commit 09ed259fac upstream.
VBUS should be turned off when leaving the host mode.
Set GCTL_PRTCAP to device mode in teardown to de-assert DRVVBUS pin to
turn off VBUS power.
Fixes: 5f94adfeed ("usb: dwc3: core: refactor mode initialization to its own function")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38c0d5bdf4 upstream.
Commit f4a4cbb204 ("USB: ir-usb: reimplement using generic framework")
switched to using the generic write implementation which may combine
multiple write requests into larger transfers. This can break the IrLAP
protocol where end-of-frame is determined using the USB short packet
mechanism, for example, if multiple frames are sent in rapid succession.
Fixes: f4a4cbb204 ("USB: ir-usb: reimplement using generic framework")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17a0184ca1 upstream.
Commit e0d795e4f3 ("usb: irda: cleanup on ir-usb module") added a USB
IrDA header with common defines, but mistakingly switched to using the
class-descriptor baud-rate bitmask values for the outbound header.
This broke link-speed handling for rates above 9600 baud, but a device
would also be able to operate at the default 9600 baud until a
link-speed request was issued (e.g. using the TCGETS ioctl).
Fixes: e0d795e4f3 ("usb: irda: cleanup on ir-usb module")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2988a8ae74 upstream.
Add missing endpoint sanity check to avoid dereferencing a NULL-pointer
on open() in case a device lacks a bulk-out endpoint.
Note that prior to commit f4a4cbb204 ("USB: ir-usb: reimplement using
generic framework") the oops would instead happen on open() if the
device lacked a bulk-in endpoint and on write() if it lacked a bulk-out
endpoint.
Fixes: f4a4cbb204 ("USB: ir-usb: reimplement using generic framework")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1f236efd9 upstream.
Set the MODULE_FIRMWARE for tegra186, it's registered for 124/210 and
ensures the firmware is available at the appropriate time such as in
the initrd, else if the firmware is unavailable the driver fails with
the following errors:
tegra-xusb 3530000.usb: Direct firmware load for nvidia/tegra186/xusb.bin failed with error -2
tegra-xusb 3530000.usb: failed to request firmware: -2
tegra-xusb 3530000.usb: failed to load firmware: -2
tegra-xusb: probe of 3530000.usb failed with error -2
Fixes: 5f9be5f3f8 ("usb: host: xhci-tegra: Add Tegra186 XUSB support")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200120141910.116097-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3139b18090 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b73e05aa54 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 9afac70a73 ("orinoco: add orinoco_usb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e21dba7a4d upstream.
This patch fixes 2 issues in x25_connect():
1. It makes absolutely no sense to reset the neighbour and the
connection state after a (successful) nonblocking call of x25_connect.
This prevents any connection from being established, since the response
(call accept) cannot be processed.
2. Any further calls to x25_connect() while a call is pending should
simply return, instead of creating new Call Request (on different
logical channels).
This patch should also fix the "KASAN: null-ptr-deref Write in
x25_connect" and "BUG: unable to handle kernel NULL pointer dereference
in x25_connect" bugs reported by syzbot.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reported-by: syzbot+429c200ffc8772bfe070@syzkaller.appspotmail.com
Reported-by: syzbot+eec0c87f31a7c3b66f7b@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb014de4fd upstream.
This patch introduces a list of pending module requests. This new module
list is composed of nft_module_request objects that contain the module
name and one status field that tells if the module has been already
loaded (the 'done' field).
In the first pass, from the preparation phase, the netlink command finds
that a module is missing on this list. Then, a module request is
allocated and added to this list and nft_request_module() returns
-EAGAIN. This triggers the abort path with the autoload parameter set on
from nfnetlink, request_module() is called and the module request enters
the 'done' state. Since the mutex is released when loading modules from
the abort phase, the module list is zapped so this is iteration occurs
over a local list. Therefore, the request_module() calls happen when
object lists are in consistent state (after fulling aborting the
transaction) and the commit list is empty.
On the second pass, the netlink command will find that it already tried
to load the module, so it does not request it again and
nft_request_module() returns 0. Then, there is a look up to find the
object that the command was missing. If the module was successfully
loaded, the command proceeds normally since it finds the missing object
in place, otherwise -ENOENT is reported to userspace.
This patch also updates nfnetlink to include the reason to enter the
abort phase, which is required for this new autoload module rationale.
Fixes: ec7470b834 ("netfilter: nf_tables: store transaction list locally while requesting module")
Reported-by: syzbot+29125d208b3dae9a7019@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 826035498e upstream.
This new helper function validates that unknown family and chain type
coming from userspace do not trigger an out-of-bound array access. Bail
out in case __nft_chain_type_get() returns NULL from
nft_chain_parse_hook().
