commit 74612a07b8 upstream.
There is a need for a polling interface for SRCU grace periods. This
polling needs to distinguish between an SRCU instance being idle on the
one hand or in the middle of a grace period on the other. This commit
therefore converts the Tiny SRCU srcu_struct structure's srcu_idx from
a defacto boolean to a free-running counter, using the bottom bit to
indicate that a grace period is in progress. The second-from-bottom
bit is thus used as the index returned by srcu_read_lock().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Fix ->srcu_lock_nesting[] indexing per Neeraj Upadhyay. ]
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a893c711a upstream.
There is a need for a polling interface for SRCU grace periods.
This polling needs to initiate an SRCU grace period without
having to queue (and manage) a callback. This commit therefore
splits the Tiny SRCU call_srcu() function into callback-queuing and
start-grace-period portions, with the latter in a new function named
srcu_gp_start_if_needed().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5358c9fa54 upstream.
There is a need for a polling interface for SRCU grace
periods, so this commit supplies get_state_synchronize_srcu(),
start_poll_synchronize_srcu(), and poll_state_synchronize_srcu() for this
purpose. The first can be used if future grace periods are inevitable
(perhaps due to a later call_srcu() invocation), the second if future
grace periods might not otherwise happen, and the third to check if a
grace period has elapsed since the corresponding call to either of the
first two.
As with get_state_synchronize_rcu() and cond_synchronize_rcu(),
the return value from either get_state_synchronize_srcu() or
start_poll_synchronize_srcu() must be passed in to a later call to
poll_state_synchronize_srcu().
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
[ paulmck: Add EXPORT_SYMBOL_GPL() per kernel test robot feedback. ]
[ paulmck: Apply feedback from Neeraj Upadhyay. ]
Link: https://lore.kernel.org/lkml/20201117004017.GA7444@paulmck-ThinkPad-P72/
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29d2bb94a8 upstream.
There is a need for a polling interface for SRCU grace periods.
This polling needs to initiate an SRCU grace period without having
to queue (and manage) a callback. This commit therefore splits the
Tree SRCU __call_srcu() function into callback-initialization and
queuing/start-grace-period portions, with the latter in a new function
named srcu_gp_start_if_needed(). This function may be passed a NULL
callback pointer, in which case it will refrain from queuing anything.
Why have the new function mess with queuing? Locking considerations,
of course!
Link: https://lore.kernel.org/rcu/20201112201547.GF3365678@moria.home.lan/
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f66de7ac48 upstream.
The power_pmu_event_init() callback access per-cpu variable
(cpu_hw_events) to check for event constraints and Branch Stack
(BHRB). Current usage is to disable preemption when accessing the
per-cpu variable, but this does not prevent timer callback from
interrupting event_init. Fix this by using 'local_irq_save/restore'
to make sure the code path is invoked with disabled interrupts.
This change is tested in mambo simulator to ensure that, if a timer
interrupt comes in during the per-cpu access in event_init, it will be
soft masked and replayed later. For testing purpose, introduced a
udelay() in power_pmu_event_init() to make sure a timer interrupt arrives
while in per-cpu variable access code between local_irq_save/resore.
As expected the timer interrupt was replayed later during local_irq_restore
called from power_pmu_event_init. This was confirmed by adding
breakpoint in mambo and checking the backtrace when timer_interrupt
was hit.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1606814880-1720-1-git-send-email-atrajeev@linux.vnet.ibm.com
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f0e6edcd9 upstream.
Considering the following testcase:
int
foo(int a, int b)
{
for (unsigned i = 0; i < 1000000000; i++)
a += b;
return a;
}
int main()
{
foo (3, 4);
return 0;
}
'perf annotate' displays:
86.52 │40055e: → ja 40056c <foo(int, int)+0x26>
13.37 │400560: mov -0x18(%rbp),%eax
│400563: add %eax,-0x14(%rbp)
│400566: addl $0x1,-0x4(%rbp)
0.11 │40056a: → jmp 400557 <foo(int, int)+0x11>
│40056c: mov -0x14(%rbp),%eax
│40056f: pop %rbp
and the 'ja 40056c' does not link to the location in the function. It's
caused by fact that comma is wrongly parsed, it's part of function
signature.
