[ Upstream commit 4c76114932d1d6fad2e72823e7898a3c960cf2a7 ]
Correct stream detection by initializing the structure
pqi_scsi_dev_raid_map_data to 0s.
When the OS issues SCSI READ commands, the driver erroneously considers
them as SCSI WRITES. If they are identified as sequential IOs, the driver
then submits those requests via the RAID path instead of the AIO path.
The 'is_write' flag might be set for SCSI READ commands also. The driver
may interpret SCSI READ commands as SCSI WRITE commands, resulting in IOs
being submitted through the RAID path.
Note: This does not cause data corruption.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20240827185501.692804-3-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9e9e0852d501f169aa3bb34e4b413d2eb48c37 ]
This commit adds a null check for the 'afb' variable in the
amdgpu_dm_plane_handle_cursor_update function. Previously, 'afb' was
assumed to be null, but was used later in the code without a null check.
This could potentially lead to a null pointer dereference.
Changes since v1:
- Moved the null check for 'afb' to the line where 'afb' is used. (Alex)
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_plane.c:1298 amdgpu_dm_plane_handle_cursor_update() error: we previously assumed 'afb' could be null (see line 1252)
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Co-developed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95d9e0803e51d5a24276b7643b244c7477daf463 ]
[WHY & HOW]
dc->clk_mgr is null checked previously in the same function, indicating
it might be null.
Passing "dc" to "dc->hwss.apply_idle_power_optimizations", which
dereferences null "dc->clk_mgr". (The function pointer resolves to
"dcn35_apply_idle_power_optimizations".)
This fixes 1 FORWARD_NULL issue reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8141f21b941710ecebe49220b69822cab3abd23d ]
This commit adds a null check for 'stream_status' in the function
'planes_changed_for_existing_stream'. Previously, the code assumed
'stream_status' could be null, but did not handle the case where it was
actually null. This could lead to a null pointer dereference.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_resource.c:3784 planes_changed_for_existing_stream() error: we previously assumed 'stream_status' could be null (see line 3774)
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcc31692a1d1e21f0d06c5f727c03ee299d2264e ]
Before this change there were 16 vid:pid based quirks to ignore the battery
reported by Elan I2C-HID touchscreens on various Asus and HP laptops.
And a report has been received that the 04F3:2A00 I2C touchscreen on
the HP ProBook x360 11 G5 EE/86CF also reports a non present battery.
Since I2C-HID devices are always builtin to laptops they are not battery
owered so it should be safe to just ignore the battery on all Elan I2C-HID
devices, rather then adding a 17th quirk for the 04F3:2A00 touchscreen.
As reported in the changelog of commit a3a5a37efba1 ("HID: Ignore battery
for ELAN touchscreens 2F2C and 4116"), which added 2 new Elan touchscreen
quirks about a month ago, the HID reported battery seems to be related
to a stylus being used. But even when a stylus is in use it does not
properly report the charge of the stylus battery, instead the reported
battery charge jumps from 0% to 1%. So it is best to just ignore the
HID battery.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2302776
Cc: Louis Dalibard <ontake@ontake.dev>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93b0f9e11ce511353c65b7f924cf5f95bd9c3aba ]
Rename the array sil_blacklist to sil_quirks as this name is more
neutral and is also consistent with how this driver define quirks with
the SIL_QUIRK_XXX flags.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 858048568c9e3887d8b19e101ee72f129d65cb15 ]
Let's not use the term blacklist in the function
serverworks_osb4_filter() documentation comment and rather simply refer
to what that function looks at: the list of devices with groken UDMA5.
While at it, also constify the values of the csb_bad_ata100 array.
Of note is that all of this should probably be handled using libata
quirk mechanism but it is unclear if these UDMA5 quirks are specific
to this controller only.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66d71a72539e173a9b00ca0b1852cbaa5f5bf1ad ]
This commit addresses a null pointer dereference issue in the
`commit_planes_for_stream` function at line 4140. The issue could occur
when `top_pipe_to_program` is null.
The fix adds a check to ensure `top_pipe_to_program` is not null before
accessing its stream_res. This prevents a null pointer dereference.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:4140 commit_planes_for_stream() error: we previously assumed 'top_pipe_to_program' could be null (see line 3906)
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c86ad39140bbcb9dc75a10046c2221f657e8083b ]
Pass pointer reference to amdgpu_bo_unref to clear the correct pointer,
otherwise amdgpu_bo_unref clear the local variable, the original pointer
not set to NULL, this could cause use-after-free bug.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fec5f8e8c6bcf83ed7a392801d7b44c5ecfc1e82 ]
Before this commit, only submits with both a BO_HANDLES chunk and a
'bo_list_handle' would be rejected (by amdgpu_cs_parser_bos).
