[ Upstream commit 608723c41c ]
The kvfree_rcu() and kfree_rcu() APIs are hazardous in that if you forget
the second argument, it works, but might sleep. This sleeping can be a
correctness bug from atomic contexts, and even in non-atomic contexts
it might introduce unacceptable latencies. This commit therefore adds
kvfree_rcu_mightsleep() and kfree_rcu_mightsleep(), which will replace
the single-argument kvfree_rcu() and kfree_rcu(), respectively.
This commit enables a series of commits that switch from single-argument
kvfree_rcu() and kfree_rcu() to their _mightsleep() counterparts. Once
all of these commits land, the single-argument versions will be removed.
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: 511e64e13d8c ("can: gw: fix RCU/BH usage in cgw_create_job()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e1663810e11c64956aa7e280cf74b2f3284d816 ]
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Kelsey Maes <kelsey@vpprocess.com>
Closes: https://lore.kernel.org/all/C2121586-C87F-4B23-A933-845362C29CA1@vpprocess.com
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Kelsey Maes <kelsey@vpprocess.com>
Link: https://patch.msgid.link/20250430161501.79370-1-kelsey@vpprocess.com
[mkl: add comment]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e6a0243ff002ddbd7ee18a8974ae61d2e6ed00d ]
Use addrconf_addr_gen() to generate IPv6 link-local addresses on GRE
devices in most cases and fall back to using add_v4_addrs() only in
case the GRE configuration is incompatible with addrconf_addr_gen().
GRE used to use addrconf_addr_gen() until commit e5dd729460 ("ip/ip6_gre:
use the same logic as SIT interfaces when computing v6LL address")
restricted this use to gretap and ip6gretap devices, and created
add_v4_addrs() (borrowed from SIT) for non-Ethernet GRE ones.
The original problem came when commit 9af28511be ("addrconf: refuse
isatap eui64 for INADDR_ANY") made __ipv6_isatap_ifid() fail when its
addr parameter was 0. The commit says that this would create an invalid
address, however, I couldn't find any RFC saying that the generated
interface identifier would be wrong. Anyway, since gre over IPv4
devices pass their local tunnel address to __ipv6_isatap_ifid(), that
commit broke their IPv6 link-local address generation when the local
address was unspecified.
Then commit e5dd729460 ("ip/ip6_gre: use the same logic as SIT
interfaces when computing v6LL address") tried to fix that case by
defining add_v4_addrs() and calling it to generate the IPv6 link-local
address instead of using addrconf_addr_gen() (apart for gretap and
ip6gretap devices, which would still use the regular
addrconf_addr_gen(), since they have a MAC address).
That broke several use cases because add_v4_addrs() isn't properly
integrated into the rest of IPv6 Neighbor Discovery code. Several of
these shortcomings have been fixed over time, but add_v4_addrs()
remains broken on several aspects. In particular, it doesn't send any
Router Sollicitations, so the SLAAC process doesn't start until the
interface receives a Router Advertisement. Also, add_v4_addrs() mostly
ignores the address generation mode of the interface
(/proc/sys/net/ipv6/conf/*/addr_gen_mode), thus breaking the
IN6_ADDR_GEN_MODE_RANDOM and IN6_ADDR_GEN_MODE_STABLE_PRIVACY cases.
Fix the situation by using add_v4_addrs() only in the specific scenario
where the normal method would fail. That is, for interfaces that have
all of the following characteristics:
* run over IPv4,
* transport IP packets directly, not Ethernet (that is, not gretap
interfaces),
* tunnel endpoint is INADDR_ANY (that is, 0),
* device address generation mode is EUI64.
In all other cases, revert back to the regular addrconf_addr_gen().
Also, remove the special case for ip6gre interfaces in add_v4_addrs(),
since ip6gre devices now always use addrconf_addr_gen() instead.
Note:
This patch was originally applied as commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation."). However, it was then reverted
by commit fc486c2d060f ("Revert "gre: Fix IPv6 link-local address
generation."") because it uncovered another bug that ended up
breaking net/forwarding/ip6gre_custom_multipath_hash.sh. That other
bug has now been fixed by commit 4d0ab3a6885e ("ipv6: Start path
selection from the first nexthop"). Therefore we can now revive this
GRE patch (no changes since original commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation.").
Fixes: e5dd729460 ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/a88cc5c4811af36007645d610c95102dccb360a6.1746225214.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3769478610135e82b262640252d90f6efb05be71 ]
Alan reported a NULL pointer dereference in htb_next_rb_node()
after we made htb_qlen_notify() idempotent.
