0x38a/0x3f0
cpu_startup_entry+0x24/0x30
start_secondary+0x222/0x290
secondary_startup_64+0xa4/0xb0
irq event stamp: 1383705
hardirqs last enabled at (1383705): [<ffffffff81aace5c>] _raw_spin_unlock_irq+0x2c/0x50
hardirqs last disabled at (1383704): [<ffffffff81aacb98>] _raw_spin_lock_irq+0x18/0x50
softirqs last enabled at (1383690): [<ffffffffa0e2efea>] iscsi_queuecommand+0x76a/0xa20 [libiscsi]
softirqs last disabled at (1383682): [<ffffffffa0e2e998>] iscsi_queuecommand+0x118/0xa20 [libiscsi]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&session->frwd_lock)->rlock);
<Interrupt>
lock(&(&session->frwd_lock)->rlock);
*** DEADLOCK ***
2 locks held by kworker/7:1H/206:
#0: ffff8880d57bf928 ((wq_completion)kblockd){+.+.}, at: process_one_work+0x472/0xab0
#1: ffff88802b9c7de8 ((work_completion)(&q->timeout_work)){+.+.}, at: process_one_work+0x476/0xab0
stack backtrace:
CPU: 7 PID: 206 Comm: kworker/7:1H Not tainted 5.5.1-dbg+ #11
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0xa5/0xe6
print_usage_bug.cold+0x232/0x23b
mark_lock+0x8dc/0xa70
__lock_acquire+0xcea/0x2af0
lock_acquire+0x106/0x240
_raw_spin_lock+0x38/0x50
iscsi_eh_cmd_timed_out+0xa6/0x6d0 [libiscsi]
scsi_times_out+0xf4/0x440 [scsi_mod]
scsi_timeout+0x1d/0x20 [scsi_mod]
blk_mq_check_expired+0x365/0x3a0
bt_iter+0xd6/0xf0
blk_mq_queue_tag_busy_iter+0x3de/0x650
blk_mq_timeout_work+0x1af/0x380
process_one_work+0x56d/0xab0
worker_thread+0x7a/0x5d0
kthread+0x1bc/0x210
ret_from_fork+0x24/0x30
Fixes: 287922eb0b ("block: defer timeouts to a workqueue")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191209173457.187370-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 474e559567 upstream.
We got the following warnings from thin_check during thin-pool setup:
$ thin_check /dev/vdb
examining superblock
examining devices tree
missing devices: [1, 84]
too few entries in btree_node: 41, expected at least 42 (block 138, max_entries = 126)
examining mapping tree
The phenomenon is the number of entries in one node of details_info tree is
less than (max_entries / 3). And it can be easily reproduced by the following
procedures:
$ new a thin pool
$ presume the max entries of details_info tree is 126
$ new 127 thin devices (e.g. 1~127) to make the root node being full
and then split
$ remove the first 43 (e.g. 1~43) thin devices to make the children
reblance repeatedly
$ stop the thin pool
$ thin_check
The root cause is that the B-tree removal procedure in __rebalance2()
doesn't guarantee the invariance: the minimal number of entries in
non-root node should be >= (max_entries / 3).
Simply fix the problem by increasing the rebalance threshold to
make sure the number of entries in each child will be greater
than or equal to (max_entries / 3 + 1), so no matter which
child is used for removal, the number will still be valid.
Cc: stable@vger.kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d567fb8819 upstream.
Since irq_bypass_register_producer() is called after request_irq(), we
should do tear-down in reverse order: irq_bypass_unregister_producer()
then free_irq().
Specifically free_irq() may release resources required by the
irqbypass del_producer() callback. Notably an example provided by
Marc Zyngier on arm64 with GICv4 that he indicates has the potential
to wedge the hardware:
free_irq(irq)
__free_irq(irq)
irq_domain_deactivate_irq(irq)
its_irq_domain_deactivate()
[unmap the VLPI from the ITS]
kvm_arch_irq_bypass_del_producer(cons, prod)
kvm_vgic_v4_unset_forwarding(kvm, irq, ...)
its_unmap_vlpi(irq)
[Unmap the VLPI from the ITS (again), remap the original LPI]
Signed-off-by: Jiang Yi <giangyi@amazon.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 6d7425f109 ("vfio: Register/unregister irq_bypass_producer")
Link: https://lore.kernel.org/kvm/20191127164910.15888-1-giangyi@amazon.com
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
[aw: commit log]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