But if UMD sent multiple BO_HANDLES, what would happen is:
* only the last one would be really used
* all the others would leak memory as amdgpu_cs_p1_bo_handles would
overwrite the previous p->bo_list value
This commit rejects submissions with multiple BO_HANDLES chunks to
match the implementation of the parser.
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cf74230c139f208b7fb313ae0054386eee31a81 ]
If qi_submit_sync() is invoked with 0 invalidation descriptors (for
instance, for DMA draining purposes), we can run into a bug where a
submitting thread fails to detect the completion of invalidation_wait.
Subsequently, this led to a soft lockup. Currently, there is no impact
by this bug on the existing users because no callers are submitting
invalidations with 0 descriptors. This fix will enable future users
(such as DMA drain) calling qi_submit_sync() with 0 count.
Suppose thread T1 invokes qi_submit_sync() with non-zero descriptors, while
concurrently, thread T2 calls qi_submit_sync() with zero descriptors. Both
threads then enter a while loop, waiting for their respective descriptors
to complete. T1 detects its completion (i.e., T1's invalidation_wait status
changes to QI_DONE by HW) and proceeds to call reclaim_free_desc() to
reclaim all descriptors, potentially including adjacent ones of other
threads that are also marked as QI_DONE.
During this time, while T2 is waiting to acquire the qi->q_lock, the IOMMU
hardware may complete the invalidation for T2, setting its status to
QI_DONE. However, if T1's execution of reclaim_free_desc() frees T2's
invalidation_wait descriptor and changes its status to QI_FREE, T2 will
not observe the QI_DONE status for its invalidation_wait and will
indefinitely remain stuck.
This soft lockup does not occur when only non-zero descriptors are
submitted.In such cases, invalidation descriptors are interspersed among
wait descriptors with the status QI_IN_USE, acting as barriers. These
barriers prevent the reclaim code from mistakenly freeing descriptors
belonging to other submitters.
Considered the following example timeline:
T1 T2
========================================
ID1
WD1
while(WD1!=QI_DONE)
unlock
lock
WD1=QI_DONE* WD2
while(WD2!=QI_DONE)
unlock
lock
WD1==QI_DONE?
ID1=QI_DONE WD2=DONE*
reclaim()
ID1=FREE
WD1=FREE
WD2=FREE
unlock
soft lockup! T2 never sees QI_DONE in WD2
Where:
ID = invalidation descriptor
WD = wait descriptor
* Written by hardware
The root of the problem is that the descriptor status QI_DONE flag is used
for two conflicting purposes:
1. signal a descriptor is ready for reclaim (to be freed)
2. signal by the hardware that a wait descriptor is complete
The solution (in this patch) is state separation by using QI_FREE flag
for #1.
Once a thread's invalidation descriptors are complete, their status would
be set to QI_FREE. The reclaim_free_desc() function would then only
free descriptors marked as QI_FREE instead of those marked as
QI_DONE. This change ensures that T2 (from the previous example) will
correctly observe the completion of its invalidation_wait (marked as
QI_DONE).
Signed-off-by: Sanjay K Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20240728210059.1964602-1-jacob.jun.pan@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11377947b5861fa59bf77c827e1dd7c081842cc9 ]
Currently, if the rcuscale module's async module parameter is specified
for RCU implementations that do not have async primitives such as RCU
Tasks Rude (which now lacks a call_rcu_tasks_rude() function), there
will be a series of splats due to calls to a NULL pointer. This commit
therefore warns of this situation, but switches to non-async testing.
Signed-off-by: "Paul E. McKenney" <paulmck@kernel.org>
Signed-off-by: Neeraj Upadhyay <neeraj.upadhyay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a6921095eb04a900e0000da83d9475eb958e61e ]
In the pxafb_probe function, it calls the pxafb_init_fbinfo function,
after which &fbi->task is associated with pxafb_task. Moreover,
within this pxafb_init_fbinfo function, the pxafb_blank function
within the &pxafb_ops struct is capable of scheduling work.
