commit 62bba54d99 upstream.
Explicitly set the switch cpu (upstream) port phy-mode and managed
properties. This fixes the Marvell 88E6141 switch serdes configuration
with the recently enabled phylink layer.
Fixes: a612083327 ("arm64: dts: add support for SolidRun Clearfog GT 8K")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01053dadb7 upstream.
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
commit 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes") effectively
reverted this commit 8010f13a40 ("ARM: dts: am43xx: add support for
clkout1 clock") which is needed for the ov2659 camera sensor clock
definition hence it is being re-applied here.
Note that because of the current dts node name dependency for mapping to
clock domain, we must still use "clkout1-*ck" naming instead of generic
"clock@" naming for the node. And because of this, it's probably best to
apply the dts node addition together along with the other clock changes.
Fixes: 664ae1ab25 ("ARM: dts: am43xx: add clkctrl nodes")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d39d86cd4 upstream.
Pull-ups for SAM9 UART/USART TX lines were disabled in a previous
commit. However, several chips in the SAM9 family require pull-ups to
prevent the TX lines from falling (and causing an endless break
condition) when the transceiver is disabled.
From the SAM9G20 datasheet, 32.5.1: "To prevent the TXD line from
falling when the USART is disabled, the use of an internal pull up
is mandatory.". This commit reenables the pull-ups for all chips having
that sentence in their datasheets.
Fixes: 5e04822f7d ("ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20191203142147.875227-1-inguin@gmx.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1eebac0240 upstream.
The uDPU uses both ethernet controllers, which ties up COMPHY 0 for
eth1 and COMPHY 1 for eth0, with no USB3 comphy. The addition of
COMPHY support made the kernel override the setup by the boot loader
breaking this platform by assuming that COMPHY 0 was always used for
USB3. Delete the USB3 COMPHY definition at platform level, and add
phy specifications for the ethernet channels.
Fixes: bd3d25b073 ("arm64: dts: marvell: armada-37xx: link USB hosts with their PHYs")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e0c94d3ae upstream.
The driver gets driver_data from memory that is marked as const (which
is probably put to read-only memory) and it then modifies it. This
likely causes some sort of fault to happen.
Fix this by taking a copy of the structure.
Fixes: c94a8ff14d ("platform/x86: intel_mid_powerbtn: make mid_pb_ddata const")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6da197a2e upstream.
As reported by Guilherme G. Piccoli:
---8<---8<---8<---
The rtc-cmos interrupt setting was changed in the commit 079062b28f
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28f ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1 ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs")
Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b73ea3796 ]
Break an infinite loop when early parsing of the SRAT table is caused
by a subtable with zero length. Known to affect the ASUS WS X299 SAGE
motherboard with firmware version 1201 which has a large block of
zeros in its SRAT table. The kernel could boot successfully on this
board/firmware prior to the introduction of early parsing this table or
after a BIOS update.
[ bp: Fixup whitespace damage and commit message. Make it return 0 to
denote that there are no immovable regions because who knows what
else is broken in this BIOS. ]
Fixes: 02a3e3cdb7 ("x86/boot: Parse SRAT table and count immovable memory regions")
Signed-off-by: Steven Clarkson <sc@lambdal.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-acpi@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206343
Link: https://lkml.kernel.org/r/CAHKq8taGzj0u1E_i=poHUam60Bko5BpiJ9jn0fAupFUYexvdUQ@mail.gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7dc2993a9e upstream.
Currently, each time nfs4_do_fsinfo() is called it will do an implicit
NFS4 lease renewal, which is not compliant with the NFS4 specification.
This can result in a lease being expired by an NFS server.
Commit 83ca7f5ab3 ("NFS: Avoid PUTROOTFH when managing leases")
introduced implicit client lease renewal in nfs4_do_fsinfo(),
which can result in the NFSv4.0 lease to expire on a server side,
and servers returning NFS4ERR_EXPIRED or NFS4ERR_STALE_CLIENTID.
