commit 0373ca7483 upstream.
commit a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0adb24e03a upstream.
The change to flush_kernel_vmap_range() wasn't sufficient to avoid the
SMP stalls. The problem is some drivers call these routines with
interrupts disabled. Interrupts need to be enabled for flush_tlb_all()
and flush_cache_all() to work. This version adds checks to ensure
interrupts are not disabled before calling routines that need IPI
interrupts. When interrupts are disabled, we now drop into slower code.
The attached change fixes the ordering of cache and TLB flushes in
several cases. When we flush the cache using the existing PTE/TLB
entries, we need to flush the TLB after doing the cache flush. We don't
need to do this when we flush the entire instruction and data caches as
these flushes don't use the existing TLB entries. The same is true for
tmpalias region flushes.
The flush_kernel_vmap_range() and invalidate_kernel_vmap_range()
routines have been updated.
Secondly, we added a new purge_kernel_dcache_range_asm() routine to
pacache.S and use it in invalidate_kernel_vmap_range(). Nominally,
purges are faster than flushes as the cache lines don't have to be
written back to memory.
Hopefully, this is sufficient to resolve the remaining problems due to
cache speculation. So far, testing indicates that this is the case. I
did work up a patch using tmpalias flushes, but there is a performance
hit because we need the physical address for each page, and we also need
to sequence access to the tmpalias flush code. This increases the
probability of stalls.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c52232a49e upstream.
On CPU hotunplug the enqueued timers of the unplugged CPU are migrated to a
live CPU. This happens from the control thread which initiated the unplug.
If the CPU on which the control thread runs came out from a longer idle
period then the base clock of that CPU might be stale because the control
thread runs prior to any event which forwards the clock.
In such a case the timers from the unplugged CPU are queued on the live CPU
based on the stale clock which can cause large delays due to increased
granularity of the outer timer wheels which are far away from base:;clock.
But there is a worse problem than that. The following sequence of events
illustrates it:
- CPU0 timer1 is queued expires = 59969 and base->clk = 59131.
The timer is queued at wheel level 2, with resulting expiry time = 60032
(due to level granularity).
- CPU1 enters idle @60007, with next timer expiry @60020.
- CPU0 is hotplugged at @60009
- CPU1 exits idle and runs the control thread which migrates the
timers from CPU0
timer1 is now queued in level 0 for immediate handling in the next
softirq because the requested expiry time 59969 is before CPU1 base->clk
60007
- CPU1 runs code which forwards the base clock which succeeds because the
next expiring timer. which was collected at idle entry time is still set
to 60020.
So it forwards beyond 60007 and therefore misses to expire the migrated
timer1. That timer gets expired when the wheel wraps around again, which
takes between 63 and 630ms depending on the HZ setting.
Address both problems by invoking forward_timer_base() for the control CPUs
timer base. All other places, which might run into a similar problem
(mod_timer()/add_timer_on()) already invoke forward_timer_base() to avoid
that.
[ tglx: Massaged comment and changelog ]
Fixes: a683f390b9 ("timers: Forward the wheel clock whenever possible")
Co-developed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Lingutla Chandrasekhar <clingutla@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: linux-arm-msm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180118115022.6368-1-clingutla@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71db96ddfa upstream.
We've added a quirk to enable the recent Lenovo dock support, where it
overwrites the pin configs of NID 0x17 and 19, not only updating the
pin config cache. It works right after the boot, but the problem is
that the pin configs are occasionally cleared when the machine goes to
PM. Meanwhile the quirk writes the pin configs only at the pre-probe,
so this won't be applied any longer.
For addressing that issue, this patch moves the code to overwrite the
pin configs into HDA_FIXUP_ACT_INIT section so that it's always
applied at both probe and resume time.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195161
Fixes: 61fcf8ece9 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ba8f9d308 upstream.
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee70bc1e7b upstream.
tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.
This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b3a13173f upstream.
The buffers used as tx_buf/rx_buf in a SPI transfer need to be DMA-safe.
