Currently, other paths calling drv_sta_state() hold the mutex
and therefore drivers can assume that, and look at links with
that protection. Fix that for the reconfig path as well; to
do it more easily use ieee80211_reconfig_stations() for the
AP/AP_VLAN station reconfig as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an MLD address attribute to BSS entries that the interface
is currently associated with to help userspace figure out what's
going on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Catch the bugs fixed in mac80211 by the previous commits
and warn if an invalid address is added (or removed).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we stop a not-yet-started scan, we erroneously call
into the driver, causing a sequence of sw_scan_start()
followed by sw_scan_complete() twice. This will cause a
warning in hwsim with next in line commit that validates
the address passed to wmediumd/virtio. Fix this by doing
the calls only if we were actually scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Right now, we assign the link address only after we add
the link to the driver, which is quite obviously wrong.
It happens to work in many cases because it gets updated
immediately, and then link_conf updates may update it,
but it's clearly not really right.
Set the link address during ieee80211_mgd_setup_link()
so it's set before telling the driver about the link.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We probably should've done that originally, we already have
about 300 lines of code there, and will add more. Move all
the link code we wrote to a new file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor some common RX functionality between the netlink
and non-netlink paths, adding the special hwsim TLV (if
compiled) also in the netlink path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just as an additional check that mac80211 isn't doing
anything strange, add a check of the STA magic (which
gets assigned when the station is added, and cleared
when the station is removed).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need the sdata argument, and it doesn't make any
sense for a direct conversion from one value to another,
so just remove the argument
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have proper multicast TX in mac80211, there's
no longer a need to fake something here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return value from rdev_set_mcast_rate() directly instead of
taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adds support in mac80211 for NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE.
The motivation behind this functionality is to fix limitations of
address randomization on frequencies which are disallowed in world
roaming.
The way things work now, if a client wants to randomize their address
per-connection it must power down the device, change the MAC, and
power back up. Here lies a problem since powering down the device
may result in frequencies being disabled (until the regdom is set).
If the desired BSS is on one such frequency the client is unable to
connect once the phy is powered again.
For mac80211 based devices changing the MAC while powered is possible
but currently disallowed (-EBUSY). This patch adds some logic to
allow a MAC change while powered by removing the interface, changing
the MAC, and adding it again. mac80211 will advertise support for
this feature so userspace can determine the best course of action e.g.
disallow address randomization on certain frequencies if not
supported.
There are certain limitations put on this which simplify the logic:
- No active connection
- No offchannel work, including scanning.
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new extended feature bit signifying that the wireless hardware
supports changing the MAC address while the underlying net_device is
powered. Note that this has a different meaning from
IFF_LIVE_ADDR_CHANGE as additional restrictions might be imposed by
the hardware, such as:
- No connection is active on this interface, carrier is off
- No scan is in progress
- No offchannel operations are in progress
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We turn off interrupt in ISR, and re-enable interrupt in threadfn or
napi_poll according to the mode it stays. If we are turning off interrupt,
rtwpci->running flag is unset and interrupt handler stop processing even
if it was called, so disallow to re-enable interrupt in this situation.
Or, wifi chip doesn't trigger interrupt events anymore because interrupt
status (ISR) isn't clear by interrupt handler anymore.
Fixes: c83dcd0508 ("rtw89: pci: add a separate interrupt handler for low power mode")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220824063312.15784-1-pkshih@realtek.com
When starting to send heavy traffic in low power mode,
driver will call multiple tx wake notify to wake firmware
within a short time. In this situation, firmware may miss
power mode change request from driver and leads to status
error. So we change driver to call power_mode_change at most
three times to make sure firmware could get the request.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220819064811.37700-2-pkshih@realtek.com
TX power byrate:
doesn't change
TX power limit:
configure values for KCC and UK
refine a bit configuration vales
TX power limit_ru:
configure values for KCC and UK
refine a bit configuration values
change 6GHz to follow indoor setting
configure 6GHz values for ETSI
TX power shape:
change with TX power limit/limit_ru
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220812093116.56791-4-pkshih@realtek.com