If we remove the module which will call pxafb_remove to make cleanup,
it will call unregister_framebuffer function which can call
do_unregister_framebuffer to free fbi->fb through
put_fb_info(fb_info), while the work mentioned above will be used.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| pxafb_task
pxafb_remove |
unregister_framebuffer(info) |
do_unregister_framebuffer(fb_info) |
put_fb_info(fb_info) |
// free fbi->fb | set_ctrlr_state(fbi, state)
| __pxafb_lcd_power(fbi, 0)
| fbi->lcd_power(on, &fbi->fb.var)
| //use fbi->fb
Fix it by ensuring that the work is canceled before proceeding
with the cleanup in pxafb_remove.
Note that only root user can remove the driver at runtime.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95cdd538e0e5677efbdf8aade04ec098ab98f457 ]
The driver core can register and cleanup sysfs groups already.
Make use of that functionality to simplify the error handling and
cleanup.
Also avoid a UAF race during unregistering where the sysctl attributes
were usable after the info struct was freed.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d19d638b1e6cf746263ef60b7d0dee0204d8216a ]
Modern (fortified) memcpy() prefers to avoid writing (or reading) beyond
the end of the addressed destination (or source) struct member:
In function ‘fortify_memcpy_chk’,
inlined from ‘syscall_get_arguments’ at ./arch/x86/include/asm/syscall.h:85:2,
inlined from ‘populate_seccomp_data’ at kernel/seccomp.c:258:2,
inlined from ‘__seccomp_filter’ at kernel/seccomp.c:1231:3:
./include/linux/fortify-string.h:580:25: error: call to ‘__read_overflow2_field’ declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
580 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As already done for x86_64 and compat mode, do not use memcpy() to
extract syscall arguments from struct pt_regs but rather just perform
direct assignments. Binary output differences are negligible, and actually
ends up using less stack space:
- sub $0x84,%esp
+ sub $0x6c,%esp
and less text size:
text data bss dec hex filename
10794 252 0 11046 2b26 gcc-32b/kernel/seccomp.o.stock
10714 252 0 10966 2ad6 gcc-32b/kernel/seccomp.o.after
Closes: https://lore.kernel.org/lkml/9b69fb14-df89-4677-9c82-056ea9e706f5@gmail.com/
Reported-by: Mirsad Todorovac <mtodorovac69@gmail.com>
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Mirsad Todorovac <mtodorovac69@gmail.com>
Link: https://lore.kernel.org/all/20240708202202.work.477-kees%40kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1a58f61d88642ae1e6e97e9d72d73bc70a93cb8 ]
Clang on higher optimization levels detects that NULL is passed to
printf("%s") and warns about it.
While printf() from nolibc gracefully handles that NULL,
it is undefined behavior as per POSIX, so the warning is reasonable.
Avoid the warning by transforming NULL into a non-NULL placeholder.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20240807-nolibc-llvm-v2-8-c20f2f5fc7c2@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1daea158d0aae0770371f3079305a29fdb66829e ]
As mentioned in the comment, the workaround for
__attribute__((no_stack_protector)) is only necessary on GCC.
Avoid applying the workaround on clang, as clang does not recognize
__attribute__((__optimize__)) and would fail.
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20240807-nolibc-llvm-v2-3-c20f2f5fc7c2@weissschuh.net
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c01f3815453e2d5f699ccd8c8c1f93a5b8669e59 ]
The current MIDI input flush on HDSP and HDSPM drivers relies on the
hardware reporting the right value. If the hardware doesn't give the
proper value but returns -1, it may be stuck at an infinite loop.
Add a counter and break if the loop is unexpectedly too long.
Link: https://patch.msgid.link/20240808091513.31380-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b986c7430a6bb68d523dac7bfc74cbd5b44ef96 ]
ASIHPI driver stores some values in the static array upon a response
from the driver, and its index depends on the firmware. We shouldn't
trust it blindly.
This patch adds a sanity check of the array index to fit in the array
size.
Link: https://patch.msgid.link/20240808091454.30846-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5760929f6545c651682de3c2c6c6786816b17bb1 ]
A kexec kernel boot failure is sometimes observed on AMD CPUs due to an
unmapped EFI config table array. This can be seen when "nogbpages" is on
the kernel command line, and has been observed as a full BIOS reboot rather
than a successful kexec.