With my patch I see:
86.52 │ ┌──ja 26
13.37 │ │ mov -0x18(%rbp),%eax
│ │ add %eax,-0x14(%rbp)
│ │ addl $0x1,-0x4(%rbp)
0.11 │ │↑ jmp 11
│26:└─→mov -0x14(%rbp),%eax
and 'o' output prints:
86.52 │4005┌── ↓ ja 40056c <foo(int, int)+0x26>
13.37 │4005│0: mov -0x18(%rbp),%eax
│4005│3: add %eax,-0x14(%rbp)
│4005│6: addl $0x1,-0x4(%rbp)
0.11 │4005│a: ↑ jmp 400557 <foo(int, int)+0x11>
│4005└─→ mov -0x14(%rbp),%eax
On the contrary, compiling the very same file with gcc -x c, the parsing
is fine because function arguments are not displayed:
jmp 400543 <foo+0x1d>
Committer testing:
Before:
$ cat cpp_args_annotate.c
int
foo(int a, int b)
{
for (unsigned i = 0; i < 1000000000; i++)
a += b;
return a;
}
int main()
{
foo (3, 4);
return 0;
}
$ gcc --version |& head -1
gcc (GCC) 10.2.1 20201125 (Red Hat 10.2.1-9)
$ gcc -g cpp_args_annotate.c -o cpp_args_annotate
$ perf record ./cpp_args_annotate
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.275 MB perf.data (7188 samples) ]
$ perf annotate --stdio2 foo
Samples: 7K of event 'cycles:u', 4000 Hz, Event count (approx.): 7468429289, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo>:
foo():
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
↓ jmp 1d
a += b;
13.45 13: mov -0x18(%rbp),%eax
add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.09 1d: cmpl $0x3b9ac9ff,-0x4(%rbp)
86.46 ↑ jbe 13
return a;
mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
I.e. works for C, now lets switch to C++:
$ g++ -g cpp_args_annotate.c -o cpp_args_annotate
$ perf record ./cpp_args_annotate
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.268 MB perf.data (6976 samples) ]
$ perf annotate --stdio2 foo
Samples: 6K of event 'cycles:u', 4000 Hz, Event count (approx.): 7380681761, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo(int, int)>:
foo(int, int):
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
cmpl $0x3b9ac9ff,-0x4(%rbp)
86.53 → ja 40112c <foo(int, int)+0x26>
a += b;
13.32 mov -0x18(%rbp),%eax
0.00 add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.15 → jmp 401117 <foo(int, int)+0x11>
return a;
mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
Reproduced.
Now with this patch:
Reusing the C++ built binary, as we can see here:
$ readelf -wi cpp_args_annotate | grep producer
<c> DW_AT_producer : (indirect string, offset: 0x2e): GNU C++14 10.2.1 20201125 (Red Hat 10.2.1-9) -mtune=generic -march=x86-64 -g
$
And furthermore:
$ file cpp_args_annotate
cpp_args_annotate: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, BuildID[sha1]=4fe3cab260204765605ec630d0dc7a7e93c361a9, for GNU/Linux 3.2.0, with debug_info, not stripped
$ perf buildid-list -i cpp_args_annotate
4fe3cab260204765605ec630d0dc7a7e93c361a9
$ perf buildid-list | grep cpp_args_annotate
4fe3cab260204765605ec630d0dc7a7e93c361a9 /home/acme/c/cpp_args_annotate
$
It now works:
$ perf annotate --stdio2 foo
Samples: 6K of event 'cycles:u', 4000 Hz, Event count (approx.): 7380681761, [percent: local period]
foo() /home/acme/c/cpp_args_annotate
Percent
0000000000401106 <foo(int, int)>:
foo(int, int):
int
foo(int a, int b)
{
push %rbp
mov %rsp,%rbp
mov %edi,-0x14(%rbp)
mov %esi,-0x18(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
movl $0x0,-0x4(%rbp)
11: cmpl $0x3b9ac9ff,-0x4(%rbp)
86.53 ↓ ja 26
a += b;
13.32 mov -0x18(%rbp),%eax
0.00 add %eax,-0x14(%rbp)
for (unsigned i = 0; i < 1000000000; i++)
addl $0x1,-0x4(%rbp)
0.15 ↑ jmp 11
return a;
26: mov -0x14(%rbp),%eax
}
pop %rbp
← retq
$
Signed-off-by: Martin Liška <mliska@suse.cz>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Link: http://lore.kernel.org/lkml/13e1a405-edf9-e4c2-4327-a9b454353730@suse.cz
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41d5854113 upstream.
