commit f971a85439 upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4eb8223 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a006acb931 upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4db66499df ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1b9ca365d upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 9cbee35868 ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f8765a11 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b16bef60a9 upstream.
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c78a5e7aa upstream.
In open_ctree() in btrfs_check_rw_degradable() [1], we check each block
group individually if at least the minimum number of devices is available
for that profile. If all the devices are available, then we don't have to
check degradable.
[1]
open_ctree()
::
3559 if (!sb_rdonly(sb) && !btrfs_check_rw_degradable(fs_info, NULL)) {
Also before calling btrfs_check_rw_degradable() in open_ctee() at the
line number shown below [2] we call btrfs_read_chunk_tree() and down to
add_missing_dev() to record number of missing devices.
[2]
open_ctree()
::
3454 ret = btrfs_read_chunk_tree(fs_info);
btrfs_read_chunk_tree()
read_one_chunk() / read_one_dev()
add_missing_dev()
So, check if there is any missing device before btrfs_check_rw_degradable()
in open_ctree().
Also, with this the mount command could save ~16ms.[3] in the most
common case, that is no device is missing.
[3]
1) * 16934.96 us | btrfs_check_rw_degradable [btrfs]();
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10adb1152d upstream.
At replay_dir_deletes(), if find_dir_range() returns an error we break out
of the main while loop and then assign a value of 0 (success) to the 'ret'
variable, resulting in completely ignoring that an error happened. Fix
that by jumping to the 'out' label when find_dir_range() returns an error
(negative value).
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d03dbebba upstream.
Reported bug: https://github.com/kdave/btrfs-progs/issues/389
There's a problem with scrub reporting aborted status but returning
error code 0, on a filesystem with missing and readded device.
Roughly these steps:
- mkfs -d raid1 dev1 dev2
- fill with data
- unmount
- make dev1 disappear
- mount -o degraded
- copy more data
- make dev1 appear again
Running scrub afterwards reports that the command was aborted, but the
system log message says the exit code was 0.
It seems that the cause of the error is decrementing
fs_devices->missing_devices but not clearing device->dev_state. Every
time we umount filesystem, it would call close_ctree, And it would
eventually involve btrfs_close_one_device to close the device, but it
only decrements fs_devices->missing_devices but does not clear the
device BTRFS_DEV_STATE_MISSING bit. Worse, this bug will cause Integer
Overflow, because every time umount, fs_devices->missing_devices will
decrease. If fs_devices->missing_devices value hit 0, it would overflow.
With added debugging:
loop1: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 1 transid 21 /dev/loop1 scanned by systemd-udevd (2311)
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 56ad51f1-5523-463b-8547-c19486c51ebb devid 2 transid 17 /dev/loop2 scanned by systemd-udevd (2313)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 0
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): using free space tree
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000f706684d /dev/loop1 18446744073709551615
BTRFS warning (device loop1): devid 2 uuid 6635ac31-56dd-4852-873b-c60f5e2d53d2 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 18446744073709551615
If fs_devices->missing_devices is 0, next time it would be 18446744073709551615
After apply this patch, the fs_devices->missing_devices seems to be
right:
$ truncate -s 10g test1
$ truncate -s 10g test2
$ losetup /dev/loop1 test1
$ losetup /dev/loop2 test2
$ mkfs.btrfs -draid1 -mraid1 /dev/loop1 /dev/loop2 -f
$ losetup -d /dev/loop2
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ mount -o degraded /dev/loop1 /mnt/1
$ umount /mnt/1
$ dmesg
loop1: detected capacity change from 0 to 20971520
loop2: detected capacity change from 0 to 20971520
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 1 transid 5 /dev/loop1 scanned by mkfs.btrfs (1863)
BTRFS: device fsid 15aa1203-98d3-4a66-bcae-ca82f629c2cd devid 2 transid 5 /dev/loop2 scanned by mkfs.btrfs (1863)
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): checking UUID tree
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
BTRFS info (device loop1): flagging fs with big metadata feature
BTRFS info (device loop1): allowing degraded mounts
BTRFS info (device loop1): disk space caching is enabled
BTRFS info (device loop1): has skinny extents
BTRFS info (device loop1): before clear_missing.00000000975bd577 /dev/loop1 0
BTRFS warning (device loop1): devid 2 uuid 8b333791-0b3f-4f57-b449-1c1ab6b51f38 is missing
BTRFS info (device loop1): before clear_missing.0000000000000000 /dev/loop2 1
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Li Zhang <zhanglikernel@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90a881fc35 ]
MTU change is refused whenever the value of new MTU is bigger than
the max packet bytes that fits in NFP Cluster Target Memory (CTM).