This cannot be guaranteed for the buffers passed to tpm_tis_spi_read_bytes
and tpm_tis_spi_write_bytes. Therefore, we need to use our own DMA-safe
buffer and copy the data to/from it.
The buffer needs to be allocated separately, to ensure that it is
cacheline-aligned and not shared with other data, so that DMA can work
correctly.
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c37fbc09bd upstream.
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9d4d9b5a5 upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b8cb28d7c upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d24cd186d upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebabcf17bc upstream.
GCC7 is a bit too eager to generate suboptimal __multi3 calls (128bit
multiply with 128bit result) for MIPS64r6 builds, even in code which
doesn't explicitly use 128bit types, such as the following:
unsigned long func(unsigned long a, unsigned long b)
{
return a > (~0UL) / b;
}
Which GCC rearanges to:
return (unsigned __int128)a * (unsigned __int128)b > 0xffffffffffffffff;
Therefore implement __multi3, but only for MIPS64r6 with GCC7 as under
normal circumstances we wouldn't expect any calls to __multi3 to be
generated from kernel code.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@mips.com>
Cc: Matthew Fortune <matthew.fortune@mips.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17890/
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 45ee9d5e97 ("KVM: arm/arm64: Check pagesize when allocating a
hugepage at Stage 2") lost the check for PMD_SIZE during the backport
to 4.9.
Fix this by correcting the condition to detect hugepages during stage
2 allocation.
Fixes: 45ee9d5e97 ("KVM: arm/arm64: Check pagesize when allocating a hugepage at Stage 2")
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11d827a993 ]
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c76f97c99a ]
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf2acf66ad ]
When cleaning up after a partially successful gntdev_mmap(), unmap the
successfully mapped grant pages otherwise Xen will kill the domain if
in debug mode (Attempt to implicitly unmap a granted PTE) or Linux will
kill the process and emit "BUG: Bad page map in process" if Xen is in
release mode.
This is only needed when use_ptemod is true because gntdev_put_map()
will unmap grant pages itself when use_ptemod is false.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 195e2addbc ]
The 'sh_eth' driver's probe() method would fail on the SolutionEngine7710
board and crash on SolutionEngine7712 board as the platform code is
hopelessly behind the driver's platform data -- it passes the PHY address
instead of 'struct sh_eth_plat_data *'; pass the latter to the driver in
order to fix the bug...
Fixes: 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56c0290202 ]
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9f ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b707fda2df ]
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78f3000493 ]
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13454c1455 ]
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 736a80bbfd ]
If there are multiple mesh stations with the same MAC address,
they will both get confused and start throwing warnings.
Obviously in this case nothing can actually work anyway, so just
drop frames that look like they're from ourselves early on.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ea15452ee ]
nl80211_nan_add_func() does not check if the required attribute
NL80211_NAN_FUNC_FOLLOW_UP_DEST is present when processing
NL80211_CMD_ADD_NAN_FUNCTION request. This request can be issued
by users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attribute presence.
Signed-off-by: Hao Chen <flank3rsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 248de22e63 ]
The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.
This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0bace7984 ]
libc-compat.h aims to prevent symbol collisions between uapi and libc
headers for each supported libc. This requires continuous coordination
between them.
The goal of this commit is to improve the situation for libcs (such as
musl) which are not yet supported and/or do not wish to be explicitly
supported, while not affecting supported libcs. More precisely, with
this commit, unsupported libcs can request the suppression of any
specific uapi definition by defining the correspondings _UAPI_DEF_*
macro as 0. This can fix symbol collisions for them, as long as the
libc headers are included before the uapi headers. Inclusion in the
other order is outside the scope of this commit.
All infrastructure in order to enable this fallback for unsupported
libcs is already in place, except that libc-compat.h unconditionally
defines all _UAPI_DEF_* macros to 1 for all unsupported libcs so that
any previous definitions are ignored. In order to fix this, this commit
merely makes these definitions conditional.
