commit 2859b17840 upstream.
In current spdifrx driver locks may be requested as follows:
- request lock on iec capture control, when starting synchronization.
- request lock in interrupt context, when spdifrx stop is called
from IRQ handler.
Take lock with IRQs disabled, to avoid the possible deadlock.
Lockdep report:
[ 74.278059] ================================
[ 74.282306] WARNING: inconsistent lock state
[ 74.290120] --------------------------------
...
[ 74.314373] CPU0
[ 74.314377] ----
[ 74.314381] lock(&(&spdifrx->lock)->rlock);
[ 74.314396] <Interrupt>
[ 74.314400] lock(&(&spdifrx->lock)->rlock);
Fixes: 03e4d5d56f ("ASoC: stm32: Add SPDIFRX support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20191204154333.7152-2-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c527572358 upstream.
Some adapters need a fence Work Entry to handle retransmission. Currently
the driver checks for this condition, only if the Send queue entry is
signalled. Implement the condition check, irrespective of the signalled
state of the Work queue entries
Failure to add the fence can result in access to memory that is already
marked as completed, triggering data corruption, transmission failure,
IOMMU failures, etc.
Fixes: 9152e0b722 ("RDMA/bnxt_re: HW workarounds for handling specific conditions")
Link: https://lore.kernel.org/r/1574671174-5064-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f4f199443 upstream.
In iwl_pcie_ctxt_info_gen3_init there are cases that the allocated dma
memory is leaked in case of error.
DMA memories prph_scratch, prph_info, and ctxt_info_gen3 are allocated
and initialized to be later assigned to trans_pcie. But in any error case
before such assignment the allocated memories should be released.
First of such error cases happens when iwl_pcie_init_fw_sec fails.
Current implementation correctly releases prph_scratch. But in two
sunsequent error cases where dma_alloc_coherent may fail, such
releases are missing.
This commit adds release for prph_scratch when allocation for
prph_info fails, and adds releases for prph_scratch and prph_info when
allocation for ctxt_info_gen3 fails.
Fixes: 2ee8240262 ("iwlwifi: pcie: support context information for 22560 devices")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e493173b7 upstream.
The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.
Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.
Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3499e87ea0 upstream.
clang inlines the dev_ethtool() more aggressively than gcc does, leading
to a larger amount of used stack space:
net/core/ethtool.c:2536:24: error: stack frame size of 1216 bytes in function 'dev_ethtool' [-Werror,-Wframe-larger-than=]
Marking the sub-functions that require the most stack space as
noinline_for_stack gives us reasonable behavior on all compilers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e635c2851 ]
hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: be54e7461f ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll")
Fixes: 9f3b61dc1d ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f3b61dc1d ]
When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.
Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.
Fixes: 378b80370a ("hidraw: Return EPOLLOUT from hidraw_poll")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 378b80370a ]
Always return EPOLLOUT from hidraw_poll when a device is connected.
This is safe since writes are always possible (but will always block).
hidraw does not support non-blocking writes and instead always calls
blocking backend functions on write requests. Hence, so far, a call to
poll never returned EPOLLOUT, which confuses tools like socat.
Signed-off-by: Fabian Henneke <fabian.henneke@gmail.com>
In-reply-to: <CA+hv5qkyis03CgYTWeWX9cr0my-d2Oe+aZo+mjmWRXgjrGqyrw@mail.gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc8a76a152 upstream.
Intel ID: PSIRT-TA-201910-001
CVEID: CVE-2019-14615
Intel GPU Hardware prior to Gen11 does not clear EU state
during a context switch. This can result in information
leakage between contexts.
For Gen8 and Gen9, hardware provides a mechanism for
fast cleardown of the EU state, by issuing a PIPE_CONTROL
with bit 27 set. We can use this in a context batch buffer
to explicitly cleardown the state on every context switch.
As this workaround is already in place for gen8, we can borrow
the code verbatim for Gen9.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22dad713b8 upstream.
The set uadt functions assume lineno is never NULL, but it is in
case of ip_set_utest().
syzkaller managed to generate a netlink message that calls this with
LINENO attr present:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:hash_mac4_uadt+0x1bc/0x470 net/netfilter/ipset/ip_set_hash_mac.c:104
Call Trace:
ip_set_utest+0x55b/0x890 net/netfilter/ipset/ip_set_core.c:1867
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
nfnetlink_rcv+0x1ba/0x460 net/netfilter/nfnetlink.c:563
pass a dummy lineno storage, its easier than patching all set
implementations.
This seems to be a day-0 bug.