This was also the cause of reported regressions attributed to Commit
7143c5f4cf20 ("x86/mm/ident_map: Use gbpages only where full GB page should
be mapped.") which was subsequently reverted.
To avoid this page fault, explicitly include the EFI config table array in
the kexec identity map.
Further explanation:
The following 2 commits caused the EFI config table array to be
accessed when enabling sev at kernel startup.
commit ec1c66af3a ("x86/compressed/64: Detect/setup SEV/SME features
earlier during boot")
commit c01fce9cef ("x86/compressed: Add SEV-SNP feature
detection/setup")
This is in the code that examines whether SEV should be enabled or not, so
it can even affect systems that are not SEV capable.
This may result in a page fault if the EFI config table array's address is
unmapped. Since the page fault occurs before the new kernel establishes its
own identity map and page fault routines, it is unrecoverable and kexec
fails.
Most often, this problem is not seen because the EFI config table array
gets included in the map by the luck of being placed at a memory address
close enough to other memory areas that *are* included in the map created
by kexec.
Both the "nogbpages" command line option and the "use gpbages only where
full GB page should be mapped" change greatly reduce the chance of being
included in the map by luck, which is why the problem appears.
Signed-off-by: Tao Liu <ltao@redhat.com>
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Pavin Joseph <me@pavinjoseph.com>
Tested-by: Sarah Brofeldt <srhb@dbc.dk>
Tested-by: Eric Hagberg <ehagberg@gmail.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/all/20240717213121.3064030-2-steve.wahl@hpe.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10b554919d4cc8fa8fe2e95b57ad2624728c8e4 ]
A process can disable access to the alternate signal stack by not
enabling the altstack's PKEY in the PKRU register.
Nevertheless, the kernel updates the PKRU temporarily for signal
handling. However, in sigreturn(), restore_sigcontext() will restore the
PKRU to the user-defined PKRU value.
This will cause restore_altstack() to fail with a SIGSEGV as it needs read
access to the altstack which is prohibited by the user-defined PKRU value.
Fix this by restoring altstack before restoring PKRU.
Signed-off-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240802061318.2140081-5-aruna.ramakrishna@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24cf2bc982ffe02aeffb4a3885c71751a2c7023b ]
Assume there's a multithreaded application that runs untrusted user
code. Each thread has its stack/code protected by a non-zero PKEY, and the
PKRU register is set up such that only that particular non-zero PKEY is
enabled. Each thread also sets up an alternate signal stack to handle
signals, which is protected by PKEY zero. The PKEYs man page documents that
the PKRU will be reset to init_pkru when the signal handler is invoked,
which means that PKEY zero access will be enabled. But this reset happens
after the kernel attempts to push fpu state to the alternate stack, which
is not (yet) accessible by the kernel, which leads to a new SIGSEGV being
sent to the application, terminating it.
Enabling both the non-zero PKEY (for the thread) and PKEY zero in
userspace will not work for this use case. It cannot have the alt stack
writeable by all - the rationale here is that the code running in that
thread (using a non-zero PKEY) is untrusted and should not have access
to the alternate signal stack (that uses PKEY zero), to prevent the
return address of a function from being changed. The expectation is that
kernel should be able to set up the alternate signal stack and deliver
the signal to the application even if PKEY zero is explicitly disabled
by the application. The signal handler accessibility should not be
dictated by whatever PKRU value the thread sets up.
The PKRU register is managed by XSAVE, which means the sigframe contents
must match the register contents - which is not the case here. It's
required that the signal frame contains the user-defined PKRU value (so
that it is restored correctly from sigcontext) but the actual register must
be reset to init_pkru so that the alt stack is accessible and the signal
can be delivered to the application. It seems that the proper fix here
would be to remove PKRU from the XSAVE framework and manage it separately,
which is quite complicated. As a workaround, do this:
orig_pkru = rdpkru();
wrpkru(orig_pkru & init_pkru_value);
xsave_to_user_sigframe();
put_user(pkru_sigframe_addr, orig_pkru)
In preparation for writing PKRU to sigframe, pass PKRU as an additional
parameter down the call chain from get_sigframe().
No functional change.
Signed-off-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240802061318.2140081-2-aruna.ramakrishna@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf96ab1a966b87b09fdd9e8cc8357d2d00776a3a ]
Protect against the kcpuid code parsing faulty max subleaf numbers
through a min() expression. Thus, ensuring that max_subleaf will always
be ≤ MAX_SUBLEAF_NUM.
