[ Upstream commit 0afec5e9ce ]
When registering a new DMA MR after selecting the best aligned page size
for it, we iterate over the given sglist to split each entry to smaller,
aligned to the selected page size, DMA blocks.
In given circumstances where the sg entry and page size fit certain
sizes and the sg entry is not aligned to the selected page size, the
total size of the aligned pages we need to cover the sg entry is >= 4GB.
Under this circumstances, while iterating page aligned blocks, the
counter responsible for counting how much we advanced from the start of
the sg entry is overflowed because its type is u32 and we pass 4GB in
size. This can lead to an infinite loop inside the iterator function
because the overflow prevents the counter to be larger
than the size of the sg entry.
Fix the presented problem by changing the advancement condition to
eliminate overflow.
Backtrace:
[ 192.374329] efa_reg_user_mr_dmabuf
[ 192.376783] efa_register_mr
[ 192.382579] pgsz_bitmap 0xfffff000 rounddown 0x80000000
[ 192.386423] pg_sz [0x80000000] umem_length[0xc0000000]
[ 192.392657] start 0x0 length 0xc0000000 params.page_shift 31 params.page_num 3
[ 192.399559] hp_cnt[3], pages_in_hp[524288]
[ 192.403690] umem->sgt_append.sgt.nents[1]
[ 192.407905] number entries: [1], pg_bit: [31]
[ 192.411397] biter->__sg_nents [1] biter->__sg [0000000008b0c5d8]
[ 192.415601] biter->__sg_advance [665837568] sg_dma_len[3221225472]
[ 192.419823] biter->__sg_nents [1] biter->__sg [0000000008b0c5d8]
[ 192.423976] biter->__sg_advance [2813321216] sg_dma_len[3221225472]
[ 192.428243] biter->__sg_nents [1] biter->__sg [0000000008b0c5d8]
[ 192.432397] biter->__sg_advance [665837568] sg_dma_len[3221225472]
Fixes: a808273a49 ("RDMA/verbs: Add a DMA iterator to return aligned contiguous memory blocks")
Signed-off-by: Yonatan Nachum <ynachum@amazon.com>
Link: https://lore.kernel.org/r/20230109133711.13678-1-ynachum@amazon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1aefe5c177 ]
If you create MRs more than 0x10000 times after loading the module,
responder starts to reply NAKs for RDMA/Atomic operations because of rkey
violation detected in check_rkey(). The root cause is that rkeys are
incremented each time a new MR is created and the value overflows into the
range reserved for MWs.
This commit also increases the value of RXE_MAX_MW that has been limited
unlike other parameters.
Fixes: 0994a1bcd5 ("RDMA/rxe: Bump up default maximum values used via uverbs")
Link: https://lore.kernel.org/r/20221220080848.253785-2-matsuda-daisuke@fujitsu.com
Signed-off-by: Daisuke Matsuda <matsuda-daisuke@fujitsu.com>
Tested-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaf2213ba5 ]
If *.conf.default is updated, builtin-policy.h should be rebuilt,
but this does not work when compiled with O= option.
[Without this commit]
$ touch security/tomoyo/policy/exception_policy.conf.default
$ make O=/tmp security/tomoyo/
make[1]: Entering directory '/tmp'
GEN Makefile
CALL /home/masahiro/ref/linux/scripts/checksyscalls.sh
DESCEND objtool
make[1]: Leaving directory '/tmp'
[With this commit]
$ touch security/tomoyo/policy/exception_policy.conf.default
$ make O=/tmp security/tomoyo/
make[1]: Entering directory '/tmp'
GEN Makefile
CALL /home/masahiro/ref/linux/scripts/checksyscalls.sh
DESCEND objtool
POLICY security/tomoyo/builtin-policy.h
CC security/tomoyo/common.o
AR security/tomoyo/built-in.a
make[1]: Leaving directory '/tmp'
$(srctree)/ is essential because $(wildcard ) does not follow VPATH.
Fixes: f02dee2d14 ("tomoyo: Do not generate empty policy files")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e325285de2 ]
When unloading the SCMI core stack module, configured to use the virtio
SCMI transport, LOCKDEP reports the splat down below about unsafe locks
dependencies.
In order to avoid this possible unsafe locking scenario call upfront
virtio_break_device() before getting hold of vioch->lock.