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Reported-by: syzbot+34bd2369d38707f3f4a7@syzkaller.appspotmail.com
Fixes: a7b4f989a6 ("netfilter: ipset: IP set core support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d9a7acd3d upstream.
The timeout pointer can be NULL which means we should modify the
per-nets timeout instead.
All do this, except sctp and dccp which instead give:
general protection fault: 0000 [#1] PREEMPT SMP KASAN
net/netfilter/nf_conntrack_proto_dccp.c:682
ctnl_timeout_parse_policy+0x150/0x1d0 net/netfilter/nfnetlink_cttimeout.c:67
cttimeout_default_set+0x150/0x1c0 net/netfilter/nfnetlink_cttimeout.c:368
nfnetlink_rcv_msg+0xcf2/0xfb0 net/netfilter/nfnetlink.c:229
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
Reported-by: syzbot+46a4ad33f345d1dd346e@syzkaller.appspotmail.com
Fixes: c779e84960 ("netfilter: conntrack: remove get_timeout() indirection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b789577f6 upstream.
We get crash when the targets checkentry function tries to make
use of the network namespace pointer for arptables.
When the net pointer got added back in 2010, only ip/ip6/ebtables were
changed to initialize it, so arptables has this set to NULL.
This isn't a problem for normal arptables because no existing
arptables target has a checkentry function that makes use of par->net.
However, direct users of the setsockopt interface can provide any
target they want as long as its registered for ARP or UNPSEC protocols.
syzkaller managed to send a semi-valid arptables rule for RATEEST target
which is enough to trigger NULL deref:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
RIP: xt_rateest_tg_checkentry+0x11d/0xb40 net/netfilter/xt_RATEEST.c:109
[..]
xt_check_target+0x283/0x690 net/netfilter/x_tables.c:1019
check_target net/ipv4/netfilter/arp_tables.c:399 [inline]
find_check_entry net/ipv4/netfilter/arp_tables.c:422 [inline]
translate_table+0x1005/0x1d70 net/ipv4/netfilter/arp_tables.c:572
do_replace net/ipv4/netfilter/arp_tables.c:977 [inline]
do_arpt_set_ctl+0x310/0x640 net/ipv4/netfilter/arp_tables.c:1456
Fixes: add6746124 ("netfilter: add struct net * to target parameters")
Reported-by: syzbot+d7358a458d8a81aee898@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4acb0200ab upstream.
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2548288b4f upstream.
It turns out that even though endpoints with a maxpacket length of 0
aren't useful for data transfer, the descriptors do serve other
purposes. In particular, skipping them will also skip over other
class-specific descriptors for classes such as UVC. This unexpected
side effect has caused some UVC cameras to stop working.
In addition, the USB spec requires that when isochronous endpoint
descriptors are present in an interface's altsetting 0 (which is true
on some devices), the maxpacket size _must_ be set to 0. Warning
about such things seems like a bad idea.
This patch updates an earlier commit which would log a warning and
skip these endpoint descriptors. Now we only log a warning, and we
don't even do that for isochronous endpoints in altsetting 0.
We don't need to worry about preventing endpoints with maxpacket = 0
from ever being used for data transfers; usb_submit_urb() already
checks for this.
Reported-and-tested-by: Roger Whittaker <Roger.Whittaker@suse.com>
Fixes: d482c7bb05 ("USB: Skip endpoints with 0 maxpacket length")
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://marc.info/?l=linux-usb&m=157790377329882&w=2
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001061040270.1514-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18a1b06e5b upstream.
The open method of hiddev handler fails to bring the device out of
autosuspend state as was promised in 0361a28d3f, as it actually has 2
blocks that try to start the transport (call hid_hw_open()) with both
being guarded by the "open" counter, so the 2nd block is never executed as
the first block increments the counter so it is never at 0 when we check
it for the second block.
Additionally hiddev_open() was leaving counter incremented on errors,
causing the device to never be reopened properly if there was ever an
error.
Let's fix all of this by factoring out code that creates client structure
and powers up the device into a separate function that is being called
from usbhid_open() with the "existancelock" being held.
Fixes: 0361a28d3f ("HID: autosuspend support for USB HID")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d94a4a837 upstream.
mwifiex_process_country_ie() function parse elements of bss
descriptor in beacon packet. When processing WLAN_EID_COUNTRY
element, there is no upper limit check for country_ie_len before
calling memcpy. The destination buffer domain_info->triplet is an
array of length MWIFIEX_MAX_TRIPLET_802_11D(83). The remote
attacker can build a fake AP with the same ssid as real AP, and
send malicous beacon packet with long WLAN_EID_COUNTRY elemen
(country_ie_len > 83). Attacker can force STA connect to fake AP
on a different channel. When the victim STA connects to fake AP,
will trigger the heap buffer overflow. Fix this by checking for
length and if found invalid, don not connect to the AP.