Use "u32" for the subleaf numbers since kcpuid is compiled with -Wextra,
which includes signed/unsigned comparisons warnings.
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240718134755.378115-5-darwi@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fbf16992e5aa14acf0441320033a01a32309ded ]
If reading version and variant from registers fails (which is unlikely
but possible, because it is a read over bus), the driver will proceed
and perform device configuration based on uninitialized stack variables.
Handle it a bit better - bail out without doing any init and failing the
update status Soundwire callback.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240710-asoc-wsa88xx-version-v1-2-f1c54966ccde@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d79e13f8e8abb5cd3a2a0f9fc9bc3fc750c5b06f ]
Apply the newly introduced macros for reduce the complex expressions
and cast in the quirk table definitions. It results in a significant
code reduction, too.
There should be no functional changes.
Link: https://patch.msgid.link/20240814134844.2726-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3ad39b791c2ecf718afcaca30e5ceafa939d5c ]
Many entries in the USB-audio quirk tables have relatively complex
expressions. For improving the readability, introduce a few macros.
Those are applied in the following patch.
Link: https://patch.msgid.link/20240814134844.2726-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 830802a0fea8fb39d3dc9fb7d6b5581e1343eb1f ]
Breno observed panics when using failslab under certain conditions during
runtime:
can not alloc irq_pin_list (-1,0,20)
Kernel panic - not syncing: IO-APIC: failed to add irq-pin. Can not proceed
panic+0x4e9/0x590
mp_irqdomain_alloc+0x9ab/0xa80
irq_domain_alloc_irqs_locked+0x25d/0x8d0
__irq_domain_alloc_irqs+0x80/0x110
mp_map_pin_to_irq+0x645/0x890
acpi_register_gsi_ioapic+0xe6/0x150
hpet_open+0x313/0x480
That's a pointless panic which is a leftover of the historic IO/APIC code
which panic'ed during early boot when the interrupt allocation failed.
The only place which might justify panic is the PIT/HPET timer_check() code
which tries to figure out whether the timer interrupt is delivered through
the IO/APIC. But that code does not require to handle interrupt allocation
failures. If the interrupt cannot be allocated then timer delivery fails
and it either panics due to that or falls back to legacy mode.
Cure this by removing the panic wrapper around __add_pin_to_irq_node() and
making mp_irqdomain_alloc() aware of the failure condition and handle it as
any other failure in this function gracefully.
Reported-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Breno Leitao <leitao@debian.org>
Tested-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/all/ZqfJmUF8sXIyuSHN@gmail.com
Link: https://lore.kernel.org/all/20240802155440.275200843@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 901e85677ec0bb9a69fb9eab1feafe0c4eb7d07e ]
For an invalid input value that is out of the given range, currently
USB-audio driver corrects the value silently and accepts without
errors. This is no wrong behavior, per se, but the recent kselftest
rather wants to have an error in such a case, hence a different
behavior is expected now.
This patch adds a sanity check at each control put for the standard
mixer types and returns an error if an invalid value is given.
Note that this covers only the standard mixer types. The mixer quirks
that have own control callbacks would need different coverage.
Link: https://patch.msgid.link/20240806124651.28203-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 498365e52bebcbc36a93279fe7e9d6aec8479cee ]
Replace one-element array with a flexible-array member in
`struct host_cmd_ds_802_11_scan_ext`.
With this, fix the following warning:
elo 16 17:51:58 surfacebook kernel: ------------[ cut here ]------------
elo 16 17:51:58 surfacebook kernel: memcpy: detected field-spanning write (size 243) of single field "ext_scan->tlv_buffer" at drivers/net/wireless/marvell/mwifiex/scan.c:2239 (size 1)
elo 16 17:51:58 surfacebook kernel: WARNING: CPU: 0 PID: 498 at drivers/net/wireless/marvell/mwifiex/scan.c:2239 mwifiex_cmd_802_11_scan_ext+0x83/0x90 [mwifiex]
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Closes: https://lore.kernel.org/linux-hardening/ZsZNgfnEwOcPdCly@black.fi.intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/ZsZa5xRcsLq9D+RX@elsanto
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2423cc20087ae9a7b7af575aa62304ef67cad7b6 ]
This patch moves the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_changelink in front of the evaluation of data[IFLA_CAN_BITTIMING].