I got several memory leak reports from Asan with a simple command. It
was because VDSO is not released due to the refcount. Like in
__dsos_addnew_id(), it should put the refcount after adding to the list.
$ perf record true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.030 MB perf.data (10 samples) ]
=================================================================
==692599==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 439 byte(s) in 1 object(s) allocated from:
#0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
#1 0x559bce4aa8ee in dso__new_id util/dso.c:1256
#2 0x559bce59245a in __machine__addnew_vdso util/vdso.c:132
#3 0x559bce59245a in machine__findnew_vdso util/vdso.c:347
#4 0x559bce50826c in map__new util/map.c:175
#5 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787
#6 0x559bce512f6b in machines__deliver_event util/session.c:1481
#7 0x559bce515107 in perf_session__deliver_event util/session.c:1551
#8 0x559bce51d4d2 in do_flush util/ordered-events.c:244
#9 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323
#10 0x559bce519bea in __perf_session__process_events util/session.c:2268
#11 0x559bce519bea in perf_session__process_events util/session.c:2297
#12 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017
#13 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234
#14 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026
#15 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858
#16 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313
#17 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365
#18 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409
#19 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539
#20 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308
Indirect leak of 32 byte(s) in 1 object(s) allocated from:
#0 0x7fea52341037 in __interceptor_calloc ../../../../src/libsanitizer/asan/asan_malloc_linux.cpp:154
#1 0x559bce520907 in nsinfo__copy util/namespaces.c:169
#2 0x559bce50821b in map__new util/map.c:168
#3 0x559bce503c92 in machine__process_mmap2_event util/machine.c:1787
#4 0x559bce512f6b in machines__deliver_event util/session.c:1481
#5 0x559bce515107 in perf_session__deliver_event util/session.c:1551
#6 0x559bce51d4d2 in do_flush util/ordered-events.c:244
#7 0x559bce51d4d2 in __ordered_events__flush util/ordered-events.c:323
#8 0x559bce519bea in __perf_session__process_events util/session.c:2268
#9 0x559bce519bea in perf_session__process_events util/session.c:2297
#10 0x559bce2e7a52 in process_buildids /home/namhyung/project/linux/tools/perf/builtin-record.c:1017
#11 0x559bce2e7a52 in record__finish_output /home/namhyung/project/linux/tools/perf/builtin-record.c:1234
#12 0x559bce2ed4f6 in __cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2026
#13 0x559bce2ed4f6 in cmd_record /home/namhyung/project/linux/tools/perf/builtin-record.c:2858
#14 0x559bce422db4 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:313
#15 0x559bce2acac8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:365
#16 0x559bce2acac8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:409
#17 0x559bce2acac8 in main /home/namhyung/project/linux/tools/perf/perf.c:539
#18 0x7fea51e76d09 in __libc_start_main ../csu/libc-start.c:308
SUMMARY: AddressSanitizer: 471 byte(s) leaked in 2 allocation(s).
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210315045641.700430-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67069a1f0f upstream.
ASan reported a memory leak caused by info_linear not being deallocated.
The info_linear was allocated during in perf_event__synthesize_one_bpf_prog().
This patch adds the corresponding free() when bpf_prog_info_node
is freed in perf_env__purge_bpf().
$ sudo ./perf record -- sleep 5
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.025 MB perf.data (8 samples) ]
=================================================================
==297735==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 7688 byte(s) in 19 object(s) allocated from:
#0 0x4f420f in malloc (/home/user/linux/tools/perf/perf+0x4f420f)
#1 0xc06a74 in bpf_program__get_prog_info_linear /home/user/linux/tools/lib/bpf/libbpf.c:11113:16
#2 0xb426fe in perf_event__synthesize_one_bpf_prog /home/user/linux/tools/perf/util/bpf-event.c:191:16
#3 0xb42008 in perf_event__synthesize_bpf_events /home/user/linux/tools/perf/util/bpf-event.c:410:9
#4 0x594596 in record__synthesize /home/user/linux/tools/perf/builtin-record.c:1490:8
#5 0x58c9ac in __cmd_record /home/user/linux/tools/perf/builtin-record.c:1798:8
#6 0x58990b in cmd_record /home/user/linux/tools/perf/builtin-record.c:2901:8
#7 0x7b2a20 in run_builtin /home/user/linux/tools/perf/perf.c:313:11
#8 0x7b12ff in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8
#9 0x7b2583 in run_argv /home/user/linux/tools/perf/perf.c:409:2
#10 0x7b0d79 in main /home/user/linux/tools/perf/perf.c:539:3
#11 0x7fa357ef6b74 in __libc_start_main /usr/src/debug/glibc-2.33-8.fc34.x86_64/csu/../csu/libc-start.c:332:16
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Link: http://lore.kernel.org/lkml/20210602224024.300485-1-rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55981d3541 upstream.