This fix addresses CVE-2019-14895.
Reported-by: huangwen <huangwenabc@gmail.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb2b90014d upstream.
There seems to be a race condition in tty drivers and I could see on
many boot cycles a NULL pointer dereference as tty_init_dev() tries to
do 'tty->port->itty = tty' even though tty->port is NULL.
'tty->port' will be set by the driver and if the driver has not yet done
it before we open the tty device we can get to this situation. By adding
some extra debug prints, I noticed that:
6.650130: uart_add_one_port
6.663849: register_console
6.664846: tty_open
6.674391: tty_init_dev
6.675456: tty_port_link_device
uart_add_one_port() registers the console, as soon as it registers, the
userspace tries to use it and that leads to tty_open() but
uart_add_one_port() has not yet done tty_port_link_device() and so
tty->port is not yet configured when control reaches tty_init_dev().
Further look into the code and tty_port_link_device() is done by
uart_add_one_port(). After registering the console uart_add_one_port()
will call tty_port_register_device_attr_serdev() and
tty_port_link_device() is called from this.
Call add tty_port_link_device() before uart_configure_port() is done and
add a check in tty_port_link_device() so that it only links the port if
it has not been done yet.
Suggested-by: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191212131602.29504-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5ee0b3104 upstream.
Serdev sub-system claims all ACPI serial devices that are not already
initialised. As a result, no device node is created for serial ports
on certain boards such as the Apollo Lake based UP2. This has the
unintended consequence of not being able to raise the login prompt via
serial connection.
Introduce a blacklist to reject ACPI serial devices that should not be
claimed by serdev sub-system. Add the peripheral ids for Intel HS UART
to the blacklist to bring back serial port on SoCs carrying them.
Cc: stable@vger.kernel.org
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Johan Hovold <johan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191219100345.911093-1-punit1.agrawal@toshiba.co.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9d3a9cedc upstream.
The Advantech PCI-1713 has 32 analog input channels, but an incorrect
bit-mask in the definition of the `PCI171X_MUX_CHANH(x)` and
PCI171X_MUX_CHANL(x)` macros is causing channels 16 to 31 to be aliases
of channels 0 to 15. Change the bit-mask value from 0xf to 0xff to fix
it. Note that the channel numbers will have been range checked already,
so the bit-mask isn't really needed.
Fixes: 92c65e5553 ("staging: comedi: adv_pci1710: define the mux control register bits")
Reported-by: Dmytro Fil <monkdaf@gmail.com>
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191227170054.32051-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fbf7a2534 upstream.
When disconnected as USB B-device, suspend interrupt should come before
diconnect interrupt, because the DP/DM pins are shorter than the
VBUS/GND pins on the USB connectors. But we sometimes get a suspend
interrupt after disconnect interrupt. In that case we have devctl set to
99 with VBUS still valid and musb_pm_runtime_check_session() wrongly
thinks we have an active session. We have no other interrupts after
disconnect coming in this case at least with the omap2430 glue.
Let's fix the issue by checking the interrupt status again with
delayed work for the devctl 99 case. In the suspend after disconnect
case the devctl session bit has cleared by then and musb can idle.
For a typical USB B-device connect case we just continue with normal
interrupts.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2438c3a19d upstream.
Telit FN980 flashing device 0x1bc7/0x9010 requires zero packet
to be sent if out data size is is equal to the endpoint max size.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
[ johan: switch operands in conditional ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa23ca3d98 upstream.
On some laptops enabling wakeup on the GPIO interrupts used for ACPI _AEI
event handling causes spurious wakeups.
This commit adds a new honor_wakeup option, defaulting to true (our current
behavior), which can be used to disable wakeup on troublesome hardware
to avoid these spurious wakeups.
This is a workaround for an architectural problem with s2idle under Linux
where we do not have any mechanism to immediately go back to sleep after
wakeup events, other then for embedded-controller events using the standard
ACPI EC interface, for details see:
https://lore.kernel.org/linux-acpi/61450f9b-cbc6-0c09-8b3a-aff6bf9a0b3c@redhat.com/
One series of laptops which is not able to suspend without this workaround
is the HP x2 10 Cherry Trail models, this commit adds a DMI based quirk
which makes sets honor_wakeup to false on these models.
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200105160357.97154-3-hdegoede@redhat.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