Fixes: 9370761c56 ("netfilter: nf_tables: convert built-in tables/chains to chain types")
Reported-by: syzbot+156a04714799b1d480bc@syzkaller.appspotmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee8951e56c upstream.
v4l2_vbi_format, v4l2_sliced_vbi_format and v4l2_sdr_format
have a reserved array at the end that should be zeroed by drivers
as per the V4L2 spec. Older drivers often do not do this, so just
handle this in the core.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5e884b426 upstream.
add_ie_rates() copys rates without checking the length
in bss descriptor from remote AP.when victim connects to
remote attacker, this may trigger buffer overflow.
lbs_ibss_join_existing() copys rates without checking the length
in bss descriptor from remote IBSS node.when victim connects to
remote attacker, this may trigger buffer overflow.
Fix them by putting the length check before performing copy.
This fix addresses CVE-2019-14896 and CVE-2019-14897.
This also fix build warning of mixed declarations and code.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 686f85d71d upstream.
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 772f66421d upstream.
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27e0c31c5f upstream.
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89ba879e95 upstream.
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94b1663495 upstream.
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaabfd19b2 upstream.
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e311820f6 upstream.
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427db97df1 upstream.
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3885f5761 upstream.
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fedabf5a7 upstream.
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 865ad2f220 upstream.
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c6b7bcd74 upstream.
Commit 8a23eb804c ("Make filldir[64]() verify the directory entry
filename is valid") added some minimal validity checks on the directory
entries passed to filldir[64](). But they really were pretty minimal.
This fleshes out at least the name length check: we used to disallow
zero-length names, but really, negative lengths or oevr-long names
aren't ok either. Both could happen if there is some filesystem
corruption going on.
Now, most filesystems tend to use just an "unsigned char" or similar for
the length of a directory entry name, so even with a corrupt filesystem
you should never see anything odd like that. But since we then use the
name length to create the directory entry record length, let's make sure
it actually is half-way sensible.
Note how POSIX states that the size of a path component is limited by
NAME_MAX, but we actually use PATH_MAX for the check here. That's
because while NAME_MAX is generally the correct maximum name length
(it's 255, for the same old "name length is usually just a byte on
disk"), there's nothing in the VFS layer that really cares.
So the real limitation at a VFS layer is the total pathname length you
can pass as a filename: PATH_MAX.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0cb50185a upstream.
may_create_in_sticky() call is done when we already have dropped the
reference to dir.
Fixes: 30aba6656f (namei: allow restricted O_CREAT of FIFOs and regular files)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e4362d2bf upstream.
Commit 9b42c1f179 ("xfrm: Extend the output_mark") added output_mark
support but missed ESP offload support.
xfrm_smark_get() is not called within xfrm_input() for packets coming
from esp4_gro_receive() or esp6_gro_receive(). Therefore call
xfrm_smark_get() directly within these functions.
Fixes: 9b42c1f179 ("xfrm: Extend the output_mark to support input direction and masking.")
Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df2378ab0f upstream.
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9f726c942 upstream.
It used to be the case that if we got here, we wouldn't warn
but instead allocate the queue (DQA). With using the mac80211
TXQs model this changed, and we really have nothing to do with
the frame here anymore, hence the warning now.
However, clearly we missed in coding & review that this is now
a pure error path and leaks the SKB if we return 0 instead of
an indication that the SKB needs to be freed. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0695e2351 upstream.
Just as commit 0566e40ce7 ("tracing: initcall: Ordered comparison of
function pointers"), this patch fixes another remaining one in xen.h
found by clang-9.
In file included from arch/x86/xen/trace.c:21:
In file included from ./include/trace/events/xen.h:475:
In file included from ./include/trace/define_trace.h:102:
In file included from ./include/trace/trace_events.h:473:
./include/trace/events/xen.h:69:7: warning: ordered comparison of function \
pointers ('xen_mc_callback_fn_t' (aka 'void (*)(void *)') and 'xen_mc_callback_fn_t') [-Wordered-compare-function-pointers]
__field(xen_mc_callback_fn_t, fn)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/trace/trace_events.h:421:29: note: expanded from macro '__field'
^
./include/trace/trace_events.h:407:6: note: expanded from macro '__field_ext'
is_signed_type(type), filter_type); \
^
./include/linux/trace_events.h:554:44: note: expanded from macro 'is_signed_type'
^
Fixes: c796f213a6 ("xen/trace: add multicall tracing")
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e51a7dda29 upstream.
No alarm is reported by /sys/.../inX_alarm
In detail:
The SMI Voltage status register is the only register giving a status
for voltages, but it does not work like the non-SMI status registers
used for temperatures and fans.