It turns out in the following case it introduced some regression:
htb_dequeue_tree():
|-> fq_codel_dequeue()
|-> qdisc_tree_reduce_backlog()
|-> htb_qlen_notify()
|-> htb_deactivate()
|-> htb_next_rb_node()
|-> htb_deactivate()
For htb_next_rb_node(), after calling the 1st htb_deactivate(), the
clprio[prio]->ptr could be already set to NULL, which means
htb_next_rb_node() is vulnerable here.
For htb_deactivate(), although we checked qlen before calling it, in
case of qlen==0 after qdisc_tree_reduce_backlog(), we may call it again
which triggers the warning inside.
To fix the issues here, we need to:
1) Make htb_deactivate() idempotent, that is, simply return if we
already call it before.
2) Make htb_next_rb_node() safe against ptr==NULL.
Many thanks to Alan for testing and for the reproducer.
Fixes: 5ba8b837b522 ("sch_htb: make htb_qlen_notify() idempotent")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250428232955.1740419-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb4447bcce915b43b691123118893fca4f372a8f ]
The previous patch that added bounds check for create lease context
introduced a memory leak. When the bounds check fails, the function
returns NULL without freeing the previously allocated lease_ctx_info
structure.
This patch fixes the issue by adding kfree(lreq) before returning NULL
in both boundary check cases.
Fixes: bab703ed8472 ("ksmbd: add bounds check for create lease context")
Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0ca6df4f40cf4c32487944aaf48319cb6c25accc upstream.
ksmbd_vfs_stream_write() did not validate whether the write offset
(*pos) was within the bounds of the existing stream data length (v_len).
If *pos was greater than or equal to v_len, this could lead to an
out-of-bounds memory write.
This patch adds a check to ensure *pos is less than v_len before
proceeding. If the condition fails, -EINVAL is returned.
Cc: stable@vger.kernel.org
Signed-off-by: Norbert Szetei <norbert@doyensec.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84f5eb833f53ae192baed4cfb8d9eaab43481fc9 upstream.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-1-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0713a1b3276b98c7dafbeefef00d7bc3a9119a84 upstream.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5591ce0069ddda97cdbbea596bed53e698f399c2 upstream.
Define vqmmc regulator-gpio for usdhc2 with vin-supply
coming from LDO5.
Without this definition LDO5 will be powered down, disabling
SD card after bootup. This has been introduced in commit
f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5").
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Fixes: f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5")
Tested-by: Manuel Traut <manuel.traut@mt.com>
Reviewed-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@mt.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 650266ac4c7230c89bcd1307acf5c9c92cfa85e2 upstream.
We need to call dm_put_live_table() even if dm_get_live_table() returns
NULL.
Fixes: 9355a9eb21 ("dm: support key eviction from keyslot managers of underlying devices")
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6eab7034579917f207ca6d8e3f4e11e85e0ab7d5 ]
On R-Car:
OF: /sound: Read of boolean property 'simple-audio-card,bitclock-master' with a value.
OF: /sound: Read of boolean property 'simple-audio-card,frame-master' with a value.
or:
OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'bitclock-master' with a value.
OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value.
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Replace testing for presence before calling of_property_read_u32() by
testing for an -EINVAL return value from the latter, to simplify the
code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/db10e96fbda121e7456d70e97a013cbfc9755f4d.1737533954.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69dd15a8ef0ae494179fd15023aa8172188db6b7 ]
Use of_property_read_bool() to read boolean properties rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20240731191312.1710417-20-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 6eab70345799 ("ASoC: soc-core: Stop using of_property_read_bool() for non-boolean properties")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b675ab8efbf2bcee25be29e865455c56e246401 ]
[Why]
Guards automatically release mutex when it goes out of scope making
code easier to follow.
[How]
Replace all use of mutex_lock()/mutex_unlock() with guard(mutex).
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: be593d9d91c5 ("drm/amd/display: Fix slab-use-after-free in hdcp")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 393e834848 ]
Refactor the sequence in hdcp_update_display() to use
mod_hdcp_update_display().
Previous sequence:
- remove()->add()
This Sequence was used to update the display, (mod_hdcp_update_display
didn't exist at the time). This meant for any hdcp updates (type changes,
enable/disable) we would remove, reconstruct, and add. This leads to
unnecessary calls to psp eventually
New Sequence using mod_hdcp_update_display():
- add() once when stream is enabled
- use update() for all updates
The update function checks for prev == new states and will not
unnecessarily end up calling psp via add/remove.