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Fixes: e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Jonathan Lampérth <jon@h4n.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7387a72c5f upstream.
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new generic NAND ECC framework stores the configuration and
requirements in separate places since commit 93ef92f6f4 ("mtd: nand: Use
the new generic ECC object"). In 5.10.x The SPI NAND layer still uses only
the requirements to track the ECC properties. This mismatch leads to
values of zero being used for ECC strength and step_size in the SPI NAND
layer wherever nanddev_get_ecc_conf() is used and therefore breaks the SPI
NAND on-die ECC support in 5.10.x.
By using nanddev_get_ecc_requirements() instead of nanddev_get_ecc_conf()
for SPI NAND, we make sure that the correct parameters for the detected
chip are used. In later versions (5.11.x) this is fixed anyway with the
implementation of the SPI NAND on-die ECC engine.
Cc: stable@vger.kernel.org # 5.10.x
Reported-by: voice INTER connect GmbH <developer@voiceinterconnect.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe67f4dd8d upstream.
It turns out that the SIGIO/FASYNC situation is almost exactly the same
as the EPOLLET case was: user space really wants to be notified after
every operation.
Now, in a perfect world it should be sufficient to only notify user
space on "state transitions" when the IO state changes (ie when a pipe
goes from unreadable to readable, or from unwritable to writable). User
space should then do as much as possible - fully emptying the buffer or
what not - and we'll notify it again the next time the state changes.
But as with EPOLLET, we have at least one case (stress-ng) where the
kernel sent SIGIO due to the pipe being marked for asynchronous
notification, but the user space signal handler then didn't actually
necessarily read it all before returning (it read more than what was
written, but since there could be multiple writes, it could leave data
pending).
The user space code then expected to get another SIGIO for subsequent
writes - even though the pipe had been readable the whole time - and
would only then read more.
This is arguably a user space bug - and Colin King already fixed the
stress-ng code in question - but the kernel regression rules are clear:
it doesn't matter if kernel people think that user space did something
silly and wrong. What matters is that it used to work.
So if user space depends on specific historical kernel behavior, it's a
regression when that behavior changes. It's on us: we were silly to
have that non-optimal historical behavior, and our old kernel behavior
was what user space was tested against.
Because of how the FASYNC notification was tied to wakeup behavior, this
was first broken by commits f467a6a664 and 1b6b26ae70 ("pipe: fix
and clarify pipe read/write wakeup logic"), but at the time it seems
nobody noticed. Probably because the stress-ng problem case ends up
being timing-dependent too.
It was then unwittingly fixed by commit 3a34b13a88 ("pipe: make pipe
writes always wake up readers") only to be broken again when by commit
3b844826b6 ("pipe: avoid unnecessary EPOLLET wakeups under normal
loads").
And at that point the kernel test robot noticed the performance
refression in the stress-ng.sigio.ops_per_sec case. So the "Fixes" tag
below is somewhat ad hoc, but it matches when the issue was noticed.
Fix it for good (knock wood) by simply making the kill_fasync() case
separate from the wakeup case. FASYNC is quite rare, and we clearly
shouldn't even try to use the "avoid unnecessary wakeups" logic for it.
Link: https://lore.kernel.org/lkml/20210824151337.GC27667@xsang-OptiPlex-9020/
Fixes: 3b844826b6 ("pipe: avoid unnecessary EPOLLET wakeups under normal loads")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Oliver Sang <oliver.sang@intel.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b844826b6 upstream.
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88 ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/
Fixes: 3a34b13a88 ("pipe: make pipe writes always wake up readers")
Reported-by: kernel test robot <oliver.sang@intel.com>
Tested-by: Sandeep Patil <sspatil@android.com>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc0939fcfa upstream.
We have a race between marking that an inode needs to be logged, either
at btrfs_set_inode_last_trans() or at btrfs_page_mkwrite(), and between
btrfs_sync_log(). The following steps describe how the race happens.
