[ Upstream commit d074bf9600 ]
When IPv6 is compiled but disabled at runtime, __vxlan_sock_add returns
-EAFNOSUPPORT. For metadata based tunnels, this causes failure of the whole
operation of bringing up the tunnel.
Ignore failure of IPv6 socket creation for metadata based tunnels caused by
IPv6 not being available.
Fixes: b1be00a6c3 ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2d6f1da168 ]
Before attempting to schedule a work-item onto hu->write_work in
hci_uart_tx_wakeup(), check that the Data Link protocol layer is
still bound to the HCI UART driver.
Failure to perform this protocol check causes a race condition between
the work queue hu->write_work running hci_uart_write_work() and the
Data Link protocol layer being unbound (closed) in hci_uart_tty_close().
Note hci_uart_tty_close() does have a "cancel_work_sync(&hu->write_work)"
but it is ineffective because it cannot prevent work-items being added
to hu->write_work after cancel_work_sync() has run.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_tx_wakeup()
which prevents scheduling of the work queue when HCI_UART_PROTO_READY
is in the clear state. However, note a small race condition remains
because the hci_uart_tx_wakeup() thread can run in parallel with the
hci_uart_tty_close() thread so it is possible that a schedule of
hu->write_work can occur when HCI_UART_PROTO_READY is cleared. A complete
solution needs locking of the threads which is implemented in a future
commit.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 048e1bd3a2 ]
Before attempting to dequeue a Data Link protocol encapsulated message,
check that the Data Link protocol is still bound to the HCI UART driver.
This makes the code consistent with the usage of the other proto
function pointers.
Therefore, add a check for HCI_UART_PROTO_READY into hci_uart_dequeue()
and return NULL if the Data Link protocol is not bound.
This is needed for robustness as there is a scheduling race condition.
hci_uart_write_work() is scheduled to run via work queue hu->write_work
from hci_uart_tx_wakeup(). Therefore, there is a delay between
scheduling hci_uart_write_work() to run and hci_uart_dequeue() running
whereby the Data Link protocol layer could become unbound during the
scheduling delay. In this case, without the check, the call to the
unbound Data Link protocol layer dequeue function can crash.
It is noted that hci_uart_tty_close() has a
"cancel_work_sync(&hu->write_work)" statement but this only reduces
the window of the race condition because it is possible for a new
work-item to be added to work queue hu->write_work after the call to
cancel_work_sync(). For example, Data Link layer retransmissions can
be added to the work queue after the cancel_work_sync() has finished.
Signed-off-by: Dean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ccf80b756 ]
Because of integer computation rounding in u-boot (that sets the QE
brg-frequency DTS prop), the clk value is 99999999 Hz even though it is
100 MHz.
When setting brg clks that are exact divisors of 100 MHz, this small
differnce plays a role and can result in lower clks to be output (for
instance 20 MHz - divide by 5 - results in 16.666 MHz - divide by 6).
This patch fixes that by "forcing" the brg_clk to the nearest kHz when
the difference is below 2 integer rounding errors (i.e. 4).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c52c47e4b4 ]
I've hit a lockdep splat with generic/270 test complaining that:
3216.fsstress.b/3533 is trying to acquire lock:
(jbd2_handle){++++..}, at: [<ffffffff813152e0>] jbd2_log_wait_commit+0x0/0x150
but task is already holding lock:
(jbd2_handle){++++..}, at: [<ffffffff8130bd3b>] start_this_handle+0x35b/0x850
The underlying problem is that jbd2_journal_force_commit_nested()
(called from ext4_should_retry_alloc()) may get called while a
transaction handle is started. In such case it takes care to not wait
for commit of the running transaction (which would deadlock) but only
for a commit of a transaction that is already committing (which is safe
as that doesn't wait for any filesystem locks).
In fact there are also other callers of jbd2_log_wait_commit() that take
care to pass tid of a transaction that is already committing and for
those cases, the lockdep instrumentation is too restrictive and leading
to false positive reports. Fix the problem by calling
jbd2_might_wait_for_commit() from jbd2_log_wait_commit() only if the
transaction isn't already committing.