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
6.1.0-00067-g6b934395ba07-dirty #4 Not tainted
-----------------------------------------------------
rmmod/307 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffff000080c510e0 (&dev->vqs_list_lock){+.+.}-{3:3}, at: virtio_break_device+0x28/0x68
and this task is already holding:
ffff00008288ada0 (&channels[i].lock){-.-.}-{3:3}, at: virtio_chan_free+0x60/0x168 [scmi_module]
which would create a new lock dependency:
(&channels[i].lock){-.-.}-{3:3} -> (&dev->vqs_list_lock){+.+.}-{3:3}
but this new dependency connects a HARDIRQ-irq-safe lock:
(&channels[i].lock){-.-.}-{3:3}
... which became HARDIRQ-irq-safe at:
lock_acquire+0x128/0x398
_raw_spin_lock_irqsave+0x78/0x140
scmi_vio_complete_cb+0xb4/0x3b8 [scmi_module]
vring_interrupt+0x84/0x120
vm_interrupt+0x94/0xe8
__handle_irq_event_percpu+0xb4/0x3d8
handle_irq_event_percpu+0x20/0x68
handle_irq_event+0x50/0xb0
handle_fasteoi_irq+0xac/0x138
generic_handle_domain_irq+0x34/0x50
gic_handle_irq+0xa0/0xd8
call_on_irq_stack+0x2c/0x54
do_interrupt_handler+0x8c/0x90
el1_interrupt+0x40/0x78
el1h_64_irq_handler+0x18/0x28
el1h_64_irq+0x64/0x68
_raw_write_unlock_irq+0x48/0x80
ep_start_scan+0xf0/0x128
do_epoll_wait+0x390/0x858
do_compat_epoll_pwait.part.34+0x1c/0xb8
__arm64_sys_epoll_pwait+0x80/0xd0
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.3+0x98/0x120
do_el0_svc+0x34/0xd0
el0_svc+0x40/0x98
el0t_64_sync_handler+0x98/0xc0
el0t_64_sync+0x170/0x174
to a HARDIRQ-irq-unsafe lock:
(&dev->vqs_list_lock){+.+.}-{3:3}
... which became HARDIRQ-irq-unsafe at:
...
lock_acquire+0x128/0x398
_raw_spin_lock+0x58/0x70
__vring_new_virtqueue+0x130/0x1c0
vring_create_virtqueue+0xc4/0x2b8
vm_find_vqs+0x20c/0x430
init_vq+0x308/0x390
virtblk_probe+0x114/0x9b0
virtio_dev_probe+0x1a4/0x248
really_probe+0xc8/0x3a8
__driver_probe_device+0x84/0x190
driver_probe_device+0x44/0x110
__driver_attach+0x104/0x1e8
bus_for_each_dev+0x7c/0xd0
driver_attach+0x2c/0x38
bus_add_driver+0x1e4/0x258
driver_register+0x6c/0x128
register_virtio_driver+0x2c/0x48
virtio_blk_init+0x70/0xac
do_one_initcall+0x84/0x420
kernel_init_freeable+0x2d0/0x340
kernel_init+0x2c/0x138
ret_from_fork+0x10/0x20
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->vqs_list_lock);
local_irq_disable();
lock(&channels[i].lock);
lock(&dev->vqs_list_lock);
<Interrupt>
lock(&channels[i].lock);
*** DEADLOCK ***
================
Fixes: 42e90eb53b ("firmware: arm_scmi: Add a virtio channel refcount")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221222183823.518856-6-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3d40c3ec3 ]
As the kcalloc may return NULL pointer,
it should be better to check the ishtp_dma_tx_map
before use in order to avoid NULL pointer dereference.
Fixes: 3703f53b99 ("HID: intel_ish-hid: ISH Transport layer")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10e2f328bd ]
dt_binding_check detects an issue with the pgc_hsiomix power
domain:
pgc: 'power-domains@17' does not match any of the regexes
This is because 'power-domains' should be 'power-domain'
Fixes: 2ae42e0c0b ("arm64: dts: imx8mp: add HSIO power-domains")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3b75ace20 ]
The GPC node references an interrupt parent, but it doesn't
state the interrupt itself. According to the TRM, this IRQ
is 87. This also eliminate an error detected from dt_binding_check
Fixes: fc0f051246 ("arm64: dts: imx8mp: add GPC node with GPU power domains")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21b84ebeee ]
Setting the device name after it has been registered confuses the sysfs
cleanup paths. This has already been fixed for the imx8m-blk-ctrl driver in
b64b46fbaa ("Revert "soc: imx: imx8m-blk-ctrl: set power device name""),
but the same problem exists in imx8mp-blk-ctrl.
Fixes: 556f5cf956 ("soc: imx: add i.MX8MP HSIO blk-ctrl")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b30c4b0e ]
Calling of_find_compatible_node() returns a node pointer with refcount
incremented. Use of_node_put() on it when done.
The patch fixes the same problem on different i.MX platforms.
