[ Upstream commit e3faa49bce ]
Since the original TFO server code was implemented in commit
168a8f5805 ("tcp: TCP Fast Open Server -
main code path") the TFO server code has supported the sysctl bit flag
TFO_SERVER_COOKIE_NOT_REQD. Currently, when the TFO_SERVER_ENABLE and
TFO_SERVER_COOKIE_NOT_REQD sysctl bit flags are set, a server connection
will accept a SYN with N bytes of data (N > 0) that has no TFO cookie,
create a new fast open connection, process the incoming data in the SYN,
and make the connection ready for accepting. After accepting, the
connection is ready for read()/recvmsg() to read the N bytes of data in
the SYN, ready for write()/sendmsg() calls and data transmissions to
transmit data.
This commit changes an edge case in this feature by changing this
behavior to apply to (N >= 0) bytes of data in the SYN rather than only
(N > 0) bytes of data in the SYN. Now, a server will accept a data-less
SYN without a TFO cookie if TFO_SERVER_COOKIE_NOT_REQD is set.
Caveat! While this enables a new kind of TFO (data-less empty-cookie
SYN), some firewall rules setup may not work if they assume such packets
are not legit TFOs and will filter them.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210816205105.2533289-1-luke.w.hsiao@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b8061bad ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cafae4cd62 ]
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a211260c34 ]
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba316be1b6 ]
struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.
This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.
This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
CPU0
----
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
<Interrupt>
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.
As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.
Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.
Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e [1]
Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4367355dd9 ]
When compiling with clang in certain configurations, an objtool warning
appears:
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()
This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.
Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4108b3e6db ]
These for-loops should test against v4l2_dv_timings_presets[i].bt.width,
not if i < v4l2_dv_timings_presets[i].bt.width. Luckily nothing ever broke,
since the smallest width is still a lot higher than the total number of
presets, but it is wrong.
The last item in the presets array is all 0, so the for-loop must stop
when it reaches that sentinel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f809665ee7 ]
The range for analog gain mentioned in the datasheet is [0, 480].
The real gain formula mentioned in the datasheet is:
Gain = 512 / (512 – X)
Hence, values larger than 511 clearly makes no sense. The gain
register field is also documented to be of 9-bits in the datasheet.
Certainly, it is enough to infer that, the kernel driver currently
advertises an arbitrary analog gain max. Fix it by rectifying the
value as per the data sheet i.e. 480.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f93add36 ]
The frame_length_lines (0x0340) registers are hard-coded as follows:
- 4208x3118
frame_length_lines = 0x0c50
- 2104x1560
frame_length_lines = 0x0638
- 1048x780
frame_length_lines = 0x034c
The driver exposes the V4L2_CID_VBLANK control in read-only mode and
sets its value to vts_def - height, where vts_def is a mode-dependent
value coming from the supported_modes array. It is set using one of
the following macros defined in the driver:
#define IMX258_VTS_30FPS 0x0c98
#define IMX258_VTS_30FPS_2K 0x0638
#define IMX258_VTS_30FPS_VGA 0x034c
There's a clear mismatch in the value for the full resolution mode i.e.
IMX258_VTS_30FPS. Fix it by rectifying the macro with the value set for
the frame_length_lines register as stated above.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 220ade7745 ]
Some time ago, I reported a calltrace issue
"did not find a suitable aggregator", please see[1].
After a period of analysis and reproduction, I find
that this problem is caused by concurrency.