This commit together with the musl libc commit
http://git.musl-libc.org/cgit/musl/commit/?id=04983f2272382af92eb8f8838964ff944fbb8258
fixes for example the following compiler errors when <linux/in6.h> is
included after musl's <netinet/in.h>:
./linux/in6.h:32:8: error: redefinition of 'struct in6_addr'
./linux/in6.h:49:8: error: redefinition of 'struct sockaddr_in6'
./linux/in6.h:59:8: error: redefinition of 'struct ipv6_mreq'
The comments referencing glibc are still correct, but this file is not
only used for glibc any more.
Signed-off-by: Felix Janda <felix.janda@posteo.de>
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d02fd6e7d2 ]
Because the macvlan_uninit would free the macvlan port, so there is one
double free case in macvlan_common_newlink. When the macvlan port is just
created, then register_netdevice or netdev_upper_dev_link failed and they
would invoke macvlan_uninit. Then it would reach the macvlan_port_destroy
which triggers the double free.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16ba3defb8 ]
When using enhanced mode for IPoIB, two threads may execute xmit in
parallel to two different TX queues while the target is the same.
In this case, both of them will add the same neighbor to the path's
neigh link list and we might see the following message:
list_add double add: new=ffff88024767a348, prev=ffff88024767a348...
WARNING: lib/list_debug.c:31__list_add_valid+0x4e/0x70
ipoib_start_xmit+0x477/0x680 [ib_ipoib]
dev_hard_start_xmit+0xb9/0x3e0
sch_direct_xmit+0xf9/0x250
__qdisc_run+0x176/0x5d0
__dev_queue_xmit+0x1f5/0xb10
__dev_queue_xmit+0x55/0xb10
Analysis:
Two SKB are scheduled to be transmitted from two cores.
In ipoib_start_xmit, both gets NULL when calling ipoib_neigh_get.
Two calls to neigh_add_path are made. One thread takes the spin-lock
and calls ipoib_neigh_alloc which creates the neigh structure,
then (after the __path_find) the neigh is added to the path's neigh
link list. When the second thread enters the critical section it also
calls ipoib_neigh_alloc but in this case it gets the already allocated
ipoib_neigh structure, which is already linked to the path's neigh
link list and adds it again to the list. Which beside of triggering
the list, it creates a loop in the linked list. This loop leads to
endless loop inside path_rec_completion.
Solution:
Check list_empty(&neigh->list) before adding to the list.
Add a similar fix in "ipoib_multicast.c::ipoib_mcast_send"
Fixes: b63b70d877 ('IPoIB: Use a private hash table for path lookup in xmit path')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a371cf87e ]
ibmr.device is being set only after ib_alloc_mr() is successfully complete.
Therefore, in case imlx4_mr_enable() returns with error, the error flow
unwinder calls to mlx4_free_priv_pages(), which uses ibmr.device.
Such usage causes to NULL dereference oops and to fix it, the IB device
should be set in the mr struct earlier stage (e.g. prior to calling
mlx4_free_priv_pages()).
Fixes: 1b2cd0fc67 ("IB/mlx4: Support the new memory registration API")
Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a9bd4f8eb ]
We store per path and per device configuration data to identify the
path or device correctly. The per path configuration data might get
mixed up if the original request gets into error recovery and is
started with a random path mask.
This would lead to a wrong identification of a path in case of a CUIR
event for example.
Fix by copying the path mask from the original request to the error
recovery request in case it is a path verification request.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11bca0a83f ]
An interrupt storm on a bad interrupt will cause the kernel
log to be clogged.
[ 60.089234] ->handle_irq(): ffffffffbe2f803f,
[ 60.090455] 0xffffffffbf2af380
[ 60.090510] handle_bad_irq+0x0/0x2e5
[ 60.090522] ->irq_data.chip(): ffffffffbf2af380,
[ 60.090553] IRQ_NOPROBE set
[ 60.090584] ->handle_irq(): ffffffffbe2f803f,
[ 60.090590] handle_bad_irq+0x0/0x2e5
[ 60.090596] ->irq_data.chip(): ffffffffbf2af380,
[ 60.090602] 0xffffffffbf2af380
[ 60.090608] ->action(): (null)
[ 60.090779] handle_bad_irq+0x0/0x2e5
This was seen when running an upstream kernel on Acer Chromebook R11. The
system was unstable as result.