However, an eBPF program doesn't always need to access the whole
packet data.
The maximum direct packet access (DPA) offset has always been
caculated by verifier and stored in the max_pkt_offset field of prog
aux data.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9159f10240 ]
The netif_device_detach() conditionally stops all tx queues if the queues
are running. There is no need to call netif_tx_stop_all_queues() again.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86aeda32b8 ]
Pass the correct length to nvmet_tcp_verify_hdgst, which is the pdu
header length. This fixes a wrong behaviour where header digest
verification passes although the digest is wrong.
Signed-off-by: Amit Engel <amit.engel@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9122a70a63 ]
During a testing of an user-space application which transmits UDP
multicast datagrams and utilizes multicast routing to send the UDP
datagrams out of defined network interfaces, I've found a multicast
router does not fill-in UDP checksum into locally produced, looped-back
and forwarded UDP datagrams, if an original output NIC the datagrams
are sent to has UDP TX checksum offload enabled.
The datagrams are sent malformed out of the NIC the datagrams have been
forwarded to.
It is because:
1. If TX checksum offload is enabled on the output NIC, UDP checksum
is not calculated by kernel and is not filled into skb data.
2. dev_loopback_xmit(), which is called solely by
ip_mc_finish_output(), sets skb->ip_summed = CHECKSUM_UNNECESSARY
unconditionally.
3. Since 35fc92a9 ("[NET]: Allow forwarding of ip_summed except
CHECKSUM_COMPLETE"), the ip_summed value is preserved during
forwarding.
4. If ip_summed != CHECKSUM_PARTIAL, checksum is not calculated during
a packet egress.
The minimum fix in dev_loopback_xmit():
1. Preserves skb->ip_summed CHECKSUM_PARTIAL. This is the
case when the original output NIC has TX checksum offload enabled.
The effects are:
a) If the forwarding destination interface supports TX checksum
offloading, the NIC driver is responsible to fill-in the
checksum.
b) If the forwarding destination interface does NOT support TX
checksum offloading, checksums are filled-in by kernel before
skb is submitted to the NIC driver.
c) For local delivery, checksum validation is skipped as in the
case of CHECKSUM_UNNECESSARY, thanks to skb_csum_unnecessary().
2. Translates ip_summed CHECKSUM_NONE to CHECKSUM_UNNECESSARY. It
means, for CHECKSUM_NONE, the behavior is unmodified and is there
to skip a looped-back packet local delivery checksum validation.
Signed-off-by: Cyril Strejc <cyril.strejc@skoda.cz>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 926245c7d2 ]
page_frag_free() won't completely release the memory
allocated for the commands, the cache page must be explicitly
freed by calling __page_frag_cache_drain().
This bug can be easily reproduced by repeatedly
executing the following command on the initiator:
$echo 1 > /sys/devices/virtual/nvme-fabrics/ctl/nvme0/reset_controller
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 042b2046d0 ]
The tx queues are not stopped during the live migration. As a result, the
ndo_start_xmit() may access netfront_info->queues which is freed by
talk_to_netback()->xennet_destroy_queues().
This patch is to netif_device_detach() at the beginning of xen-netfront
resuming, and netif_device_attach() at the end of resuming.
CPU A CPU B
talk_to_netback()
-> if (info->queues)
xennet_destroy_queues(info);
to free netfront_info->queues
xennet_start_xmit()
to access netfront_info->queues
-> err = xennet_create_queues(info, &num_queues);
The idea is borrowed from virtio-net.
Cc: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162079f2dc ]
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dd7e0590 ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the A20-olinuxino-lime2 board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210916081721.237137-1-rouca@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8017c99680 ]
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Include the correct header first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211018131929.2260087-1-arnd@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf6abf345d ]
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69b2f4687 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a8f71014b ]
The sgl is freed in the target stack in target_release_cmd_kref() before
calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that
causes a panic if sgl is not yet DMA unmapped:
NIP dma_direct_unmap_sg+0xdc/0x180
LR dma_direct_unmap_sg+0xc8/0x180
Call Trace:
ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable)
dma_unmap_sg_attrs+0x54/0xf0
qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx]
qlt_free_cmd+0x124/0x1d0 [qla2xxx]
tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx]
target_put_sess_cmd+0x198/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]
The sgl may be left unmapped in error cases of response sending. For
instance, qlt_rdy_to_xfer() maps sgl and exits when session is being
deleted keeping the sgl mapped.