Before the problem occurs, the bond structure is like follows:
bond0 - slaver0(eth0) - agg0.lag_ports -> port0 - port1
\
port0
\
slaver1(eth1) - agg1.lag_ports -> NULL
\
port1
If we run 'ifenslave bond0 -d eth1', the process is like below:
excuting __bond_release_one()
|
bond_upper_dev_unlink()[step1]
| | |
| | bond_3ad_lacpdu_recv()
| | ->bond_3ad_rx_indication()
| | spin_lock_bh()
| | ->ad_rx_machine()
| | ->__record_pdu()[step2]
| | spin_unlock_bh()
| | |
| bond_3ad_state_machine_handler()
| spin_lock_bh()
| ->ad_port_selection_logic()
| ->try to find free aggregator[step3]
| ->try to find suitable aggregator[step4]
| ->did not find a suitable aggregator[step5]
| spin_unlock_bh()
| |
| |
bond_3ad_unbind_slave() |
spin_lock_bh()
spin_unlock_bh()
step1: already removed slaver1(eth1) from list, but port1 remains
step2: receive a lacpdu and update port0
step3: port0 will be removed from agg0.lag_ports. The struct is
"agg0.lag_ports -> port1" now, and agg0 is not free. At the
same time, slaver1/agg1 has been removed from the list by step1.
So we can't find a free aggregator now.
step4: can't find suitable aggregator because of step2
step5: cause a calltrace since port->aggregator is NULL
To solve this concurrency problem, put bond_upper_dev_unlink()
after bond_3ad_unbind_slave(). In this way, we can invalid the port
first and skip this port in bond_3ad_state_machine_handler(). This
eliminates the situation that the slaver has been removed from the
list but the port is still valid.
[1]https://lore.kernel.org/netdev/10374.1611947473@famine/
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d07006f05 ]
The current behavior of 'tracex7' doesn't consist with other bpf samples
tracex{1..6}. Other samples do not require any argument to run with, but
tracex7 should be run with btrfs device argument. (it should be executed
with test_override_return.sh)
Currently, tracex7 doesn't have any description about how to run this
program and raises an unexpected error. And this result might be
confusing since users might not have a hunch about how to run this
program.
// Current behavior
# ./tracex7
sh: 1: Syntax error: word unexpected (expecting ")")
// Fixed behavior
# ./tracex7
ERROR: Run with the btrfs device argument!
In order to fix this error, this commit adds logic to report a message
and exit when running this program with a missing argument.
Additionally in test_override_return.sh, there is a problem with
multiple directory(tmpmnt) creation. So in this commit adds a line with
removing the directory with every execution.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210727041056.23455-1-claudiajkang@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ccbdcc4d0 ]
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23411c7200 ]
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7aff291d0 ]
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5492886c14 ]
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 323e0cb473 ]
Fix the following out-of-bounds warnings:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
>> net/core/flow_dissector.c:1104:4: warning: 'memcpy' offset [24, 39] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'struct in6_addr' at offset 8 [-Warray-bounds]
1104 | memcpy(&key_addrs->v6addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1105 | sizeof(key_addrs->v6addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ipv6.h:5,
from net/core/flow_dissector.c:6:
include/uapi/linux/ipv6.h:133:18: note: subobject 'saddr' declared here
133 | struct in6_addr saddr;
| ^~~~~
>> net/core/flow_dissector.c:1059:4: warning: 'memcpy' offset [16, 19] from the object at '<unknown>' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 12 [-Warray-bounds]
1059 | memcpy(&key_addrs->v4addrs, &iph->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1060 | sizeof(key_addrs->v4addrs));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from include/linux/ip.h:17,
from net/core/flow_dissector.c:5:
include/uapi/linux/ip.h:103:9: note: subobject 'saddr' declared here
103 | __be32 saddr;
| ^~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). So, the compiler legitimately complains about it. As these
are just a couple of members, fix this by copying each one of them in
separate calls to memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6321c7acb8 ]
Fix the following out-of-bounds warning:
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/d5ae2e65-1f18-2577-246f-bada7eee6ccd@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b7e9f25e5 ]
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210721103822.3755111-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df00609821 ]
On Armadillo-800-EVA with CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/1
lock: lcdc0_device+0x10c/0x308, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 1 Comm: swapper Not tainted 5.11.0-rc5-armadillo-00036-gbbca04be7a80-dirty #287
Hardware name: Generic R8A7740 (Flattened Device Tree)
[<c010c3c8>] (unwind_backtrace) from [<c010a49c>] (show_stack+0x10/0x14)
[<c010a49c>] (show_stack) from [<c0159534>] (do_raw_spin_lock+0x20/0x94)
[<c0159534>] (do_raw_spin_lock) from [<c040858c>] (dev_pm_get_subsys_data+0x8c/0x11c)
[<c040858c>] (dev_pm_get_subsys_data) from [<c05fbcac>] (genpd_add_device+0x78/0x2b8)
[<c05fbcac>] (genpd_add_device) from [<c0412db4>] (of_genpd_add_device+0x34/0x4c)
[<c0412db4>] (of_genpd_add_device) from [<c0a1ea74>] (board_staging_register_device+0x11c/0x148)
[<c0a1ea74>] (board_staging_register_device) from [<c0a1eac4>] (board_staging_register_devices+0x24/0x28)
of_genpd_add_device() is called before platform_device_register(), as it
needs to attach the genpd before the device is probed. But the spinlock
is only initialized when the device is registered.