Guard the log message with __printk_ratelimit to reduce the impact. This
won't prevent the interrupt storm from happening, but at least the system
remains stable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Joe Perches <joe@perches.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Link: https://lkml.kernel.org/r/1512234784-21038-1-git-send-email-linux@roeck-us.net
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45e6ae7ef2 ]
ibmr.device is being set only after ib_alloc_mr() is
(successfully) complete. Therefore, in case mlx5_core_create_mkey()
return with error, the error flow calls mlx5_free_priv_descs()
which uses ibmr.device (which doesn't exist yet), causing
a NULL dereference oops.
To fix this, the IB device should be set in the mr struct earlier
stage (e.g. prior to calling mlx5_core_create_mkey()).
Fixes: 8a187ee52b ("IB/mlx5: Support the new memory registration API")
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2b83ff96f5 ]
With the current code, the following sequence won't work :
echo timer > trigger
echo 0 > delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
[ Upstream commit f7084059a9 ]
While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).
We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.
This patch avoids the crashes by:
* failing PCI recovery in case of nested errors (since multiple
PCI errors in a row are not expected to lead to a functional
adapter anyway), and by,
* preventing access to adapter FW when MCP is failed (we mark it as
failed when shmem cannot get initialized properly).
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e60ee41aaf ]
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4419bb1ced ]
One of AMD based server with 5762 hangs with jumbo frame traffic.
This AMD platform has southbridge limitation which is restricting MRRS
to 4000. As a work around, driver to restricts the MRRS to 2048 for
this particular 5762 NX1 card.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bbc25bee37 ]
Current MIPS64r6 toolchains aren't able to generate efficient
DMULU/DMUHU based code for the C implementation of umul_ppmm(), which
performs an unsigned 64 x 64 bit multiply and returns the upper and
lower 64-bit halves of the 128-bit result. Instead it widens the 64-bit
inputs to 128-bits and emits a __multi3 intrinsic call to perform a 128
x 128 multiply. This is both inefficient, and it results in a link error
since we don't include __multi3 in MIPS linux.
For example commit 90a53e4432 ("cfg80211: implement regdb signature
checking") merged in v4.15-rc1 recently broke the 64r6_defconfig and
64r6el_defconfig builds by indirectly selecting MPILIB. The same build
errors can be reproduced on older kernels by enabling e.g. CRYPTO_RSA:
lib/mpi/generic_mpih-mul1.o: In function `mpihelp_mul_1':
lib/mpi/generic_mpih-mul1.c:50: undefined reference to `__multi3'
lib/mpi/generic_mpih-mul2.o: In function `mpihelp_addmul_1':
lib/mpi/generic_mpih-mul2.c:49: undefined reference to `__multi3'
lib/mpi/generic_mpih-mul3.o: In function `mpihelp_submul_1':
lib/mpi/generic_mpih-mul3.c:49: undefined reference to `__multi3'
lib/mpi/mpih-div.o In function `mpihelp_divrem':
lib/mpi/mpih-div.c:205: undefined reference to `__multi3'
lib/mpi/mpih-div.c:142: undefined reference to `__multi3'
Therefore add an efficient MIPS64r6 implementation of umul_ppmm() using
inline assembly and the DMULU/DMUHU instructions, to prevent __multi3
calls being emitted.
Fixes: 7fd08ca58a ("MIPS: Add build support for the MIPS R6 ISA")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 506e8a9126 ]
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d1b8b2391c ]
When an I/O is returned with an srb_status of SRB_STATUS_INVALID_LUN
which has zero good_bytes it must be assigned an error. Otherwise the
I/O will be continuously requeued and will cause a deadlock in the case
where disks are being hot added and removed. sd_probe_async will wait
forever for its I/O to complete while holding scsi_sd_probe_domain.
Also returning the default error of DID_TARGET_FAILURE causes multipath
to not retry the I/O resulting in applications receiving I/O errors
before a failover can occur.
Signed-off-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