Reviewed-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: be593d9d91c5 ("drm/amd/display: Fix slab-use-after-free in hdcp")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa9fdd5d5a ]
[why]
For MST topology with 1 physical link and multiple connectors (>=2),
e.g. daisy cahined MST + SST, or 1-to-multi MST hub, if userspace
set to enable the HDCP simultaneously on all connected outputs, the
commit tail iteratively call the hdcp_update_display() for each
display (connector). However, the hdcp workqueue data structure for
each link has only one DM connector and encryption status members,
which means the work queue of property_validate/update() would only
be triggered for the last connector within this physical link, and
therefore the HDCP property value of other connectors would stay on
DESIRED instead of switching to ENABLED, which is NOT as expected.
[how]
Use array of AMDGPU_DM_MAX_DISPLAY_INDEX for both aconnector and
encryption status in hdcp workqueue data structure for each physical
link. For property validate/update work queue, we iterates over the
array and do similar operation/check for each connected display.
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: be593d9d91c5 ("drm/amd/display: Fix slab-use-after-free in hdcp")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b00d24997a11c10d3e420614f0873b83ce358a34 ]
ASPEED VGA card has two built-in devices:
0008:06:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 06)
0008:07:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (rev 52)
Its toplogy looks like this:
+-[0008:00]---00.0-[01-09]--+-00.0-[02-09]--+-00.0-[03]----00.0 Sandisk Corp Device 5017
| +-01.0-[04]--
| +-02.0-[05]----00.0 NVIDIA Corporation Device
| +-03.0-[06-07]----00.0-[07]----00.0 ASPEED Technology, Inc. ASPEED Graphics Family
| +-04.0-[08]----00.0 Renesas Technology Corp. uPD720201 USB 3.0 Host Controller
| \-05.0-[09]----00.0 Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
\-00.1 PMC-Sierra Inc. Device 4028
The IORT logic populaties two identical IDs into the fwspec->ids array via
DMA aliasing in iort_pci_iommu_init() called by pci_for_each_dma_alias().
Though the SMMU driver had been able to handle this situation since commit
563b5cbe33 ("iommu/arm-smmu-v3: Cope with duplicated Stream IDs"), that
got broken by the later commit cdf315f907 ("iommu/arm-smmu-v3: Maintain
a SID->device structure"), which ended up with allocating separate streams
with the same stuffing.
On a kernel prior to v6.15-rc1, there has been an overlooked warning:
pci 0008:07:00.0: vgaarb: setting as boot VGA device
pci 0008:07:00.0: vgaarb: bridge control possible
pci 0008:07:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
pcieport 0008:06:00.0: Adding to iommu group 14
ast 0008:07:00.0: stream 67328 already in tree <===== WARNING
ast 0008:07:00.0: enabling device (0002 -> 0003)
ast 0008:07:00.0: Using default configuration
ast 0008:07:00.0: AST 2600 detected
ast 0008:07:00.0: [drm] Using analog VGA
ast 0008:07:00.0: [drm] dram MCLK=396 Mhz type=1 bus_width=16
[drm] Initialized ast 0.1.0 for 0008:07:00.0 on minor 0
ast 0008:07:00.0: [drm] fb0: astdrmfb frame buffer device
With v6.15-rc, since the commit bcb81ac6ae3c ("iommu: Get DT/ACPI parsing
into the proper probe path"), the error returned with the warning is moved
to the SMMU device probe flow:
arm_smmu_probe_device+0x15c/0x4c0
__iommu_probe_device+0x150/0x4f8
probe_iommu_group+0x44/0x80
bus_for_each_dev+0x7c/0x100
bus_iommu_probe+0x48/0x1a8
iommu_device_register+0xb8/0x178
arm_smmu_device_probe+0x1350/0x1db0
which then fails the entire SMMU driver probe:
pci 0008:06:00.0: Adding to iommu group 21
pci 0008:07:00.0: stream 67328 already in tree
arm-smmu-v3 arm-smmu-v3.9.auto: Failed to register iommu
arm-smmu-v3 arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22
Since SMMU driver had been already expecting a potential duplicated Stream
ID in arm_smmu_install_ste_for_dev(), change the arm_smmu_insert_master()
routine to ignore a duplicated ID from the fwspec->sids array as well.
Note: this has been failing the iommu_device_probe() since 2021, although a
recent iommu commit in v6.15-rc1 that moves iommu_device_probe() started to
fail the SMMU driver probe. Since nobody has cared about DMA Alias support,
leave that as it was but fix the fundamental iommu_device_probe() breakage.