Fix this by open-coding the spinlock initialization, cfr.
device_pm_init_common() in the internal drivers/base code, and in the
SuperH early platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/57783ece7ddae55f2bda2f59f452180bff744ea0.1626257398.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcacbf06c8 ]
Currently the composite driver encodes the MaxPower field of
the configuration descriptor by reading the c->MaxPower of the
usb_configuration only if it is non-zero, otherwise it falls back
to using the value hard-coded in CONFIG_USB_GADGET_VBUS_DRAW.
However, there are cases when a configuration must explicitly set
bMaxPower to 0, particularly if its bmAttributes also has the
Self-Powered bit set, which is a valid combination.
This is specifically called out in the USB PD specification section
9.1, in which a PDUSB device "shall report zero in the bMaxPower
field after negotiating a mutually agreeable Contract", and also
verified by the USB Type-C Functional Test TD.4.10.2 Sink Power
Precedence Test.
The fix allows the c->MaxPower to be used for encoding the bMaxPower
even if it is 0, if the self-powered bit is also set. An example
usage of this would be for a ConfigFS gadget to be dynamically
updated by userspace when the Type-C connection is determined to be
operating in Power Delivery mode.
Co-developed-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Ronak Vijay Raheja <rraheja@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210720080907.30292-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ae0123960 ]
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: "Bryan O'Donoghue" <bryan.odonoghue@linaro.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20210701114834.884597-6-zenczykowski@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d14f5c702 ]
In the smk_access_entry() function, if no matching rule is found
in the rust_list, a negative error code will be used to perform bit
operations with the MAY_ enumeration value. This is semantically
wrong. This patch fixes this issue.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef773fc81 ]
Yonghong Song report:
The bpf selftest tc_bpf failed with latest bpf-next.
The following is the command to run and the result:
$ ./test_progs -n 132
[ 40.947571] bpf_testmod: loading out-of-tree module taints kernel.
test_tc_bpf:PASS:test_tc_bpf__open_and_load 0 nsec
test_tc_bpf:PASS:bpf_tc_hook_create(BPF_TC_INGRESS) 0 nsec
test_tc_bpf:PASS:bpf_tc_hook_create invalid hook.attach_point 0 nsec
test_tc_bpf_basic:PASS:bpf_obj_get_info_by_fd 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_attach 0 nsec
test_tc_bpf_basic:PASS:handle set 0 nsec
test_tc_bpf_basic:PASS:priority set 0 nsec
test_tc_bpf_basic:PASS:prog_id set 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_attach replace mode 0 nsec
test_tc_bpf_basic:PASS:bpf_tc_query 0 nsec
test_tc_bpf_basic:PASS:handle set 0 nsec
test_tc_bpf_basic:PASS:priority set 0 nsec
test_tc_bpf_basic:PASS:prog_id set 0 nsec
libbpf: Kernel error message: Failed to send filter delete notification
test_tc_bpf_basic:FAIL:bpf_tc_detach unexpected error: -3 (errno 3)
test_tc_bpf:FAIL:test_tc_internal ingress unexpected error: -3 (errno 3)
The failure seems due to the commit
cfdf0d9ae7 ("rtnetlink: use nlmsg_notify() in rtnetlink_send()")
Deal with ESRCH error in nlmsg_notify() even the report variable is zero.