This can easily be reproduced by frequently unmounting a sub-mount,
then stat'ing it to get it mounted again, which will delay or even
completely prevent client from sending RENEW operations if no other
NFS operations are issued. Eventually nfs server will expire client's
lease and return an error on file access or next RENEW.
This can also happen when a sub-mount is automatically unmounted
due to inactivity (after nfs_mountpoint_expiry_timeout), then it is
mounted again via stat(). This can result in a short window during
which client's lease will expire on a server but not on a client.
This specific case was observed on production systems.
This patch removes the implicit lease renewal from nfs4_do_fsinfo().
Fixes: 83ca7f5ab3 ("NFS: Avoid PUTROOTFH when managing leases")
Signed-off-by: Robert Milkowski <rmilkowski@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 924491f2e4 upstream.
Currently, if an nfs server returns NFS4ERR_EXPIRED to open(),
we return EIO to applications without even trying to recover.
Fixes: 272289a3df ("NFSv4: nfs4_do_handle_exception() handle revoke/expiry of a single stateid")
Signed-off-by: Robert Milkowski <rmilkowski@gmail.com>
Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3871224787 upstream.
When comparing two 'struct cred' for equality w.r.t. behaviour under
filesystem access, we need to use cred_fscmp().
Fixes: a52458b48a ("NFS/NFSD/SUNRPC: replace generic creds with 'struct cred'.")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 221203ce64 upstream.
Instead of making assumptions about the commit verifier contents, change
the commit code to ensure we always check that the verifier was set
by the XDR code.
Fixes: f54bcf2ece ("pnfs: Prepare for flexfiles by pulling out common code")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0df68ced55 upstream.
If we suffer a fatal error upon writing a file, which causes us to
need to revalidate the entire mapping, then we should also revalidate
the file size.
Fixes: d2ceb7e570 ("NFS: Don't use page_file_mapping after removing the page")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 474c4f306e upstream.
If CONFIG_SWAP=n, it does not make much sense to offer the user the
option to enable support for swapping over NFS, as that will still fail
at run time:
# swapon /swap
swapon: /swap: swapon failed: Function not implemented
Fix this by adding a dependency on CONFIG_SWAP.
Fixes: a564b8f039 ("nfs: enable swap on NFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b8ac01a4 upstream.
It's currently possible to insert sockets in unexpected states into
a sockmap, due to a TOCTTOU when updating the map from a syscall.
sock_map_update_elem checks that sk->sk_state == TCP_ESTABLISHED,
locks the socket and then calls sock_map_update_common. At this
point, the socket may have transitioned into another state, and
the earlier assumptions don't hold anymore. Crucially, it's
conceivable (though very unlikely) that a socket has become unhashed.
This breaks the sockmap's assumption that it will get a callback
via sk->sk_prot->unhash.
Fix this by checking the (fixed) sk_type and sk_protocol without the
lock, followed by a locked check of sk_state.
Unfortunately it's not possible to push the check down into
sock_(map|hash)_update_common, since BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB
run before the socket has transitioned from TCP_SYN_RECV into
TCP_ESTABLISHED.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200207103713.28175-1-lmb@cloudflare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88d6f130e5 upstream.
It was reported that the max_t, ilog2, and roundup_pow_of_two macros have
exponential effects on the number of states in the sparse checker.
This patch breaks them up by calculating the "nbuckets" first so that the
"bucket_log" only needs to take ilog2().
In addition, Linus mentioned:
Patch looks good, but I'd like to point out that it's not just sparse.
You can see it with a simple
make net/core/bpf_sk_storage.i
grep 'smap->bucket_log = ' net/core/bpf_sk_storage.i | wc
and see the end result:
1 365071 2686974
That's one line (the assignment line) that is 2,686,974 characters in
length.
Now, sparse does happen to react particularly badly to that (I didn't
look to why, but I suspect it's just that evaluating all the types
that don't actually ever end up getting used ends up being much more
expensive than it should be), but I bet it's not good for gcc either.