This avoids a call to do_set_data_bittiming providing a stale
can_priv::ctrlmode with a CAN_CTRLMODE_FD flag not matching the
requested state when switching between a CAN Classic and CAN-FD bitrate.
In the same manner the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_validate is also moved in front of the evaluation of
data[IFLA_CAN_BITTIMING].
This is a preparation for patches where the nominal and data bittiming
may have interdependencies on the driver side depending on the
CAN_CTRLMODE_FD flag state.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://patch.msgid.link/20240808164224.213522-1-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e9629d0ae977d6f6916d7e519724804e95f0b07 ]
Use perf_allow_kernel() for 'pa_enable' (physical addresses),
'pct_enable' (physical timestamps) and context IDs. This means that
perf_event_paranoid is now taken into account and LSM hooks can be used,
which is more consistent with other perf_event_open calls. For example
PERF_SAMPLE_PHYS_ADDR uses perf_allow_kernel() rather than just
perfmon_capable().
This also indirectly fixes the following error message which is
misleading because perf_event_paranoid is not taken into account by
perfmon_capable():
$ perf record -e arm_spe/pa_enable/
Error:
Access to performance monitoring and observability operations is
limited. Consider adjusting /proc/sys/kernel/perf_event_paranoid
setting ...
Suggested-by: Al Grant <al.grant@arm.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240827145113.1224604-1-james.clark@linaro.org
Link: https://lore.kernel.org/all/20240807120039.GD37996@noisy.programming.kicks-ass.net/
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9e5df4a257afc3a471a82961ace9a22b88295a ]
We found that one close-wait socket was reset by the other side
due to a new connection reusing the same port which is beyond our
expectation, so we have to investigate the underlying reason.
The following experiment is conducted in the test environment. We
limit the port range from 40000 to 40010 and delay the time to close()
after receiving a fin from the active close side, which can help us
easily reproduce like what happened in production.
Here are three connections captured by tcpdump:
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965525191
127.0.0.1.9999 > 127.0.0.1.40002: Flags [S.], seq 2769915070
127.0.0.1.40002 > 127.0.0.1.9999: Flags [.], ack 1
127.0.0.1.40002 > 127.0.0.1.9999: Flags [F.], seq 1, ack 1
// a few seconds later, within 60 seconds
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965590730
127.0.0.1.9999 > 127.0.0.1.40002: Flags [.], ack 2
127.0.0.1.40002 > 127.0.0.1.9999: Flags [R], seq 2965525193
// later, very quickly
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965590730
127.0.0.1.9999 > 127.0.0.1.40002: Flags [S.], seq 3120990805
127.0.0.1.40002 > 127.0.0.1.9999: Flags [.], ack 1
As we can see, the first flow is reset because:
1) client starts a new connection, I mean, the second one
2) client tries to find a suitable port which is a timewait socket
(its state is timewait, substate is fin_wait2)
3) client occupies that timewait port to send a SYN
4) server finds a corresponding close-wait socket in ehash table,
then replies with a challenge ack
5) client sends an RST to terminate this old close-wait socket.
I don't think the port selection algo can choose a FIN_WAIT2 socket
when we turn on tcp_tw_reuse because on the server side there
remain unread data. In some cases, if one side haven't call close() yet,
we should not consider it as expendable and treat it at will.
Even though, sometimes, the server isn't able to call close() as soon
as possible like what we expect, it can not be terminated easily,
especially due to a second unrelated connection happening.
After this patch, we can see the expected failure if we start a
connection when all the ports are occupied in fin_wait2 state:
"Ncat: Cannot assign requested address."
Reported-by: Jade Dong <jadedong@tencent.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240823001152.31004-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae5a0456e0b4cfd7e61619e55251ffdf1bc7adfb ]
Modify netpoll_setup() and __netpoll_setup() to ensure that the netpoll
structure (np) is left in a clean state if setup fails for any reason.
This prevents carrying over misconfigured fields in case of partial
setup success.
Key changes:
- np->dev is now set only after successful setup, ensuring it's always
NULL if netpoll is not configured or if netpoll_setup() fails.
- np->local_ip is zeroed if netpoll setup doesn't complete successfully.
- Added DEBUG_NET_WARN_ON_ONCE() checks to catch unexpected states.
- Reordered some operations in __netpoll_setup() for better logical flow.
These changes improve the reliability of netpoll configuration, since it
assures that the structure is fully initialized or totally unset.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240822111051.179850-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