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Link: https://lore.kernel.org/r/20210719051816.11762-1-yajun.deng@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98a6543917 ]
The user can pass in any value to the driver through the 'ioctl'
interface. The driver dost not check, which may cause DoS bugs.
The following log reveals it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:SetOverlayViewPort+0x133/0x5f0 drivers/video/fbdev/kyro/STG4000OverlayDevice.c:476
Call Trace:
kyro_dev_overlay_viewport_set drivers/video/fbdev/kyro/fbdev.c:378 [inline]
kyrofb_ioctl+0x2eb/0x330 drivers/video/fbdev/kyro/fbdev.c:603
do_fb_ioctl+0x1f3/0x700 drivers/video/fbdev/core/fbmem.c:1171
fb_ioctl+0xeb/0x130 drivers/video/fbdev/core/fbmem.c:1185
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x19b/0x220 fs/ioctl.c:739
do_syscall_64+0x32/0x80 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1626235762-2590-1-git-send-email-zheyuma97@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc6c59892 ]
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb119 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97683c851f ]
The naming of the regulator is problematic. VCC is usually a supply
voltage whereas these devices have a separate VREF pin.
Secondly, the regulator core might have provided a stub regulator if
a real regulator wasn't provided. That would in turn have failed to
provide a voltage when queried. So reality was that there was no way
to use the internal reference.
In order to avoid breaking any dts out in the wild, make sure to fallback
to the original vcc naming if vref is not available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210627163244.1090296-9-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4919ff59c ]
Currently, when userspace reads a datagram with a buffer that is
smaller than this datagram, the data will be truncated and only
part of it can be received by users. It doesn't seem right that
users don't know the datagram size and have to use a huge buffer
to read it to avoid the truncation.
This patch to fix it by keeping the skb in rcv queue until the
whole data is read by users. Only the last msg of the datagram
will be marked with MSG_EOR, just as TCP/SCTP does.
Note that this will work as above only when MSG_EOR is set in the
flags parameter of recvmsg(), so that it won't break any old user
applications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14858dcc3b ]
Updating the current_state field of struct pci_dev the way it is done
in pci_enable_device_flags() before calling do_pci_enable_device() may
not work. For example, if the given PCI device depends on an ACPI
power resource whose _STA method initially returns 0 ("off"), but the
config space of the PCI device is accessible and the power state
retrieved from the PCI_PM_CTRL register is D0, the current_state
field in the struct pci_dev representing that device will get out of
sync with the power.state of its ACPI companion object and that will
lead to power management issues going forward.
To avoid such issues, make pci_enable_device_flags() call
pci_update_current_state() which takes ACPI device power management
into account, if present, to retrieve the current power state of the
device.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8db11aebdb ]
The logic at dib8000_get_init_prbs() has a few issues:
1. the tables used there has an extra unused value at the beginning;
2. the dprintk() message doesn't write the right value when
transmission mode is not 8K;
3. the array overflow validation is done by the callers.
Rewrite the code to fix such issues.
This should also shut up those smatch warnings:
drivers/media/dvb-frontends/dib8000.c:2125 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2129 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_2k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2131 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_4k' 14 <= 14
drivers/media/dvb-frontends/dib8000.c:2134 dib8000_get_init_prbs() error: buffer overflow 'lut_prbs_8k' 14 <= 14
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