Fixes: 6ac99e8f23 ("bpf: Introduce bpf sk local storage")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Link: https://lore.kernel.org/bpf/20200207081810.3918919-1-kafai@fb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d3919a953 upstream.
Commit 7e81a35302 ("bpf: Sockmap, ensure sock lock held during tear
down") introduced sleeping issues inside RCU critical sections and while
holding a spinlock on sockmap/sockhash tear-down. There has to be at least
one socket in the map for the problem to surface.
This adds a test that triggers the warnings for broken locking rules. Not a
fix per se, but rather tooling to verify the accompanying fixes. Run on a
VM with 1 vCPU to reproduce the warnings.
Fixes: 7e81a35302 ("bpf: Sockmap, ensure sock lock held during tear down")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200206111652.694507-4-jakub@cloudflare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b2dc83906 upstream.
We need to have a synchronize_rcu before free'ing the sockhash because any
outstanding psock references will have a pointer to the map and when they
use it, this could trigger a use after free.
This is a sister fix for sockhash, following commit 2bb90e5cc9 ("bpf:
sockmap, synchronize_rcu before free'ing map") which addressed sockmap,
which comes from a manual audit.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200206111652.694507-3-jakub@cloudflare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d95f1e8b46 upstream.
Turns out the xlated program instructions can also be missing if
kptr_restrict sysctl is set. This means that the previous fix to check the
jited_prog_insns pointer was insufficient; add another check of the
xlated_prog_insns pointer as well.
Fixes: 5b79bcdf03 ("bpftool: Don't crash on missing jited insns or ksyms")
Fixes: cae73f2339 ("bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump()")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200206102906.112551-1-toke@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc4255eff5 upstream.
When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: fc36ffda32 ("iwlwifi: mvm: support FTM initiator")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d95f20c4f0 upstream.
Previously we did not call INIT_KFIFO() for aer_fifo. This leads to
kfifo_put() sometimes returning 0 (queue full) when in fact it is not.
It is easy to reproduce the problem by using aer-inject:
$ aer-inject -s :82:00.0 multiple-corr-nonfatal
The content of the multiple-corr-nonfatal file is as below:
AER
COR RCVR
HL 0 1 2 3
AER
UNCOR POISON_TLP
HL 4 5 6 7
Fixes: 27c1ce8bbe ("PCI/AER: Use kfifo for tracking events instead of reimplementing it")
Link: https://lore.kernel.org/r/1579767991-103898-1-git-send-email-liudongdong3@huawei.com
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9db8dc6d07 upstream.
Some PCI bridges implement BARs in addition to bridge windows. For
example, here's a PLX switch:
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI
Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30, NUMA node 0
Memory at 90a00000 (32-bit, non-prefetchable) [size=256K]
Bus: primary=04, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: 90000000-909fffff
Prefetchable memory behind bridge: 0000380000800000-0000380000bfffff
Previously, when the kernel assigned resource addresses (with the
pci=realloc command line parameter, for example) it could clear the struct
resource corresponding to the BAR. When this happened, lspci would report
this BAR as "ignored":
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [size=256K]
This is because the kernel reports a zero start address and zero flags
in the corresponding sysfs resource file and in /proc/bus/pci/devices.
Investigation with 'lspci -x', however, shows the BIOS-assigned address
will still be programmed in the device's BAR registers.
It's clearly a bug that the kernel lost track of the BAR value, but in most
cases, this still won't result in a visible issue because nothing uses the
memory, so nothing is affected. However, when an IOMMU is in use, it will
not reserve this space in the IOVA because the kernel no longer thinks the
range is valid. (See dmar_init_reserved_ranges() for the Intel
implementation of this.)
Without the proper reserved range, a DMA mapping may allocate an IOVA that
matches a bridge BAR, which results in DMA accesses going to the BAR
instead of the intended RAM.