1) We are at transaction N;
2) Inode I was previously fsynced in the current transaction so it has:
inode->logged_trans set to N;
3) The inode's root currently has:
root->log_transid set to 1
root->last_log_commit set to 0
Which means only one log transaction was committed to far, log
transaction 0. When a log tree is created we set ->log_transid and
->last_log_commit of its parent root to 0 (at btrfs_add_log_tree());
4) One more range of pages is dirtied in inode I;
5) Some task A starts an fsync against some other inode J (same root), and
so it joins log transaction 1.
Before task A calls btrfs_sync_log()...
6) Task B starts an fsync against inode I, which currently has the full
sync flag set, so it starts delalloc and waits for the ordered extent
to complete before calling btrfs_inode_in_log() at btrfs_sync_file();
7) During ordered extent completion we have btrfs_update_inode() called
against inode I, which in turn calls btrfs_set_inode_last_trans(),
which does the following:
spin_lock(&inode->lock);
inode->last_trans = trans->transaction->transid;
inode->last_sub_trans = inode->root->log_transid;
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
So ->last_trans is set to N and ->last_sub_trans set to 1.
But before setting ->last_log_commit...
8) Task A is at btrfs_sync_log():
- it increments root->log_transid to 2
- starts writeback for all log tree extent buffers
- waits for the writeback to complete
- writes the super blocks
- updates root->last_log_commit to 1
It's a lot of slow steps between updating root->log_transid and
root->last_log_commit;
9) The task doing the ordered extent completion, currently at
btrfs_set_inode_last_trans(), then finally runs:
inode->last_log_commit = inode->root->last_log_commit;
spin_unlock(&inode->lock);
Which results in inode->last_log_commit being set to 1.
The ordered extent completes;
10) Task B is resumed, and it calls btrfs_inode_in_log() which returns
true because we have all the following conditions met:
inode->logged_trans == N which matches fs_info->generation &&
inode->last_subtrans (1) <= inode->last_log_commit (1) &&
inode->last_subtrans (1) <= root->last_log_commit (1) &&
list inode->extent_tree.modified_extents is empty
And as a consequence we return without logging the inode, so the
existing logged version of the inode does not point to the extent
that was written after the previous fsync.
It should be impossible in practice for one task be able to do so much
progress in btrfs_sync_log() while another task is at
btrfs_set_inode_last_trans() right after it reads root->log_transid and
before it reads root->last_log_commit. Even if kernel preemption is enabled
we know the task at btrfs_set_inode_last_trans() can not be preempted
because it is holding the inode's spinlock.
However there is another place where we do the same without holding the
spinlock, which is in the memory mapped write path at:
vm_fault_t btrfs_page_mkwrite(struct vm_fault *vmf)
{
(...)
BTRFS_I(inode)->last_trans = fs_info->generation;
BTRFS_I(inode)->last_sub_trans = BTRFS_I(inode)->root->log_transid;
BTRFS_I(inode)->last_log_commit = BTRFS_I(inode)->root->last_log_commit;
(...)
So with preemption happening after setting ->last_sub_trans and before
setting ->last_log_commit, it is less of a stretch to have another task
do enough progress at btrfs_sync_log() such that the task doing the memory
mapped write ends up with ->last_sub_trans and ->last_log_commit set to
the same value. It is still a big stretch to get there, as the task doing
btrfs_sync_log() has to start writeback, wait for its completion and write
the super blocks.
So fix this in two different ways:
1) For btrfs_set_inode_last_trans(), simply set ->last_log_commit to the
value of ->last_sub_trans minus 1;
2) For btrfs_page_mkwrite() only set the inode's ->last_sub_trans, just
like we do for buffered and direct writes at btrfs_file_write_iter(),
which is all we need to make sure multiple writes and fsyncs to an
inode in the same transaction never result in an fsync missing that
the inode changed and needs to be logged. Turn this into a helper
function and use it both at btrfs_page_mkwrite() and at
btrfs_file_write_iter() - this also fixes the problem that at
btrfs_page_mkwrite() we were setting those fields without the
protection of the inode's spinlock.
This is an extremely unlikely race to happen in practice.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb4b1373dc ]
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6eaa1f3c59 ]
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0b1ef5f7 ]
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812194917.1703356-1-markyacoub@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37110237f3 ]
Avoiding qed ll2 race condition and NULL pointer dereference as part
of the remove and recovery flows.
Changes form V1:
- Change (!p_rx->set_prod_addr).
- qed_ll2.c checkpatch fixes.
Change from V2:
- Revert "qed_ll2.c checkpatch fixes".
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a24ce06c70 ]
We use a spinlock now so add a stub.