Fixes: 1eaa566d36
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60b95d7095 ]
So far we only allowed for 1 retry and just failed the query
- and thereby high precision vblank timestamping - if we did
not get a reasonable result, as such a failure wasn't considered
all too horrible. There are a few NVidia gpu models out there which
may need a bit more than 1 retry to get a successful query result
under some conditions.
Since Linux 4.4 the update code for vblank counter and timestamp
in drm_update_vblank_count() changed so that the implementation
assumes that high precision vblank timestamping of a kms driver
either consistently succeeds or consistently fails for a given
video mode and encoder/connector combo. Iow. switching from success
to fail or vice versa on a modeset or connector change is ok, but
spurious temporary failure for a given setup can confuse the core
code and potentially cause bad miscounting of vblanks and confusion
or hangs in userspace clients which rely on vblank stuff, e.g.,
desktop compositors.
Therefore change the max retry count to a larger number - more than
any gpu so far is known to need to succeed, but still low enough
so that these queries which do also happen in vblank interrupt are
still fast enough to be not disastrously long if something would
go badly wrong with them.
As such sporadic retries only happen seldom even on affected gpu's,
this could mean a vblank irq could take a few dozen microseconds
longer every few hours of uptime -- better than a desktop compositor
randomly hanging every couple of hours or days of uptime in a hard
to reproduce manner.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2bde7c32b1 ]
The power table addresses should be contiguous, but there was a hole
where 0x34 was missing. On most devices this is not a problem as
addresses above 0x34 are used for the BUC# convertors which are not
used in the DSDTs I've access to but after the BUC# convertors
there is a field named GPI1 in the DSTDs, which does get used in some
cases and ended up turning BUC6 on and off due to the wrong addresses,
resulting in turning the entire device off (or causing it to reboot).
Removing the hole in the addresses fixes this, fixing one of my
Bay Trail tablets turning off while booting the mainline kernel.
While at it add comments with the field names used in the DSDTs to
make it easier to compare the register and bits used at each address
with the datasheet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c1175c2e8 ]
Commit c49c097610 ("ipmi: Don't call receive handler in the
panic context") means that the panic_recv_free is not called during a
panic and the atomic count does not drop to 0.
Fix this by only expecting one decrement of the atomic variable
which comes from panic_smi_free.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9b6151868 ]
some laptops, for example ASUS UX330UAK, have brocken als_get function
but working als_set funktion. In this case, ALS will stay turned off.
Method (WMNB, 3, Serialized)
{
...
If (Local0 == 0x53545344)
{
...
If (IIA0 == 0x00050001)
{
If (!ALSP)
{
Return (0x02)
}
Local0 = (GALS & 0x10) <<<---- bug,
should be: (GALS () & 0x10)
If (Local0)
{
Return (0x00050001)
}
Else
{
Return (0x00050000)
}
}
.....
If (Local0 == 0x53564544)
{
...
If (IIA0 == 0x00050001)
{
Return (ALSC (IIA1))
}
......
Method (GALS, 0, NotSerialized)
{
Local0 = Zero
Local0 |= 0x20
If (ALAE)
{
Local0 |= 0x10
}
Local1 = 0x0A
Local1 <<= 0x08
Local0 |= Local1
Return (Local0)
}
Since it works without problems on Windows I assume ASUS WMI driver for Win
never trying to get ALS state, and instead it is setting it by default to ON.
This patch will do the same. Turn ALS on by default.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c949ce38f ]
The PCIe programming sequence in TRM suggests CLKSTCTRL of PCIe should be
set to SW_WKUP. There are no issues when CLKSTCTRL is set to HW_AUTO in RC
mode. However in EP mode, the host system is not able to access the
MEMSPACE and setting the CLKSTCTRL to SW_WKUP fixes it.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21a8e9dd52 ]
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1442f6f7c1 ]
When creating a new ipvs service, ipv6 addresses are always accepted
if CONFIG_IP_VS_IPV6 is enabled. On dest creation the address family
is not explicitly checked.
This allows the user-space to configure ipvs services even if the
system is booted with ipv6.disable=1. On specific configuration, ipvs
can try to call ipv6 routing code at setup time, causing the kernel to
oops due to fib6_rules_ops being NULL.