The problem was in pci_assign_unassigned_root_bus_resources(). When any
resource from a bridge device fails to get assigned, the code set the
resource's flags to zero. This makes sense for bridge windows, as they
will be re-enabled later, but for regular BARs, it makes the kernel
permanently lose track of the fact that they decode address space.
Change pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() so they only clear "res->flags"
for bridge *windows*, not bridge BARs.
Fixes: da7822e5ad ("PCI: update bridge resources to get more big ranges when allocating space (again)")
Link: https://lore.kernel.org/r/20200108213208.4612-1-logang@deltatee.com
[bhelgaas: commit log, check for pci_is_bridge()]
Reported-by: Kit Chow <kchow@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21a92676e1 upstream.
Fix AFI_PEX2_CTRL reg offset for Tegra30 by moving it from the Tegra20
SoC struct where it erroneously got added. This fixes the AFI_PEX2_CTRL
reg offset being uninitialised subsequently failing to bring up the
third PCIe port.
Fixes: adb2653b3d ("PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct")
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d239380196 upstream.
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4fb4cc5ba upstream.
Below commit missed the AF_IB and loopback code flow in
rdma_resolve_addr(). This leads to an unbalanced cm_id refcount in
cma_work_handler() which puts the refcount which was not incremented prior
to queuing the work.
A call trace is observed with such code flow:
BUG: unable to handle kernel NULL pointer dereference at (null)
[<ffffffff96b67e16>] __mutex_lock_slowpath+0x166/0x1d0
[<ffffffff96b6715f>] mutex_lock+0x1f/0x2f
[<ffffffffc0beabb5>] cma_work_handler+0x25/0xa0
[<ffffffff964b9ebf>] process_one_work+0x17f/0x440
[<ffffffff964baf56>] worker_thread+0x126/0x3c0
Hence, hold the cm_id reference when scheduling the resolve work item.
Fixes: 722c7b2bfe ("RDMA/{cma, core}: Avoid callback on rdma_addr_cancel()")
Link: https://lore.kernel.org/r/20200126142652.104803-2-leon@kernel.org
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a242c36951 upstream.
In rdma_nl_rcv_skb(), the local variable err is assigned the return value
of the supplied callback function, which could be one of
ib_nl_handle_resolve_resp(), ib_nl_handle_set_timeout(), or
ib_nl_handle_ip_res_resp(). These three functions all return skb->len on
success.
rdma_nl_rcv_skb() is merely a copy of netlink_rcv_skb(). The callback
functions used by the latter have the convention: "Returns 0 on success or
a negative error code".
In particular, the statement (equal for both functions):
if (nlh->nlmsg_flags & NLM_F_ACK || err)
implies that rdma_nl_rcv_skb() always will ack a message, independent of
the NLM_F_ACK being set in nlmsg_flags or not.
The fix could be to change the above statement, but it is better to keep
the two *_rcv_skb() functions equal in this respect and instead change the
three callback functions in the rdma subsystem to the correct convention.
Fixes: 2ca546b92a ("IB/sa: Route SA pathrecord query through netlink")
Fixes: ae43f82867 ("IB/core: Add IP to GID netlink offload")
Link: https://lore.kernel.org/r/20191216120436.3204814-1-haakon.bugge@oracle.com
Suggested-by: Mark Haywood <mark.haywood@oracle.com>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Tested-by: Mark Haywood <mark.haywood@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea660ad7c1 upstream.
Using CX-3 virtual functions, either from a bare-metal machine or
pass-through from a VM, MAD packets are proxied through the PF driver.
Since the VF drivers have separate name spaces for MAD Transaction Ids
(TIDs), the PF driver has to re-map the TIDs and keep the book keeping in
a cache.
Following the RDMA Connection Manager (CM) protocol, it is clear when an
entry has to evicted from the cache. When a DREP is sent from
mlx4_ib_multiplex_cm_handler(), id_map_find_del() is called. Similar when
a REJ is received by the mlx4_ib_demux_cm_handler(), id_map_find_del() is
called.