This patch removes use-after-free of the sgl and ensures that the sgl is
unmapped for any command that was not sent to firmware.
Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cddb44bd ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ff53f6a43 upstream.
Add a synchronize_rcu() after clearing the posted interrupt wakeup handler
to ensure all readers, i.e. in-flight IRQ handlers, see the new handler
before returning to the caller. If the caller is an exiting module and
is unregistering its handler, failure to wait could result in the IRQ
handler jumping into an unloaded module.
The registration path doesn't require synchronization, as it's the
caller's responsibility to not generate interrupts it cares about until
after its handler is registered.
Fixes: f6b3c72c23 ("x86/irq: Define a global vector for VT-d Posted-Interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211009001107.3936588-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415de44076 upstream.
Currently, Linux probes for X86_BUG_NULL_SEL unconditionally which
makes it unsafe to migrate in a virtualised environment as the
properties across the migration pool might differ.
To be specific, the case which goes wrong is:
1. Zen1 (or earlier) and Zen2 (or later) in a migration pool
2. Linux boots on Zen2, probes and finds the absence of X86_BUG_NULL_SEL
3. Linux is then migrated to Zen1
Linux is now running on a X86_BUG_NULL_SEL-impacted CPU while believing
that the bug is fixed.
The only way to address the problem is to fully trust the "no longer
affected" CPUID bit when virtualised, because in the above case it would
be clear deliberately to indicate the fact "you might migrate to
somewhere which has this behaviour".
Zen3 adds the NullSelectorClearsBase CPUID bit to indicate that loading
a NULL segment selector zeroes the base and limit fields, as well as
just attributes. Zen2 also has this behaviour but doesn't have the NSCB
bit.
[ bp: Minor touchups. ]
Signed-off-by: Jane Malalane <jane.malalane@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211021104744.24126-1-jane.malalane@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d445ab26 upstream.
When runtime support for converting between 4-level and 5-level pagetables
was added to the kernel, the SME code that built pagetables was updated
to use the pagetable functions, e.g. p4d_offset(), etc., in order to
simplify the code. However, the use of the pagetable functions in early
boot code requires the use of the USE_EARLY_PGTABLE_L5 #define in order to
ensure that the proper definition of pgtable_l5_enabled() is used.
Without the #define, pgtable_l5_enabled() is #defined as
cpu_feature_enabled(X86_FEATURE_LA57). In early boot, the CPU features
have not yet been discovered and populated, so pgtable_l5_enabled() will
return false even when 5-level paging is enabled. This causes the SME code
to always build 4-level pagetables to perform the in-place encryption.
If 5-level paging is enabled, switching to the SME pagetables results in
a page-fault that kills the boot.
Adding the #define results in pgtable_l5_enabled() using the
__pgtable_l5_enabled variable set in early boot and the SME code building
pagetables for the proper paging level.
Fixes: aad983913d ("x86/mm/encrypt: Simplify sme_populate_pgd() and sme_populate_pgd_large()")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.18.x
Link: https://lkml.kernel.org/r/2cb8329655f5c753905812d951e212022a480475.1634318656.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 712a951025 upstream.
It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.
The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).
This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.
Fix by calling pipe_buf_release() right after the page was inserted into
the page cache. In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.
Reported-by: Frank Dinoff <fdinoff@google.com>
Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1yw@mail.gmail.com/
Fixes: dd3bb14f44 ("fuse: support splice() writing to fuse device")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0317c0e87 upstream.
When the timer instance was add into ack_list but was not currently in
process, the user could stop it via snd_timer_stop1() without delete it
from the ack_list. Then the user could free the timer instance and when
it was actually processed UAF occurred.
This issue could be reproduced via testcase snd_timer01 in ltp - running
several instances of that testcase at the same time.
What I actually met was that the ack_list of the timer broken and the
kernel went into deadloop with irqoff. That could be detected by
hardlockup detector on board or when we run it on qemu, we could use gdb
to dump the ack_list when the console has no response.
To fix this issue, we delete the timer instance from ack_list and
active_list unconditionally in snd_timer_stop1().
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211103033517.80531-1-wangwensheng4@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