Fixes: 8b88f7ef31 ("ARM: mx25: Retrieve IIM base from dt")
Fixes: 94b2bec1b0 ("ARM: imx27: Retrieve the SYSCTRL base address from devicetree")
Fixes: 3172225d45 ("ARM: imx31: Retrieve the IIM base address from devicetree")
Fixes: f68ea682d1 ("ARM: imx35: Retrieve the IIM base address from devicetree")
Fixes: ee18a7154e ("ARM: imx5: retrieve iim base from device tree")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62f0147fd4 ]
For clock and strobe pad of usdhc, need to config as pull down.
Current pad config set these pad as both pull up and pull down,
this is wrong, so fix it here.
Find this issue when enable HS400ES mode on one Micron eMMC chip,
CMD8 always meet CRC error in HS400ES/HS400 mode.
Fixes: e37907bd82 ("arm64: dts: freescale: add i.MX93 11x11 EVK basic support")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c620a3051 ]
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the nau8822 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is faster.
Set the MCLK at the right frequency, codec can properly use it to
generate 44.1 kHz I2S-FS.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5225ba9db1 ]
Early hardware did not support hardware handshaking on the UART, but
final production hardware did. When the hardware was updated the chip
select was changed to facilitate hardware handshaking on UART3. Fix the
ecspi2 pin mux to eliminate a pin conflict with UART3 and allow the
EEPROM to operate again.
Fixes: 4ce01ce36d ("arm64: dts: imx8mm-beacon: Enable RTS-CTS on UART3")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d1d030f00 ]
Set optional `simple-audio-card,mclk-fs` parameter to ensure a proper
clock to the wm8904 audio codec. Without this change with an audio
stream rate of 44.1 kHz the playback is completely distorted.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dfbc72256 ]
The following build warning is seen when running:
make dtbs_check DT_SCHEMA_FILES=fsl-imx-uart.yaml
arch/arm/boot/dts/imx6dl-gw560x.dtb: serial@2020000: rts-gpios: False schema does not allow [[20, 1, 0]]
From schema: Documentation/devicetree/bindings/serial/fsl-imx-uart.yaml
The imx6qdl-gw560x board does not expose the UART RTS and CTS
as native UART pins, so 'uart-has-rtscts' should not be used.
Using 'uart-has-rtscts' with 'rts-gpios' is an invalid combination
detected by serial.yaml.
Fix the problem by removing the incorrect 'uart-has-rtscts' property.
Fixes: b8a559feff ("ARM: dts: imx: add Gateworks Ventana GW5600 support")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4dd0845c4 ]
'clock_frequency' is not a valid property.
Use the correct 'clock-frequency' instead.
Fixes: 8b646cfb84 ("ARM: dts: imx7d-pico: Add support for the dwarf baseboard")
Fixes: 6418fd9241 ("ARM: dts: imx7d-pico: Add support for the nymph baseboard")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94e2cf1e0d ]
'clock_frequency' is not a valid property.
Use the correct 'clock-frequency' instead.
Fixes: 47246fafef ("ARM: dts: imx6ul-pico: Add support for the dwarf baseboard")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfd04dd1c4 ]
'regulator-compatible' is not a valid property according to
nxp,pca9450-regulator.yaml and causes the following warning:
DTC_CHK arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dtb
...
pmic@25: regulators:LDO1: Unevaluated properties are not allowed ('regulator-compatible' was unexpected)
Remove the invalid 'regulator-compatible' property.
Cc: Teresa Remmet <t.remmet@phytec.de>
Fixes: 88f7f6bcca ("arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b814eda949 ]
NXP internal information shows that the PHY refclk is gated by the
GLOBAL_TX_PIX_CLK_EN bit, so to allow the PHY PLL to lock without the
LCDIF being already active, tie this bit to the HDMI_TX_PHY power
domain.
Fixes: e3442022f5 ("soc: imx: add i.MX8MP HDMI blk-ctrl")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efab25894a ]
PSIL_EP_NATIVE endpoints may not have PEER registers for BCNT and thus
udma_decrement_byte_counters() should not try to decrement these counters.
This fixes the issue of crypto IPERF testing where the client side (EVM)
hangs without transfer of packets to the server side, seen since this
function was added.
Fixes: 7c94dcfa8f ("dmaengine: ti: k3-udma: Reset UDMA_CHAN_RT byte counters to prevent overflow")
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221128085005.489964-1-j-choudhary@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef86b2c280 ]
On newer Tegra releases, early boot SID override programming and SID
override programming during resume is handled by bootloader.
In the function tegra186_mc_program_sid() which is getting removed, SID
override register of all clients is written without checking if secure
firmware has allowed write on it or not. If write is disabled by secure
firmware then it can lead to errors coming from secure firmware and hang
in kernel boot.
Also, SID override is programmed on-demand during probe_finalize() call
of IOMMU which is done in tegra186_mc_client_sid_override() in this same
file. This function does it correctly by checking if write is permitted
on SID override register. It also checks if SID override register is
already written with correct value and skips re-writing it in that case.