Ignore bogus uninitialized variable warnings.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e74cfa91f4 ]
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43bb40c5b9 ]
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
kernel:watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [kworker/1:1:27059]
watchdog: BUG: soft lockup - CPU#1 stuck for 52s! [kworker/1:1:27059]
CPU: 1 PID: 27059 Comm: kworker/1:1 Tainted: G S W I L 5.13.0-hotplug+ #8
Hardware name: Dell Inc. PowerEdge R640/0H28RR, BIOS 2.9.4 11/06/2020
Workqueue: events linkwatch_event
RIP: 0010:virtnet_send_command+0xfc/0x150 [virtio_net]
Call Trace:
virtnet_set_rx_mode+0xcf/0x2a7 [virtio_net]
? __hw_addr_create_ex+0x85/0xc0
__dev_mc_add+0x72/0x80
igmp6_group_added+0xa7/0xd0
ipv6_mc_up+0x3c/0x60
ipv6_find_idev+0x36/0x80
addrconf_add_dev+0x1e/0xa0
addrconf_dev_config+0x71/0x130
addrconf_notify+0x1f5/0xb40
? rtnl_is_locked+0x11/0x20
? __switch_to_asm+0x42/0x70
? finish_task_switch+0xaf/0x2c0
? raw_notifier_call_chain+0x3e/0x50
raw_notifier_call_chain+0x3e/0x50
netdev_state_change+0x67/0x90
linkwatch_do_dev+0x3c/0x50
__linkwatch_run_queue+0xd2/0x220
linkwatch_event+0x21/0x30
process_one_work+0x1c8/0x370
worker_thread+0x30/0x380
? process_one_work+0x370/0x370
kthread+0x118/0x140
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
Hence, add the ability to abort the command on surprise removal
which prevents infinite loop and system lockup.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-5-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60f0779862 ]
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Link: https://lore.kernel.org/r/20210721142648.1525924-2-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 335ffab3ef ]
This WARN can be triggered per-core and the stack trace is not useful.
Replace it with plain dev_err(). Fix a comment while at it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1669a941f7 ]
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: a20a40a8bb ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b3a8738b7 ]
The u32 variable pci_dword is being masked with 0x1fffffff and then left
shifted 23 places. The shift is a u32 operation,so a value of 0x200 or
more in pci_dword will overflow the u32 and only the bottow 32 bits
are assigned to addr. I don't believe this was the original intent.
Fix this by casting pci_dword to a resource_size_t to ensure no
overflow occurs.
Note that the mask and 12 bit left shift operation does not need this
because the mask SNR_IMC_MMIO_MEM0_MASK and shift is always a 32 bit
value.
Fixes: ee49532b38 ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Addresses-Coverity: ("Unintentional integer overflow")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Link: https://lore.kernel.org/r/20210706114553.28249-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c8094e394 ]
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
Fixes: 993dcfac64 ("dt-bindings: riscv: sifive-l2-cache: convert bindings to json-schema")
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82a44ae113 ]
In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.
Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.
The following kernel panic is observed without this patch:
RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2aae654a4 ]
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 885814a97f ]
This reverts commit 419dd626e3.
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Fixes: 419dd626e3 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c1671e0d1 ]
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94391fae82 ]
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a96d9330b0 ]
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fc ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a6d281946 ]
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96a6b93b69 ]
Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.
Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.
Before:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: Invalid argument
After:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: File exists
The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.
For example, __rtnl_newlink() does this:
net/core/rtnetlink.c
3270 char ifname[IFNAMSIZ];
...
3286 if (tb[IFLA_IFNAME])
3287 nla_strscpy(ifname, tb[IFLA_IFNAME], IFNAMSIZ);
3288 else
3289 ifname[0] = '\0';
...
3364 if (dev) {
...
3394 return do_setlink(skb, dev, ifm, extack, tb, ifname, status);
3395 }
, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.
But the pat (pattern) in __dev_change_net_namespace() is used as:
net/core/dev.c
11198 err = -EEXIST;
11199 if (__dev_get_by_name(net, dev->name)) {
11200 /* We get here if we can't use the current device name */
11201 if (!pat)
11202 goto out;
11203 err = dev_get_valid_name(net, dev, pat);
11204 if (err < 0)
11205 goto out;
11206 }
As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.
Fixes: d8a5ec6727 ("[NET]: netlink support for moving devices between network namespaces.")
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43fed4d48d ]
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