This change addresses the issue adding a check for the ipv6
module being enabled while validating ipv6 service operations and
adding the same validation for dest operations.
According to git history, this issue is apparently present since
the introduction of ipv6 support, and the oops can be triggered
since commit 09571c7ae3 ("IPVS: Add function to determine
if IPv6 address is local")
Fixes: 09571c7ae3 ("IPVS: Add function to determine if IPv6 address is local")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e96652756 ]
Function dev_alloc_skb() will return a NULL pointer if there is no
enough memory. However, in function WILC_WFI_mon_xmit(), its return
value is used without validation. This may result in a bad memory access
bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c2bf0bd08 ]
The root issue is that we are not allowed to have items on the
stack being passed to "DMA" like operations. In this case we have
a vmcall and an inline completion of scsi command.
This patch fixes the issue by moving the variables on stack in
do_scsi_nolinuxstat() to heap memory.
Signed-off-by: Sameer Wadgaonkar <sameer.wadgaonkar@unisys.com>
Signed-off-by: David Kershner <david.kershner@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da63b6b200 ]
Dave found that a kdump kernel with KASLR enabled will reset to the BIOS
immediately if physical randomization failed to find a new position for
the kernel. A kernel with the 'nokaslr' option works in this case.
The reason is that KASLR will install a new page table for the identity
mapping, while it missed building it for the original kernel location
if KASLR physical randomization fails.
This only happens in the kexec/kdump kernel, because the identity mapping
has been built for kexec/kdump in the 1st kernel for the whole memory by
calling init_pgtable(). Here if physical randomizaiton fails, it won't build
the identity mapping for the original area of the kernel but change to a
new page table '_pgtable'. Then the kernel will triple fault immediately
caused by no identity mappings.
The normal kernel won't see this bug, because it comes here via startup_32()
and CR3 will be set to _pgtable already. In startup_32() the identity
mapping is built for the 0~4G area. In KASLR we just append to the existing
area instead of entirely overwriting it for on-demand identity mapping
building. So the identity mapping for the original area of kernel is still
there.
To fix it we just switch to the new identity mapping page table when physical
KASLR succeeds. Otherwise we keep the old page table unchanged just like
"nokaslr" does.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1493278940-5885-1-git-send-email-bhe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4e84aae81 ]
mtip32xx supposes that 'request_idx' passed to .init_request()
is tag of the request, and use that as request's tag to initialize
command header.
After MQ IO scheduler is in, request tag assigned isn't same with
the request index anymore, so cause strange hardware failure on
mtip32xx, even whole system panic is triggered.
This patch fixes the issue by initializing command header via
request's real tag.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85fdaf8eb9 ]
POWERHOLD signal has higher priority over the DEV_ON bit.
So power off will not happen if the POWERHOLD is held high.
Hence reset the MUX to GPIO_7 mode to release the POWERHOLD
and the DEV_ON bit to take effect to power off the PMIC.
PMIC Power off happens in dire situations like thermal shutdown
so irrespective of the POWERHOLD setting go ahead and turn off
the powerhold. Currently poweroff is broken on boards that have
powerhold enabled. This fixes poweroff on those boards.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8461cf20d1 ]
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. To let the device tree describe which mode of operation is needed,
this patch introduces a new property "xpowers,master-mode".
Fixes: 204ae2963e ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c894acc7bf ]
Ensure that when an invalid value in ret or value is found -EINVAL
is returned. A previous commit broke the way the return error is
being returned and instead caused the return code in ret to be
re-assigned rather than be returned.
Fixes: 5d9854eaea ("iio: hid-sensor: Store restore poll and hysteresis on S3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf147085fd ]
ieee80211_frame_acked is called when a frame is acked by
the peer. In case this is a management frame, we check
if this an SMPS frame, in which case we can update our
antenna configuration.
When we parse the management frame we look at the category
in case it is an action frame. That byte sits after the IV
in case the frame was encrypted. This means that if the
frame was encrypted, we basically look at the IV instead
of looking at the category. It is then theorically
possible that we think that an SMPS action frame was acked
where really we had another frame that was encrypted.