Fixes: cdf315f907 ("iommu/arm-smmu-v3: Maintain a SID->device structure")
Cc: stable@vger.kernel.org
Suggested-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Link: https://lore.kernel.org/r/20250415185620.504299-1-nicolinc@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2bb820e862d61f9ca1499e500915f9f505a2655 ]
Since v5.12 the rbtree has gained some simplifying helpers aimed at making
rb tree users write less convoluted boiler plate code. Instead the caller
provides a single comparison function and the helpers generate the prior
open-coded stuff.
Update smmu->streams to use rb_find_add() and rb_find().
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/1-v3-9fef8cdc2ff6+150d1-smmuv3_tidy_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
Stable-dep-of: b00d24997a11 ("iommu/arm-smmu-v3: Fix iommu_device_probe bug due to duplicated stream ids")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3318dc299b072a0511d6dfd8367f3304fb6d9827 ]
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Retain the function for later use.
Fixes: 0644b3daca ("irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1a7bc8382b0d4208258f7d2a4474fae788dd90 ]
Commit c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific
PHY fixup") removed a PHY fixup that setted the clock mode and the LED
mode.
Make the Ethernet interface work again by doing as advised in the
commit's log, set clock mode and the LED mode in the device tree.
Fixes: c7e73b5051 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4567bdaaaaa1744da3d7da07d9aca2f941f5b4e5 ]
Completion of the FFA_PARTITION_INFO_GET ABI transfers the ownership of
the caller’s Rx buffer from the producer(typically partition mnager) to
the consumer(this driver/OS). FFA_RX_RELEASE transfers the ownership
from the consumer back to the producer.
However, when we set the flag to just return the count of partitions
deployed in the system corresponding to the specified UUID while
invoking FFA_PARTITION_INFO_GET, the Rx buffer ownership shouldn't be
transferred to this driver. We must be able to skip transferring back
the ownership to the partition manager when we request just to get the
count of the partitions as the buffers are not acquired in this case.
Firmware may return FFA_RET_DENIED or other error for the ffa_rx_release()
in such cases.
Fixes: bb1be74985 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
Message-Id: <20250321115700.3525197-1-sudeep.holla@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ca67840c0ddf3f39407339624cef824a4f27599 ]
Using device_find_child() to lookup the proper SCMI device to destroy
causes an unbalance in device refcount, since device_find_child() calls an
implicit get_device(): this, in turns, inhibits the call of the provided
release methods upon devices destruction.
As a consequence, one of the structures that is not freed properly upon
destruction is the internal struct device_private dev->p populated by the
drivers subsystem core.
KMemleak detects this situation since loading/unloding some SCMI driver
causes related devices to be created/destroyed without calling any
device_release method.
unreferenced object 0xffff00000f583800 (size 512):
comm "insmod", pid 227, jiffies 4294912190
hex dump (first 32 bytes):
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
ff ff ff ff ff ff ff ff 60 36 1d 8a 00 80 ff ff ........`6......
backtrace (crc 114e2eed):
kmemleak_alloc+0xbc/0xd8
__kmalloc_cache_noprof+0x2dc/0x398
device_add+0x954/0x12d0
device_register+0x28/0x40
__scmi_device_create.part.0+0x1bc/0x380
scmi_device_create+0x2d0/0x390
scmi_create_protocol_devices+0x74/0xf8
scmi_device_request_notifier+0x1f8/0x2a8
notifier_call_chain+0x110/0x3b0
blocking_notifier_call_chain+0x70/0xb0
scmi_driver_register+0x350/0x7f0
0xffff80000a3b3038
do_one_initcall+0x12c/0x730
do_init_module+0x1dc/0x640
load_module+0x4b20/0x5b70
init_module_from_file+0xec/0x158
$ ./scripts/faddr2line ./vmlinux device_add+0x954/0x12d0
device_add+0x954/0x12d0:
kmalloc_noprof at include/linux/slab.h:901
(inlined by) kzalloc_noprof at include/linux/slab.h:1037
(inlined by) device_private_init at drivers/base/core.c:3510
(inlined by) device_add at drivers/base/core.c:3561
Balance device refcount by issuing a put_device() on devices found via
device_find_child().
Reported-by: Alice Ryhl <aliceryhl@google.com>
Closes: https://lore.kernel.org/linux-arm-kernel/Z8nK3uFkspy61yjP@arm.com/T/#mc1f73a0ea5e41014fa145147b7b839fc988ada8f
CC: Sudeep Holla <sudeep.holla@arm.com>
CC: Catalin Marinas <catalin.marinas@arm.com>
Fixes: d4f9dddd21 ("firmware: arm_scmi: Add dynamic scmi devices creation")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Alice Ryhl <aliceryhl@google.com>
Message-Id: <20250306185447.2039336-1-cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a7a15f39c682ac4268624da2abdb9114bdde96d5 upstream.
est_qlen_notify() deletes its class from its active list with
list_del() when qlen is 0, therefore, it is not idempotent and
not friendly to its callers, like fq_codel_dequeue().