This function wipes out the TID in use from the IDR or XArray and removes
the id_map_entry from the table.
In short, it does everything except the topping of the cake, which is to
remove the entry from the list and free it. In other words, for the REJ
case enumerated above, one id_map_entry will be leaked.
For the other case above, a DREQ has been received first. The reception of
the DREQ will trigger queuing of a delayed work to delete the
id_map_entry, for the case where the VM doesn't send back a DREP.
In the normal case, the VM _will_ send back a DREP, and id_map_find_del()
will be called.
But this scenario introduces a secondary leak. First, when the DREQ is
received, a delayed work is queued. The VM will then return a DREP, which
will call id_map_find_del(). As stated above, this will free the TID used
from the XArray or IDR. Now, there is window where that particular TID can
be re-allocated, lets say by an outgoing REQ. This TID will later be wiped
out by the delayed work, when the function id_map_ent_timeout() is
called. But the id_map_entry allocated by the outgoing REQ will not be
de-allocated, and we have a leak.
Both leaks are fixed by removing the id_map_find_del() function and only
using schedule_delayed(). Of course, a check in schedule_delayed() to see
if the work already has been queued, has been added.
Another benefit of always using the delayed version for deleting entries,
is that we do get a TimeWait effect; a TID no longer in use, will occupy
the XArray or IDR for CM_CLEANUP_CACHE_TIMEOUT time, without any ability
of being re-used for that time period.
Fixes: 3cf69cc8db ("IB/mlx4: Add CM paravirtualization")
Link: https://lore.kernel.org/r/20200123155521.1212288-1-haakon.bugge@oracle.com
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Reviewed-by: Rama Nichanamatlu <rama.nichanamatlu@oracle.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fbb37dd82 upstream.
Some SRP targets that do not support specification SRP-2, put the garbage
to the reserved bits of the SRP login response. The problem was not
detected for a long time because the SRP initiator ignored those bits. But
now one of them is used as SRP_LOGIN_RSP_IMMED_SUPP. And it causes a
critical error on the target when the initiator sends immediate data.
The ib_srp module has a use_imm_date parameter to enable or disable
immediate data manually. But it does not help in the above case, because
use_imm_date is ignored at handling the SRP login response. The problem is
definitely caused by a bug on the target side, but the initiator's
behavior also does not look correct. The initiator should not use
immediate data if use_imm_date is disabled by a user.
This commit adds an additional checking of use_imm_date at the handling of
SRP login response to avoid unexpected use of immediate data.
Fixes: 882981f4a4 ("RDMA/srp: Add support for immediate data")
Link: https://lore.kernel.org/r/20200115133055.30232-1-sergeygo@mellanox.com
Signed-off-by: Sergey Gorenko <sergeygo@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaad647e5c upstream.
In procedure mlx4_ib_add_gid(), if the driver is unable to update the FW
gid table, there is a memory leak in the driver's copy of the gid table:
the gid entry's context buffer is not freed.
If such an error occurs, free the entry's context buffer, and mark the
entry as available (by setting its context pointer to NULL).
Fixes: e26be1bfef ("IB/mlx4: Implement ib_device callbacks")
Link: https://lore.kernel.org/r/20200115085050.73746-1-leon@kernel.org
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c742c59e1f ]
Currently, hv_sock restricts the port the guest socket can accept
connections on. hv_sock divides the socket port namespace into two parts
for server side (listening socket), 0-0x7FFFFFFF & 0x80000000-0xFFFFFFFF
(there are no restrictions on client port namespace). The first part
(0-0x7FFFFFFF) is reserved for sockets where connections can be accepted.
The second part (0x80000000-0xFFFFFFFF) is reserved for allocating ports
for the peer (host) socket, once a connection is accepted.