Since the only management frame whose ack needs to be
tracked is the SMPS action frame, and that frame is not
a robust management frame, it will never be encrypted.
The easiest way to fix this problem is then to not look
at frames that were encrypted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5a9d61eeb ]
When the computer is turned off, all the processes are killed and then
all the filesystems are umounted. OrangeFS should not wait for the
userspace daemon to come back in that case.
This only works for plain umount(2). To actually take advantage of this
interactively, `umount -f' is needed; otherwise umount will issue a
statfs first, which will wait for the userspace daemon to come back.
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be2d253cc9 ]
If the call to btrfs_qgroup_reserve_data() failed, we were leaking an
extent map structure. The failure can happen either due to an -ENOMEM
condition or, when quotas are enabled, due to -EDQUOT for example.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1cbfd7bf6 ]
Normally we don't have inline extents followed by regular extents, but
there's currently at least one harmless case where this happens. For
example, when the page size is 4Kb and compression is enabled:
$ mkfs.btrfs -f /dev/sdb
$ mount -o compress /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0xaa 0 4K" -c "fsync" /mnt/foobar
$ xfs_io -c "pwrite -S 0xbb 8K 4K" -c "fsync" /mnt/foobar
In this case we get a compressed inline extent, representing 4Kb of
data, followed by a hole extent and then a regular data extent. The
inline extent was not expanded/converted to a regular extent exactly
because it represents 4Kb of data. This does not cause any apparent
problem (such as the issue solved by commit e1699d2d7b
("btrfs: add missing memset while reading compressed inline extents"))
except trigger an unexpected case in the incremental send code path
that makes us issue an operation to write a hole when it's not needed,
resulting in more writes at the receiver and wasting space at the
receiver.
So teach the incremental send code to deal with this particular case.
The issue can be currently triggered by running fstests btrfs/137 with
compression enabled (MOUNT_OPTIONS="-o compress" ./check btrfs/137).
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9dc7efd397 ]
Function create_singlethread_workqueue() will return a NULL pointer if
there is no enough memory, and its return value should be validated
before using. However, in function rndis_wlan_bind(), its return value
is not checked. This may cause NULL dereference bugs. This patch fixes
it.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dc3f89c38a ]
Function alloc_workqueue() will return a NULL pointer if there is no
enough memory, and its return value should be validated before using.
However, in function if_spi_probe(), its return value is not checked.
This may result in a NULL dereference bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fb01e91da ]
Function alloc_skb() will return a NULL pointer if there is no enough
memory. However, in function mt7601u_mcu_msg_alloc(), its return value
is not validated before it is used. This patch fixes it.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7383d44b84 ]
This patch fixes the sensor platform data initialisation for st_pressure
and st_accel device drivers. Without this patch, the driver fails to
register the sensors when the user removes and re-loads the driver.
1. Unload the kernel modules for st_pressure
$ sudo rmmod st_pressure_i2c
$ sudo rmmod st_pressure
2. Re-load the driver
$ sudo insmod st_pressure
$ sudo insmod st_pressure_i2c
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99bbf6ecc6 ]
consider the sequence of commands:
mkdir -p /import/nfs /import/bind /import/etc
mount --bind / /import/bind
mount --make-private /import/bind
mount --bind /import/etc /import/bind/etc
exportfs -o rw,no_root_squash,crossmnt,async,no_subtree_check localhost:/
mount -o vers=4 localhost:/ /import/nfs
ls -l /import/nfs/etc
You would not expect this to report a stale file handle.
Yet it does.
The manipulations under /import/bind cause the dentry for
/etc to get the DCACHE_MOUNTED flag set, even though nothing
is mounted on /etc. This causes nfsd to call
nfsd_cross_mnt() even though there is no mountpoint. So an
upcall to mountd for "/etc" is performed.
The 'crossmnt' flag on the export of / causes mountd to
report that /etc is exported as it is a descendant of /. It
assumes the kernel wouldn't ask about something that wasn't
a mountpoint. The filehandle returned identifies the
filesystem and the inode number of /etc.