Fixes: 393d66fd2c ("memory: tegra: Implement SID override programming")
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221125040752.12627-1-amhetre@nvidia.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 599d41fb8e upstream.
APR should not fail if the service device tree node does not have
the qcom,protection-domain property, since this functionality does
not exist on older platforms such as MSM8916 and MSM8996.
Ignore -EINVAL (returned when the property does not exist) to fix
a regression on 6.2-rc1 that prevents audio from working:
qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1:
Failed to read second value of qcom,protection-domain
qcom,apr remoteproc0:smd-edge.apr_audio_svc.-1.-1:
Failed to add apr 3 svc
Fixes: 6d7860f575 ("soc: qcom: apr: Add check for idr_alloc and of_property_read_string_index")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221229151648.19839-3-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55ba18dc62 upstream.
The commit 4af1b64f80 ("octeontx2-pf: Fix lmtst ID used in aura
free") uses the get/put_cpu() to protect the usage of percpu pointer
in ->aura_freeptr() callback, but it also unnecessarily disable the
preemption for the blockable memory allocation. The commit 87b93b678e
("octeontx2-pf: Avoid use of GFP_KERNEL in atomic context") tried to
fix these sleep inside atomic warnings. But it only fix the one for
the non-rt kernel. For the rt kernel, we still get the similar warnings
like below.
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by swapper/0/1:
#0: ffff800009fc5fe8 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x24/0x30
#1: ffff000100c276c0 (&mbox->lock){+.+.}-{3:3}, at: otx2_init_hw_resources+0x8c/0x3a4
#2: ffffffbfef6537e0 (&cpu_rcache->lock){+.+.}-{2:2}, at: alloc_iova_fast+0x1ac/0x2ac
Preemption disabled at:
[<ffff800008b1908c>] otx2_rq_aura_pool_init+0x14c/0x284
CPU: 20 PID: 1 Comm: swapper/0 Tainted: G W 6.2.0-rc3-rt1-yocto-preempt-rt #1
Hardware name: Marvell OcteonTX CN96XX board (DT)
Call trace:
dump_backtrace.part.0+0xe8/0xf4
show_stack+0x20/0x30
dump_stack_lvl+0x9c/0xd8
dump_stack+0x18/0x34
__might_resched+0x188/0x224
rt_spin_lock+0x64/0x110
alloc_iova_fast+0x1ac/0x2ac
iommu_dma_alloc_iova+0xd4/0x110
__iommu_dma_map+0x80/0x144
iommu_dma_map_page+0xe8/0x260
dma_map_page_attrs+0xb4/0xc0
__otx2_alloc_rbuf+0x90/0x150
otx2_rq_aura_pool_init+0x1c8/0x284
otx2_init_hw_resources+0xe4/0x3a4
otx2_open+0xf0/0x610
__dev_open+0x104/0x224
__dev_change_flags+0x1e4/0x274
dev_change_flags+0x2c/0x7c
ic_open_devs+0x124/0x2f8
ip_auto_config+0x180/0x42c
do_one_initcall+0x90/0x4dc
do_basic_setup+0x10c/0x14c
kernel_init_freeable+0x10c/0x13c
kernel_init+0x2c/0x140
ret_from_fork+0x10/0x20
Of course, we can shuffle the get/put_cpu() to only wrap the invocation
of ->aura_freeptr() as what commit 87b93b678e does. But there are only
two ->aura_freeptr() callbacks, otx2_aura_freeptr() and
cn10k_aura_freeptr(). There is no usage of perpcu variable in the
otx2_aura_freeptr() at all, so the get/put_cpu() seems redundant to it.
We can move the get/put_cpu() into the corresponding callback which
really has the percpu variable usage and avoid the sprinkling of
get/put_cpu() in several places.
Fixes: 4af1b64f80 ("octeontx2-pf: Fix lmtst ID used in aura free")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20230118071300.3271125-1-haokexin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ccc99362b upstream.
The referenced commit changed the error code returned by the kernel
when preventing a non-established socket from attaching the ktls
ULP. Before to such a commit, the user-space got ENOTCONN instead
of EINVAL.
The existing self-tests depend on such error code, and the change
caused a failure:
RUN global.non_established ...
tls.c:1673:non_established:Expected errno (22) == ENOTCONN (107)
non_established: Test failed at step #3
FAIL global.non_established
In the unlikely event existing applications do the same, address
the issue by restoring the prior error code in the above scenario.
Note that the only other ULP performing similar checks at init
time - smc_ulp_ops - also fails with ENOTCONN when trying to attach
the ULP to a non-established socket.
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2c02d41d71 ("net/ulp: prevent ULP without clone op from entering the LISTEN status")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/7bb199e7a93317fb6f8bf8b9b2dc71c18f337cde.1674042685.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