Let's make it idempotent to ease qdisc_tree_reduce_backlog() callers'
life. Also change other list_del()'s to list_del_init() just to be
extra safe.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250403211033.166059-6-xiyou.wangcong@gmail.com
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51eb3b65544c9efd6a1026889ee5fb5aa62da3bb upstream.
hfsc_qlen_notify() is not idempotent either and not friendly
to its callers, like fq_codel_dequeue(). Let's make it idempotent
to ease qdisc_tree_reduce_backlog() callers' life:
1. update_vf() decreases cl->cl_nactive, so we can check whether it is
non-zero before calling it.
2. eltree_remove() always removes RB node cl->el_node, but we can use
RB_EMPTY_NODE() + RB_CLEAR_NODE() to make it safe.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250403211033.166059-4-xiyou.wangcong@gmail.com
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c567c86b90 upstream.
'io_acct_set' is only used for raid0 and raid456, prepare to use it for
raid1 and raid10, so that io accounting from different levels can be
consistent.
By the way, follow up patches will also use this io clone mechanism to
make sure 'active_io' represents in flight io, not io that is dispatching,
so that mddev_suspend will wait for io to be done as designed.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230621165110.1498313-2-yukuai1@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee512922ddd7d64afe2b28830a88f19063217649 ]
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4dda902dac194e3231a1ed0f76c6c3b6340ba8a ]
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55f362885951b2d00fd7fbb02ef0227deea572c2 ]
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6b9c6ea5a55045eed6526d8ee49e93192d1a58 ]
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
Fixes: 08a100689d ("net: hns3: re-organize vector handle")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250430093052.2400464-3-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef2383d078edcbe3055032436b16cdf206f26de2 ]
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad4 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a179aad12badc43201cbf45d1e8ed2c1383c76b9 ]
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1fa ("net: fec: add variable reg_desc_active to speed things up")
Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d52e2e38b85c8b7bc00dca55c2499f46f8c8198 ]
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77e40bbce93059658aee02786a32c5c98a240a8a ]
This patch addresses a data corruption issue observed in nvme-tcp during
testing.
In an NVMe native multipath setup, when an I/O timeout occurs, all
inflight I/Os are canceled almost immediately after the kernel socket is
shut down. These canceled I/Os are reported as host path errors,
triggering a failover that succeeds on a different path.
However, at this point, the original I/O may still be outstanding in the
host's network transmission path (e.g., the NIC’s TX queue). From the
user-space app's perspective, the buffer associated with the I/O is
considered completed since they're acked on the different path and may
be reused for new I/O requests.
Because nvme-tcp enables zero-copy by default in the transmission path,
this can lead to corrupted data being sent to the original target,
ultimately causing data corruption.
We can reproduce this data corruption by injecting delay on one path and
triggering i/o timeout.
To prevent this issue, this change ensures that all inflight
transmissions are fully completed from host's perspective before
returning from queue stop. To handle concurrent I/O timeout from multiple
namespaces under the same controller, always wait in queue stop
regardless of queue's state.
This aligns with the behavior of queue stopping in other NVMe fabric
transports.
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Michael Liang <mliang@purestorage.com>
Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Randy Jennings <randyj@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02e8be5a032cae0f4ca33c6053c44d83cf4acc93 ]
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027 ("bnxt_en: Add support for 'ethtool -d'")
Reviewed-by: Shruti Parab <shruti.parab@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b87bd94f34370bbf1dfa59352bed8efab5bf419 ]
When retrieving the FW coredump using ethtool, it can sometimes cause
memory corruption:
BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45):
__bnxt_get_coredump+0x3ef/0x670 [bnxt_en]
ethtool_get_dump_data+0xdc/0x1a0
__dev_ethtool+0xa1e/0x1af0
dev_ethtool+0xa8/0x170
dev_ioctl+0x1b5/0x580
sock_do_ioctl+0xab/0xf0
sock_ioctl+0x1ce/0x2e0
__x64_sys_ioctl+0x87/0xc0
do_syscall_64+0x5c/0xf0
entry_SYSCALL_64_after_hwframe+0x78/0x80
...
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands.
Fixes: c74751f4c3 ("bnxt_en: Return error if FW returns more data than dump length")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Shruti Parab <shruti.parab@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
