A PCI device is "external_facing" if it's a Root Port with the ACPI
"ExternalFacingPort" property or if it has the DT "external-facing"
property. We consider everything downstream from such a device to
be removable by user.
We're mainly concerned with consumer platforms with user accessible
Thunderbolt ports that are vulnerable to DMA attacks, and we expect those
ports to be identified by firmware as "ExternalFacingPort". Devices in
traditional hotplug slots can technically be removed, but the expectation
is that unless the port is marked with "ExternalFacingPort", such devices
are less accessible to user / may not be removed by end user, and thus not
exposed as "removable" to userspace.
This can be used to implement userspace policies tailored for
user removable devices. Eg usage:
https://chromium-review.googlesource.com/c/chromiumos/platform2/+/2591812https://chromium-review.googlesource.com/c/chromiumos/platform2/+/2795038
(code uses such an attribute to remove external PCI devices or disable
features on them as needed by the policy desired)
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-2-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the "removable" attribute from USB to core in order to allow it to be
supported by other subsystem / buses. Individual buses that want to support
this attribute can populate the removable property of the device while
enumerating it with the 3 possible values -
- "unknown"
- "fixed"
- "removable"
Leaving the field unchanged (i.e. "not supported") would mean that the
attribute would not show up in sysfs for that device. The UAPI (location,
symantics etc) for the attribute remains unchanged.
Move the "removable" attribute from USB to the device core so it can be
used by other subsystems / buses.
By default, devices do not have a "removable" attribute in sysfs.
If a subsystem or bus driver wants to support a "removable" attribute, it
should call device_set_removable() before calling device_register() or
device_add(), e.g.:
device_set_removable(dev, DEVICE_REMOVABLE);
device_register(dev);
The possible values and the resulting sysfs attribute contents are:
DEVICE_REMOVABLE_UNKNOWN -> "unknown"
DEVICE_REMOVABLE -> "removable"
DEVICE_FIXED -> "fixed"
Convert the USB "removable" attribute to use this new device core
functionality. There should be no user-visible change in the location or
semantics of attribute for USB devices.
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-1-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/gadget/udc/trace files follows this syntax, but
the content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc.
For e.g., running scripts/kernel-doc -none drivers/usb/gadget/udc/trace.h
emits:
warning: expecting prototype for udc.c(). Prototype was for TRACE_SYSTEM() instead
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210522115227.9977-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a control URB is submitted, the direction indicated by URB's pipe
member is supposed to match the direction indicated by the setup
packet's bRequestType member. A mismatch could lead to trouble,
depending on which field the host controller drivers use for
determining the actual direction.
This shouldn't ever happen; it would represent a careless bug in a
kernel driver somewhere. This patch adds a dev_WARN_ONCE to let
people know about the potential problem.
Suggested-by: "Geoffrey D. Bennett" <g@b4.vu>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210522021623.GB1260282@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When vbus auto discharge is enabled, TCPCI based TCPC transitions
into Attached.SNK/Attached.SRC state. During PR_SWAP, TCPCI based
TCPC would disconnect when partner changes power roles. TCPC has
to be moved APPLY RC state during PR_SWAP. This is done by
ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. Once the swap sequence
is done, AutoDischargeDisconnect is re-enabled.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210517192112.40934-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1763 have some differences from the isp1760, 8 bit address for
registers and 16 bit for values, no bulk access to memory addresses,
16 PTD's instead of 32.
Following the regmap work done before add the registers, memory access
and add the functions to support differences in setup sequences.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-8-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a lot of pre-existing typechecking warnings around the
access and assign of elements of ptd structure of __dw type.
sparse: warning: invalid assignment: |=
sparse: left side has type restricted __dw
sparse: right side has type unsigned int
or
warning: restricted __dw degrades to integer
or
sparse: warning: incorrect type in assignment (different base types)
sparse: expected restricted __dw [usertype] dw4
sparse: got unsigned int [assigned] [usertype] usof
To handle this, annotate conversions along the {TO,FROM}_DW* macros
and some assignments and function arguments.
This clean up completely all sparse warnings for this driver.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-2-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On start-up, we can get a spurious session request interrupt with nothing
connected. After that the devctl session bit will silently clear, but the
musb hardware is never idled until a cable is plugged in, or the glue
layer module is reloaded.
Let's just check the session bit again in 3 seconds in peripheral mode
to catch the issue.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210518150615.53464-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like we are missing suspend and resume functions for pm_ops that
are needed to idle the hardware for system suspend for 2430 glue layer.
We can rely on the driver internal PM runtime state, and call driver
functions to idle the hardware on suspend if needed. There is no need
to add a dependency to PM runtime for system suspend here.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210518074449.17070-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows
that, in the worse scenario, could lead to heap overflows.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210513193353.GA196565@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