When this filehandle is presented to rpc.mountd, via
"nfsd.fh", the inode cannot be found associated with any
name in /etc/exports, or with any mountpoint listed by
getmntent(). So rpc.mountd says the filehandle doesn't
exist. Hence ESTALE.
This is fixed by teaching nfsd not to trust DCACHE_MOUNTED
too much. It is just a hint, not a guarantee.
Change nfsd_mountpoint() to return '1' for a certain mountpoint,
'2' for a possible mountpoint, and 0 otherwise.
Then change nfsd_crossmnt() to check if follow_down()
actually found a mountpount and, if not, to avoid performing
a lookup if the location is not known to certainly require
an export-point.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6aeafd05ec ]
The assumption should be that if the caller returns PNFS_ATTEMPTED, then hdr
has been consumed, and so we should not be testing hdr->task.tk_status.
If the caller returns PNFS_TRY_AGAIN, then we need to recoalesce and
free hdr.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f7f4dcfff ]
The 'num_sge' variable is verfied to be smaller than the 'sge_count'
variable; however, since both are user-controlled it's possible to cause
an integer overflow for the kmalloc multiply on 32-bit platforms
(num_sge and sge_count are both defined u32). By crafting an input that
causes a smaller-than-expected allocation it's possible to write
controlled data out-of-bounds.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4da2b1eb23 ]
Commit da244654c6 ("[SCSI] mac_esp: fix for quadras with two esp
chips") added mac_scsi_esp_intr() to handle the IRQ lines from a pair of
on-board ESP chips (a normal shared IRQ did not work).
Proper mutual exclusion was missing from that patch. This patch fixes
race conditions between comparison and assignment of esp_chips[]
pointers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 277a292835 ]
Currently, after adding the following nft rules:
# nft add set x target1 { type ipv4_addr \; flags timeout \;}
# nft add rule x y set add ip daddr timeout 1d @target1 counter
the counters will always be zero despite of the elements are added
to the dynamic set "target1" or not, as we will break the nft expr
traversal unconditionally:
# nft list ruleset
...
set target1 {
...
elements = { 8.8.8.8 expires 23h59m53s}
}
chain output {
...
set add ip daddr timeout 1d @target1 counter packets 0 bytes 0
^ ^
...
}
Since we add the elements to the set successfully, we should continue
to the next expression.
Additionally, if elements are added to "flow table" successfully, we
will _always_ continue to the next expr, even if the operation is
_OP_ADD. So it's better to keep them to be consistent.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91ec701a55 ]
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function qlcnic_sriov_virtid_fn(), its return value is used
without validation. This may result in invalid memory access bugs. This
patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a39e7aa8a ]
In function pc300_pci_init_one(), on the ioremap error path, function
pc300_pci_remove_one() is called to free the allocated memory. However,
the path is not terminated, and the freed memory will be used later,
resulting in use-after-free bugs. This path fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78302fd405 ]
Function nlmsg_new() will return a NULL pointer if there is no enough
memory, and its return value should be checked before it is used.
However, in function tipc_nl_node_get_monitor(), the validation of the
return value of function nlmsg_new() is missed. This patch fixes the
bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66e5a6b18b ]
cthelpers added via nfnetlink may have the same tuple, i.e. except for
the l3proto and l4proto, other fields are all zero. So even with the
different names, we will also fail to add them:
# nfct helper add ssdp inet udp
# nfct helper add tftp inet udp
nfct v1.4.3: netlink error: File exists
So in order to avoid unpredictable behaviour, we should:
1. cthelpers can be selected by nft ct helper obj or xt_CT target, so
report error if duplicated { name, l3proto, l4proto } tuple exist.
2. cthelpers can be selected by nf_ct_tuple_src_mask_cmp when
nf_ct_auto_assign_helper is enabled, so also report error if duplicated
{ l3proto, l4proto, src-port } tuple exist.
Also note, if the cthelper is added from userspace, then the src-port will
always be zero, it's invalid for nf_ct_auto_assign_helper, so there's no
need to check the second point listed above.
Fixes: 893e093c78 ("netfilter: nf_ct_helper: bail out on duplicated helpers")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