This reservation of the port namespace is specific to hv_sock and not
known by the generic vsock library (ex: af_vsock). This is problematic
because auto-binds/ephemeral ports are handled by the generic vsock
library and it has no knowledge of this port reservation and could
allocate a port that is not compatible with hv_sock (and legitimately so).
The issue hasn't surfaced so far because the auto-bind code of vsock
(__vsock_bind_stream) prior to the change 'VSOCK: bind to random port for
VMADDR_PORT_ANY' would start walking up from LAST_RESERVED_PORT (1023) and
start assigning ports. That will take a large number of iterations to hit
0x7FFFFFFF. But, after the above change to randomize port selection, the
issue has started coming up more frequently.
There has really been no good reason to have this port reservation logic
in hv_sock from the get go. Reserving a local port for peer ports is not
how things are handled generally. Peer ports should reflect the peer port.
This fixes the issue by lifting the port reservation, and also returns the
right peer port. Since the code converts the GUID to the peer port (by
using the first 4 bytes), there is a possibility of conflicts, but that
seems like a reasonable risk to take, given this is limited to vsock and
that only applies to all local sockets.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acbf27746e ]
Currently, the trigger orders SND_SOC_DPCM_TRIGGER_PRE/POST
determine the order in which FE DAI and BE DAI are triggered.
In the case of SND_SOC_DPCM_TRIGGER_PRE, the FE DAI is
triggered before the BE DAI and in the case of
SND_SOC_DPCM_TRIGGER_POST, the BE DAI is triggered before
the FE DAI. And this order remains the same irrespective of the
trigger command.
In the case of the SOF driver, during playback, the FW
expects the BE DAI to be triggered before the FE DAI during
the START trigger. The BE DAI trigger handles the starting of
Link DMA and so it must be started before the FE DAI is started
to prevent xruns during pause/release. This can be addressed
by setting the trigger order for the FE dai link to
SND_SOC_DPCM_TRIGGER_POST. But during the STOP trigger,
the FW expects the FE DAI to be triggered before the BE DAI.
Retaining the same order during the START and STOP commands,
results in FW error as the DAI component in the FW is still
active.
The issue can be fixed by mirroring the trigger order of
FE and BE DAI's during the START and STOP trigger. So, with the
trigger order set to SND_SOC_DPCM_TRIGGER_PRE, the FE DAI will be
trigger first during SNDRV_PCM_TRIGGER_START/STOP/RESUME
and the BE DAI will be triggered first during the
STOP/SUSPEND/PAUSE commands. Conversely, with the trigger order
set to SND_SOC_DPCM_TRIGGER_POST, the BE DAI will be triggered
first during the SNDRV_PCM_TRIGGER_START/STOP/RESUME commands
and the FE DAI will be triggered first during the
SNDRV_PCM_TRIGGER_STOP/SUSPEND/PAUSE commands.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191104224812.3393-2-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b39a934ec7 ]
The recent patch that substituted a flag on an rxrpc_call for the
connection pointer being NULL as an indication that a call was disconnected
puts the set_bit in the wrong place for service calls. This is only a
problem if a call is implicitly terminated by a new call coming in on the
same connection channel instead of a terminating ACK packet.
In such a case, rxrpc_input_implicit_end_call() calls
__rxrpc_disconnect_call(), which is now (incorrectly) setting the
disconnection bit, meaning that when rxrpc_release_call() is later called,
it doesn't call rxrpc_disconnect_call() and so the call isn't removed from
the peer's error distribution list and the list gets corrupted.
KASAN finds the issue as an access after release on a call, but the
position at which it occurs is confusing as it appears to be related to a
different call (the call site is where the latter call is being removed
from the error distribution list and either the next or pprev pointer
points to a previously released call).
Fix this by moving the setting of the flag from __rxrpc_disconnect_call()
to rxrpc_disconnect_call() in the same place that the connection pointer
was being cleared.
Fixes: 5273a191dc ("rxrpc: Fix NULL pointer deref due to call->conn being cleared on disconnect")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