A bit is set for each input crossing a threshold, in both direction,
but the "inside" or "outside" limits info is not available.
Also this register is cleared on read.
Note : this is not explicitly spelled out in the datasheet, but from
experiment.
As a result if an input is crossing a threshold (min or max in any
direction), the alarm is reported only once even if the input is
still outside limits. Also if the alarm for another input is read
before the one of this input, no alarm is reported at all.
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f566.tBga5POKAgHlmd0p%gilles.buloz@kontron.com
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80892772c4 upstream.
A compliation error happen when building branch 5.5-rc7
In file included from net/hsr/hsr_main.c:12:0:
net/hsr/hsr_main.h:194:20: error: two or more data types in declaration specifiers
static inline void void hsr_debugfs_rename(struct net_device *dev)
So Removed one void.
Fixes: 4c2d5e33dc ("hsr: rename debugfs file when interface name is changed")
Signed-off-by: xiaofeng.yan <yanxiaofeng7@jd.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90a8e82d3c upstream.
When switching to using generic LED name composition mechanism via
devm_led_classdev_register_ext() API the part of code initializing
struct gpio_led's template name property was removed alongside.
It was however overlooked that the property was also passed to
devm_fwnode_get_gpiod_from_child() in place of "label" parameter,
which when set to NULL, results in gpio label being initialized to '?'.
It could be observed in debugfs and failed to properly identify
gpio association with LED consumer.
Fix this shortcoming by updating the GPIO label after the LED is
registered and its final name is known.
Fixes: d7235f5fea ("leds: gpio: Use generic support for composing LED names")
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
[fixed comment]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c2659bd1d upstream.
In commit 9f79b78ef7 ("Convert filldir[64]() from __put_user() to
unsafe_put_user()") I changed filldir to not do individual __put_user()
accesses, but instead use unsafe_put_user() surrounded by the proper
user_access_begin/end() pair.
That make them enormously faster on modern x86, where the STAC/CLAC
games make individual user accesses fairly heavy-weight.
However, the user_access_begin() range was not really the exact right
one, since filldir() has the unfortunate problem that it needs to not
only fill out the new directory entry, it also needs to fix up the
previous one to contain the proper file offset.
It's unfortunate, but the "d_off" field in "struct dirent" is _not_ the
file offset of the directory entry itself - it's the offset of the next
one. So we end up backfilling the offset in the previous entry as we
walk along.
But since x86 didn't really care about the exact range, and used to be
the only architecture that did anything fancy in user_access_begin() to
begin with, the filldir[64]() changes did something lazy, and even
commented on it:
/*
* Note! This range-checks 'previous' (which may be NULL).
* The real range was checked in getdents
*/
if (!user_access_begin(dirent, sizeof(*dirent)))
goto efault;
and it all worked fine.
But now 32-bit ppc is starting to also implement user_access_begin(),
and the fact that we faked the range to only be the (possibly not even
valid) previous directory entry becomes a problem, because ppc32 will
actually be using the range that is passed in for more than just "check
that it's user space".
This is a complete rewrite of Christophe's original patch.
By saving off the record length of the previous entry instead of a
pointer to it in the filldir data structures, we can simplify the range
check and the writing of the previous entry d_off field. No need for
any conditionals in the user accesses themselves, although we retain the
conditional EINTR checking for the "was this the first directory entry"
signal handling latency logic.
Fixes: 9f79b78ef7 ("Convert filldir[64]() from __put_user() to unsafe_put_user()")
Link: https://lore.kernel.org/lkml/a02d3426f93f7eb04960a4d9140902d278cab0bb.1579697910.git.christophe.leroy@c-s.fr/
Link: https://lore.kernel.org/lkml/408c90c4068b00ea8f1c41cca45b84ec23d4946b.1579783936.git.christophe.leroy@c-s.fr/
Reported-and-tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c17bbf6c8 upstream.
init_iommu_perf_ctr() clobbers the register when it checks write access
to IOMMU perf counters and fails to restore when they are writable.
Add save and restore to fix it.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Fixes: 30861ddc9c ("perf/x86/amd: Add IOMMU Performance Counter resource management")
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab10ae1c3b upstream.
The range passed to user_access_begin() by strncpy_from_user() and
strnlen_user() starts at 'src' and goes up to the limit of userspace
although reads will be limited by the 'count' param.
On 32 bits powerpc (book3s/32) access has to be granted for each
256Mbytes segment and the cost increases with the number of segments to
unlock.
Limit the range with 'count' param.
Fixes: 594cc251fd ("make 'user_access_begin()' do 'access_ok()'")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97e24b0953 upstream.
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3111491fca upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8eeb74df5 upstream.
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 162f98dea4 ("Input: gtco - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b32391ed6 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
